aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel
AgeCommit message (Collapse)AuthorFilesLines
2024-11-12Revert "igb: Disable threaded IRQ for igb_msix_other"Wander Lairson Costa1-1/+1
This reverts commit 338c4d3902feb5be49bfda530a72c7ab860e2c9f. Sebastian noticed the ISR indirectly acquires spin_locks, which are sleeping locks under PREEMPT_RT, which leads to kernel splats. Fixes: 338c4d3902feb ("igb: Disable threaded IRQ for igb_msix_other") Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Wander Lairson Costa <wander@redhat.com> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Link: https://patch.msgid.link/20241106111427.7272-1-wander@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-04e1000e: Remove Meteor Lake SMBUS workaroundsVitaly Lifshits1-13/+4
This is a partial revert to commit 76a0a3f9cc2f ("e1000e: fix force smbus during suspend flow"). That commit fixed a sporadic PHY access issue but introduced a regression in runtime suspend flows. The original issue on Meteor Lake systems was rare in terms of the reproduction rate and the number of the systems affected. After the integration of commit 0a6ad4d9e169 ("e1000e: avoid failing the system during pm_suspend"), PHY access loss can no longer cause a system-level suspend failure. As it only occurs when the LAN cable is disconnected, and is recovered during system resume flow. Therefore, its functional impact is low, and the priority is given to stabilizing runtime suspend. Fixes: 76a0a3f9cc2f ("e1000e: fix force smbus during suspend flow") Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Avigail Dahan <avigailx.dahan@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-11-04i40e: fix race condition by adding filter's intermediate sync stateAleksandr Loktionov3-2/+12
Fix a race condition in the i40e driver that leads to MAC/VLAN filters becoming corrupted and leaking. Address the issue that occurs under heavy load when multiple threads are concurrently modifying MAC/VLAN filters by setting mac and port VLAN. 1. Thread T0 allocates a filter in i40e_add_filter() within i40e_ndo_set_vf_port_vlan(). 2. Thread T1 concurrently frees the filter in __i40e_del_filter() within i40e_ndo_set_vf_mac(). 3. Subsequently, i40e_service_task() calls i40e_sync_vsi_filters(), which refers to the already freed filter memory, causing corruption. Reproduction steps: 1. Spawn multiple VFs. 2. Apply a concurrent heavy load by running parallel operations to change MAC addresses on the VFs and change port VLANs on the host. 3. Observe errors in dmesg: "Error I40E_AQ_RC_ENOSPC adding RX filters on VF XX, please set promiscuous on manually for VF XX". Exact code for stable reproduction Intel can't open-source now. The fix involves implementing a new intermediate filter state, I40E_FILTER_NEW_SYNC, for the time when a filter is on a tmp_add_list. These filters cannot be deleted from the hash list directly but must be removed using the full process. Fixes: 278e7d0b9d68 ("i40e: store MAC/VLAN filters in a hash with the MAC Address as key") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Tested-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-11-04idpf: fix idpf_vc_core_init error pathPavan Kumar Linga2-1/+1
In an event where the platform running the device control plane is rebooted, reset is detected on the driver. It releases all the resources and waits for the reset to complete. Once the reset is done, it tries to build the resources back. At this time if the device control plane is not yet started, then the driver timeouts on the virtchnl message and retries to establish the mailbox again. In the retry flow, mailbox is deinitialized but the mailbox workqueue is still alive and polling for the mailbox message. This results in accessing the released control queue leading to null-ptr-deref. Fix it by unrolling the work queue cancellation and mailbox deinitialization in the reverse order which they got initialized. Fixes: 4930fbf419a7 ("idpf: add core init and interrupt request") Fixes: 34c21fa894a1 ("idpf: implement virtchnl transaction manager") Cc: stable@vger.kernel.org # 6.9+ Reviewed-by: Tarun K Singh <tarun.k.singh@intel.com> Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-11-04idpf: avoid vport access in idpf_get_link_ksettingsPavan Kumar Linga4-13/+8
When the device control plane is removed or the platform running device control plane is rebooted, a reset is detected on the driver. On driver reset, it releases the resources and waits for the reset to complete. If the reset fails, it takes the error path and releases the vport lock. At this time if the monitoring tools tries to access link settings, it call traces for accessing released vport pointer. To avoid it, move link_speed_mbps to netdev_priv structure which removes the dependency on vport pointer and the vport lock in idpf_get_link_ksettings. Also use netif_carrier_ok() to check the link status and adjust the offsetof to use link_up instead of link_speed_mbps. Fixes: 02cbfba1add5 ("idpf: add ethtool callbacks") Cc: stable@vger.kernel.org # 6.7+ Reviewed-by: Tarun K Singh <tarun.k.singh@intel.com> Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-11-04ice: change q_index variable type to s16 to store -1 valueMateusz Polchlopek2-2/+5
Fix Flow Director not allowing to re-map traffic to 0th queue when action is configured to drop (and vice versa). The current implementation of ethtool callback in the ice driver forbids change Flow Director action from 0 to -1 and from -1 to 0 with an error, e.g: # ethtool -U eth2 flow-type tcp4 src-ip 1.1.1.1 loc 1 action 0 # ethtool -U eth2 flow-type tcp4 src-ip 1.1.1.1 loc 1 action -1 rmgr: Cannot insert RX class rule: Invalid argument We set the value of `u16 q_index = 0` at the beginning of the function ice_set_fdir_input_set(). In case of "drop traffic" action (which is equal to -1 in ethtool) we store the 0 value. Later, when want to change traffic rule to redirect to queue with index 0 it returns an error caused by duplicate found. Fix this behaviour by change of the type of field `q_index` from u16 to s16 in `struct ice_fdir_fltr`. This allows to store -1 in the field in case of "drop traffic" action. What is more, change the variable type in the function ice_set_fdir_input_set() and assign at the beginning the new `#define ICE_FDIR_NO_QUEUE_IDX` which is -1. Later, if the action is set to another value (point specific queue index) the variable value is overwritten in the function. Fixes: cac2a27cd9ab ("ice: Support IPv4 Flow Director filters") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-11-04ice: Fix use after free during unload with ports in bridgeMarcin Szycik1-1/+2
