aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2024-07-26i3c: master: svc: resend target address when get NACKFrank Li1-14/+44
According to I3C Spec 1.1.1, 11-Jun-2021, section: 5.1.2.2.3: If the Controller chooses to start an I3C Message with an I3C Dynamic Address, then special provisions shall be made because that same I3C Target may be initiating an IBI or a Controller Role Request. So, one of three things may happen: (skip 1, 2) 3. The Addresses match and the RnW bits also match, and so neither Controller nor Target will ACK since both are expecting the other side to provide ACK. As a result, each side might think it had "won" arbitration, but neither side would continue, as each would subsequently see that the other did not provide ACK. ... For either value of RnW: Due to the NACK, the Controller shall defer the Private Write or Private Read, and should typically transmit the Target ^^^^^^^^^^^^^^^^^^^ Address again after a Repeated START (i.e., the next one or any one prior ^^^^^^^^^^^^^ to a STOP in the Frame). Since the Address Header following a Repeated START is not arbitrated, the Controller will always win (see Section 5.1.2.2.4). Resend target address again if address is not 7E and controller get NACK. Reviewed-by: Miquel Raynal <[email protected]> Signed-off-by: Frank Li <[email protected]> Signed-off-by: Alexandre Belloni <[email protected]>
2024-07-26Merge tag 'amd-drm-fixes-6.11-2024-07-25' of ↵Dave Airlie20-17/+261
https://gitlab.freedesktop.org/agd5f/linux into drm-next amd-drm-fixes-6.11-2024-07-25: amdgpu: - SDMA 5.2 workaround - GFX12 fixes - Uninitialized variable fix - VCN/JPEG 4.0.3 fixes - Misc display fixes - RAS fixes - VCN4/5 harvest fix - GPU reset fix Signed-off-by: Dave Airlie <[email protected]> From: Alex Deucher <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2024-07-26Merge tag 'drm-intel-next-fixes-2024-07-25' of ↵Dave Airlie2-7/+5
https://gitlab.freedesktop.org/drm/i915/kernel into drm-next - Do not consider preemption during execlists_dequeue for gen8 [gt] (Nitin Gote) - Allow NULL memory region (Jonathan Cavitt) Signed-off-by: Dave Airlie <[email protected]> From: Tvrtko Ursulin <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/ZqICQzyzm/6hDWy4@linux
2024-07-25Merge tag 'net-6.11-rc1' of ↵Linus Torvalds17-22/+84
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from bpf and netfilter. A lot of networking people were at a conference last week, busy catching COVID, so relatively short PR. Current release - regressions: - tcp: process the 3rd ACK with sk_socket for TFO and MPTCP Current release - new code bugs: - l2tp: protect session IDR and tunnel session list with one lock, make sure the state is coherent to avoid a warning - eth: bnxt_en: update xdp_rxq_info in queue restart logic - eth: airoha: fix location of the MBI_RX_AGE_SEL_MASK field Previous releases - regressions: - xsk: require XDP_UMEM_TX_METADATA_LEN to actuate tx_metadata_len, the field reuses previously un-validated pad Previous releases - always broken: - tap/tun: drop short frames to prevent crashes later in the stack - eth: ice: add a per-VF limit on number of FDIR filters - af_unix: disable MSG_OOB handling for sockets in sockmap/sockhash" * tag 'net-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (34 commits) tun: add missing verification for short frame tap: add missing verification for short frame mISDN: Fix a use after free in hfcmulti_tx() gve: Fix an edge case for TSO skb validity check bnxt_en: update xdp_rxq_info in queue restart logic tcp: process the 3rd ACK with sk_socket for TFO/MPTCP selftests/bpf: Add XDP_UMEM_TX_METADATA_LEN to XSK TX metadata test xsk: Require XDP_UMEM_TX_METADATA_LEN to actuate tx_metadata_len bpf: Fix a segment issue when downgrading gso_size net: mediatek: Fix potential NULL pointer dereference in dummy net_device handling MAINTAINERS: make Breno the netconsole maintainer MAINTAINERS: Update bonding entry net: nexthop: Initialize all fields in dumped nexthops net: stmmac: Correct byte order of perfect_match selftests: forwarding: skip if kernel not support setting bridge fdb learning limit tipc: Return non-zero value from tipc_udp_addr2str() on error netfilter: nft_set_pipapo_avx2: disable softinterrupts ice: Fix recipe read procedure ice: Add a per-VF limit on number of FDIR filters net: bonding: correctly annotate RCU in bond_should_notify_peers() ...
2024-07-25Merge tag 'printk-for-6.11-trivial' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux Pull printk updates from Petr Mladek: - trivial printk changes The bigger "real" printk work is still being discussed. * tag 'printk-for-6.11-trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: vsprintf: add missing MODULE_DESCRIPTION() macro printk: Rename console_replay_all() and update context
2024-07-25Merge tag 'constfy-sysctl-6.11-rc1' of ↵Linus Torvalds7-14/+14
git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl Pull sysctl constification from Joel Granados: "Treewide constification of the ctl_table argument of proc_handlers using a coccinelle script and some manual code formatting fixups. This is a prerequisite to moving the static ctl_table structs into read-only data section which will ensure that proc_handler function pointers cannot be modified" * tag 'constfy-sysctl-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl: sysctl: treewide: constify the ctl_table argument of proc_handlers
2024-07-25Merge tag 'efi-fixes-for-v6.11-1' of ↵Linus Torvalds2-5/+17
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi Pull EFI fixes from Ard Biesheuvel: - Wipe screen_info after allocating it from the heap - used by arm32 and EFI zboot, other EFI architectures allocate it statically - Revert to allocating boot_params from the heap on x86 when entering via the native PE entrypoint, to work around a regression on older Dell hardware * tag 'efi-fixes-for-v6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi: x86/efistub: Revert to heap allocated boot_params for PE entrypoint efi/libstub: Zero initialize heap allocated struct screen_info
2024-07-25Merge tag 'driver-core-6.11-rc1' of ↵Linus Torvalds143-462/+423
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here is the big set of driver core changes for 6.11-rc1. Lots of stuff in here, with not a huge diffstat, but apis are evolving which required lots of files to be touched. Highlights of the changes in here are: - platform remove callback api final fixups (Uwe took many releases to get here, finally!) - Rust bindings for basic firmware apis and initial driver-core interactions. It's not all that useful for a "write a whole driver in rust" type of thing, but the firmware bindings do help out the phy rust drivers, and the driver core bindings give a solid base on which others can start their work. There is still a long way to go here before we have a multitude of rust drivers being added, but it's a great first step. - driver core const api changes. This reached across all bus types, and there are some fix-ups for some not-common bus types that linux-next and 0-day testing shook out. This work is being done to help make the rust bindings more safe, as well as the C code, moving toward the end-goal of allowing us to put driver structures into read-only memory. We aren't there yet, but are getting closer. - minor devres cleanups and fixes found by code inspection - arch_topology minor changes - other minor driver core cleanups All of these have been in linux-next for a very long time with no reported problems" * tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits) ARM: sa1100: make match function take a const pointer sysfs/cpu: Make crash_hotplug attribute world-readable dio: Have dio_bus_match() callback take a const * zorro: make match function take a const pointer driver core: module: make module_[add|remove]_driver take a const * driver core: make driver_find_device() take a const * driver core: make driver_[create|remove]_file take a const * firmware_loader: fix soundness issue in `request_internal` firmware_loader: annotate doctests as `no_run` devres: Correct code style for functions that return a pointer type devres: Initialize an uninitialized struct member devres: Fix memory leakage caused by driver API devm_free_percpu() devres: Fix devm_krealloc() wasting memory driver core: platform: Switch to use kmemdup_array() driver core: have match() callback in struct bus_type take a const * MAINTAINERS: add Rust device abstractions to DRIVER CORE device: rust: improve safety comments MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER firmware: rust: improve safety comments ...
