| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The tstamp_config structure is being set inside of
ice_ptp_cfg_timestamp, which is the function used to set Tx and
Rx timestamping during initialization.
This function is also used in order to set the PHY port timestamping
status. However, it makes sense to always set the tstamp_config directly
whenever the ice_set_tx_tstamp or ice_set_rx_tstamp functions are
called.
Move assignment of tstamp_config into the related functions and out of
ice_ptp_cfg_timestamp.
Now that we assign the timestamp mode in the relevant functions, we no
longer modify the config value in ice_set_timestamp_mode. In turn, we
no longer want to copy that config value into the PF cached structure.
Instead, this is now the source of truth for actual configuration. On
success of ice_set_timestamp_mode, copy the real configured mode back to
report it out to userspace.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
A future change will add additional possible increment values for the
E822 device support. To handle this, we want to look up the increment
value to use instead of hard coding it to the nominal value for E810
devices. Introduce ice_base_incval as a function to get the best nominal
increment value to use.
For now, it just returns the E810 value, but will be refactored in the
future to look up the value based on the device type and configured
clock frequency.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The PF reset does not reset PHC and PHY clocks so it's unnecessary to
stop them and reinitialize after the reset.
Configuring timestamping changes the VSI fields so it needs to be
performed after VSIs are initialized, which was not done in case of a
reset.
Suggested-by: Patrick Talbert <[email protected]>
Signed-off-by: Karol Kolacinski <[email protected]>
Tested-by: Pasi Vaananen <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Recent net core changes caused an issue with few Intel drivers
(reportedly igb), where taking RTNL in RPM resume path results in a
deadlock. See [0] for a bug report. I don't think the core changes
are wrong, but taking RTNL in RPM resume path isn't needed.
The Intel drivers are the only ones doing this. See [1] for a
discussion on the issue. Following patch changes the RPM resume path
to not take RTNL.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=215129
[1] https://lore.kernel.org/netdev/20211125074949.5f897431@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/t/
Fixes: bd869245a3dc ("net: core: try to runtime-resume detached device in __dev_open")
Fixes: f32a21376573 ("ethtool: runtime-resume netdev parent before ethtool ioctl ops")
Tested-by: Martin Stolpe <[email protected]>
Signed-off-by: Heiner Kallweit <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
For VIRTCHNL_VF_OFFLOAD_VLAN, PF's would limit the number of VLAN
filters a VF was allowed to add. However, by the time the opcode failed,
the VLAN netdev had already been added. VIRTCHNL_VF_OFFLOAD_VLAN_V2
added the ability for a PF to tell the VF how many VLAN filters it's
allowed to add. Make changes to support that functionality.
Signed-off-by: Brett Creeley <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows
the VF to support 802.1Q and 802.1ad VLAN insertion and stripping if
successfully negotiated via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS.
Multiple changes were needed to support this new functionality.
1. Added new aq_required flags to support any kind of VLAN stripping and
insertion offload requests via virtchnl.
2. Added the new method iavf_set_vlan_offload_features() that's
used during VF initialization, VF reset, and iavf_set_features() to
set the aq_required bits based on the current VLAN offload
configuration of the VF's netdev.
3. Added virtchnl handling for VIRTCHNL_OP_ENABLE_STRIPPING_V2,
VIRTCHNL_OP_DISABLE_STRIPPING_V2, VIRTCHNL_OP_ENABLE_INSERTION_V2,
and VIRTCHNL_OP_ENABLE_INSERTION_V2.
Signed-off-by: Brett Creeley <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows
the PF to set the location of the Tx and Rx VLAN tag for insertion and
stripping offloads. In order to support this functionality a few changes
are needed.
1. Add a new method to cache the VLAN tag location based on negotiated
capabilities for the Tx and Rx ring flags. This needs to be called in
the initialization and reset paths.
2. Refactor the transmit hotpath to account for the new Tx ring flags.
When IAVF_TXR_FLAGS_VLAN_LOC_L2TAG2 is set, then the driver needs to
insert the VLAN tag in the L2TAG2 field of the transmit descriptor.
