aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2022-07-06arm64: dts: qcom: sc7180-idp: add vdds supply to the DSI PHYDmitry Baryshkov1-0/+1
Add the (required) vdss-supply property to the DSI PHY node. Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: sc7280: use constants for gpucc clocks and power-domainsDmitry Baryshkov1-16/+16
To ease merging of bindings and dts files, the constants were replaced with numeric values. Change them back to defined constants. While we are at it, fix the indentation of these clocks properties to follow established guidelines. Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: msm8996: add missing DSI clock assignmentsDmitry Baryshkov1-0/+4
Add missing DSI clock assignments to properly use DSI PHY clocks as DSI byte and pixel clock parents. Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: ipq8074: add reset to SDHCIRobert Marko1-0/+1
Add reset to SDHCI controller so it can be reset to avoid timeout issues after software reset due to bootloader set configuration. Signed-off-by: Robert Marko <[email protected]> Reviewed-by: Konrad Dybcio <[email protected]> Acked-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: sdm845: Add CPU BWMONKrzysztof Kozlowski1-0/+37
Add device node for CPU-memory BWMON device (bandwidth monitoring) on SDM845 measuring bandwidth between CPU (gladiator_noc) and Last Level Cache (memnoc). Usage of this BWMON allows to remove fixed bandwidth votes from cpufreq (CPU nodes) thus achieve high memory throughput even with lower CPU frequencies. Co-developed-by: Thara Gopinath <[email protected]> Signed-off-by: Thara Gopinath <[email protected]> Signed-off-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: ipq8074: move ARMv8 timer out of SoC nodeRobert Marko1-8/+8
The ARM timer is usually considered not part of SoC node, just like other ARM designed blocks (PMU, PSCI). This fixes dtbs_check warning: arch/arm64/boot/dts/qcom/ipq8072-ax9000.dtb: soc: timer: {'compatible': ['arm,armv8-timer'], 'interrupts': [[1, 2, 3848], [1, 3, 3848], [1, 4, 3848], [1, 1, 3848]]} should not be valid under {'type': 'object'} From schema: dtschema/schemas/simple-bus.yaml Signed-off-by: Robert Marko <[email protected]> Acked-by: Krzysztof Kozlowski <[email protected]> [bjorn: Moved node after "soc" for alphabetical ordering] Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dta: qcom: sc7180: delete vdda-1p2 and vdda-0p9 from mdss_dpKuogee Hsieh1-2/+0
Both vdda-1p2-supply and vdda-0p9-supply regulators are controlled by dp combo phy. Therefore remove them from dp controller. Signed-off-by: Kuogee Hsieh <[email protected]> Reviewed-by: Douglas Anderson <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: sdm845: Switch PSCI cpu idle states from PC to OSIAbel Vesa2-54/+213
Switch from the flat PC idle states of sdm845 to OSI hierarchical idle states. The exceptions are the cheza plaftorms, which need to remain with PC idle states. So in order allow all the other platforms to switch, while cheza platforms to remain the same, replace the PC idle states with the OSI ones in the main SDM845 dtsi, and then override the inherited OSI states with PC ones, delete inherited psci cpus nodes, domain idle states and power domain properties. Signed-off-by: Abel Vesa <[email protected]> Tested-by: Steev Klimaszewski <[email protected]> Acked-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: extend scm compatible stringsDavid Heidelberg4-4/+4
First device specific compatible, then general one. Reviewed-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: David Heidelberg <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: add device tree for LG G7 and LG V35Anton Bambura4-0/+728
Adds initial support for the LG G7 (judyln) and LG V35 (judyp) phones. Currently supported features: - Display via simplefb (panel driver is WIP) - Keys - Micro SD card - Modem (not tested much, but initialises) - UFS (crashes during intensive workloads, may need quirks) - USB in peripheral mode Notable missing features: - Enabling WiFi causes a remoteproc crash, so it's disabled here. Needs to be debugged - ideas welcome! Signed-off-by: Anton Bambura <[email protected]> Signed-off-by: Stefan Hansson <[email protected]> Tested-by: Gregari Ivanov <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: msm8996: add xo clock source to rpmccDmitry Baryshkov1-0/+2