2024-07-25Merge tag 'linux-watchdog-6.11-rc1' of ↵Linus Torvalds7-58/+79
git://www.linux-watchdog.org/linux-watchdog Pull watchdog updates from Wim Van Sebroeck: - make watchdog_class const - rework of the rzg2l_wdt driver - other small fixes and improvements * tag 'linux-watchdog-6.11-rc1' of git://www.linux-watchdog.org/linux-watchdog: dt-bindings: watchdog: dlg,da9062-watchdog: Drop blank space watchdog: rzn1: Convert comma to semicolon watchdog: lenovo_se10_wdt: Convert comma to semicolon dt-bindings: watchdog: renesas,wdt: Document RZ/G3S support watchdog: rzg2l_wdt: Add suspend/resume support watchdog: rzg2l_wdt: Rely on the reset driver for doing proper reset watchdog: rzg2l_wdt: Remove comparison with zero watchdog: rzg2l_wdt: Remove reset de-assert from probe watchdog: rzg2l_wdt: Check return status of pm_runtime_put() watchdog: rzg2l_wdt: Use pm_runtime_resume_and_get() watchdog: rzg2l_wdt: Make the driver depend on PM watchdog: rzg2l_wdt: Restrict the driver to ARCH_RZG2L and ARCH_R9A09G011 watchdog: imx7ulp_wdt: keep already running watchdog enabled watchdog: starfive: Add missing clk_disable_unprepare() watchdog: Make watchdog_class const
2024-07-25tun: add missing verification for short frameDongli Zhang1-0/+3
The cited commit missed to check against the validity of the frame length in the tun_xdp_one() path, which could cause a corrupted skb to be sent downstack. Even before the skb is transmitted, the tun_xdp_one-->eth_type_trans() may access the Ethernet header although it can be less than ETH_HLEN. Once transmitted, this could either cause out-of-bound access beyond the actual length, or confuse the underlayer with incorrect or inconsistent header length in the skb metadata. In the alternative path, tun_get_user() already prohibits short frame which has the length less than Ethernet header size from being transmitted for IFF_TAP. This is to drop any frame shorter than the Ethernet header size just like how tun_get_user() does. CVE: CVE-2024-41091 Inspired-by: https://lore.kernel.org/netdev/[email protected]/ Fixes: 043d222f93ab ("tuntap: accept an array of XDP buffs through sendmsg()") Cc: [email protected] Signed-off-by: Dongli Zhang <[email protected]> Reviewed-by: Si-Wei Liu <[email protected]> Reviewed-by: Willem de Bruijn <[email protected]> Reviewed-by: Paolo Abeni <[email protected]> Reviewed-by: Jason Wang <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-07-25tap: add missing verification for short frameSi-Wei Liu1-0/+5
The cited commit missed to check against the validity of the frame length in the tap_get_user_xdp() path, which could cause a corrupted skb to be sent downstack. Even before the skb is transmitted, the tap_get_user_xdp()-->skb_set_network_header() may assume the size is more than ETH_HLEN. Once transmitted, this could either cause out-of-bound access beyond the actual length, or confuse the underlayer with incorrect or inconsistent header length in the skb metadata. In the alternative path, tap_get_user() already prohibits short frame which has the length less than Ethernet header size from being transmitted. This is to drop any frame shorter than the Ethernet header size just like how tap_get_user() does. CVE: CVE-2024-41090 Link: https://lore.kernel.org/netdev/[email protected]/ Fixes: 0efac27791ee ("tap: accept an array of XDP buffs through sendmsg()") Cc: [email protected] Signed-off-by: Si-Wei Liu <[email protected]> Signed-off-by: Dongli Zhang <[email protected]> Reviewed-by: Willem de Bruijn <[email protected]> Reviewed-by: Paolo Abeni <[email protected]> Reviewed-by: Jason Wang <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-07-25mISDN: Fix a use after free in hfcmulti_tx()Dan Carpenter1-3/+4
Don't dereference *sp after calling dev_kfree_skb(*sp). Fixes: af69fb3a8ffa ("Add mISDN HFC multiport driver") Signed-off-by: Dan Carpenter <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-07-25gve: Fix an edge case for TSO skb validity checkBailey Forrest1-1/+21
The NIC requires each TSO segment to not span more than 10 descriptors. NIC further requires each descriptor to not exceed 16KB - 1 (GVE_TX_MAX_BUF_SIZE_DQO). The descriptors for an skb are generated by gve_tx_add_skb_no_copy_dqo() for DQO RDA queue format. gve_tx_add_skb_no_copy_dqo() loops through each skb frag and generates a descriptor for the entire frag if the frag size is not greater than GVE_TX_MAX_BUF_SIZE_DQO. If the frag size is greater than GVE_TX_MAX_BUF_SIZE_DQO, it is split into descriptor(s) of size GVE_TX_MAX_BUF_SIZE_DQO and a descriptor is generated for the remainder (frag size % GVE_TX_MAX_BUF_SIZE_DQO). gve_can_send_tso() checks if the descriptors thus generated for an skb would meet the requirement that each TSO-segment not span more than 10 descriptors. However, the current code misses an edge case when a TSO segment spans multiple descriptors within a large frag. This change fixes the edge case. gve_can_send_tso() relies on the assumption that max gso size (9728) is less than GVE_TX_MAX_BUF_SIZE_DQO and therefore within an skb fragment a TSO segment can never span more than 2 descriptors. Fixes: a57e5de476be ("gve: DQO: Add TX path") Signed-off-by: Praveen Kaligineedi <[email protected]> Signed-off-by: Bailey Forrest <[email protected]> Reviewed-by: Jeroen de Borst <[email protected]> Cc: [email protected] Reviewed-by: Willem de Bruijn <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-07-25bnxt_en: update xdp_rxq_info in queue restart logicTaehee Yoo1-0/+17