Unloading the ice driver while switchdev port representors are added to a bridge can lead to kernel panic. Reproducer: modprobe ice devlink dev eswitch set $PF1_PCI mode switchdev ip link add $BR type bridge ip link set $BR up echo 2 > /sys/class/net/$PF1/device/sriov_numvfs sleep 2 ip link set $PF1 master $BR ip link set $VF1_PR master $BR ip link set $VF2_PR master $BR ip link set $PF1 up ip link set $VF1_PR up ip link set $VF2_PR up ip link set $VF1 up rmmod irdma ice When unloading the driver, ice_eswitch_detach() is eventually called as part of VF freeing. First, it removes a port representor from xarray, then unregister_netdev() is called (via repr->ops.rem()), finally representor is deallocated. The problem comes from the bridge doing its own deinit at the same time. unregister_netdev() triggers a notifier chain, resulting in ice_eswitch_br_port_deinit() being called. It should set repr->br_port = NULL, but this does not happen since repr has already been removed from xarray and is not found. Regardless, it finishes up deallocating br_port. At this point, repr is still not freed and an fdb event can happen, in which ice_eswitch_br_fdb_event_work() takes repr->br_port and tries to use it, which causes a panic (use after free). Note that this only happens with 2 or more port representors added to the bridge, since with only one representor port, the bridge deinit is slightly different (ice_eswitch_br_port_deinit() is called via ice_eswitch_br_ports_flush(), not ice_eswitch_br_port_unlink()). Trace: Oops: general protection fault, probably for non-canonical address 0xf129010fd1a93284: 0000 [#1] PREEMPT SMP KASAN NOPTI KASAN: maybe wild-memory-access in range [0x8948287e8d499420-0x8948287e8d499427] (...) Workqueue: ice_bridge_wq ice_eswitch_br_fdb_event_work [ice] RIP: 0010:__rht_bucket_nested+0xb4/0x180 (...) Call Trace: (...) ice_eswitch_br_fdb_find+0x3fa/0x550 [ice] ? __pfx_ice_eswitch_br_fdb_find+0x10/0x10 [ice] ice_eswitch_br_fdb_event_work+0x2de/0x1e60 [ice] ? __schedule+0xf60/0x5210 ? mutex_lock+0x91/0xe0 ? __pfx_ice_eswitch_br_fdb_event_work+0x10/0x10 [ice] ? ice_eswitch_br_update_work+0x1f4/0x310 [ice] (...) A workaround is available: brctl setageing $BR 0, which stops the bridge from adding fdb entries altogether. Change the order of operations in ice_eswitch_detach(): move the call to unregister_netdev() before removing repr from xarray. This way repr->br_port will be correctly set to NULL in ice_eswitch_br_port_deinit(), preventing a panic. Fixes: fff292b47ac1 ("ice: add VF representors one by one") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-29ice: fix crash on probe for DPLL enabled E810 LOMArkadiusz Kubalewski3-2/+90
The E810 Lan On Motherboard (LOM) design is vendor specific. Intel provides the reference design, but it is up to vendor on the final product design. For some cases, like Linux DPLL support, the static values defined in the driver does not reflect the actual LOM design. Current implementation of dpll pins is causing the crash on probe of the ice driver for such DPLL enabled E810 LOM designs: WARNING: (...) at drivers/dpll/dpll_core.c:495 dpll_pin_get+0x2c4/0x330 ... Call Trace: <TASK> ? __warn+0x83/0x130 ? dpll_pin_get+0x2c4/0x330 ? report_bug+0x1b7/0x1d0 ? handle_bug+0x42/0x70 ? exc_invalid_op+0x18/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? dpll_pin_get+0x117/0x330 ? dpll_pin_get+0x2c4/0x330 ? dpll_pin_get+0x117/0x330 ice_dpll_get_pins.isra.0+0x52/0xe0 [ice] ... The number of dpll pins enabled by LOM vendor is greater than expected and defined in the driver for Intel designed NICs, which causes the crash. Prevent the crash and allow generic pin initialization within Linux DPLL subsystem for DPLL enabled E810 LOM designs. Newly designed solution for described issue will be based on "per HW design" pin initialization. It requires pin information dynamically acquired from the firmware and is already in progress, planned for next-tree only. Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu") Reviewed-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-10-29ice: block SF port creation in legacy modeMichal Swiatkowski1-0/+6
There is no support for SF in legacy mode. Reflect it in the code. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Fixes: eda69d654c7e ("ice: add basic devlink subfunctions support") Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-10-29igb: Disable threaded IRQ for igb_msix_otherWander Lairson Costa1-1/+1
During testing of SR-IOV, Red Hat QE encountered an issue where the ip link up command intermittently fails for the igbvf interfaces when using the PREEMPT_RT variant. Investigation revealed that e1000_write_posted_mbx returns an error due to the lack of an ACK from e1000_poll_for_ack. The underlying issue arises from the fact that IRQs are threaded by default under PREEMPT_RT. While the exact hardware details are not available, it appears that the IRQ handled by igb_msix_other must be processed before e1000_poll_for_ack times out. However, e1000_write_posted_mbx is called with preemption disabled, leading to a scenario where the IRQ is serviced only after the failure of e1000_write_posted_mbx. To resolve this, we set IRQF_NO_THREAD for the affected interrupt, ensuring that the kernel handles it immediately, thereby preventing the aforementioned error. Reproducer: #!/bin/bash # echo 2 > /sys/class/net/ens14f0/device/sriov_numvfs ipaddr_vlan=3 nic_test=ens14f0 vf=${nic_test}v0 while true; do ip link set ${nic_test} mtu 1500 ip link set ${vf} mtu 1500 ip link set $vf up ip link set ${nic_test} vf 0 vlan ${ipaddr_vlan} ip addr add 172.30.${ipaddr_vlan}.1/24 dev ${vf} ip addr add 2021:db8:${ipaddr_vlan}::1/64 dev ${vf} if ! ip link show $vf | grep 'state UP'; then echo 'Error found' break fi ip link set $vf down done Signed-off-by: Wander Lairson Costa <wander@redhat.com> Fixes: 9d5c824399de ("igb: PCI-Express 82575 Gigabit Ethernet driver") Reported-by: Yuying Ma <yuma@redhat.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-10-08e1000e: change I219 (19) devices to ADPVitaly Lifshits2-4/+4