Add XO clock source to the RPM clock controller. Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: msm8996: add GCC's optional clock sourcesDmitry Baryshkov1-2/+16
Add missing GCC clock sources. This includes PCIe and USB PIPE and UFS symbol clocks. Signed-off-by: Dmitry Baryshkov <[email protected]> Acked-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: msm8996: correct #clock-cells for QMP PHY nodesDmitry Baryshkov1-2/+4
The commit 82d61e19fccb ("arm64: dts: qcom: msm8996: Move '#clock-cells' to QMP PHY child node") moved the '#clock-cells' properties to the child nodes. However it missed the fact that the property must have been set to <0> (as all pipe clocks use of_clk_hw_simple_get as the xlate function. Also the mentioned commit didn't add '#clock-cells' properties to second and third PCIe PHY nodes. Correct both these mistakes: - Set '#clock-cells' to <0>, - Add the property to pciephy_1 and pciephy_2 nodes. Fixes: 82d61e19fccb ("arm64: dts: qcom: msm8996: Move '#clock-cells' to QMP PHY child node") Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: sdm845-shift-axolotl: Enable pmi9889 LPG LEDDylan Van Assche1-0/+29
Enables the RGB notification LED on the SHIFT 6mq (sdm845-shift-axolotl) with the Qualcomm Light Pulse Generator bindings by Bjorn Andersson [1]. Patches are merged in for-next branch of linux-leds. Tested these changes on the SHIFT 6mq. [1] https://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds.git/commit/?h=for-next&id=a8e53db46f19f67be6a26488aafb7d10c78e33bd Signed-off-by: Dylan Van Assche <[email protected]> Reviewed-by: Alexander Martinz <[email protected]> Tested-by: Alexander Martinz <[email protected]> Tested-by: Caleb Connolly <[email protected]> Reviewed-by: Caleb Connolly <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: ti: k3-am62-main: Enable crypto acceleratorJayesh Choudhary1-0/+13
Add the node for sa3ul crypto accelerator. Signed-off-by: Jayesh Choudhary <[email protected]> Signed-off-by: Nishanth Menon <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: ti: k3-am625-sk: Enable ramoopsGuillaume La Roque1-0/+9
Enable ramoops features to easily debug some issues. Signed-off-by: Guillaume La Roque <[email protected]> Signed-off-by: Kevin Hilman <[email protected]> Signed-off-by: Nishanth Menon <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: ti: k3-am642-sk: Add pinmux corresponding to main_uart0Aswath Govindraju1-0/+14
Add pinmux details required for the zeroth instance of main UART. Signed-off-by: Aswath Govindraju <[email protected]> Signed-off-by: Nishanth Menon <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06ARM: dts: qcom: msm8974: rename GPU's OPP table nodeDmitry Baryshkov1-1/+1
Rename the GPU's opp table node to make it follow the display/msm/gpu.yaml schema. Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06ARM: dts: qcom: apq8064: disable DSI and DSI PHY by defaultDmitry Baryshkov1-0/+3
Disable DSI and DSI PHY devices by default. The only actual user, Nexus 7, already contains `status = "okay"` property in the respective devices nodes. Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06ARM: dts: qcom: apq8064: rename DSI PHY iface clockDmitry Baryshkov1-1/+1
Follow the usual scheme and use name 'iface' rather than 'iface_clk' for the interface clock. The DSI PHY driver can cope with both of them, so there is no breakage. Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06ARM: dts: qcom: extend scm compatible to match dt-schemaDavid Heidelberg4-4/+4
First device specific compatible, then general one. Reviewed-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: David Heidelberg <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06Merge tag 'dt-cleanup-5.20-2' of ↵Arnd Bergmann91-348/+301