When the netdev_rx_queue_restart() restarts queues, the bnxt_en driver updates(creates and deletes) a page_pool. But it doesn't update xdp_rxq_info, so the xdp_rxq_info is still connected to an old page_pool. So, bnxt_rx_ring_info->page_pool indicates a new page_pool, but bnxt_rx_ring_info->xdp_rxq is still connected to an old page_pool. An old page_pool is no longer used so it is supposed to be deleted by page_pool_destroy() but it isn't. Because the xdp_rxq_info is holding the reference count for it and the xdp_rxq_info is not updated, an old page_pool will not be deleted in the queue restart logic. Before restarting 1 queue: ./tools/net/ynl/samples/page-pool enp10s0f1np1[6] page pools: 4 (zombies: 0) refs: 8192 bytes: 33554432 (refs: 0 bytes: 0) recycling: 0.0% (alloc: 128:8048 recycle: 0:0) After restarting 1 queue: ./tools/net/ynl/samples/page-pool enp10s0f1np1[6] page pools: 5 (zombies: 0) refs: 10240 bytes: 41943040 (refs: 0 bytes: 0) recycling: 20.0% (alloc: 160:10080 recycle: 1920:128) Before restarting queues, an interface has 4 page_pools. After restarting one queue, an interface has 5 page_pools, but it should be 4, not 5. The reason is that queue restarting logic creates a new page_pool and an old page_pool is not deleted due to the absence of an update of xdp_rxq_info logic. Fixes: 2d694c27d32e ("bnxt_en: implement netdev_queue_mgmt_ops") Signed-off-by: Taehee Yoo <[email protected]> Reviewed-by: David Wei <[email protected]> Reviewed-by: Somnath Kotur <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2024-07-25nvme-pci: add missing condition check for existence of mapped dataLeon Romanovsky1-1/+2
nvme_map_data() is called when request has physical segments, hence the nvme_unmap_data() should have same condition to avoid dereference. Fixes: 4aedb705437f ("nvme-pci: split metadata handling from nvme_map_data / nvme_unmap_data") Signed-off-by: Leon Romanovsky <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Reviewed-by: Nitesh Shetty <[email protected]> Signed-off-by: Keith Busch <[email protected]>
2024-07-25iommu: arm-smmu: Fix Tegra workaround for PAGE_SIZE mappingsAshish Mhetre1-1/+1
PAGE_SIZE can be 16KB for Tegra which is not supported by MMU-500 on both Tegra194 and Tegra234. Retain only valid granularities from pgsize_bitmap which would either be 4KB or 64KB. Signed-off-by: Ashish Mhetre <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Will Deacon <[email protected]>
2024-07-25of: remove internal arguments from of_property_for_each_u32()Luca Ceresoli18-73/+47
The of_property_for_each_u32() macro needs five parameters, two of which are primarily meant as internal variables for the macro itself (in the for() clause). Yet these two parameters are used by a few drivers, and this can be considered misuse or at least bad practice. Now that the kernel uses C11 to build, these two parameters can be avoided by declaring them internally, thus changing this pattern: struct property *prop; const __be32 *p; u32 val; of_property_for_each_u32(np, "xyz", prop, p, val) { ... } to this: u32 val; of_property_for_each_u32(np, "xyz", val) { ... } However two variables cannot be declared in the for clause even with C11, so declare one struct that contain the two variables we actually need. As the variables inside this struct are not meant to be used by users of this macro, give the struct instance the noticeable name "_it" so it is visible during code reviews, helping to avoid new code to use it directly. Most usages are trivially converted as they do not use those two parameters, as expected. The non-trivial cases are: - drivers/clk/clk.c, of_clk_get_parent_name(): easily doable anyway - drivers/clk/clk-si5351.c, si5351_dt_parse(): this is more complex as the checks had to be replicated in a different way, making code more verbose and somewhat uglier, but I refrained from a full rework to keep as much of the original code untouched having no hardware to test my changes All the changes have been build tested. The few for which I have the hardware have been runtime-tested too. Reviewed-by: Andre Przywara <[email protected]> # drivers/clk/sunxi/clk-simple-gates.c, drivers/clk/sunxi/clk-sun8i-bus-gates.c Acked-by: Bartosz Golaszewski <[email protected]> # drivers/gpio/gpio-brcmstb.c Acked-by: Nicolas Ferre <[email protected]> # drivers/irqchip/irq-atmel-aic-common.c Acked-by: Jonathan Cameron <[email protected]> # drivers/iio/adc/ti_am335x_adc.c Acked-by: Uwe Kleine-König <[email protected]> # drivers/pwm/pwm-samsung.c Acked-by: Richard Leitner <[email protected]> # drivers/usb/misc/usb251xb.c Acked-by: Mark Brown <[email protected]> # sound/soc/codecs/arizona.c Reviewed-by: Richard Fitzgerald <[email protected]> # sound/soc/codecs/arizona.c Acked-by: Michael Ellerman <[email protected]> # arch/powerpc/sysdev/xive/spapr.c Acked-by: Stephen Boyd <[email protected]> # clk Signed-off-by: Luca Ceresoli <[email protected]> Acked-by: Lee Jones <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Rob Herring (Arm) <[email protected]>
2024-07-25rbd: don't assume rbd_is_lock_owner() for exclusive mappingsIlya Dryomov1-5/+0
Expanding on the previous commit, assuming that rbd_is_lock_owner() always returns true (i.e. that we are either in RBD_LOCK_STATE_LOCKED or RBD_LOCK_STATE_QUIESCING) if the mapping is exclusive is wrong too. In case ceph_cls_set_cookie() fails, the lock would be temporarily released even if the mapping is exclusive, meaning that we can end up even in RBD_LOCK_STATE_UNLOCKED. IOW, exclusive mappings are really "just" about disabling automatic lock transitions (as documented in the man page), not about grabbing the lock and holding on to it whatever it takes. Cc: [email protected] Fixes: 637cd060537d ("rbd: new exclusive lock wait/wake code") Signed-off-by: Ilya Dryomov <[email protected]> Reviewed-by: Dongsheng Yang <[email protected]>
2024-07-25rbd: don't assume RBD_LOCK_STATE_LOCKED for exclusive mappingsIlya Dryomov1-5/+5