Sporadic issues, such as PHY access loss, have been observed on I219 (19) devices. It was found that these devices have hardware more closely related to ADP than MTP and the issues were caused by taking MTP-specific flows. Change the MAC and board types of these devices from MTP to ADP to correctly reflect the LAN hardware, and flows, of these devices. Fixes: db2d737d63c5 ("e1000e: Separate MTP board type from ADP") Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08igb: Do not bring the device up after non-fatal errorMohamed Khalfella1-0/+4
Commit 004d25060c78 ("igb: Fix igb_down hung on surprise removal") changed igb_io_error_detected() to ignore non-fatal pcie errors in order to avoid hung task that can happen when igb_down() is called multiple times. This caused an issue when processing transient non-fatal errors. igb_io_resume(), which is called after igb_io_error_detected(), assumes that device is brought down by igb_io_error_detected() if the interface is up. This resulted in panic with stacktrace below. [ T3256] igb 0000:09:00.0 haeth0: igb: haeth0 NIC Link is Down [ T292] pcieport 0000:00:1c.5: AER: Uncorrected (Non-Fatal) error received: 0000:09:00.0 [ T292] igb 0000:09:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID) [ T292] igb 0000:09:00.0: device [8086:1537] error status/mask=00004000/00000000 [ T292] igb 0000:09:00.0: [14] CmpltTO [ 200.105524,009][ T292] igb 0000:09:00.0: AER: TLP Header: 00000000 00000000 00000000 00000000 [ T292] pcieport 0000:00:1c.5: AER: broadcast error_detected message [ T292] igb 0000:09:00.0: Non-correctable non-fatal error reported. [ T292] pcieport 0000:00:1c.5: AER: broadcast mmio_enabled message [ T292] pcieport 0000:00:1c.5: AER: broadcast resume message [ T292] ------------[ cut here ]------------ [ T292] kernel BUG at net/core/dev.c:6539! [ T292] invalid opcode: 0000 [#1] PREEMPT SMP [ T292] RIP: 0010:napi_enable+0x37/0x40 [ T292] Call Trace: [ T292] <TASK> [ T292] ? die+0x33/0x90 [ T292] ? do_trap+0xdc/0x110 [ T292] ? napi_enable+0x37/0x40 [ T292] ? do_error_trap+0x70/0xb0 [ T292] ? napi_enable+0x37/0x40 [ T292] ? napi_enable+0x37/0x40 [ T292] ? exc_invalid_op+0x4e/0x70 [ T292] ? napi_enable+0x37/0x40 [ T292] ? asm_exc_invalid_op+0x16/0x20 [ T292] ? napi_enable+0x37/0x40 [ T292] igb_up+0x41/0x150 [ T292] igb_io_resume+0x25/0x70 [ T292] report_resume+0x54/0x70 [ T292] ? report_frozen_detected+0x20/0x20 [ T292] pci_walk_bus+0x6c/0x90 [ T292] ? aer_print_port_info+0xa0/0xa0 [ T292] pcie_do_recovery+0x22f/0x380 [ T292] aer_process_err_devices+0x110/0x160 [ T292] aer_isr+0x1c1/0x1e0 [ T292] ? disable_irq_nosync+0x10/0x10 [ T292] irq_thread_fn+0x1a/0x60 [ T292] irq_thread+0xe3/0x1a0 [ T292] ? irq_set_affinity_notifier+0x120/0x120 [ T292] ? irq_affinity_notify+0x100/0x100 [ T292] kthread+0xe2/0x110 [ T292] ? kthread_complete_and_exit+0x20/0x20 [ T292] ret_from_fork+0x2d/0x50 [ T292] ? kthread_complete_and_exit+0x20/0x20 [ T292] ret_from_fork_asm+0x11/0x20 [ T292] </TASK> To fix this issue igb_io_resume() checks if the interface is running and the device is not down this means igb_io_error_detected() did not bring the device down and there is no need to bring it up. Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com> Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com> Fixes: 004d25060c78 ("igb: Fix igb_down hung on surprise removal") Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08i40e: Fix macvlan leak by synchronizing access to mac_filter_hashAleksandr Loktionov2-0/+3
This patch addresses a macvlan leak issue in the i40e driver caused by concurrent access to vsi->mac_filter_hash. The leak occurs when multiple threads attempt to modify the mac_filter_hash simultaneously, leading to inconsistent state and potential memory leaks. To fix this, we now wrap the calls to i40e_del_mac_filter() and zeroing vf->default_lan_addr.addr with spin_lock/unlock_bh(&vsi->mac_filter_hash_lock), ensuring atomic operations and preventing concurrent access. Additionally, we add lockdep_assert_held(&vsi->mac_filter_hash_lock) in i40e_add_mac_filter() to help catch similar issues in the future. Reproduction steps: 1. Spawn VFs and configure port vlan on them. 2. Trigger concurrent macvlan operations (e.g., adding and deleting portvlan and/or mac filters). 3. Observe the potential memory leak and inconsistent state in the mac_filter_hash. This synchronization ensures the integrity of the mac_filter_hash and prevents the described leak. Fixes: fed0d9f13266 ("i40e: Fix VF's MAC Address change on VM") Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08ice: Fix increasing MSI-X on VFMarcin Szycik3-5/+9
Increasing MSI-X value on a VF leads to invalid memory operations. This is caused by not reallocating some arrays. Reproducer: modprobe ice echo 0 > /sys/bus/pci/devices/$PF_PCI/sriov_drivers_autoprobe echo 1 > /sys/bus/pci/devices/$PF_PCI/sriov_numvfs echo 17 > /sys/bus/pci/devices/$VF0_PCI/sriov_vf_msix_count Default MSI-X is 16, so 17 and above triggers this issue. KASAN reports: BUG: KASAN: slab-out-of-bounds in ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] Read of size 8 at addr ffff8888b937d180 by task bash/28433 (...) Call Trace: (...) ? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] kasan_report+0xed/0x120 ? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] ice_vsi_cfg_def+0x3360/0x4770 [ice] ? mutex_unlock+0x83/0xd0 ? __pfx_ice_vsi_cfg_def+0x10/0x10 [ice] ? __pfx_ice_remove_vsi_lkup_fltr+0x10/0x10 [ice] ice_vsi_cfg+0x7f/0x3b0 [ice] ice_vf_reconfig_vsi+0x114/0x210 [ice] ice_sriov_set_msix_vec_count+0x3d0/0x960 [ice] sriov_vf_msix_count_store+0x21c/0x300 (...) Allocated by task 28201: (...) ice_vsi_cfg_def+0x1c8e/0x4770 [ice] ice_vsi_cfg+0x7f/0x3b0 [ice] ice_vsi_setup+0x179/0xa30 [ice] ice_sriov_configure+0xcaa/0x1520 [ice] sriov_numvfs_store+0x212/0x390 (...) To fix it, use ice_vsi_rebuild() instead of ice_vf_reconfig_vsi(). This causes the required arrays to be reallocated taking the new queue count into account (ice_vsi_realloc_stat_arrays()). Set req_txq and req_rxq before ice_vsi_rebuild(), so that realloc uses the newly set queue count. Additionally, ice_vsi_rebuild() does not remove VSI filters (ice_fltr_remove_all()), so ice_vf_init_host_cfg() is no longer necessary. Reported-by: Jacob Keller <jacob.e.keller@intel.com> Fixes: 2a2cb4c6c181 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08ice: Flush FDB entries before resetWojciech Drewek3-22/+8
