| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Replace uses of ice_status to, as equivalent as possible, error codes.
Remove enum ice_status and its helper conversion function as they are no
longer needed.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
|
|
Add a function to read the inactive netlist bank for version
information. To support this, refactor how we read the netlist version
data. Instead of using the firmware AQ interface with a module ID, read
from the flash as a flat NVM, using ice_read_flash_module.
This change requires a slight adjustment to the offset values used, as
reading from the flat NVM includes the type field (which was stripped by
firmware previously). Cleanup the macro names and move them to
ice_type.h. For clarity in how we calculate the offsets and so that
programmers can easily map the offset value to the data sheet, use
a wrapper macro to account for the offset adjustments.
Use the newly added ice_get_inactive_netlist_ver function to extract the
version data from the pending netlist module update. Add the stored
variants of "fw.netlist", and "fw.netlist.build" to the info version map
array.
With this change, we now report the "fw.netlist" and "fw.netlist.build"
versions into the stored section of the devlink info report. As with the
main NVM module versions, if there is no pending update, we report the
currently active values as stored.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
A race condition between FW and SW can occur between admin queue setup and
the first command sent. A link event may occur and FW attempts to notify a
non-existent queue. FW will set the critical error bit and disable the
queue. When this happens retry queue setup.
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Require the Dynamic Device Personalization (DDP) file to have the same
major version number and the same or older minor number than the firmware
version major and minor, respectively.
Check the OS and NVM package versions before downloading the package.
If the OS package version is not compatible with NVM then return an
appropriate error.
Split the 32-byte segment name into a 28-byte segment name and
a 4-byte Track-ID. Older packages will still work with this change
because no package has a name that will take up more than 28 bytes;
in this case the Track-ID will be 0.
Note that the driver will store the segment name as 32-bytes in the
ice_hw structure, in order to normalize the length of the various
package name strings that it uses.
Also add section ID and structure for the segment metadata section.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Store the TCAM entry with the profile data and the VSI group in the
respective SW structures. This will be subsequently used to write out
the tables to hardware.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a handler for ethtool selftest. Selftest includes
testing link, interrupts, eeprom, registers and packet loopback.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch introduces a new top level function ice_init_dcb (and
related lower level helper functions) which continues the DCB init
flow.
This function uses ice_get_dcb_cfg to get, parse and store the DCB
configuration. Once this is done, it sets itself up to be notified
by the firmware on LLDP MIB change events.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Check for a leaf node presence for a given VSI. This check is required
before removing a VSI since VSIs can't be removed with enabled queues
(with leaf nodes) from the FW scheduler tree unless its a reset.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Post VF initialization, there are a couple of different ways in which a
VF reset can be triggered. One is when the underlying PF itself goes
through a reset and other is via a VFLR interrupt. ice_reset_vf introduced
in this patch handles both these cases.
Also introduced in this patch is a helper function ice_aq_send_msg_to_vf
to send messages to VF over the mailbox queue. The PF uses this to send
reset notifications to VFs.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Once reset is issued, the driver loses all control queue interfaces.
Exercising control queue operations during reset is incorrect and
may result in long timeouts.
This patch introduces a new field 'reset_ongoing' in the hw structure.
This is set to 1 by the core driver when it receives a reset interrupt.
ice_sq_send_cmd checks reset_ongoing before actually issuing the control
queue operation. If a reset is in progress, it returns a soft error code
(ICE_ERR_RESET_PENDING) to the caller. The caller may or may not have to
take any action based on this return. Once the driver knows that the
reset is done, it has to set reset_ongoing back to 0. This will allow
control queue operations to be posted to the hardware again.
This "bail out" logic was specifically added to ice_sq_send_cmd (which
is pretty low level function) so that we have one solution in one place
that applies to all types of control queues.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch configures the VSIs to be able to send and receive
packets by doing the following:
1) Initialize flexible parser to extract and include certain
fields in the Rx descriptor.
2) Add Tx queues by programming the Tx queue context (implemented in
ice_vsi_cfg_txqs). Note that adding the queues also enables (starts)
the queues.
3) Add Rx queues by programming Rx queue context (implemented in
ice_vsi_cfg_rxqs). Note that this only adds queues but doesn't start
them. The rings will be started by calling ice_vsi_start_rx_rings on
interface up.
4) Configure interrupts for VSI queues.
5) Implement ice_open and ice_stop.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A VSI needs traffic directed towards it. This is done by programming
filter rules on the switch (embedded vSwitch) element in the hardware,
which connects the VSI to the ingress/egress port.
This patch introduces data structures and functions necessary to add
remove or update switch rules on the switch element. This is a pretty low
level function that is generic enough to add a whole range of filters.
This patch also introduces two top level functions ice_add_mac and
ice_remove mac which through a series of intermediate helper functions
eventually call ice_aq_sw_rules to add/delete simple MAC based filters.
It's worth noting that one invocation of ice_add_mac/ice_remove_mac
is capable of adding/deleting multiple MAC filters.
Also worth noting is the fact that the driver maintains a list of currently
active filters, so every filter addition/removal causes an update to this
list. This is done for a couple of reasons:
1) If two VSIs try to add the same filters, we need to detect it and do
things a little differently (i.e. use VSI lists, described below) as
the same filter can't be added more than once.
2) In the event of a hardware reset we can simply walk through this list
and restore the filters.
VSI Lists:
In a multi-VSI situation, it's possible that multiple VSIs want to add the
same filter rule. For example, two VSIs that want to receive broadcast
traffic would both add a filter for destination MAC ff:ff:ff:ff:ff:ff.
This can become cumbersome to maintain and so this is handled using a
VSI list.
A VSI list is resource that can be allocated in the hardware using the
ice_aq_alloc_free_res admin queue command. Simply put, a VSI list can
be thought of as a subscription list containing a set of VSIs to which
the packet should be forwarded, should the filter match.
For example, if VSI-0 has already added a broadcast filter, and VSI-1
wants to do the same thing, the filter creation flow will detect this,
allocate a VSI list and update the switch rule so that broadcast traffic
will now be forwarded to the VSI list which contains VSI-0 and VSI-1.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds code to continue the initialization flow as follows:
1) Get PHY/link information and store it
2) Get default scheduler tree topology and store it
3) Get the MAC address associated with the port and store it
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch implements multiple pieces of the initialization flow
as follows:
1) A reset is issued to ensure a clean device state, followed
by initialization of admin queue interface.
2) Once the admin queue interface is up, clear the PF config
and transition the device to non-PXE mode.
3) Get the NVM configuration stored in the device's non-volatile
memory (NVM) using ice_init_nvm.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A control queue is a hardware interface which is used by the driver
to interact with other subsystems (like firmware, PHY, etc.). It is
implemented as a producer-consumer ring. More specifically, an
"admin queue" is a type of control queue used to interact with the
firmware.
This patch introduces data structures and functions to initialize
and teardown control/admin queues. Once the admin queue is initialized,
the driver uses it to get the firmware version.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|