Every time a watch is reestablished after getting lost, we need to update the cookie which involves quiescing exclusive lock. For this, we transition from RBD_LOCK_STATE_LOCKED to RBD_LOCK_STATE_QUIESCING roughly for the duration of rbd_reacquire_lock() call. If the mapping is exclusive and I/O happens to arrive in this time window, it's failed with EROFS (later translated to EIO) based on the wrong assumption in rbd_img_exclusive_lock() -- "lock got released?" check there stopped making sense with commit a2b1da09793d ("rbd: lock should be quiesced on reacquire"). To make it worse, any such I/O is added to the acquiring list before EROFS is returned and this sets up for violating rbd_lock_del_request() precondition that the request is either on the running list or not on any list at all -- see commit ded080c86b3f ("rbd: don't move requests to the running list on errors"). rbd_lock_del_request() ends up processing these requests as if they were on the running list which screws up quiescing_wait completion counter and ultimately leads to rbd_assert(!completion_done(&rbd_dev->quiescing_wait)); being triggered on the next watch error. Cc: [email protected] # 06ef84c4e9c4: rbd: rename RBD_LOCK_STATE_RELEASING and releasing_wait Cc: [email protected] Fixes: 637cd060537d ("rbd: new exclusive lock wait/wake code") Signed-off-by: Ilya Dryomov <[email protected]> Reviewed-by: Dongsheng Yang <[email protected]>
2024-07-25rbd: rename RBD_LOCK_STATE_RELEASING and releasing_waitIlya Dryomov1-10/+10
... to RBD_LOCK_STATE_QUIESCING and quiescing_wait to recognize that this state and the associated completion are backing rbd_quiesce_lock(), which isn't specific to releasing the lock. While exclusive lock does get quiesced before it's released, it also gets quiesced before an attempt to update the cookie is made and there the lock is not released as long as ceph_cls_set_cookie() succeeds. Signed-off-by: Ilya Dryomov <[email protected]> Reviewed-by: Dongsheng Yang <[email protected]>
2024-07-25net: mediatek: Fix potential NULL pointer dereference in dummy net_device ↵Breno Leitao1-2/+1
handling Move the freeing of the dummy net_device from mtk_free_dev() to mtk_remove(). Previously, if alloc_netdev_dummy() failed in mtk_probe(), eth->dummy_dev would be NULL. The error path would then call mtk_free_dev(), which in turn called free_netdev() assuming dummy_dev was allocated (but it was not), potentially causing a NULL pointer dereference. By moving free_netdev() to mtk_remove(), we ensure it's only called when mtk_probe() has succeeded and dummy_dev is fully allocated. This addresses a potential NULL pointer dereference detected by Smatch[1]. Fixes: b209bd6d0bff ("net: mediatek: mtk_eth_sock: allocate dummy net_device dynamically") Reported-by: Dan Carpenter <[email protected]> Closes: https://lore.kernel.org/all/[email protected]/ [1] Suggested-by: Dan Carpenter <[email protected]> Reviewed-by: Dan Carpenter <[email protected]> Signed-off-by: Breno Leitao <[email protected]> Reviewed-by: Simon Horman <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Paolo Abeni <[email protected]>
2024-07-25Merge branch '100GbE' of ↵Paolo Abeni5-5/+25
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== This series contains updates to ice driver only. Ahmed enforces the iavf per VF filter limit on ice (PF) driver to prevent possible resource exhaustion. Wojciech corrects assignment of l2 flags read from firmware. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: Fix recipe read procedure ice: Add a per-VF limit on number of FDIR filters ==================== Link: https://patch.msgid.link/[email protected] Signed-off-by: Paolo Abeni <[email protected]>
2024-07-24drm/amdgpu: reset vm state machine after gpu reset(vram lost)ZhenGuo Yin1-4/+5
[Why] Page table of compute VM in the VRAM will lost after gpu reset. VRAM won't be restored since compute VM has no shadows. [How] Use higher 32-bit of vm->generation to record a vram_lost_counter. Reset the VM state machine when vm->genertaion is not equal to the new generation token. v2: Check vm->generation instead of calling drm_sched_entity_error in amdgpu_vm_validate. v3: Use new generation token instead of vram_lost_counter for check. Signed-off-by: ZhenGuo Yin <[email protected]> Reviewed-by: Christian König <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected] (cherry picked from commit 47c0388b0589cb481c294dcb857d25a214c46eb3)
2024-07-24drm/amdgpu: add missed harvest check for VCN IP v4/v5Tim Huang3-0/+18
To prevent below probe failure, add a check for models with VCN IP v4.0.6 where VCN1 may be harvested. v2: Apply the same check to VCN IP v4.0 and v5.0. [ 54.070117] RIP: 0010:vcn_v4_0_5_start_dpg_mode+0x9be/0x36b0 [amdgpu] [ 54.071055] Code: 80 fb ff 8d 82 00 80 fe ff 81 fe 00 06 00 00 0f 43 c2 49 69 d5 38 0d 00 00 48 8d 71 04 c1 e8 02 4c 01 f2 48 89 b2 50 f6 02 00 <89> 01 48 8b 82 50 f6 02 00 48 8d 48 04 48 89 8a 50 f6 02 00 c7 00 [ 54.072408] RSP: 0018:ffffb17985f736f8 EFLAGS: 00010286 [ 54.072793] RAX: 00000000000000d6 RBX: ffff99a82f680000 RCX: 0000000000000000 [ 54.073315] RDX: ffff99a82f680000 RSI: 0000000000000004 RDI: ffff99a82f680000 [ 54.073835] RBP: ffffb17985f73730 R08: 0000000000000001 R09: 0000000000000000 [ 54.074353] R10: 0000000000000008 R11: ffffb17983c05000 R12: 0000000000000000 [ 54.074879] R13: 0000000000000000 R14: ffff99a82f680000 R15: 0000000000000001 [ 54.075400] FS: 00007f8d9c79a000(0000) GS:ffff99ab2f140000(0000) knlGS:0000000000000000 [ 54.075988] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 54.076408] CR2: 0000000000000000 CR3: 0000000140c3a000 CR4: 0000000000750ef0 [ 54.076927] PKRU: 55555554 [ 54.077132] Call Trace: [ 54.077319] <TASK> [ 54.077484] ? show_regs+0x69/0x80 [ 54.077747] ? __die+0x28/0x70 [ 54.077979] ? page_fault_oops+0x180/0x4b0 [ 54.078286] ? do_user_addr_fault+0x2d2/0x680 [ 54.078610] ? exc_page_fault+0x84/0x190 [ 54.078910] ? asm_exc_page_fault+0x2b/0x30 [ 54.079224] ? vcn_v4_0_5_start_dpg_mode+0x9be/0x36b0 [amdgpu] [ 54.079941] ? vcn_v4_0_5_start_dpg_mode+0xe6/0x36b0 [amdgpu] [ 54.080617] vcn_v4_0_5_set_powergating_state+0x82/0x19b0 [amdgpu] [ 54.081316] amdgpu_device_ip_set_powergating_state+0x64/0xc0 [amdgpu] [ 54.082057] amdgpu_vcn_ring_begin_use+0x6f/0x1d0 [amdgpu] [ 54.082727] amdgpu_ring_alloc+0x44/0x70 [amdgpu] [ 54.083351] amdgpu_vcn_dec_sw_ring_test_ring+0x40/0x110 [amdgpu] [ 54.084054] amdgpu_ring_test_helper+0x22/0x90 [amdgpu] [ 54.084698] vcn_v4_0_5_hw_init+0x87/0xc0 [amdgpu] [ 54.085307] amdgpu_device_init+0x1f96/0x2780 [amdgpu] [ 54.085951] amdgpu_driver_load_kms+0x1e/0xc0 [amdgpu] [ 54.086591] amdgpu_pci_probe+0x19f/0x550 [amdgpu] [ 54.087215] local_pci_probe+0x48/0xa0 [ 54.087509] pci_device_probe+0xc9/0x250 [ 54.087812] really_probe+0x1a4/0x3f0 [ 54.088101] __driver_probe_device+0x7d/0x170 [ 54.088443] driver_probe_device+0x24/0xa0 [ 54.088765] __driver_attach+0xdd/0x1d0 [ 54.089068] ? __pfx___driver_attach+0x10/0x10 [ 54.089417] bus_for_each_dev+0x8e/0xe0 [ 54.089718] driver_attach+0x22/0x30 [ 54.090000] bus_add_driver+0x120/0x220 [ 54.090303] driver_register+0x62/0x120 [ 54.090606] ? __pfx_amdgpu_init+0x10/0x10 [amdgpu] [ 54.091255] __pci_register_driver+0x62/0x70 [ 54.091593] amdgpu_init+0x67/0xff0 [amdgpu] [ 54.092190] do_one_initcall+0x5f/0x330 [ 54.092495] do_init_module+0x68/0x240 [ 54.092794] load_module+0x201c/0x2110 [ 54.093093] init_module_from_file+0x97/0xd0 [ 54.093428] ? init_module_from_file+0x97/0xd0 [ 54.093777] idempotent_init_module+0x11c/0x2a0 [ 54.094134] __x64_sys_finit_module+0x64/0xc0 [ 54.094476] do_syscall_64+0x58/0x120 [ 54.094767] entry_SYSCALL_64_after_hwframe+0x6e/0x76 Signed-off-by: Tim Huang <[email protected]> Reviewed-by: Saleemkhan Jamadar <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected] (cherry picked from commit 0b071245ddd98539d4f7493bdd188417fcf2d629)
2024-07-24drm/amdgpu: Fix eeprom max record countStanley.Yang1-0/+3
The eeprom table is empty before initializing, set eeprom table version first before initializing. Changed from V1: Reuse amdgpu_ras_set_eeprom_table_version function Signed-off-by: Stanley.Yang <[email protected]> Reviewed-by: Hawking Zhang <[email protected]> Signed-off-by: Alex Deucher <[email protected]> (cherry picked from commit 015b8a2fdf39a4c288ff24e7b715b8d9198e56dc)
2024-07-24drm/amdgpu: fix ras UE error injection failure issueYiPeng Chai1-3/+1
The ras command shared memory is allocated from VRAM and the response status of the command buffer will not be zero due to gpu being in fatal error state after ras UE error injection. Signed-off-by: YiPeng Chai <[email protected]> Reviewed-by: Hawking Zhang <[email protected]> Signed-off-by: Alex Deucher <[email protected]> (cherry picked from commit 8284951a6e79c6806c675e5f68a4cd425dd56bc4)
2024-07-24drm/amd/display: Remove ASSERT if significance is zero in math_ceil2Rodrigo Siqueira1-2/+0
In the DML math_ceil2 function, there is one ASSERT if the significance is equal to zero. However, significance might be equal to zero sometimes, and this is not an issue for a ceil function, but the current ASSERT will trigger warnings in those cases. This commit removes the ASSERT if the significance is equal to zero to avoid unnecessary noise. Cc: Mario Limonciello <[email protected]> Cc: Alex Deucher <[email protected]> Cc: [email protected] Reviewed-by: Chaitanya Dhere <[email protected]> Signed-off-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Aurabindo Pillai <[email protected]> Signed-off-by: Alex Deucher <[email protected]> (cherry picked from commit 332315885d3ccc6d8fe99700f3c2e4c24aa65ab7)
2024-07-24drm/amd/display: Check for NULL pointerSung Joon Kim1-1/+2
[why & how] Need to make sure plane_state is initialized before accessing its members. Cc: Mario Limonciello <[email protected]> Cc: Alex Deucher <[email protected]> Cc: [email protected] Reviewed-by: Xi (Alex) Liu <[email protected]> Signed-off-by: Sung Joon Kim <[email protected]> Signed-off-by: Aurabindo Pillai <[email protected]> Signed-off-by: Alex Deucher <[email protected]> (cherry picked from commit 295d91cbc700651782a60572f83c24861607b648)
2024-07-24drm/amdgpu/vcn: Use offsets local to VCN/JPEG in VFJane Jian2-5/+60
For VCN/JPEG 4.0.3, use only the local addressing scheme. - Mask bit higher than AID0 range v2 remain the case for mmhub use master XCC Signed-off-by: Jane Jian <[email protected]> Reviewed-by: Lijo Lazar <[email protected]> Signed-off-by: Alex Deucher <[email protected]> (cherry picked from commit caaf576292f8ccef5cdc0ac16e77b87dbf6e17ab)
2024-07-24drm/amdgpu: Add empty HDP flush function to VCN v4.0.3Lijo Lazar1-0/+8
VCN 4.0.3 does not HDP flush with RRMT enabled. Instead, mmsch will do the HDP flush. This change is necessary for VCN v4.0.3, no need for backward compatibility Signed-off-by: Lijo Lazar <[email protected]> Signed-off-by: Jane Jian <[email protected]> Reviewed-by: Hawking Zhang <[email protected]> Signed-off-by: Alex Deucher <[email protected]> (cherry picked from commit 49cfaebe48e97500a68d5322a8194736b0a2c3cf)
2024-07-24drm/amdgpu: Add empty HDP flush function to JPEG v4.0.3Lijo Lazar1-0/+8
JPEG v4.0.3 doesn't support HDP flush when RRMT is enabled. Instead, mmsch fw will do the flush. This change is necessary for JPEG v4.0.3, no need for backward compatibility Signed-off-by: Lijo Lazar <[email protected]> Signed-off-by: Jane Jian <[email protected]> Reviewed-by: Hawking Zhang <[email protected]> Signed-off-by: Alex Deucher <[email protected]> (cherry picked from commit 585e3fdb36f59c5cfed0ae06c852dc1df22b1d60)
2024-07-24drm/amd/amdgpu: Fix uninitialized variable warningsMa Ke1-1/+1
Return 0 to avoid returning an uninitialized variable r. Cc: [email protected] Fixes: 230dd6bb6117 ("drm/amd/amdgpu: implement mode2 reset on smu_v13_0_10") Signed-off-by: Ma Ke <[email protected]> Signed-off-by: Alex Deucher <[email protected]> (cherry picked from commit 6472de66c0aa18d50a4b5ca85f8272e88a737676)
2024-07-24drm/amdgpu: Fix atomics on GFX12David Belanger8-1/+143
