| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The kernel gained a new interface for drivers to use to combine tail
bump (doorbell) and BQL updates, attempt to use those new interfaces.
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The driver had comments to the effect of: This flag should be set before
calling this function. While reviewing code it was found that there were
several violations of this policy, which could introduce hard to find
bugs or races.
Fix the violations of the "VSI DOWN state must be set before calling
ice_down" and make checking the state into code with a WARN_ON.
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The kernel provides some prefetch mechanisms to speed up commonly
cold cache line accesses during receive processing. Since these are
software structures it helps to have these strategically placed
prefetches.
Be careful to call BQL prefetch complete only for non XDP queues.
Co-developed-by: Piotr Raczynski <[email protected]>
Signed-off-by: Piotr Raczynski <[email protected]>
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Use the netif_tx_* API from netdevice.h which has simpler parameters.
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice hardware contains an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
In practical terms, activating the firmware does not always require a
full system reboot. In many cases it is possible to activate the EMP
firmware immediately. There are a couple of different scenarios to
cover.
* The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
* PCI configuration changes are only reloaded after a cold PCIe reset.
Unfortunately there is no generic way to trigger this for a PCIe
device without a system reboot.
When performing a flash update, firmware is capable of responding with
some information about the specific update requirements.
The driver updates the flash by programming a secondary inactive bank
with the contents of the new image, and then issuing a command to
request to switch the active bank starting from the next load.
The response to the final command for updating the inactive NVM flash
bank includes an indication of the minimum reset required to fully
update the device. This can be one of the following:
* A full power on is required
* A cold PCIe reset is required
* An EMP reset is required
The response to the command to switch flash banks includes an indication
of whether or not the firmware will allow an EMP reset request.
For most updates, an EMP reset is sufficient to load the new EMP
firmware without issues. In some cases, this reset is not sufficient
because the PCI configuration space has changed. When this could cause
incompatibility with the new EMP image, the firmware is capable of
rejecting the EMP reset request.
Add logic to ice_fw_update.c to handle the response data flash update
AdminQ commands.
For the reset level, issue a devlink status notification informing the
user of how to complete the update with a simple suggestion like
"Activate new firmware by rebooting the system".
Cache the status of whether or not firmware will restrict the EMP reset
for use in implementing devlink reload.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
For the .reload_down handler, we will issue a request for the EMP reset
using the appropriate firmware AdminQ command. If we know that the
firmware will not allow an EMP reset, simply exit with a suitable
netlink extended ACK message indicating that the EMP reset is not
available.
For the .reload_up handler, simply wait until the driver has finished
resetting. Logic to handle processing of an EMP reset already exists in
the driver as part of its reset and rebuild flows.
Implement support for the devlink reload interface with the
"fw_activate" action. This allows userspace to request activation of
firmware without a reboot.
Note that support for indicating the required reset and EMP reset
restriction is not supported on old versions of firmware. The driver can
determine if the two features are supported by checking the device
capabilities report. I confirmed support has existed since at least
version 5.5.2 as reported by the 'fw.mgmt' version. Support to issue the
EMP reset request has existed in all version of the EMP firmware for the
ice hardware.
Check the device capabilities report to determine whether or not the
indications are reported by the running firmware. If the reset
requirement indication is not supported, always assume a full power on
is necessary. If the reset restriction capability is not supported,
always assume the EMP reset is available.
Users can verify if the EMP reset has activated the firmware by using
the devlink info report to check that the 'running' firmware version has
updated. For example a user might do the following:
# Check current version
$ devlink dev info
# Update the device
$ devlink dev flash pci/0000:af:00.0 file firmware.bin
# Confirm stored version updated
$ devlink dev info
# Reload to activate new firmware
$ devlink dev reload pci/0000:af:00.0 action fw_activate
# Confirm running version updated
$ devlink dev info
Finally, this change does *not* implement basic driver-only reload
support. I did look into trying to do this. However, it requires
significant refactor of how the ice driver probes and loads everything.