When the IAVF_TXRX_FLAGS_VLAN_LOC_L2TAG1 is set, then the driver needs
to use the l2tag1 field of the data descriptor (same behavior as
before).
3. Refactor the iavf_tx_prepare_vlan_flags() function to simplify
transmit hardware VLAN offload functionality by only depending on the
skb_vlan_tag_present() function. This can be done because the OS
won't request transmit offload for a VLAN unless the driver told the
OS it's supported and enabled.
4. Refactor the receive hotpath to account for the new Rx ring flags and
VLAN ethertypes. This requires checking the Rx ring flags and
descriptor status bits to determine the location of the VLAN tag.
Also, since only a single ethertype can be supported at a time, check
the enabled netdev features before specifying a VLAN ethertype in
__vlan_hwaccel_put_tag().
Signed-off-by: Brett Creeley <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Based on VIRTCHNL_VF_OFFLOAD_VLAN_V2, the VF can now support more VLAN
capabilities (i.e. 802.1AD offloads and filtering). In order to
communicate these capabilities to the netdev layer, the VF needs to
parse its VLAN capabilities based on whether it was able to negotiation
VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or neither of
these.
In order to support this, add the following functionality:
iavf_get_netdev_vlan_hw_features() - This is used to determine the VLAN
features that the underlying hardware supports and that can be toggled
off/on based on the negotiated capabiltiies. For example, if
VIRTCHNL_VF_OFFLOAD_VLAN_V2 was negotiated, then any capability marked
with VIRTCHNL_VLAN_TOGGLE can be toggled on/off by the VF. If
VIRTCHNL_VF_OFFLOAD_VLAN was negotiated, then only VLAN insertion and/or
stripping can be toggled on/off.
iavf_get_netdev_vlan_features() - This is used to determine the VLAN
features that the underlying hardware supports and that should be
enabled by default. For example, if VIRTHCNL_VF_OFFLOAD_VLAN_V2 was
negotiated, then any supported capability that has its ethertype_init
filed set should be enabled by default. If VIRTCHNL_VF_OFFLOAD_VLAN was
negotiated, then filtering, stripping, and insertion should be enabled
by default.
Also, refactor iavf_fix_features() to take into account the new
capabilities. To do this, query all the supported features (enabled by
default and toggleable) and make sure the requested change is supported.
If VIRTCHNL_VF_OFFLOAD_VLAN_V2 is successfully negotiated, there is no
need to check VIRTCHNL_VLAN_TOGGLE here because the driver already told
the netdev layer which features can be toggled via netdev->hw_features
during iavf_process_config(), so only those features will be requested
to change.
Signed-off-by: Brett Creeley <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In order to support the new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability the
VF driver needs to rework it's initialization state machine and reset
flow. This has to be done because successful negotiation of
VIRTCHNL_VF_OFFLOAD_VLAN_V2 requires the VF driver to perform a second
capability request via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS before
configuring the adapter and its netdev.
Add the VIRTCHNL_VF_OFFLOAD_VLAN_V2 bit when sending the
VIRTHCNL_OP_GET_VF_RESOURECES message. The underlying PF will either
support VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or
neither. Both of these offloads should never be supported together.
Based on this, add 2 new states to the initialization state machine:
__IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS
__IAVF_INIT_CONFIG_ADAPTER
The __IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS state is used to request/store
the new VLAN capabilities if and only if VIRTCHNL_VLAN_OFFLOAD_VLAN_V2
was successfully negotiated in the __IAVF_INIT_GET_RESOURCES state.
The __IAVF_INIT_CONFIG_ADAPTER state is used to configure the
adapter/netdev after the resource requests have finished. The VF will
move into this state regardless of whether it successfully negotiated
VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2.