Triggering the reset while in switchdev mode causes errors[1]. Rules are already removed by this time because switch content is flushed in case of the reset. This means that rules were deleted from HW but SW still thinks they exist so when we get SWITCHDEV_FDB_DEL_TO_DEVICE notification we try to delete not existing rule. We can avoid these errors by clearing the rules early in the reset flow before they are removed from HW. Switchdev API will get notified that the rule was removed so we won't get SWITCHDEV_FDB_DEL_TO_DEVICE notification. Remove unnecessary ice_clear_sw_switch_recipes. [1] ice 0000:01:00.0: Failed to delete FDB forward rule, err: -2 ice 0000:01:00.0: Failed to delete FDB guard rule, err: -2 Fixes: 7c945a1a8e5f ("ice: Switchdev FDB events support") Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08ice: Fix netif_is_ice() in Safe ModeMarcin Szycik1-1/+2
netif_is_ice() works by checking the pointer to netdev ops. However, it only checks for the default ice_netdev_ops, not ice_netdev_safe_mode_ops, so in Safe Mode it always returns false, which is unintuitive. While it doesn't look like netif_is_ice() is currently being called anywhere in Safe Mode, this could change and potentially lead to unexpected behaviour. Fixes: df006dd4b1dc ("ice: Add initial support framework for LAG") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-08ice: Fix entering Safe ModeMarcin Szycik1-3/+1
If DDP package is missing or corrupted, the driver should enter Safe Mode. Instead, an error is returned and probe fails. To fix this, don't exit init if ice_init_ddp_config() returns an error. Repro: * Remove or rename DDP package (/lib/firmware/intel/ice/ddp/ice.pkg) * Load ice Fixes: cc5776fe1832 ("ice: Enable switching default Tx scheduler topology") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-10-03Merge branch '100GbE' of ↵Jakub Kicinski12-54/+120
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-09-30 (ice, idpf) This series contains updates to ice and idpf drivers: For ice: Michal corrects setting of dst VSI on LAN filters and adds clearing of port VLAN configuration during reset. Gui-Dong Han corrects failures to decrement refcount in some error paths. Przemek resolves a memory leak in ice_init_tx_topology(). Arkadiusz prevents setting of DPLL_PIN_STATE_SELECTABLE to an improper value. Dave stops clearing of VLAN tracking bit to allow for VLANs to be properly restored after reset. For idpf: Ahmed sets uninitialized dyn_ctl_intrvl_s value. Josh corrects use and reporting of mailbox size. Larysa corrects order of function calls during de-initialization. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: idpf: deinit virtchnl transaction manager after vport and vectors idpf: use actual mbx receive payload length idpf: fix VF dynamic interrupt ctl register initialization ice: fix VLAN replay after reset ice: disallow DPLL_PIN_STATE_SELECTABLE for dpll output pins ice: fix memleak in ice_init_tx_topology() ice: clear port vlan config during reset ice: Fix improper handling of refcount in ice_sriov_set_msix_vec_count() ice: Fix improper handling of refcount in ice_dpll_init_rclk_pins() ice: set correct dst VSI in only LAN filters ==================== Link: https://patch.msgid.link/20240930223601.3137464-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-10-02move asm/unaligned.h to linux/unaligned.hAl Viro2-2/+2
asm/unaligned.h is always an include of asm-generic/unaligned.h; might as well move that thing to linux/unaligned.h and include that - there's nothing arch-specific in that header. auto-generated by the following: for i in `git grep -l -w asm/unaligned.h`; do sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i done for i in `git grep -l -w asm-generic/unaligned.h`; do sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i done git mv include/asm-generic/unaligned.h include/linux/unaligned.h git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
2024-09-30idpf: deinit virtchnl transaction manager after vport and vectorsLarysa Zaremba1-1/+1
When the device is removed, idpf is supposed to make certain virtchnl requests e.g. VIRTCHNL2_OP_DEALLOC_VECTORS and VIRTCHNL2_OP_DESTROY_VPORT. However, this does not happen due to the referenced commit introducing virtchnl transaction manager and placing its deinitialization before those messages are sent. Then the sending is impossible due to no transactions being available. Lack of cleanup can lead to the FW becoming unresponsive from e.g. unloading-loading the driver and creating-destroying VFs afterwards. Move transaction manager deinitialization to after other virtchnl-related cleanup is done. Fixes: 34c21fa894a1 ("idpf: implement virtchnl transaction manager") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-30idpf: use actual mbx receive payload lengthJoshua Hay1-8/+1
When a mailbox message is received, the driver is checking for a non 0 datalen in the controlq descriptor. If it is valid, the payload is attached to the ctlq message to give to the upper layer. However, the payload response size given to the upper layer was taken from the buffer metadata which is _always_ the max buffer size. This meant the API was returning 4K as the payload size for all messages. This went unnoticed since the virtchnl exchange response logic was checking for a response size less than 0 (error), not less than exact size, or not greater than or equal to the max mailbox buffer size (4K). All of these checks will pass in the success case since the size provided is always 4K. However, this breaks anyone that wants to validate the exact response size. Fetch the actual payload length from the value provided in the descriptor data_len field (instead of the buffer metadata). Unfortunately, this means we lose some extra error parsing for variable sized virtchnl responses such as create vport and get ptypes. However, the original checks weren't really helping anyways since the size was _always_ 4K. Fixes: 34c21fa894a1 ("idpf: implement virtchnl transaction manager") Cc: stable@vger.kernel.org # 6.9+ Signed-off-by: Joshua Hay <joshua.a.hay@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-30idpf: fix VF dynamic interrupt ctl register initializationAhmed Zaki1-0/+1