The ice driver probe and allocation flows were not designed with such
a reload in mind. Refactoring the flow to support this is beyond the
scope of this change.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
During probe and device reset, the ice driver reads some data from the
NVM image as part of ice_init_nvm. Part of this data includes a section
of the Option ROM which contains version information.
The function ice_get_orom_civd_data is used to locate the '$CIV' data
section of the Option ROM.
Timing of ice_probe and ice_rebuild indicate that the
ice_get_orom_civd_data function takes about 10 seconds to finish
executing.
The function locates the section by scanning the Option ROM every 512
bytes. This requires a significant number of NVM read accesses, since
the Option ROM bank is 500KB. In the worst case it would take about 1000
reads. Worse, all PFs serialize this operation during reload because of
acquiring the NVM semaphore.
The CIVD section is located at the end of the Option ROM image data.
Unfortunately, the driver has no easy method to determine the offset
manually. Practical experiments have shown that the data could be at
a variety of locations, so simply reversing the scanning order is not
sufficient to reduce the overall read time.
Instead, copy the entire contents of the Option ROM into memory. This
allows reading the data using 4Kb pages instead of 512 bytes at a time.
This reduces the total number of firmware commands by a factor of 8. In
addition, reading the whole section together at once allows better
indication to firmware of when we're "done".
Re-write ice_get_orom_civd_data to allocate virtual memory to store the
Option ROM data. Copy the entire OptionROM contents at once using
ice_read_flash_module. Finally, use this memory copy to scan for the
'$CIV' section.
This change significantly reduces the time to read the Option ROM CIVD
section from ~10 seconds down to ~1 second. This has a significant
impact on the total time to complete a driver rebuild or probe.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice_devlink_flash_update function performs a few upfront checks and
then calls ice_flash_pldm_image.
Most if these checks make more sense in the context of code within
ice_flash_pldm_image. Merge ice_devlink_flash_update and
ice_flash_pldm_image into one function, placing it in ice_fw_update.c
Since this is still the entry point for devlink, call the function
ice_devlink_flash_update instead of ice_flash_pldm_image. This leaves a
single function which handles the devlink parameters and then initiates
a PLDM update.
With this change, the ice_devlink_flash_update function in
ice_fw_update.c becomes the main entry point for flash update. It
elimintes some unnecessary boiler plate code between the two previous
functions. The ultimate motivation for this is that it eases supporting
a dry run with the PLDM library in a future change.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice_devlink_flash_update function performs a few checks and then
calls ice_flash_pldm_image. One of these checks is to call
ice_check_for_pending_update. This function checks if the device has
a pending update, and cancels it if so. This is necessary to allow
a new flash update to proceed.
We want to refactor the ice code to eliminate ice_devlink_flash_update,
moving its checks into ice_flash_pldm_image.
To do this, ice_check_for_pending_update will become static, and only
called by ice_flash_pldm_image. To make this change easier to review,
first just move the function up within the ice_fw_update.c file.
While at it, note that the function has a misleading name. Its primary
action is to cancel a pending update. Using the verb "check" does not
imply this. Rename it to ice_cancel_pending_update.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
We have a region for reading the contents of the NVM flash as
a snapshot. This region does not allow reading the Shadow RAM, as it
always passes the FLASH_ONLY bit to the low level firmware interface.
Add a separate shadow-ram region which will allow snapshot of the
current contents of the Shadow RAM. This data is built from the NVM
contents but is distinct as the device builds up the Shadow RAM during
initialization, so being able to snapshot its contents can be useful
when attempting to debug flash related issues.
Fix the comment description of the nvm-flash region which incorrectly
stated that it filled the shadow-ram region, and add a comment
explaining that the nvm-flash region does not actually read the Shadow
RAM.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The driver has to check if it does not accidentally put the timestamp in
the SKB before previous timestamp gets overwritten.
Timestamp values in the PHY are read only and do not get cleared except
at hardware reset or when a new timestamp value is captured.