Also, add a the new flag IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS and set
it during VF reset. If VIRTCHNL_VF_OFFLOAD_VLAN_V2 was successfully
negotiated then the VF will request its VLAN capabilities via
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS during the reset. This is needed
because the PF may change/modify the VF's configuration during VF reset
(i.e. modifying the VF's port VLAN configuration).
This also, required the VF to call netdev_update_features() since its
VLAN features may change during VF reset. Make sure to call this under
rtnl_lock().
Signed-off-by: Brett Creeley <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Currently cleaned_count is initialized to ICE_DESC_UNUSED(rx_ring) and
later on during the Rx processing it is incremented per each frame that
driver consumed. This can result in excessive buffers requested from xsk
pool based on that value.
To address this, just drop cleaned_count and pass
ICE_DESC_UNUSED(rx_ring) directly as a function argument to
ice_alloc_rx_bufs_zc(). Idea is to ask for buffers as many as consumed.
Let us also call ice_alloc_rx_bufs_zc unconditionally at the end of
ice_clean_rx_irq_zc. This has been changed in that way for corresponding
ice_clean_rx_irq, but not here.
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <[email protected]>
Tested-by: Kiran Bhandare <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Commit ac6f733a7bd5 ("ice: allow empty Rx descriptors") stated that ice
HW can produce empty descriptors that are valid and they should be
processed.
Add this support to xsk ZC path to avoid potential processing problems.
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <[email protected]>
Tested-by: Kiran Bhandare <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The descriptor that ntu is pointing at when we exit
ice_alloc_rx_bufs_zc() should not have its corresponding DD bit cleared
as descriptor is not allocated in there and it is not valid for HW
usage.
The allocation routine at the entry will fill the descriptor that ntu
points to after it was set to ntu + nb_buffs on previous call.
Even the spec says:
"The tail pointer should be set to one descriptor beyond the last empty
descriptor in host descriptor ring."
Therefore, step away from clearing the status_error0 on ntu + nb_buffs
descriptor.
Fixes: db804cfc21e9 ("ice: Use the xsk batched rx allocation interface")
Reported-by: Elza Mathew <[email protected]>
Signed-off-by: Maciej Fijalkowski <[email protected]>
Tested-by: Kiran Bhandare <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The 'if (ntu == rx_ring->count)' block in ice_alloc_rx_buffers_zc()
was previously residing in the loop, but after introducing the
batched interface it is used only to wrap-around the NTU descriptor,
thus no more need to assign 'xdp'.
Fixes: db804cfc21e9 ("ice: Use the xsk batched rx allocation interface")
Signed-off-by: Alexander Lobakin <[email protected]>
Acked-by: Maciej Fijalkowski <[email protected]>
Tested-by: Kiran Bhandare <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Currently, the zero-copy data path is reusing the memory region that was
initially allocated for an array of struct ice_rx_buf for its own
purposes. This is error prone as it is based on the ice_rx_buf struct
always being the same size or bigger than what the zero-copy path needs.
There can also be old values present in that array giving rise to errors
when the zero-copy path uses it.
Fix this by freeing the ice_rx_buf region and allocating a new array for
the zero-copy path that has the right length and is initialized to zero.
Fixes: 57f7f8b6bc0b ("ice: Use xdp_buf instead of rx_buf for xsk zero-copy")
Signed-off-by: Maciej Fijalkowski <[email protected]>
Tested-by: Kiran Bhandare <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Currently we only NULL the xdp_buff pointer in the internal SW ring but
we never give it back to the xsk buffer pool. This means that buffers
can be leaked out of the buff pool and never be used again.
Add missing xsk_buff_free() call to the routine that is supposed to
clean the entries that are left in the ring so that these buffers in the
umem can be used by other sockets.
Also, only go through the space that is actually left to be cleaned
instead of a whole ring.
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Magnus Karlsson <[email protected]>
Signed-off-by: Maciej Fijalkowski <[email protected]>
Tested-by: Kiran Bhandare <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db7272798 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Commit a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:
https://sourceforge.net/p/e1000/mailman/message/37106269/
However, the suppression was not documented at all, nor was how to
enable NBASE-T support.