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt Cleanup of ARM DTS for v5.20, part two Series of cleanups for ARM DTS - white-spaces, gpio-key subnode names and gpio-key properties for more boards: TI, Marvell, AT91 and Aspeed. * tag 'dt-cleanup-5.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: ARM: dts: aspeed: correct gpio-keys properties ARM: dts: aspeed: align gpio-key node names with dtschema ARM: dts: at91: drop unneeded status from gpio-keys ARM: dts: at91: correct gpio-keys properties ARM: dts: at91: align gpio-key node names with dtschema ARM: dts: omap: correct gpio-keys properties ARM: dts: omap: align gpio-key node names with dtschema ARM: dts: marvell: correct gpio-keys properties ARM: dts: marvell: align gpio-key node names with dtschema ARM: dts: omap: adjust whitespace around '=' ARM: dts: ti: adjust whitespace around '=' Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnd Bergmann <[email protected]>
2022-07-06Merge tag 'dt64-cleanup-5.20-2' of ↵Arnd Bergmann2-4/+4
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt Cleanup of ARM64 DTS for v5.20, part two Remaining cleanups for ARM64 DTS: gpio-keys and led node names on Marvel platforms. * tag 'dt64-cleanup-5.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: arm64: dts: marvell: armada-3720: align lednode names with dtschema arm64: dts: marvell: align gpio-key node names with dtschema Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnd Bergmann <[email protected]>
2022-07-06arm64: dts: qcom: sm6125: Add DLL/DDR configuration on SDHCI 1/2Marijn Suijten1-0/+6
These config values have been extracted from CodeLinaro's most recent trinket/sm6125 tag: https://git.codelinaro.org/clo/la/kernel/msm-4.14/-/blob/LA.UM.9.11.r1-05600-NICOBAR.QSSI12.0/arch/arm64/boot/dts/qcom/trinket.dtsi Signed-off-by: Marijn Suijten <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: sm6125: Append -state suffix to pinctrl nodesMarijn Suijten2-6/+6
According to qcom,sm6125-pinctrl.yaml all nodes inside the tlmm must be suffixed by -state: qcom/sm6125-sony-xperia-seine-pdx201.dtb: pinctrl@500000: 'sdc2-off', 'sdc2-on' do not match any of the regexes: '-state$', 'pinctrl-[0-9]+' The label names have been updated to match, going from sdc2_state_X to sdc2_X_state. Fixes: cff4bbaf2a2d ("arm64: dts: qcom: Add support for SM6125") Fixes: 82e1783890b7 ("arm64: dts: qcom: sm6125: Add support for Sony Xperia 10II") Signed-off-by: Marijn Suijten <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: sm6125: Move sdc2 pinctrl from seine-pdx201 to sm6125Marijn Suijten2-28/+30
Both the sdc2-on and sdc2-off pinctrl nodes are used by the sdhci@4784000 node in sm6125.dtsi. Surprisingly sdc2-off is defined in sm6125, yet its sdc2-on counterpart is only defined in board-specific DT for the Sony Seine PDX201 board/device resulting in an "undefined label &sdc2_state_on" error if sm6125.dtsi were included elsewhere. This sm6125 base dtsi should not rely on externally defined labels; the properties referencing it should then also be written externally. Since the sdc2-on pin configuration is board-independent just like sdc2-off, move it from seine-pdx201.dts into sm6125.dtsi. The SDCard-detect pin (gpio98) is however board-specific, and remains as an overwrite in seine-pdx201.dts for both the on and off state. As a drive-by cleanup, reorder bias- and drive-strength properties. Fixes: cff4bbaf2a2d ("arm64: dts: qcom: Add support for SM6125") Fixes: 82e1783890b7 ("arm64: dts: qcom: sm6125: Add support for Sony Xperia 10II") Signed-off-by: Marijn Suijten <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: db820c: Add user LEDsBjorn Andersson1-0/+56
The db820c has 4 "user LEDs", all connected to the PMI8994. The first three are connected to the three current sinks provided by the TRILED and the fourth is connected to MPP2. By utilizing the DTEST bus the MPP is fed the control signal from the fourth LPG block, providing a consistent interface to the user. Signed-off-by: Bjorn Andersson <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Reviewed-by: Dylan Van Assche <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: pmi8994: Define MPP blockBjorn Andersson1-0/+10
The pmi8994 has 4 multi-purpose-pins, add these to the definition. Signed-off-by: Bjorn Andersson <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Reviewed-by: Dylan Van Assche <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: sdm845: Enable user LEDs on DB845cBjorn Andersson1-0/+30