The cached_tstamp field is used to detect the case where a new timestamp
has not yet been captured, ensuring that we avoid sending stale
timestamp data to the stack.
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Karol Kolacinski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Change the division in ice_ptp_adjfine from div_u64 to div64_u64.
div_u64 is used when the divisor is 32 bit but in this case incval is
64 bit and it caused incorrect calculations and incval adjustments.
Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Karol Kolacinski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Remove the unused define ICE_FLOW_SEG_HDRS_L2_MASK.
Reported-by: Jesse Brandeburg <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
Acked-by: Paul Menzel <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
The "bitmap" variable is already an unsigned long so there is no need
for this cast.
Signed-off-by: Dan Carpenter <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
As all functions now return standard error codes, propagate the values
being returned instead of converting them to generic values.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
ice_status previously had a variable to contain these values where other
error codes had a variable as well. With ice_status now being an int,
there is no need for two variables to hold error values. In cases where
this occurs, remove one of the excess variables and use a single one.
Some initialization of variables are no longer needed and have been
removed.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
Clean up code after changing ice_status to int. Rearrange to fix reverse
Christmas tree and pull lines up where applicable.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
Replace uses of ice_status to, as equivalent as possible, error codes.
Remove enum ice_status and its helper conversion function as they are no
longer needed.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
To prepare for removal of ice_status, change the variables from
ice_status to int. This eases the transition when values are changed to
return standard int error codes over enum ice_status.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
Remove the ice_stat_str() function which prints the string
representation of the ice_status error code. With upcoming changes
moving away from ice_status, there will be no need for this function.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
Before this change, final state of the DDP pkg load process was
dependent on many variables such as: ice_status, pkg version,
ice_aq_err. The last one had be stored in hw->pkg_dwnld_status.
It was impossible to conclude this state just from ice_status, that's
why logging process of DDP pkg load in the caller was a little bit
complicated.
With this patch new status enum is introduced - ice_ddp_state.
It covers all the possible final states of the loading process.
What's tricky for ice_ddp_state is that not only
ICE_DDP_PKG_SUCCESS(=0) means that load was successful. Actually
three states mean that:
- ICE_DDP_PKG_SUCCESS
- ICE_DDP_PKG_SAME_VERSION_ALREADY_LOADED
- ICE_DDP_PKG_COMPATIBLE_ALREADY_LOADED
ice_is_init_pkg_successful can tell that information.
One ddp_state should not be used outside of ice_init_pkg which is
ICE_DDP_PKG_ALREADY_LOADED. It is more generic, it is used in
ice_dwnld_cfg_bufs to see if pkg is already loaded. At this point
we can't use one of the specific one (SAME_VERSION, COMPATIBLE,
NOT_SUPPORTED) because we don't have information on the package
currently loaded in HW (we are before calling ice_get_pkg_info).
We can get rid of hw->pkg_dwnld_status because we are immediately
mapping aq errors to ice_ddp_state in ice_dwnld_cfg_bufs.
Other errors like ICE_ERR_NO_MEMORY, ICE_ERR_PARAM are mapped the
generic ICE_DDP_PKG_ERR.
Suggested-by: Jacob Keller <[email protected]>
Signed-off-by: Wojciech Drewek <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Some of the promiscuous mode functions take a boolean to indicate
set/clear, which affects readability. Refactor and provide an
interface for the promiscuous mode code with explicit set and clear
promiscuous mode operations.
Signed-off-by: Brett Creeley <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Since the capability of a PTYPE within a specific package could be
negotiated by checking the HW bit map, it means that there's no need
to maintain a different PTYPE list for each type of the package when
parsing PTYPE. So refactor the PTYPE validating mechanism.
Signed-off-by: Jeff Guo <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Scan the 'Marker Ptype TCAM' section to retrieve the Rx parser PTYPE
enable information from the current package.
Signed-off-by: Haiyue Wang <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <[email protected]>
Signed-off-by: Hangbin Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
zero_copy_allocator has been removed back when Bjorn Topel introduced
xsk_buff_pool. Remove references to it that were dangling in the tree.