Properly document the NBASE-T suppression and how to enable NBASE-T
support.
Fixes: a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <[email protected]>
Signed-off-by: Robert Schlabbach <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.
Fixes: 707abf069548 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <[email protected]>
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
The KASAN logs are as follows:
[ 35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[ 35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[ 35.128360]
[ 35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[ 35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[ 35.131749] Call Trace:
[ 35.132199] dump_stack_lvl+0x59/0x7b
[ 35.132865] print_address_description+0x7c/0x3b0
[ 35.133707] ? free_netdev+0x1fd/0x450
[ 35.134378] __kasan_report+0x160/0x1c0
[ 35.135063] ? free_netdev+0x1fd/0x450
[ 35.135738] kasan_report+0x4b/0x70
[ 35.136367] free_netdev+0x1fd/0x450
[ 35.137006] igbvf_probe+0x121d/0x1a10 [igbvf]
[ 35.137808] ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[ 35.138751] local_pci_probe+0x13c/0x1f0
[ 35.139461] pci_device_probe+0x37e/0x6c0
[ 35.165526]
[ 35.165806] Allocated by task 366:
[ 35.166414] ____kasan_kmalloc+0xc4/0xf0
[ 35.167117] foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[ 35.168078] igbvf_probe+0x9c5/0x1a10 [igbvf]
[ 35.168866] local_pci_probe+0x13c/0x1f0
[ 35.169565] pci_device_probe+0x37e/0x6c0
[ 35.179713]
[ 35.179993] Freed by task 366:
[ 35.180539] kasan_set_track+0x4c/0x80
[ 35.181211] kasan_set_free_info+0x1f/0x40
[ 35.181942] ____kasan_slab_free+0x103/0x140
[ 35.182703] kfree+0xe3/0x250
[ 35.183239] igbvf_probe+0x1173/0x1a10 [igbvf]
[ 35.184040] local_pci_probe+0x13c/0x1f0
Fixes: d4e0fe01a38a0 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <[email protected]>
Signed-off-by: Letu Ren <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
Fixes: 1b8b062a99dc ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The kernel gained a new interface for drivers to use to combine tail
bump (doorbell) and BQL updates, attempt to use those new interfaces.
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The driver had comments to the effect of: This flag should be set before
calling this function. While reviewing code it was found that there were
several violations of this policy, which could introduce hard to find
bugs or races.
Fix the violations of the "VSI DOWN state must be set before calling
ice_down" and make checking the state into code with a WARN_ON.
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The kernel provides some prefetch mechanisms to speed up commonly
cold cache line accesses during receive processing. Since these are
software structures it helps to have these strategically placed
prefetches.
Be careful to call BQL prefetch complete only for non XDP queues.
Co-developed-by: Piotr Raczynski <[email protected]>
Signed-off-by: Piotr Raczynski <[email protected]>
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Use the netif_tx_* API from netdevice.h which has simpler parameters.
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice hardware contains an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
In practical terms, activating the firmware does not always require a
full system reboot. In many cases it is possible to activate the EMP
firmware immediately. There are a couple of different scenarios to
cover.
* The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
* PCI configuration changes are only reloaded after a cold PCIe reset.
Unfortunately there is no generic way to trigger this for a PCIe
device without a system reboot.
When performing a flash update, firmware is capable of responding with
some information about the specific update requirements.
The driver updates the flash by programming a secondary inactive bank
with the contents of the new image, and then issuing a command to
request to switch the active bank starting from the next load.
The response to the final command for updating the inactive NVM flash
bank includes an indication of the minimum reset required to fully
update the device. This can be one of the following:
* A full power on is required
* A cold PCIe reset is required
* An EMP reset is required
The response to the command to switch flash banks includes an indication
of whether or not the firmware will allow an EMP reset request.
For most updates, an EMP reset is sufficient to load the new EMP
firmware without issues. In some cases, this reset is not sufficient
because the PCI configuration space has changed. When this could cause
incompatibility with the new EMP image, the firmware is capable of
rejecting the EMP reset request.