The VF's dynamic interrupt ctl "dyn_ctl_intrvl_s" is not initialized in idpf_vf_intr_reg_init(). This resulted in the following UBSAN error whenever a VF is created: [ 564.345655] UBSAN: shift-out-of-bounds in drivers/net/ethernet/intel/idpf/idpf_txrx.c:3654:10 [ 564.345663] shift exponent 4294967295 is too large for 32-bit type 'int' [ 564.345671] CPU: 33 UID: 0 PID: 2458 Comm: NetworkManager Not tainted 6.11.0-rc4+ #1 [ 564.345678] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C6200.86B.0027.P10.2201070222 01/07/2022 [ 564.345683] Call Trace: [ 564.345688] <TASK> [ 564.345693] dump_stack_lvl+0x91/0xb0 [ 564.345708] __ubsan_handle_shift_out_of_bounds+0x16b/0x320 [ 564.345730] idpf_vport_intr_update_itr_ena_irq.cold+0x13/0x39 [idpf] [ 564.345755] ? __pfx_idpf_vport_intr_update_itr_ena_irq+0x10/0x10 [idpf] [ 564.345771] ? static_obj+0x95/0xd0 [ 564.345782] ? lockdep_init_map_type+0x1a5/0x800 [ 564.345794] idpf_vport_intr_ena+0x5ef/0x9f0 [idpf] [ 564.345814] idpf_vport_open+0x2cc/0x1240 [idpf] [ 564.345837] idpf_open+0x6d/0xc0 [idpf] [ 564.345850] __dev_open+0x241/0x420 Fixes: d4d558718266 ("idpf: initialize interrupts and enable vport") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-30ice: fix VLAN replay after resetDave Ertman1-2/+0
There is a bug currently when there are more than one VLAN defined and any reset that affects the PF is initiated, after the reset rebuild no traffic will pass on any VLAN but the last one created. This is caused by the iteration though the VLANs during replay each clearing the vsi_map bitmap of the VSI that is being replayed. The problem is that during rhe replay, the pointer to the vsi_map bitmap is used by each successive vlan to determine if it should be replayed on this VSI. The logic was that the replay of the VLAN would replace the bit in the map before the next VLAN would iterate through. But, since the replay copies the old bitmap pointer to filt_replay_rules and creates a new one for the recreated VLANS, it does not do this, and leaves the old bitmap broken to be used to replay the remaining VLANs. Since the old bitmap will be cleaned up in post replay cleanup, there is no need to alter it and break following VLAN replay, so don't clear the bit. Fixes: 334cb0626de1 ("ice: Implement VSI replay framework") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-30ice: disallow DPLL_PIN_STATE_SELECTABLE for dpll output pinsArkadiusz Kubalewski1-0/+2
Currently the user may request DPLL_PIN_STATE_SELECTABLE for an output pin, and this would actually set the DISCONNECTED state instead. It doesn't make any sense. SELECTABLE is valid only in case of input pins (on AUTOMATIC type dpll), where dpll itself would select best valid input. For the output pin only CONNECTED/DISCONNECTED are expected. Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu") Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-30ice: fix memleak in ice_init_tx_topology()Przemek Kitszel3-39/+31
Fix leak of the FW blob (DDP pkg). Make ice_cfg_tx_topo() const-correct, so ice_init_tx_topology() can avoid copying whole FW blob. Copy just the topology section, and only when needed. Reuse the buffer allocated for the read of the current topology. This was found by kmemleak, with the following trace for each PF: [<ffffffff8761044d>] kmemdup_noprof+0x1d/0x50 [<ffffffffc0a0a480>] ice_init_ddp_config+0x100/0x220 [ice] [<ffffffffc0a0da7f>] ice_init_dev+0x6f/0x200 [ice] [<ffffffffc0a0dc49>] ice_init+0x29/0x560 [ice] [<ffffffffc0a10c1d>] ice_probe+0x21d/0x310 [ice] Constify ice_cfg_tx_topo() @buf parameter. This cascades further down to few more functions. Fixes: cc5776fe1832 ("ice: Enable switching default Tx scheduler topology") CC: Larysa Zaremba <larysa.zaremba@intel.com> CC: Jacob Keller <jacob.e.keller@intel.com> CC: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> CC: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-30ice: clear port vlan config during resetMichal Swiatkowski3-0/+65
Since commit 2a2cb4c6c181 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()") VF VSI is only reconfigured instead of recreated. The context configuration from previous setting is still the same. If any of the config needs to be cleared it needs to be cleared explicitly. Previously there was assumption that port vlan will be cleared automatically. Now, when VSI is only reconfigured we have to do it in the code. Not clearing port vlan configuration leads to situation when the driver VSI config is different than the VSI config in HW. Traffic can't be passed after setting and clearing port vlan, because of invalid VSI config in HW. Example reproduction: > ip a a dev $(VF) $(VF_IP_ADDRESS) > ip l s dev $(VF) up > ping $(VF_IP_ADDRESS) ping is working fine here > ip link set eth5 vf 0 vlan 100 > ip link set eth5 vf 0 vlan 0 > ping $(VF_IP_ADDRESS) ping isn't working Fixes: 2a2cb4c6c181 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()") Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Piotr Tyda <piotr.tyda@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-30ice: Fix improper handling of refcount in ice_sriov_set_msix_vec_count()Gui-Dong Han1-2/+6
This patch addresses an issue with improper reference count handling in the ice_sriov_set_msix_vec_count() function. First, the function calls ice_get_vf_by_id(), which increments the reference count of the vf pointer. If the subsequent call to ice_get_vf_vsi() fails, the function currently returns an error without decrementing the reference count of the vf pointer, leading to a reference count leak. The correct behavior, as implemented in this patch, is to decrement the reference count using ice_put_vf(vf) before returning an error when vsi is NULL. Second, the function calls ice_sriov_get_irqs(), which sets vf->first_vector_idx. If this call returns a negative value, indicating an error, the function returns an error without decrementing the reference count of the vf pointer, resulting in another reference count leak. The patch addresses this by adding a call to ice_put_vf(vf) before returning an error when vf->first_vector_idx < 0. This bug was identified by an experimental static analysis tool developed by our team. The tool specializes in analyzing reference count operations and identifying potential mismanagement of reference counts. In this case, the tool flagged the missing decrement operation as a potential issue, leading to this patch. Fixes: 4035c72dc1ba ("ice: reconfig host after changing MSI-X on VF") Fixes: 4d38cb44bd32 ("ice: manage VFs MSI-X using resource tracking") Cc: stable@vger.kernel.org Signed-off-by: Gui-Dong Han <hanguidong02@outlook.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-30ice: Fix improper handling of refcount in ice_dpll_init_rclk_pins()Gui-Dong Han1-2/+2