If PCIe supports atomics, configure register to prevent DF from breaking atomics in separate load/store operations. Signed-off-by: David Belanger <[email protected]> Reviewed-by: Hawking Zhang <[email protected]> Signed-off-by: Alex Deucher <[email protected]> (cherry picked from commit 666f14cab21b17ccc1bdfe1e82458aa429b3b7e0)
2024-07-24drm/amdgpu/sdma5.2: Update wptr registers as well as doorbellAlex Deucher1-0/+12
We seem to have a case where SDMA will sometimes miss a doorbell if GFX is entering the powergating state when the doorbell comes in. To workaround this, we can update the wptr via MMIO, however, this is only safe because we disallow gfxoff in begin_ring() for SDMA 5.2 and then allow it again in end_ring(). Enable this workaround while we are root causing the issue with the HW team. Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/3440 Tested-by: Friedrich Vock <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected] (cherry picked from commit f2ac52634963fc38e4935e11077b6f7854e5d700)
2024-07-24Merge tag 'phy-for-6.11' of ↵Linus Torvalds26-397/+4435
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy Pull phy updates from Vinod Koul: "New Support - Samsung Exynos gs101 drd combo phy - Qualcomm SC8180x USB uniphy, IPQ9574 QMP PCIe phy - Airoha EN7581 PCIe phy - Freescale i.MX8Q HSIO SerDes phy - Starfive jh7110 dphy tx Updates: - Resume support for j721e-wiz driver - Updates to Exynos usbdrd driver - Support for optional power domains in g12a usb2-phy driver - Debugfs support and updates to zynqmp driver" * tag 'phy-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (56 commits) phy: airoha: Add dtime and Rx AEQ IO registers dt-bindings: phy: airoha: Add dtime and Rx AEQ IO registers dt-bindings: phy: rockchip-emmc-phy: Convert to dtschema dt-bindings: phy: qcom,qmp-usb: fix spelling error phy: exynos5-usbdrd: support Exynos USBDRD 3.1 combo phy (HS & SS) phy: exynos5-usbdrd: convert Vbus supplies to regulator_bulk phy: exynos5-usbdrd: convert (phy) register access clock to clk_bulk phy: exynos5-usbdrd: convert core clocks to clk_bulk phy: exynos5-usbdrd: support isolating HS and SS ports independently dt-bindings: phy: samsung,usb3-drd-phy: add gs101 compatible phy: core: Fix documentation of of_phy_get phy: starfive: Correct the dphy configure process phy: zynqmp: Add debugfs support phy: zynqmp: Take the phy mutex in xlate phy: zynqmp: Only wait for PLL lock "primary" instances phy: zynqmp: Store instance instead of type phy: zynqmp: Enable reference clock correctly phy: cadence-torrent: Check return value on register read phy: Fix the cacography in phy-exynos5250-usb2.c phy: phy-rockchip-samsung-hdptx: Select CONFIG_MFD_SYSCON ...
2024-07-24Merge tag 'soundwire-6.11-rc1' of ↵Linus Torvalds14-80/+264
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire Pull soundwire updates from Vinod Koul: - Simplification across subsystem using cleanup.h - Support for debugfs to read/write commands - Few Intel and Qualcomm driver updates * tag 'soundwire-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: soundwire: debugfs: simplify with cleanup.h soundwire: cadence: simplify with cleanup.h soundwire: intel_ace2x: simplify with cleanup.h soundwire: intel_ace2x: simplify return path in hw_params soundwire: intel: simplify with cleanup.h soundwire: intel: simplify return path in hw_params soundwire: amd_init: simplify with cleanup.h soundwire: amd: simplify with cleanup.h soundwire: amd: simplify return path in hw_params soundwire: intel_auxdevice: start the bus at default frequency soundwire: intel_auxdevice: add cs42l43 codec to wake_capable_list drivers:soundwire: qcom: cleanup port maask calculations soundwire: bus: simplify by using local slave->prop soundwire: generic_bandwidth_allocation: change port_bo parameter to pointer soundwire: Intel: clarify Copyright information soundwire: intel_ace2.x: add AC timing extensions for PantherLake soundwire: bus: add stream refcount soundwire: debugfs: add interface to read/write commands
2024-07-24Merge tag 'dmaengine-6.11-rc1' of ↵Linus Torvalds32-122/+2047
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine Pull dmaengine updates from Vinod Koul: "New support: - New dmaengine_prep_peripheral_dma_vec() to support transfers using dma vectors and documentation and user in AXI dma - STMicro STM32 DMA3 support and new capabilities of cyclic dma Updates: - Yaml conversion for Freescale imx dma and qdma bindings, sprd sc9860 dma binding - Altera msgdma updates for descriptor management" * tag 'dmaengine-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (35 commits) dt-bindings: fsl-qdma: fix interrupts 'if' check logic dt-bindings: dma: sprd,sc9860-dma: convert to YAML dmaengine: fsl-dpaa2-qdma: add missing MODULE_DESCRIPTION() macro dmaengine: ti: add missing MODULE_DESCRIPTION() macros dmaengine: ti: cppi41: add missing MODULE_DESCRIPTION() macro dmaengine: virt-dma: add missing MODULE_DESCRIPTION() macro dmaengine: ti: k3-udma: Fix BCHAN count with UHC and HC channels dmaengine: sh: rz-dmac: Fix lockdep assert warning dmaengine: qcom: gpi: clean up the IRQ disable/enable in gpi_reset_chan() dmaengine: fsl-edma: change the memory access from local into remote mode in i.MX 8QM dmaengine: qcom: gpi: remove unused struct 'reg_info' dmaengine: moxart-dma: remove unused struct 'moxart_filter_data' dt-bindings: fsl-qdma: Convert to yaml format dmaengine: fsl-edma: remove redundant "idle" field from fsl_chan dmaengine: fsl-edma: request per-channel IRQ only when channel is allocated dmaengine: stm32-dma3: defer channel registration to specify channel name dmaengine: add channel device name to channel registration dmaengine: stm32-dma3: improve residue granularity dmaengine: stm32-dma3: add device_pause and device_resume ops dmaengine: stm32-dma3: add DMA_MEMCPY capability ...