Add logic to ice_fw_update.c to handle the response data flash update
AdminQ commands.
For the reset level, issue a devlink status notification informing the
user of how to complete the update with a simple suggestion like
"Activate new firmware by rebooting the system".
Cache the status of whether or not firmware will restrict the EMP reset
for use in implementing devlink reload.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
For the .reload_down handler, we will issue a request for the EMP reset
using the appropriate firmware AdminQ command. If we know that the
firmware will not allow an EMP reset, simply exit with a suitable
netlink extended ACK message indicating that the EMP reset is not
available.
For the .reload_up handler, simply wait until the driver has finished
resetting. Logic to handle processing of an EMP reset already exists in
the driver as part of its reset and rebuild flows.
Implement support for the devlink reload interface with the
"fw_activate" action. This allows userspace to request activation of
firmware without a reboot.
Note that support for indicating the required reset and EMP reset
restriction is not supported on old versions of firmware. The driver can
determine if the two features are supported by checking the device
capabilities report. I confirmed support has existed since at least
version 5.5.2 as reported by the 'fw.mgmt' version. Support to issue the
EMP reset request has existed in all version of the EMP firmware for the
ice hardware.
Check the device capabilities report to determine whether or not the
indications are reported by the running firmware. If the reset
requirement indication is not supported, always assume a full power on
is necessary. If the reset restriction capability is not supported,
always assume the EMP reset is available.
Users can verify if the EMP reset has activated the firmware by using
the devlink info report to check that the 'running' firmware version has
updated. For example a user might do the following:
# Check current version
$ devlink dev info
# Update the device
$ devlink dev flash pci/0000:af:00.0 file firmware.bin
# Confirm stored version updated
$ devlink dev info
# Reload to activate new firmware
$ devlink dev reload pci/0000:af:00.0 action fw_activate
# Confirm running version updated
$ devlink dev info
Finally, this change does *not* implement basic driver-only reload
support. I did look into trying to do this. However, it requires
significant refactor of how the ice driver probes and loads everything.
The ice driver probe and allocation flows were not designed with such
a reload in mind. Refactoring the flow to support this is beyond the
scope of this change.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
During probe and device reset, the ice driver reads some data from the
NVM image as part of ice_init_nvm. Part of this data includes a section
of the Option ROM which contains version information.
The function ice_get_orom_civd_data is used to locate the '$CIV' data
section of the Option ROM.
Timing of ice_probe and ice_rebuild indicate that the
ice_get_orom_civd_data function takes about 10 seconds to finish
executing.
The function locates the section by scanning the Option ROM every 512
bytes. This requires a significant number of NVM read accesses, since
the Option ROM bank is 500KB. In the worst case it would take about 1000
reads. Worse, all PFs serialize this operation during reload because of
acquiring the NVM semaphore.
The CIVD section is located at the end of the Option ROM image data.
Unfortunately, the driver has no easy method to determine the offset
manually. Practical experiments have shown that the data could be at
a variety of locations, so simply reversing the scanning order is not
sufficient to reduce the overall read time.
Instead, copy the entire contents of the Option ROM into memory. This
allows reading the data using 4Kb pages instead of 512 bytes at a time.
This reduces the total number of firmware commands by a factor of 8. In
addition, reading the whole section together at once allows better
indication to firmware of when we're "done".
Re-write ice_get_orom_civd_data to allocate virtual memory to store the
Option ROM data. Copy the entire OptionROM contents at once using
ice_read_flash_module. Finally, use this memory copy to scan for the
'$CIV' section.
This change significantly reduces the time to read the Option ROM CIVD
section from ~10 seconds down to ~1 second. This has a significant
impact on the total time to complete a driver rebuild or probe.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice_devlink_flash_update function performs a few upfront checks and
then calls ice_flash_pldm_image.