The DB845c has 4 "user LEDs", the last one is already supported as it's just wired to a gpio. Now that the LPG binding is in place we can wire up the other 3 LEDs as well. Signed-off-by: Bjorn Andersson <[email protected]> Reviewed-by: Caleb Connolly <[email protected]> Reviewed-by: Dylan Van Assche <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: Add LPG to pm8916, pm8994, pmi8994 and pmi8998Bjorn Andersson4-1/+38
Add PWM/LPG nodes to the PMICs currently supported by the binding. Signed-off-by: Bjorn Andersson <[email protected]> Reviewed-by: Caleb Connolly <[email protected]> Reviewed-by: Dylan Van Assche <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: sm8350: Replace integers with rpmpd definesRobert Foss1-8/+8
Replace &rpmhpd power domain integers with their respective defines in order to improve legibility. Signed-off-by: Robert Foss <[email protected]> Reviewed-by: Konrad Dybcio <[email protected]> Reviewed-by: Vinod Koul <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06arm64: dts: qcom: sm8350: Add DISPCC nodeRobert Foss1-0/+26
Add the dispcc clock-controller DT node for sm8350. Signed-off-by: Robert Foss <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Reviewed-by: Konrad Dybcio <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06Merge branch '[email protected]' into ↵Bjorn Andersson4-2/+129
arm64-for-5.20
2022-07-06arm64: dts: qcom: sm8450: Add description of camera clock controllerVladimir Zapolskiy1-0/+16
The change adds description of Qualcomm SM8450 camera clock controller. Signed-off-by: Vladimir Zapolskiy <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06Merge branch '[email protected]' into ↵Bjorn Andersson2-0/+239
arm64-for-5.20
2022-07-06dt-bindings: clock: add QCOM SM8450 camera clock bindingsVladimir Zapolskiy2-0/+239
The change adds device tree bindings for camera clock controller found on SM8450 SoC. Reviewed-by: Rob Herring <[email protected]> Reviewed-by: Bjorn Andersson <[email protected]> Signed-off-by: Vladimir Zapolskiy <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06dt-bindings: clock: Add Qcom SM8350 DISPCC bindingsJonathan Marek2-2/+5
Add sm8350 DISPCC bindings, which are simply a symlink to the sm8250 bindings. Update the documentation with the new compatible. Signed-off-by: Jonathan Marek <[email protected]> Signed-off-by: Robert Foss <[email protected]> Reviewed-by: Rob Herring <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Reviewed-by: Vinod Koul <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06dt-bindings: clock: Add Qcom SM8350 GPUCC bindingsRobert Foss2-0/+124
Add device tree bindings for graphics clock controller for Qualcomm Technology Inc's SM8350 SoCs. Signed-off-by: Robert Foss <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Reviewed-by: Rob Herring <[email protected]> Signed-off-by: Bjorn Andersson <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06dt-bindings: soc: samsung: exynos-pmu: add reboot-modeKrzysztof Kozlowski1-0/+6
ExynosAutov9 gained a reboot-mode node, so document the property to fix warning: exynosautov9-sadk.dtb: system-controller@10460000: 'reboot-mode' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by: Krzysztof Kozlowski <[email protected]> Reviewed-by: Alim Akhtar <[email protected]> Reviewed-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06dt-bindings: soc: samsung: exynos-pmu: use abolute ref pathsKrzysztof Kozlowski1-2/+2
Preferred coding for referencing other schemas is to use absolute path. Quotes over path are also not needed. Signed-off-by: Krzysztof Kozlowski <[email protected]> Reviewed-by: Alim Akhtar <[email protected]> Reviewed-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06dt-bindings: soc: samsung: exynos-pmu: cleanup assigned clocksKrzysztof Kozlowski1-3/+0
"assigned-clocks" are not needed in the device schema as they come from core schema. Signed-off-by: Krzysztof Kozlowski <[email protected]> Reviewed-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06dt-bindings: samsung: document preferred compatible namingKrzysztof Kozlowski1-0/+40