2024-07-24sysctl: treewide: constify the ctl_table argument of proc_handlersJoel Granados7-14/+14
const qualify the struct ctl_table argument in the proc_handler function signatures. This is a prerequisite to moving the static ctl_table structs into .rodata data which will ensure that proc_handler function pointers cannot be modified. This patch has been generated by the following coccinelle script: ``` virtual patch @r1@ identifier ctl, write, buffer, lenp, ppos; identifier func !~ "appldata_(timer|interval)_handler|sched_(rt|rr)_handler|rds_tcp_skbuf_handler|proc_sctp_do_(hmac_alg|rto_min|rto_max|udp_port|alpha_beta|auth|probe_interval)"; @@ int func( - struct ctl_table *ctl + const struct ctl_table *ctl ,int write, void *buffer, size_t *lenp, loff_t *ppos); @r2@ identifier func, ctl, write, buffer, lenp, ppos; @@ int func( - struct ctl_table *ctl + const struct ctl_table *ctl ,int write, void *buffer, size_t *lenp, loff_t *ppos) { ... } @r3@ identifier func; @@ int func( - struct ctl_table * + const struct ctl_table * ,int , void *, size_t *, loff_t *); @r4@ identifier func, ctl; @@ int func( - struct ctl_table *ctl + const struct ctl_table *ctl ,int , void *, size_t *, loff_t *); @r5@ identifier func, write, buffer, lenp, ppos; @@ int func( - struct ctl_table * + const struct ctl_table * ,int write, void *buffer, size_t *lenp, loff_t *ppos); ``` * Code formatting was adjusted in xfs_sysctl.c to comply with code conventions. The xfs_stats_clear_proc_handler, xfs_panic_mask_proc_handler and xfs_deprecated_dointvec_minmax where adjusted. * The ctl_table argument in proc_watchdog_common was const qualified. This is called from a proc_handler itself and is calling back into another proc_handler, making it necessary to change it as part of the proc_handler migration. Co-developed-by: Thomas Weißschuh <[email protected]> Signed-off-by: Thomas Weißschuh <[email protected]> Co-developed-by: Joel Granados <[email protected]> Signed-off-by: Joel Granados <[email protected]>
2024-07-24Merge tag 'random-6.11-rc1-for-linus' of ↵Linus Torvalds1-1/+17
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random Pull random number generator updates from Jason Donenfeld: "This adds getrandom() support to the vDSO. First, it adds a new kind of mapping to mmap(2), MAP_DROPPABLE, which lets the kernel zero out pages anytime under memory pressure, which enables allocating memory that never gets swapped to disk but also doesn't count as being mlocked. Then, the vDSO implementation of getrandom() is introduced in a generic manner and hooked into random.c. Next, this is implemented on x86. (Also, though it's not ready for this pull, somebody has begun an arm64 implementation already) Finally, two vDSO selftests are added. There are also two housekeeping cleanup commits" * tag 'random-6.11-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: MAINTAINERS: add random.h headers to RNG subsection random: note that RNDGETPOOL was removed in 2.6.9-rc2 selftests/vDSO: add tests for vgetrandom x86: vdso: Wire up getrandom() vDSO implementation random: introduce generic vDSO getrandom() implementation mm: add MAP_DROPPABLE for designating always lazily freeable mappings
2024-07-24ublk: fix UBLK_CMD_DEL_DEV_ASYNC handlingMing Lei1-1/+4
In ublk_ctrl_uring_cmd(), ioctl command NR should be used for matching _IOC_NR(cmd_op). Fix it by adding one private macro, and this way is clean. Fixes: 13fe8e6825e4 ("ublk: add UBLK_CMD_DEL_DEV_ASYNC") Signed-off-by: Ming Lei <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jens Axboe <[email protected]>
2024-07-24net: stmmac: Correct byte order of perfect_matchSimon Horman4-5/+5
The perfect_match parameter of the update_vlan_hash operation is __le16, and is correctly converted from host byte-order in the lone caller, stmmac_vlan_update(). However, the implementations of this caller, dwxgmac2_update_vlan_hash() and dwxgmac2_update_vlan_hash(), both treat this parameter as host byte order, using the following pattern: u32 value = ... ... writel(value | perfect_match, ...); This is not correct because both: 1) value is host byte order; and 2) writel expects a host byte order value as it's first argument I believe that this will break on big endian systems. And I expect it has gone unnoticed by only being exercised on little endian systems. The approach taken by this patch is to update the callback, and it's caller to simply use a host byte order value. Flagged by Sparse. Compile tested only. Fixes: c7ab0b8088d7 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available") Signed-off-by: Simon Horman <[email protected]> Reviewed-by: Maxime Chevallier <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2024-07-24thermal: core: Back off when polling thermal zones on errorsRafael J. Wysocki2-7/+61
Commit a8a261774466 ("thermal: core: Call monitor_thermal_zone() if zone temperature is invalid") introduced a polling mechanism by which the thermal core attampts to get a valid temperature value for thermal zones where the .get_temp() callback returns errors to start with (for example, due to initialization ordering woes). However, this polling is carried out periodically ad infinitum and every iteration of it causes a message to be printed to the kernel log which means a lot of log noise on systems where there are thermal zones that never get ready for some reason. It is also not really useful to continuously poll thermal zones that never respond. To address this, modify the thermal core to increase the delay between consecutive thermal zone temperature checks after every check that fails until it reaches a certain maximum value. At that point, the thermal zone in question will be disabled, but user space will be able to reenable it if it believes that the failure is transient. Also change the code to print messages regarding failed temperature checks to the kernel log only twice, once when the thermal zone's .get_temp() callback returns an error for the first time and once when disabling the given thermal zone. In addition, a dev_crit() message will be printed at that point if the given thermal zone contains a critical trip point to notify the system operator about the situation. Fixes: a8a261774466 ("thermal: core: Call monitor_thermal_zone() if zone temperature is invalid") Link: https://lore.kernel.org/linux-acpi/CAGnHSE=RyPK++UG0-wAtVKgeJxe0uzFYgLxm+RUOKKoQquW=Ow@mail.gmail.com/ Reported-by: Tom Yan <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]> Link: https://patch.msgid.link/[email protected]
2024-07-23ice: Fix recipe read procedureWojciech Drewek1-4/+4
When ice driver reads recipes from firmware information about need_pass_l2 and allow_pass_l2 flags is not stored correctly. Those flags are stored as one bit each in ice_sw_recipe structure. Because of that, the result of checking a flag has to be casted to bool. Note that the need_pass_l2 flag currently works correctly, because it's stored in the first bit. Fixes: bccd9bce29e0 ("ice: Add guard rule when creating FDB in switchdev") Reviewed-by: Marcin Szycik <[email protected]> Reviewed-by: Przemek Kitszel <[email protected]> Signed-off-by: Wojciech Drewek <[email protected]> Reviewed-by: Simon Horman <[email protected]> Tested-by: Sujai Buvaneswaran <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2024-07-23ice: Add a per-VF limit on number of FDIR filtersAhmed Zaki4-1/+21
While the iavf driver adds a s/w limit (128) on the number of FDIR filters that the VF can request, a malicious VF driver can request more than that and exhaust the resources for other VFs. Add a similar limit in ice. CC: [email protected] Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF") Reviewed-by: Przemek Kitszel <[email protected]> Suggested-by: Sridhar Samudrala <[email protected]> Signed-off-by: Ahmed Zaki <[email protected]> Reviewed-by: Wojciech Drewek <[email protected]> Tested-by: Rafal Romanowski <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2024-07-23Merge tag 'rpmsg-v6.11' of ↵Linus Torvalds2-3/+4