This patch addresses a reference count handling issue in the ice_dpll_init_rclk_pins() function. The function calls ice_dpll_get_pins(), which increments the reference count of the relevant resources. However, if the condition WARN_ON((!vsi || !vsi->netdev)) is met, the function currently returns an error without properly releasing the resources acquired by ice_dpll_get_pins(), leading to a reference count leak. To resolve this, the check has been moved to the top of the function. This ensures that the function verifies the state before any resources are acquired, avoiding the need for additional resource management in the error path. This bug was identified by an experimental static analysis tool developed by our team. The tool specializes in analyzing reference count operations and detecting potential issues where resources are not properly managed. In this case, the tool flagged the missing release operation as a potential problem, which led to the development of this patch. Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu") Cc: stable@vger.kernel.org Signed-off-by: Gui-Dong Han <hanguidong02@outlook.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-30ice: set correct dst VSI in only LAN filtersMichal Swiatkowski1-0/+11
The filters set that will reproduce the problem: $ tc filter add dev $VF0_PR ingress protocol arp prio 0 flower \ skip_sw dst_mac ff:ff:ff:ff:ff:ff action mirred egress \ redirect dev $PF0 $ tc filter add dev $VF0_PR ingress protocol arp prio 0 flower \ skip_sw dst_mac ff:ff:ff:ff:ff:ff src_mac 52:54:00:00:00:10 \ action mirred egress mirror dev $VF1_PR Expected behaviour is to set all broadcast from VF0 to the LAN. If the src_mac match the value from filters, send packet to LAN and to VF1. In this case both LAN_EN and LB_EN flags in switch is set in case of packet matching both filters. As dst VSI for the only LAN enable bit is PF VSI, the packet is being seen on PF. To fix this change dst VSI to the source VSI. It will block receiving any packet even when LB_EN is set by switch, because local loopback is clear on VF VSI during normal operation. Side note: if the second filters action is redirect instead of mirror LAN_EN is clear, because switch is AND-ing LAN_EN from each matched filters and OR-ing LB_EN. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Fixes: 73b483b79029 ("ice: Manage act flags for switchdev offloads") Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-15ice: Fix a NULL vs IS_ERR() check in probe()Dan Carpenter1-2/+2
The ice_allocate_sf() function returns error pointers on error. It doesn't return NULL. Update the check to match. Fixes: 177ef7f1e2a0 ("ice: base subfunction aux driver") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/6951d217-ac06-4482-a35d-15d757fd90a3@stanley.mountain Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-09-15ice: Fix a couple NULL vs IS_ERR() bugsDan Carpenter1-4/+4
The ice_repr_create() function returns error pointers. It never returns NULL. Fix the callers to check for IS_ERR(). Fixes: 977514fb0fa8 ("ice: create port representor for SF") Fixes: 415db8399d06 ("ice: make representor code generic") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/7f7aeb91-8771-47b8-9275-9d9f64f947dd@stanley.mountain Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-09-12Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski4-15/+23
Cross-merge networking fixes after downstream PR. No conflicts (sort of) and no adjacent changes. This merge reverts commit b3c9e65eb227 ("net: hsr: remove seqnr_lock") from net, as it was superseded by commit 430d67bdcb04 ("net: hsr: Use the seqnr lock for frames received via interlink port.") in net-next. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-09-11Merge branch '200GbE' of ↵Jakub Kicinski5-325/+276
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue Tony Nguyen says: ==================== idpf: XDP chapter II: convert Tx completion to libeth Alexander Lobakin says: XDP for idpf is currently 5 chapters: * convert Rx to libeth; * convert Tx completion to libeth (this); * generic XDP and XSk code changes; * actual XDP for idpf via libeth_xdp; * XSk for idpf (^). Part II does the following: * adds generic libeth Tx completion routines; * converts idpf to use generic libeth Tx comp routines; * fixes Tx queue timeouts and robustifies Tx completion in general; * fixes Tx event/descriptor flushes (writebacks). Most idpf patches again remove more lines than adds. Generic Tx completion helpers and structs are needed as libeth_xdp (Ch. III) makes use of them. WB_ON_ITR is needed since XDPSQs don't want to work without it at all. Tx queue timeouts fixes are needed since without them, it's way easier to catch a Tx timeout event when WB_ON_ITR is enabled. * '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: idpf: enable WB_ON_ITR idpf: fix netdev Tx queue stop/wake idpf: refactor Tx completion routines netdevice: add netdev_tx_reset_subqueue() shorthand idpf: convert to libeth Tx buffer completion libeth: add Tx buffer completion helpers ==================== Link: https://patch.msgid.link/20240909205323.3110312-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-09-09idpf: enable WB_ON_ITRJoshua Hay5-3/+41
Tell hardware to write back completed descriptors even when interrupts are disabled. Otherwise, descriptors might not be written back until the hardware can flush a full cacheline of descriptors. This can cause unnecessary delays when traffic is light (or even trigger Tx queue timeout). The example scenario to reproduce the Tx timeout if the fix is not applied: - configure at least 2 Tx queues to be assigned to the same q_vector, - generate a huge Tx traffic on the first Tx queue - try to send a few packets using the second Tx queue. In such a case Tx timeout will appear on the second Tx queue because no completion descriptors are written back for that queue while interrupts are disabled due to NAPI polling. Fixes: c2d548cad150 ("idpf: add TX splitq napi poll support") Fixes: a5ab9ee0df0b ("idpf: add singleq start_xmit and napi poll") Signed-off-by: Joshua Hay <joshua.a.hay@intel.com> Co-developed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09idpf: fix netdev Tx queue stop/wakeMichal Kubiak3-27/+21
netif_txq_maybe_stop() returns -1, 0, or 1, while idpf_tx_maybe_stop_common() says it returns 0 or -EBUSY. As a result, there sometimes are Tx queue timeout warnings despite that the queue is empty or there is at least enough space to restart it. Make idpf_tx_maybe_stop_common() inline and returning true or false, handling the return of netif_txq_maybe_stop() properly. Use a correct goto in idpf_tx_maybe_stop_splitq() to avoid stopping the queue or incrementing the stops counter twice. Fixes: 6818c4d5b3c2 ("idpf: add splitq start_xmit") Fixes: a5ab9ee0df0b ("idpf: add singleq start_xmit and napi poll") Cc: stable@vger.kernel.org # 6.7+ Signed-off-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09idpf: refactor Tx completion routinesJoshua Hay3-76/+122