Compatibles can come in two formats. Either "vendor,ip-soc" or "vendor,soc-ip". Add a DT schema documenting preferred policy and enforcing it for all new compatibles, except few existing patterns. The schema also disallows wild-cards used in SoC compatibles. Signed-off-by: Krzysztof Kozlowski <[email protected]> Reviewed-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-06Merge tag 'juno-updates-5.20' of ↵Arnd Bergmann7-32/+37
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt Armv8 Juno/FVP updates for v5.20 Just a small bunch of miscellaneous updates: addition of missing cache-level property to L2 caches on Juno, whitespace adjustments and removal of erroneous 'mbox-name' and 'panel-dpi' compatible in the device tree nodes. * tag 'juno-updates-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: arm64: dts: juno: Add cache-level property to L2 caches arm64: dts: arm: adjust whitespace around '=' arm64: dts: arm/juno: Drop erroneous 'mbox-name' property arm64: dts: arm/fvp-base-revc: Remove 'panel-dpi' compatible Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnd Bergmann <[email protected]>
2022-07-06Merge tag 'stm32-dt-for-v5.20-1' of ↵Arnd Bergmann26-110/+780
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt STM32 DT for v5.20, round 1 Highlights: ---------- - MCU: -Fix whitespace coding style. No functional changes. - MPU: - General: - Remove specific IPCC wakeup interrupt on STM32MP15. - Enable OPTEE firmware and scmi support (clock/reset) on STM32MP13. It allows to enable RCC clock driver. - Add new pins configurations groups. - DH boards: - Add DHCOR based DRC Compact board. It embeds: 2xETH, 1xCAN, uSD, USB, eMMC and SDIO wifi. - Add ST MIPID02 bindings to AV96 (not enabled by default) - OSD32: - Correct vcc-supply for eeprom. - fix missing internally connected voltage regulator (ldo3 supplied by vdd_ddr). * tag 'stm32-dt-for-v5.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (25 commits) ARM: dts: stm32: Add ST MIPID02 bindings to AV96 ARM: dts: stm32: Add alternate pinmux for RCC pin ARM: dts: stm32: Add alternate pinmux for DCMI pins ARM: dts: stm32: Add DHCOR based DRC Compact board ARM: dts: stm32: Add alternate pinmux for UART5 pins ARM: dts: stm32: Add alternate pinmux for UART4 pins ARM: dts: stm32: Add alternate pinmux for UART3 pins ARM: dts: stm32: Add alternate pinmux for SPI2 pins ARM: dts: stm32: Add alternate pinmux for CAN1 pins dt-bindings: arm: stm32: Add compatible string for DH electronics DHCOR DRC Compact ARM: dts: stm32: Fix SPI2 pinmux pin comments on stm32mp15 ARM: dts: stm32: add optee reserved memory on stm32mp135f-dk ARM: dts: stm32: add RCC on STM32MP13x SoC family ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP13 dt-bindings: rcc: stm32: select the "secure" path for stm32mp13 ARM: dts: stm32: correct vcc-supply for eeprom on stm32mp15xx-osd32 ARM: dts: stm32: fix missing internally connected voltage regulator for OSD32MP1 ARM: dts: stm32: adjust whitespace around '=' on MCU boards ARM: dts: stm32: Move DHCOR BUCK3 VDD 2V9 adjustment to 1V8 DTSI ARM: dts: stm32: remove the IPCC "wakeup" IRQ on stm32mp151 ... Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnd Bergmann <[email protected]>
2022-07-06Merge tag 'at91-dt-5.20' of ↵Arnd Bergmann19-37/+69
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt AT91 DT for v5.20 It contains: - compilation warning fixes for SAMA5D2 - updates for all AT91 device tree to use generic name for reset controller - reset controller node for SAMA7G5 - MCAN1 and UDPHS nodes for LAN966 SoCs - Flexcom3 bindings were updated for lan966x-pcb8291.dts board to cope with reality * tag 'at91-dt-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: ARM: dts: lan966x: Add UDPHS support dt-bindings: usb: atmel: Add Microchip LAN9662 compatible string ARM: dts: lan966x: Cleanup flexcom3 usart pinctrl settings. ARM: dts: lan966x: Add mcan1 node. ARM: dts: at91: sama7g5: add reset-controller node ARM: dts: at91: use generic name for reset controller ARM: dts: at91: sama5d2: fix compilation warning ARM: dts: at91: sama5d2: fix compilation warning Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Arnd Bergmann <[email protected]>