Signed-off-by: Maciej Fijalkowski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Magnus Karlsson <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.
Let's additionally include the program name and id, and the relevant
device name.
If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.
Signed-off-by: Paolo Abeni <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Toke Høiland-Jørgensen <[email protected]>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
|
|
The watchdog task incorrectly changes the state to __IAVF_RESETTING,
instead of letting the reset task take care of that. This was already
resolved by commit 22c8fd71d3a5 ("iavf: do not override the adapter
state in the watchdog task") but the problem was reintroduced by the
recent code refactoring in commit 45eebd62999d ("iavf: Refactor iavf
state machine tracking").
Fixes: 45eebd62999d ("iavf: Refactor iavf state machine tracking")
Signed-off-by: Stefan Assmann <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
This code was re-organized and there some unlocks missing now.
Fixes: 898ef1cb1cb2 ("iavf: Combine init and watchdog state machines")
Signed-off-by: Dan Carpenter <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The driver uses irq_set_affinity_hint() to update the affinity_hint mask
that is consumed by the userspace to distribute the interrupts. However,
under the hood irq_set_affinity_hint() also applies the provided cpumask
(if not NULL) as the affinity for the given interrupt which is an
undocumented side effect.
To remove this side effect irq_set_affinity_hint() has been marked
as deprecated and new interfaces have been introduced. Hence, replace the
irq_set_affinity_hint() with the new interface irq_update_affinity_hint()
that only updates the affinity_hint pointer.
Signed-off-by: Nitesh Narayan Lal <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: Jesse Brandeburg <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The driver uses irq_set_affinity_hint() for two purposes:
- To set the affinity_hint which is consumed by the userspace for
distributing the interrupts
- To apply an affinity that it provides for the i40e interrupts
The latter is done to ensure that all the interrupts are evenly spread
across all available CPUs. However, since commit a0c9259dc4e1 ("irq/matrix:
Spread interrupts on allocation") the spreading of interrupts is
dynamically performed at the time of allocation. Hence, there is no need
for the drivers to enforce their own affinity for the spreading of
interrupts.
Also, irq_set_affinity_hint() applying the provided cpumask as an affinity
for the interrupt is an undocumented side effect. To remove this side
effect irq_set_affinity_hint() has been marked as deprecated and new
interfaces have been introduced. Hence, replace the irq_set_affinity_hint()
with the new interface irq_update_affinity_hint() that only sets the
pointer for the affinity_hint.
Signed-off-by: Nitesh Narayan Lal <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: Jesse Brandeburg <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The driver uses irq_set_affinity_hint() for two purposes:
- To set the affinity_hint which is consumed by the userspace for
distributing the interrupts
- To apply an affinity that it provides for the iavf interrupts
The latter is done to ensure that all the interrupts are evenly spread
across all available CPUs. However, since commit a0c9259dc4e1 ("irq/matrix:
Spread interrupts on allocation") the spreading of interrupts is
dynamically performed at the time of allocation. Hence, there is no need
for the drivers to enforce their own affinity for the spreading of
interrupts.
Also, irq_set_affinity_hint() applying the provided cpumask as an affinity
for the interrupt is an undocumented side effect. To remove this side
effect irq_set_affinity_hint() has been marked as deprecated and new
interfaces have been introduced. Hence, replace the irq_set_affinity_hint()
with the new interface irq_update_affinity_hint() that only sets the
pointer for the affinity_hint.
Signed-off-by: Nitesh Narayan Lal <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: Jesse Brandeburg <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-12-08
Yahui adds re-initialization of Flow Director for VF reset.
Paul restores interrupts when enabling VFs.
Dave re-adds bandwidth check for DCBNL and moves DSCP mode check
earlier in the function.
Jesse prevents reporting of dropped packets that occur during
initialization and fixes reporting of statistics which could occur with
frequent reads.