Add a mechanism to guard against stashing partial packets into the hash table to make the driver more robust, with more efficient decision making when cleaning. Don't stash partial packets. This can happen when an RE (Report Event) completion is received in flow scheduling mode, or when an out of order RS (Report Status) completion is received. The first buffer with the skb is stashed, but some or all of its frags are not because the stack is out of reserve buffers. This leaves the ring in a weird state since the frags are still on the ring. Use the field libeth_sqe::nr_frags to track the number of fragments/tx_bufs representing the packet. The clean routines check to make sure there are enough reserve buffers on the stack before stashing any part of the packet. If there are not, next_to_clean is left pointing to the first buffer of the packet that failed to be stashed. This leaves the whole packet on the ring, and the next time around, cleaning will start from this packet. An RS completion is still expected for this packet in either case. So instead of being cleaned from the hash table, it will be cleaned from the ring directly. This should all still be fine since the DESC_UNUSED and BUFS_UNUSED will reflect the state of the ring. If we ever fall below the thresholds, the TxQ will still be stopped, giving the completion queue time to catch up. This may lead to stopping the queue more frequently, but it guarantees the Tx ring will always be in a good state. Also, always use the idpf_tx_splitq_clean function to clean descriptors, i.e. use it from clean_buf_ring as well. This way we avoid duplicating the logic and make sure we're using the same reserve buffers guard rail. This does require a switch from the s16 next_to_clean overflow descriptor ring wrap calculation to u16 and the normal ring size check. Signed-off-by: Joshua Hay <joshua.a.hay@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09idpf: convert to libeth Tx buffer completionAlexander Lobakin3-232/+105
&idpf_tx_buffer is almost identical to the previous generations, as well as the way it's handled. Moreover, relying on dma_unmap_addr() and !!buf->skb instead of explicit defining of buffer's type was never good. Use the newly added libeth helpers to do it properly and reduce the copy-paste around the Tx code. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09igb: Always call igb_xdp_ring_update_tail() under Tx lockSriram Yagnaraman1-4/+13
Always call igb_xdp_ring_update_tail() under __netif_tx_lock, add a comment and lockdep assert to indicate that. This is needed to share the same TX ring between XDP, XSK and slow paths. Furthermore, the current XDP implementation is racy on tail updates. Fixes: 9cbc948b5a20 ("igb: add XDP support") Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech> [Kurt: Add lockdep assert and fixes tag] Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09ice: fix VSI lists confusion when adding VLANsMichal Schmidt1-1/+1
The description of function ice_find_vsi_list_entry says: Search VSI list map with VSI count 1 However, since the blamed commit (see Fixes below), the function no longer checks vsi_count. This causes a problem in ice_add_vlan_internal, where the decision to share VSI lists between filter rules relies on the vsi_count of the found existing VSI list being 1. The reproducing steps: 1. Have a PF and two VFs. There will be a filter rule for VLAN 0, referring to a VSI list containing VSIs: 0 (PF), 2 (VF#0), 3 (VF#1). 2. Add VLAN 1234 to VF#0. ice will make the wrong decision to share the VSI list with the new rule. The wrong behavior may not be immediately apparent, but it can be observed with debug prints. 3. Add VLAN 1234 to VF#1. ice will unshare the VSI list for the VLAN 1234 rule. Due to the earlier bad decision, the newly created VSI list will contain VSIs 0 (PF) and 3 (VF#1), instead of expected 2 (VF#0) and 3 (VF#1). 4. Try pinging a network peer over the VLAN interface on VF#0. This fails. Reproducer script at: https://gitlab.com/mschmidt2/repro/-/blob/master/RHEL-46814/test-vlan-vsi-list-confusion.sh Commented debug trace: https://gitlab.com/mschmidt2/repro/-/blob/master/RHEL-46814/ice-vlan-vsi-lists-debug.txt Patch adding the debug prints: https://gitlab.com/mschmidt2/linux/-/commit/f8a8814623944a45091a77c6094c40bfe726bfdb (Unsafe, by the way. Lacks rule_lock when dumping in ice_remove_vlan.) Michal Swiatkowski added to the explanation that the bug is caused by reusing a VSI list created for VLAN 0. All created VFs' VSIs are added to VLAN 0 filter. When a non-zero VLAN is created on a VF which is already in VLAN 0 (normal case), the VSI list from VLAN 0 is reused. It leads to a problem because all VFs (VSIs to be specific) that are subscribed to VLAN 0 will now receive a new VLAN tag traffic. This is one bug, another is the bug described above. Removing filters from one VF will remove VLAN filter from the previous VF. It happens a VF is reset. Example: - creation of 3 VFs - we have VSI list (used for VLAN 0) [0 (pf), 2 (vf1), 3 (vf2), 4 (vf3)] - we are adding VLAN 100 on VF1, we are reusing the previous list because 2 is there - VLAN traffic works fine, but VLAN 100 tagged traffic can be received on all VSIs from the list (for example broadcast or unicast) - trust is turning on VF2, VF2 is resetting, all filters from VF2 are removed; the VLAN 100 filter is also removed because 3 is on the list - VLAN traffic to VF1 isn't working anymore, there is a need to recreate VLAN interface to readd VLAN filter One thing I'm not certain about is the implications for the LAG feature, which is another caller of ice_find_vsi_list_entry. I don't have a LAG-capable card at hand to test. Fixes: 23ccae5ce15f ("ice: changes to the interface with the HW and FW for SRIOV_VF+LAG") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Dave Ertman <David.m.ertman@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09ice: stop calling pci_disable_device() as we use pcimPrzemek Kitszel1-2/+0