Most if these checks make more sense in the context of code within
ice_flash_pldm_image. Merge ice_devlink_flash_update and
ice_flash_pldm_image into one function, placing it in ice_fw_update.c
Since this is still the entry point for devlink, call the function
ice_devlink_flash_update instead of ice_flash_pldm_image. This leaves a
single function which handles the devlink parameters and then initiates
a PLDM update.
With this change, the ice_devlink_flash_update function in
ice_fw_update.c becomes the main entry point for flash update. It
elimintes some unnecessary boiler plate code between the two previous
functions. The ultimate motivation for this is that it eases supporting
a dry run with the PLDM library in a future change.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice_devlink_flash_update function performs a few checks and then
calls ice_flash_pldm_image. One of these checks is to call
ice_check_for_pending_update. This function checks if the device has
a pending update, and cancels it if so. This is necessary to allow
a new flash update to proceed.
We want to refactor the ice code to eliminate ice_devlink_flash_update,
moving its checks into ice_flash_pldm_image.
To do this, ice_check_for_pending_update will become static, and only
called by ice_flash_pldm_image. To make this change easier to review,
first just move the function up within the ice_fw_update.c file.
While at it, note that the function has a misleading name. Its primary
action is to cancel a pending update. Using the verb "check" does not
imply this. Rename it to ice_cancel_pending_update.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
We have a region for reading the contents of the NVM flash as
a snapshot. This region does not allow reading the Shadow RAM, as it
always passes the FLASH_ONLY bit to the low level firmware interface.
Add a separate shadow-ram region which will allow snapshot of the
current contents of the Shadow RAM. This data is built from the NVM
contents but is distinct as the device builds up the Shadow RAM during
initialization, so being able to snapshot its contents can be useful
when attempting to debug flash related issues.
Fix the comment description of the nvm-flash region which incorrectly
stated that it filled the shadow-ram region, and add a comment
explaining that the nvm-flash region does not actually read the Shadow
RAM.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The driver has to check if it does not accidentally put the timestamp in
the SKB before previous timestamp gets overwritten.
Timestamp values in the PHY are read only and do not get cleared except
at hardware reset or when a new timestamp value is captured.
The cached_tstamp field is used to detect the case where a new timestamp
has not yet been captured, ensuring that we avoid sending stale
timestamp data to the stack.
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Karol Kolacinski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Change the division in ice_ptp_adjfine from div_u64 to div64_u64.
div_u64 is used when the divisor is 32 bit but in this case incval is
64 bit and it caused incorrect calculations and incval adjustments.
Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Karol Kolacinski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Remove the unused define ICE_FLOW_SEG_HDRS_L2_MASK.
Reported-by: Jesse Brandeburg <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
Acked-by: Paul Menzel <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
The "bitmap" variable is already an unsigned long so there is no need
for this cast.
Signed-off-by: Dan Carpenter <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
As all functions now return standard error codes, propagate the values
being returned instead of converting them to generic values.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
ice_status previously had a variable to contain these values where other
error codes had a variable as well. With ice_status now being an int,
there is no need for two variables to hold error values. In cases where
this occurs, remove one of the excess variables and use a single one.
Some initialization of variables are no longer needed and have been
removed.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
Clean up code after changing ice_status to int. Rearrange to fix reverse
Christmas tree and pull lines up where applicable.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
Replace uses of ice_status to, as equivalent as possible, error codes.
Remove enum ice_status and its helper conversion function as they are no
longer needed.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
To prepare for removal of ice_status, change the variables from
ice_status to int. This eases the transition when values are changed to
return standard int error codes over enum ice_status.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
Remove the ice_stat_str() function which prints the string
representation of the ice_status error code. With upcoming changes
moving away from ice_status, there will be no need for this function.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Gurucharan G <[email protected]>
|
|
Before this change, final state of the DDP pkg load process was
dependent on many variables such as: ice_status, pkg version,
ice_aq_err. The last one had be stored in hw->pkg_dwnld_status.
It was impossible to conclude this state just from ice_status, that's
why logging process of DDP pkg load in the caller was a little bit
complicated.