Michal corrects setting of protocol type for UDP header and fixes lack
of differentiation when adding filters for tunnels.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: safer stats processing
ice: fix adding different tunnels
ice: fix choosing UDP header type
ice: ignore dropped packets during init
ice: Fix problems with DSCP QoS implementation
ice: rearm other interrupt cause register after enabling VFs
ice: fix FDIR init missing when reset VF
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The driver was zeroing live stats that could be fetched by
ndo_get_stats64 at any time. This could result in inconsistent
statistics, and the telltale sign was when reading stats frequently from
/proc/net/dev, the stats would go backwards.
Fix by collecting stats into a local, and delaying when we write to the
structure so it's not incremental.
Fixes: fcea6f3da546 ("ice: Add stats and ethtool support")
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Adding filters with the same values inside for VXLAN and Geneve causes HW
error, because it looks exactly the same. To choose between different
type of tunnels new recipe is needed. Add storing tunnel types in
creating recipes function and start checking it in finding function.
Change getting open tunnels function to return port on correct tunnel
type. This is needed to copy correct port to dummy packet.
Block user from adding enc_dst_port via tc flower, because VXLAN and
Geneve filters can be created only with destination port which was
previously opened.
Fixes: 8b032a55c1bd5 ("ice: low level support for tunnels")
Signed-off-by: Michal Swiatkowski <[email protected]>
Tested-by: Sandeep Penigalapati <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In tunnels packet there can be two UDP headers:
- outer which for hw should be mark as ICE_UDP_OF
- inner which for hw should be mark as ICE_UDP_ILOS or as ICE_TCP_IL if
inner header is of TCP type
In none tunnels packet header can be:
- UDP, which for hw should be mark as ICE_UDP_ILOS
- TCP, which for hw should be mark as ICE_TCP_IL
Change incorrect ICE_UDP_OF for none tunnel packets to ICE_UDP_ILOS.
ICE_UDP_OF is incorrect for none tunnel packets and setting it leads to
error from hw while adding this kind of recipe.
In summary, for tunnel outer port type should always be set to
ICE_UDP_OF, for none tunnel outer and tunnel inner it should always be
set to ICE_UDP_ILOS.
Fixes: 9e300987d4a8 ("ice: VXLAN and Geneve TC support")
Signed-off-by: Michal Swiatkowski <[email protected]>
Tested-by: Sandeep Penigalapati <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
If the hardware is constantly receiving unicast or broadcast packets
during driver load, the device previously counted many GLV_RDPC (VSI
dropped packets) events during init. This causes confusing dropped
packet statistics during driver load. The dropped packets counter
incrementing does stop once the driver finishes loading.
Avoid this problem by baselining our statistics at the end of driver
open instead of the end of probe.
Fixes: cdedef59deb0 ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The patch that implemented DSCP QoS implementation removed a
bandwidth check that was used to check for a specific condition
caused by some corner cases. This check should not of been
removed.
The same patch also added a check for when the DCBx state could
be changed in relation to DSCP, but the check was erroneously
added nested in a check for CEE mode, which made the check useless.
Fix these problems by re-adding the bandwidth check and relocating
the DSCP mode check earlier in the function that changes DCBx state
in the driver.
Fixes: 2a87bd73e50d ("ice: Add DSCP support")
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Dave Ertman <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The other interrupt cause register (OICR), global interrupt 0, is
disabled when enabling VFs to prevent handling VFLR. If the OICR is
not rearmed then the VF cannot communicate with the PF.
Rearm the OICR after enabling VFs.
Fixes: 916c7fdf5e93 ("ice: Separate VF VSI initialization/creation from reset flow")
Signed-off-by: Paul Greenwalt <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When VF is being reset, ice_reset_vf() will be called and FDIR
resource should be released and initialized again.
Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Yahui Cao <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When trying to dump VFs VSI RX/TX descriptors
using debugfs there was a crash
due to NULL pointer dereference in i40e_dbg_dump_desc.