Our driver uses devres to manage resources, in particular we call pcim_enable_device(), what also means we express the intent to get automatic pci_disable_device() call at driver removal. Manual calls to pci_disable_device() misuse the API. Recent commit (see "Fixes" tag) has changed the removal action from conditional (silent ignore of double call to pci_disable_device()) to unconditional, but able to catch unwanted redundant calls; see cited "Fixes" commit for details. Since that, unloading the driver yields following warn+splat: [70633.628490] ice 0000:af:00.7: disabling already-disabled device [70633.628512] WARNING: CPU: 52 PID: 33890 at drivers/pci/pci.c:2250 pci_disable_device+0xf4/0x100 ... [70633.628744] ? pci_disable_device+0xf4/0x100 [70633.628752] release_nodes+0x4a/0x70 [70633.628759] devres_release_all+0x8b/0xc0 [70633.628768] device_unbind_cleanup+0xe/0x70 [70633.628774] device_release_driver_internal+0x208/0x250 [70633.628781] driver_detach+0x47/0x90 [70633.628786] bus_remove_driver+0x80/0x100 [70633.628791] pci_unregister_driver+0x2a/0xb0 [70633.628799] ice_module_exit+0x11/0x3a [ice] Note that this is the only Intel ethernet driver that needs such fix. Fixes: f748a07a0b64 ("PCI: Remove legacy pcim_release()") Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Philipp Stanner <pstanner@redhat.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09ice: fix accounting for filters shared by multiple VSIsJacob Keller1-1/+1
When adding a switch filter (such as a MAC or VLAN filter), it is expected that the driver will detect the case where the filter already exists, and return -EEXIST. This is used by calling code such as ice_vc_add_mac_addr, and ice_vsi_add_vlan to avoid incrementing the accounting fields such as vsi->num_vlan or vf->num_mac. This logic works correctly for the case where only a single VSI has added a given switch filter. When a second VSI adds the same switch filter, the driver converts the existing filter from an ICE_FWD_TO_VSI filter into an ICE_FWD_TO_VSI_LIST filter. This saves switch resources, by ensuring that multiple VSIs can re-use the same filter. The ice_add_update_vsi_list() function is responsible for doing this conversion. When first converting a filter from the FWD_TO_VSI into FWD_TO_VSI_LIST, it checks if the VSI being added is the same as the existing rule's VSI. In such a case it returns -EEXIST. However, when the switch rule has already been converted to a FWD_TO_VSI_LIST, the logic is different. Adding a new VSI in this case just requires extending the VSI list entry. The logic for checking if the rule already exists in this case returns 0 instead of -EEXIST. This breaks the accounting logic mentioned above, so the counters for how many MAC and VLAN filters exist for a given VF or VSI no longer accurately reflect the actual count. This breaks other code which relies on these counts. In typical usage this primarily affects such filters generally shared by multiple VSIs such as VLAN 0, or broadcast and multicast MAC addresses. Fix this by correctly reporting -EEXIST in the case of adding the same VSI to a switch rule already converted to ICE_FWD_TO_VSI_LIST. Fixes: 9daf8208dd4d ("ice: Add support for switch filter programming") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-09ice: Fix lldp packets dropping after changing the number of channelsMartyna Szapar-Mudlaw1-7/+8
After vsi setup refactor commit 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") ice_cfg_sw_lldp function which removes rx rule directing LLDP packets to vsi is moved from ice_vsi_release to ice_vsi_decfg function. ice_vsi_decfg is used in more cases than just in vsi_release resulting in unnecessary removal of rx lldp packets handling switch rule. This leads to lldp packets being dropped after a change number of channels via ethtool. This patch moves ice_cfg_sw_lldp function that removes rx lldp sw rule back to ice_vsi_release function. Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") Reported-by: Matěj Grégr <mgregr@netx.as> Closes: https://lore.kernel.org/intel-wired-lan/1be45a76-90af-4813-824f-8398b69745a9@netx.as/T/#u Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-06ice: subfunction activation and base devlink opsPiotr Raczynski4-0/+290
Use previously implemented SF aux driver. It is probe during SF activation and remove after deactivation. Implement set/get hw_address and set/get state as basic devlink ops for subfunction. Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-06ice: basic support for VLAN in subfunctionsMichal Swiatkowski4-0/+39
Implement add / delete vlan for subfunction type VSI. Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-06ice: support subfunction devlink Tx topologyMichal Swiatkowski3-5/+20
Flow for creating Tx topology is the same as for VF port representors, but the devlink port is stored in different place (sf->devlink_port). When creating VF devlink lock isn't taken, when creating subfunction it is. Setting Tx topology function needs to take this lock, check if it was taken before to not do it twice. Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-06ice: implement netdevice ops for SF representorMichal Swiatkowski1-14/+43
Subfunction port representor needs the basic netdevice ops to work correctly. Create them. Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-06ice: check if SF is ready in ethtool opsMichal Swiatkowski3-4/+16
Now there is another type of port representor. Correct checking if parent device is ready to reflect also new PR type. Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-06ice: don't set target VSI for subfunctionMichal Swiatkowski1-1/+1
Add check for subfunction before setting target VSI. It is needed for PF in switchdev mode but not for subfunction (even in switchdev mode). Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-06ice: create port representor for SFMichal Swiatkowski6-4/+113
Implement attaching and detaching SF port representor. It is done in the same way as the VF port representor. SF port representor is always added or removed with devlink lock taken. Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-09-06ice: make representor code genericMichal Swiatkowski7-76/+121
Keep the same flow of port representor creation, but instead of general attach function create helpers for specific representor type. Store function pointer for add and remove representor. Type of port representor can be also known based on VSI type, but it is more clean to have it directly saved in port representor structure. Add devlink lock for whole port representor creation and destruction. Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Powered by cgit, Gruvboxed by Blaster4385.