With this patch new status enum is introduced - ice_ddp_state.
It covers all the possible final states of the loading process.
What's tricky for ice_ddp_state is that not only
ICE_DDP_PKG_SUCCESS(=0) means that load was successful. Actually
three states mean that:
- ICE_DDP_PKG_SUCCESS
- ICE_DDP_PKG_SAME_VERSION_ALREADY_LOADED
- ICE_DDP_PKG_COMPATIBLE_ALREADY_LOADED
ice_is_init_pkg_successful can tell that information.
One ddp_state should not be used outside of ice_init_pkg which is
ICE_DDP_PKG_ALREADY_LOADED. It is more generic, it is used in
ice_dwnld_cfg_bufs to see if pkg is already loaded. At this point
we can't use one of the specific one (SAME_VERSION, COMPATIBLE,
NOT_SUPPORTED) because we don't have information on the package
currently loaded in HW (we are before calling ice_get_pkg_info).
We can get rid of hw->pkg_dwnld_status because we are immediately
mapping aq errors to ice_ddp_state in ice_dwnld_cfg_bufs.
Other errors like ICE_ERR_NO_MEMORY, ICE_ERR_PARAM are mapped the
generic ICE_DDP_PKG_ERR.
Suggested-by: Jacob Keller <[email protected]>
Signed-off-by: Wojciech Drewek <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Some of the promiscuous mode functions take a boolean to indicate
set/clear, which affects readability. Refactor and provide an
interface for the promiscuous mode code with explicit set and clear
promiscuous mode operations.
Signed-off-by: Brett Creeley <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Since the capability of a PTYPE within a specific package could be
negotiated by checking the HW bit map, it means that there's no need
to maintain a different PTYPE list for each type of the package when
parsing PTYPE. So refactor the PTYPE validating mechanism.
Signed-off-by: Jeff Guo <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Scan the 'Marker Ptype TCAM' section to retrieve the Rx parser PTYPE
enable information from the current package.
Signed-off-by: Haiyue Wang <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <[email protected]>
Signed-off-by: Hangbin Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
zero_copy_allocator has been removed back when Bjorn Topel introduced
xsk_buff_pool. Remove references to it that were dangling in the tree.
Signed-off-by: Maciej Fijalkowski <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Magnus Karlsson <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
In non trivial scenarios, the action id alone is not sufficient to
identify the program causing the warning. Before the previous patch,
the generated stack-trace pointed out at least the involved device
driver.
Let's additionally include the program name and id, and the relevant
device name.
If the user needs additional infos, he can fetch them via a kernel
probe, leveraging the arguments added here.
Signed-off-by: Paolo Abeni <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Toke Høiland-Jørgensen <[email protected]>
Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
|
|
The watchdog task incorrectly changes the state to __IAVF_RESETTING,
instead of letting the reset task take care of that. This was already
resolved by commit 22c8fd71d3a5 ("iavf: do not override the adapter
state in the watchdog task") but the problem was reintroduced by the
recent code refactoring in commit 45eebd62999d ("iavf: Refactor iavf
state machine tracking").
Fixes: 45eebd62999d ("iavf: Refactor iavf state machine tracking")
Signed-off-by: Stefan Assmann <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
This code was re-organized and there some unlocks missing now.
Fixes: 898ef1cb1cb2 ("iavf: Combine init and watchdog state machines")
Signed-off-by: Dan Carpenter <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The driver uses irq_set_affinity_hint() to update the affinity_hint mask
that is consumed by the userspace to distribute the interrupts. However,
under the hood irq_set_affinity_hint() also applies the provided cpumask
(if not NULL) as the affinity for the given interrupt which is an
undocumented side effect.
To remove this side effect irq_set_affinity_hint() has been marked
as deprecated and new interfaces have been introduced. Hence, replace the
irq_set_affinity_hint() with the new interface irq_update_affinity_hint()
that only updates the affinity_hint pointer.
Signed-off-by: Nitesh Narayan Lal <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: Jesse Brandeburg <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|