2022-07-06Merge tag 'ux500-dts-v5.20' of ↵Arnd Bergmann4-11/+6
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt Ux500 DTS updates for the v5.20 kernel: - Fix orientation matrices on a few U8500 mobile phones. - Drop unused i2c power supply handled by the power domain. * tag 'ux500-dts-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik: ARM: dts: ux500: Drop unused i2c power domain supply ARM: dts: ux500: Fix Gavini accelerometer mounting matrix ARM: dts: ux500: Fix Codina accelerometer mounting matrix ARM: dts: ux500: Fix Janice accelerometer mounting matrix Link: https://lore.kernel.org/r/CACRpkdY1MG=HG+tOCmD1_LEAStV1-ycCLkwShMRD4R=4jGDYHQ@mail.gmail.com Signed-off-by: Arnd Bergmann <[email protected]>
2022-07-06Merge tag 'v5.20-rockchip-dts32-1' of ↵Arnd Bergmann23-44/+60
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt NFC flash node on rk3066a-mk808 and some dts styling fixes (alignment and node names). * tag 'v5.20-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: ARM: dts: rockchip: correct gpio-keys properties on rk3288-tinker ARM: dts: rockchip: align gpio-key node names with dtschema ARM: dts: rockchip: adjust whitespace around '=' ARM: dts: rockchip: enable nfc node in rk3066a-mk808.dts Link: https://lore.kernel.org/r/14795241.VsHLxoZxqI@phil Signed-off-by: Arnd Bergmann <[email protected]>
2022-07-06Merge tag 'v5.20-rockchip-dts64-1' of ↵Arnd Bergmann37-51/+859
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt New board the Radxa Rock Pi S, enablement of graphics support and hdmi-audio on rk356x in general plus necessary board-specific changes on Rock-3A, Quartz64-A, rk3568-evb, BPI-R2-Pro. A number of additional peripherals on BPI-R2-Pro (gpu, thermal, rtc) and PCIe2x1 support on rk3568 and enablement on Quart64-A as well as a number of additional peripherals to this board (sfc node, sdr-104 support, fan). And finally touch panel support for rockpro64 and some misc dt cleanups (node names for dtschema and styling). * tag 'v5.20-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (27 commits) arm64: dts: rockchip: enable hdmi tx audio on rock-3a arm64: dts: rockchip: enable hdmi tx audio on rk3568-evb1-v10 arm64: dts: rockchip: align gpio-key node names with dtschema arm64: dts: rockchip: rock-pi-s add more peripherals arm64: dts: rockchip: add ROCK Pi S DTS support dt-bindings: arm: rockchip: Add Radxa ROCK Pi S arm64: dts: rockchip: Add missing space around regulator-name on rk3368-orion-r68 arm64: dts: rockchip: enable the gpu on BPI-R2-Pro arm64: dts: rockchip: configure thermal shutdown for BPI-R2-Pro arm64: dts: rockchip: Enable HDMI audio on BPI R2 Pro arm64: dts: rockchip: enable vop2 and hdmi tx on BPI-R2-Pro arm64: dts: rockchip: set display regulators to always-on on BPI-R2-Pro arm64: dts: rockchip: add RTC to BPI-R2 Pro arm64: dts: rockchip: Enable HDMI audio on Quartz64 A arm64: dts: rockchip: Add HDMI audio nodes to rk356x arm64: dts: rockchip: adjust whitespace around '=' arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a arm64: dts: rockchip: enable vop2 and hdmi tx on quartz64a arm64: dts: rockchip: rk3568-evb: Enable VOP2 and hdmi arm64: dts: rockchip: rk356x: Add HDMI nodes ... Link: https://lore.kernel.org/r/40088956.J2Yia2DhmK@phil Signed-off-by: Arnd Bergmann <[email protected]>
2022-07-05dt-bindings: usb: generic-ohci: Add Allwinner D1 compatibleSamuel Holland1-0/+1
The Allwinner D1 contains USB controllers which claim to be compatible with the OHCI specification version 1.0a. Signed-off-by: Samuel Holland <[email protected]> Acked-by: Jernej Skrabec <[email protected]> Signed-off-by: Jernej Skrabec <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2022-07-05dt-bindings: usb: generic-ehci: Add Allwinner D1 compatibleSamuel Holland1-0/+1
The Allwinner D1 contains USB controllers which claim to be compatible with the EHCI specification version 1.0. Signed-off-by: Samuel Holland <[email protected]> Acked-by: Jernej Skrabec <[email protected]> Signed-off-by: Jernej Skrabec <[email protected]> Link: https://lore.kernel.org/r/[email protected]
Powered by cgit, Gruvboxed by Blaster4385.