Added a check to i40e_dbg_dump_desc that checks if
VSI type is correct for dumping RX/TX descriptors.
Fixes: 02e9c290814c ("i40e: debugfs interface")
Signed-off-by: Sylwester Dziedziuch <[email protected]>
Signed-off-by: Norbert Zulinski <[email protected]>
Signed-off-by: Mateusz Palczewski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
After setting pre-set combined to 16 queues and reserving 16 queues by
tc qdisc, pre-set maximum combined queues returned to default value
after VF reset being 4 and this generated errors during removing tc.
Fixed by removing clear num_req_queues before reset VF.
Fixes: e284fc280473 (i40e: Add and delete cloud filter)
Signed-off-by: Grzegorz Szczurek <[email protected]>
Signed-off-by: Mateusz Palczewski <[email protected]>
Tested-by: Bindushree P <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Fix failed operation code appearing if handling messages from VF.
Implemented by waiting for VF appropriate state if request starts
handle while VF reset.
Without this patch the message handling request while VF is in
a reset state ends with error -5 (I40E_ERR_PARAM).
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <[email protected]>
Signed-off-by: Karen Sornek <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
iavf_set_ringparams doesn't communicate to the user that
1. The user requested descriptor count is out of range. Instead it
just quietly sets descriptors to the "clamped" value and calls it
done. This makes it look an invalid value was successfully set as
the descriptor count when this isn't actually true.
2. The user provided descriptor count needs to be inflated for alignment
reasons.
This behavior is confusing. The ice driver has already addressed this
by rejecting invalid values for descriptor count and
messaging for alignment adjustments.
Do the same thing here by adding the error and info messages.
Fixes: fbb7ddfef253 ("i40evf: core ethtool functionality")
Signed-off-by: Anirudh Venkataramanan <[email protected]>
Signed-off-by: Michal Maloszewski <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
If the PF experiences an FLR, the VF's MSI and MSI-X configuration will
be conveniently and silently removed in the process. When this happens,
reset recovery will appear to complete normally but no traffic will
pass. The netdev watchdog will helpfully notify everyone of this issue.
To prevent such public embarrassment, restore MSI configuration at every
reset. For normal resets, this will do no harm, but for VF resets
resulting from a PF FLR, this will keep the VF working.
Fixes: 5eae00c57f5e ("i40evf: main driver core")
Signed-off-by: Mitch Williams <[email protected]>
Tested-by: George Kuruvinakunnel <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-11-30
This series contains updates to iavf driver only.
Patryk adds a debug message when MTU is changed.
Grzegorz adds messaging when transitioning in and out of multicast
promiscuous mode.
Jake returns correct error codes for iavf_parse_cls_flower().
Jedrzej adds messaging for when the driver is removed and refactors
struct usage to take less memory. He also adjusts ethtool statistics to
only display information on active queues.
Tony allows for user to specify the RSS hash.
Karen resolves some static analysis warnings, corrects format specifiers,
and rewords a message to come across as informational.
v2:
- Dropped patch 1 (for net) and 5
- Change MTU message from info to debug
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-11-30
This series contains updates to ice driver only.
Shiraz corrects assignment of boolean variable and removes an unused
enum.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Driver provided too many lines as an output to ethtool -S command.
Return actual length of string set of ethtool stats. Instead of predefined
maximal value use the actual value on netdev, iterate over active queues.
Without this patch, ethtool -S report would produce additional
erroneous lines of queues that are not configured.
Signed-off-by: Witold Fijalkowski <[email protected]>
Signed-off-by: Przemyslaw Patynowski <[email protected]>
Signed-off-by: Mateusz Palczewski <[email protected]>
Signed-off-by: Jedrzej Jagielski <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Change format to match variable type that is used in string.
Use %u format for unsigned variable and %d format for signed variable
to remove static analysis warnings.
Signed-off-by: Michal Swiatkowski <[email protected]>
Signed-off-by: Karen Sornek <[email protected]>
Tested-by: George Kuruvinakunnel <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|