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux Pull rpmsg updates from Bjorn Andersson: - fix interrupt handling in the stm32 remoteproc driver when being attached to an already running remote processor - fix invalid kernel-doc and add missing MODULE_DESCRIPTION() in the rpmsg char driver * tag 'rpmsg-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: rpmsg: char: add missing MODULE_DESCRIPTION() macro remoteproc: stm32_rproc: Fix mailbox interrupts queuing rpmsg: char: Fix rpmsg_eptdev structure documentation
2024-07-23Merge tag 'rproc-v6.11' of ↵Linus Torvalds14-46/+346
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux Pull remoteproc updates from Bjorn Andersson: - The maximum amount of DDR memory used by the Mediatek MT8188/MT8195 SCP is increased to handle new use cases. Handling of optional L1TCM memory is made actually optional. - An optimization is introduced to only clear the unused portion of IPI shared buffers, rather than the entire buffer before writing the message. - Detection for IPC-only mode in the TI K3 DSP remoteproc driver is corrected. The loglevel of a debug print in the same is lowered from error. - Support for attaching to an running remote processor is added to the Xilinx R5F. - An in-kernel implementation of the Qualcomm "protected domain mapper" (aka service registry) service is introduced, to remove the dependency on a userspace implementation to detect when the battery monitor and USB Type-C port manager becomes available. This is then integrated with the Qualcomm remoteproc driver. - The Qualcomm PAS remoteproc driver gains support for attempting to bust hwspinlocks held by the remote processor when it crashed/stopped. - The TI OMAP remoteproc driver is transitioned to use devres helpers for various forms of allocations. - Parsing of memory-regions in the i.MX remoteproc driver is improved to avoid a NULL pointer dereference if the phandle reference is empty. of_node reference counting is corrected in the same. * tag 'rproc-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: remoteproc: mediatek: Increase MT8188/MT8195 SCP core0 DRAM size remoteproc: k3-dsp: Fix log levels where appropriate remoteproc: xlnx: Add attach detach support remoteproc: qcom: select AUXILIARY_BUS remoteproc: k3-r5: Fix IPC-only mode detection remoteproc: mediatek: Don't attempt to remap l1tcm memory if missing remoteproc: qcom: enable in-kernel PD mapper dt-bindings: remoteproc: imx_rproc: Add minItems for power-domain remoteproc: imx_rproc: Fix refcount mistake in imx_rproc_addr_init remoteproc: omap: Use devm_rproc_add() helper remoteproc: omap: Use devm action to release reserved memory remoteproc: omap: Use devm_rproc_alloc() helper remoteproc: imx_rproc: Skip over memory region when node value is NULL dt-bindings: remoteproc: k3-dsp: Correct optional sram properties for AM62A SoCs remoteproc: qcom_q6v5_pas: Add hwspinlock bust on stop soc: qcom: smem: Add qcom_smem_bust_hwspin_lock_by_host() remoteproc: mediatek: Zero out only remaining bytes of IPI buffer
2024-07-23Merge tag 'hwlock-v6.11' of ↵Linus Torvalds3-0/+56
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux Pull hwspinlock updates from Bjorn Andersson: "This introduces a mechanism in the hardware spinlock framework, and the Qualcomm TCSR mutex driver, for allowing clients to bust locks held by a remote processor in the event that this enters a faulty state while holding the shared lock" * tag 'hwlock-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: hwspinlock: qcom: implement bust operation hwspinlock: Introduce hwspin_lock_bust()
2024-07-23clk: samsung: fix getting Exynos4 fin_pll rate from external clocksKrzysztof Kozlowski1-6/+7
Commit 0dc83ad8bfc9 ("clk: samsung: Don't register clkdev lookup for the fixed rate clocks") claimed registering clkdev lookup is not necessary anymore, but that was not entirely true: Exynos4210/4212/4412 clock code still relied on it to get the clock rate of xxti or xusbxti external clocks. Drop that requirement by accessing already registered clk_hw when looking up the xxti/xusbxti rate. Reported-by: Artur Weber <[email protected]> Closes: https://lore.kernel.org/all/[email protected]/ Fixes: 0dc83ad8bfc9 ("clk: samsung: Don't register clkdev lookup for the fixed rate clocks") Cc: <[email protected]> Signed-off-by: Krzysztof Kozlowski <[email protected]> Link: https://lore.kernel.org/r/[email protected] Tested-by: Artur Weber <[email protected]> # Exynos4212 Signed-off-by: Stephen Boyd <[email protected]>
2024-07-23Merge tag 'i2c-for-6.11-rc1-second-batch' of ↵Linus Torvalds4-15/+24
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull more i2c updates from Wolfram Sang: "The I2C core has two header documentation updates as the dependecies are in now. The I2C host drivers add some patches which nearly fell through the cracks: - Added descriptions in the DTS for the Qualcomm SM8650 and SM8550 Camera Control Interface (CCI). - Added support for the "settle-time-us" property, which allows the gpio-mux device to switch from one bus to another with a configurable delay. The time can be set in the DTS. The latest change also includes file sorting. - Fixed slot numbering in the SMBus framework to prevent failures when more than 8 slots are occupied. It now enforces a a maximum of 8 slots to be used. This ensures that the Intel PIIX4 device can register the SPDs correctly without failure, even if other slots are populated but not used" * tag 'i2c-for-6.11-rc1-second-batch' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: header: improve kdoc for i2c_algorithm i2c: header: remove unneeded stuff regarding i2c_algorithm i2c: piix4: Register SPDs i2c: smbus: remove i801 assumptions from SPD probing i2c: mux: gpio: Add support for the 'settle-time-us' property i2c: mux: gpio: Re-order #include to match alphabetic order dt-bindings: i2c: mux-gpio: Add 'settle-time-us' property dt-bindings: i2c: qcom-cci: Document sm8650 compatible dt-bindings: i2c: qcom-cci: Document sm8550 compatible
2024-07-23Merge tag 'mailbox-v6.11' of ↵Linus Torvalds8-43/+280
git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox Pull mailbox updates from Jassi Brar: "broadcom: - remove unused pdc_dma_map imx: - fix TXDB_V2 channel race condition mediatek: - cleanup and refactor driver - add bindings for gce-props omap: - fix mailbox interrupt sharing qcom: - add bindings for SA8775p - add CPUCP driver zynqmp: - make polling period configurable" * tag 'mailbox-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox: mailbox: mtk-cmdq: Move devm_mbox_controller_register() after devm_pm_runtime_enable() mailbox: zynqmp-ipi: Make polling period configurable mailbox: qcom-cpucp: fix 64BIT dependency mailbox: Add support for QTI CPUCP mailbox controller dt-bindings: mailbox: qcom: Add CPUCP mailbox controller bindings dt-bindings: remoteproc: qcom,sa8775p-pas: Document the SA8775p ADSP, CDSP and GPDSP mailbox: mtk-cmdq: add missing MODULE_DESCRIPTION() macro mailbox: bcm-pdc: remove unused struct 'pdc_dma_map' mailbox: imx: fix TXDB_V2 channel race condition mailbox: omap: Fix mailbox interrupt sharing mailbox: mtk-cmdq: Dynamically allocate clk_bulk_data structure mailbox: mtk-cmdq: Move and partially refactor clocks probe mailbox: mtk-cmdq: Stop requiring name for GCE clock dt-bindings: mailbox: Add mediatek,gce-props.yaml
Powered by cgit, Gruvboxed by Blaster4385.