| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit d49216438139
("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
removed Kconfig SPI_MASTER or I2C dependency for SERIAL_SC16IS7XX (core).
This removal was done because I inadvertently misinterpreted some review
comments.
Because of that, the driver question now pops up if both I2C and
SPI_MASTER are disabled.
Re-add Kconfig SPI_MASTER or I2C dependency to fix the problem.
Suggested-by: Geert Uytterhoeven <[email protected]>
Fixes: d49216438139 ("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
Signed-off-by: Hugo Villeneuve <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Commit d49216438139
("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
renamed SERIAL_SC16IS7XX_CORE by SERIAL_SC16IS7XX. This means that some
configs should have been updated when I submitted the original patch, but
unfortunately they were not. Geert mentioned for example:
arch/mips/configs/cu1??0-neo_defconfig
Rename SERIAL_SC16IS7XX to SERIAL_SC16IS7XX_CORE so that existing configs
will still work correctly.
Suggested-by: Geert Uytterhoeven <[email protected]>
Fixes: d49216438139 ("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
Signed-off-by: Hugo Villeneuve <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Split the common code from sc16is7xx driver and move the I2C and SPI bus
parts into interface-specific source files.
sc16is7xx becomes the core functions which can support multiple bus
interfaces like I2C and SPI.
No functional changes intended.
Also simplify and improve Kconfig entries.
- Capitalize SPI keyword for consistency
- Display list of supported ICs each on a separate line (and aligned) to
facilitate locating a specific IC model
- Add Manufacturer name at start of description string
- Add UART keyword to description string
Suggested-by: Andy Shevchenko <[email protected]>
Signed-off-by: Hugo Villeneuve <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The driver actually supports more than one chip.
Update Kconfig entry to list the supported chips.
Signed-off-by: Andy Shevchenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- Support for tuning for systems with fast misaligned accesses.
- Support for SBI-based suspend.
- Support for the new SBI debug console extension.
- The T-Head CMOs now use PA-based flushes.
- Support for enabling the V extension in kernel code.
- Optimized IP checksum routines.
- Various ftrace improvements.
- Support for archrandom, which depends on the Zkr extension.
- The build is no longer broken under NET=n, KUNIT=y for ports that
don't define their own ipv6 checksum.
* tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (56 commits)
lib: checksum: Fix build with CONFIG_NET=n
riscv: lib: Check if output in asm goto supported
riscv: Fix build error on rv32 + XIP
riscv: optimize ELF relocation function in riscv
RISC-V: Implement archrandom when Zkr is available
riscv: Optimize hweight API with Zbb extension
riscv: add dependency among Image(.gz), loader(.bin), and vmlinuz.efi
samples: ftrace: Add RISC-V support for SAMPLE_FTRACE_DIRECT[_MULTI]
riscv: ftrace: Add DYNAMIC_FTRACE_WITH_DIRECT_CALLS support
riscv: ftrace: Make function graph use ftrace directly
riscv: select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
lib/Kconfig.debug: Update AS_HAS_NON_CONST_LEB128 comment and name
riscv: Restrict DWARF5 when building with LLVM to known working versions
riscv: Hoist linker relaxation disabling logic into Kconfig
kunit: Add tests for csum_ipv6_magic and ip_fast_csum
riscv: Add checksum library
riscv: Add checksum header
riscv: Add static key for misaligned accesses
asm-generic: Improve csum_fold
RISC-V: selftests: cbo: Ensure asm operands match constraints
...
|
|
We extend the existing RISC-V SBI earlycon support to use the new
RISC-V SBI debug console extension.
Signed-off-by: Anup Patel <[email protected]>
Reviewed-by: Andrew Jones <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Palmer Dabbelt <[email protected]>
|
|
Device number 204 has a range of minors on major number.
uart_register_driver is failing due to lack of minor numbers
when more number of uart ports used. So, to avoid minor number
limitation on 204 major number use dynamic major allocation
when more than 4 uart ports used otherwise use static major
allocation.
https://docs.kernel.org/arch/arm/sa1100/serial_uart.html
Signed-off-by: Manikanta Guntupalli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add driver for the ACM gadget controller of the Espressif ESP32S3 SoC.
Hardware specification is available at the following URL:
https://www.espressif.com/sites/default/files/documentation/esp32-s3_technical_reference_manual_en.pdf
(Chapter 33 USB Serial/JTAG Controller)
Signed-off-by: Max Filippov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add driver for the UART controllers of the Espressif ESP32 and ESP32S3
SoCs. Hardware specification is available at the following URLs:
https://www.espressif.com/sites/default/files/documentation/esp32_technical_reference_manual_en.pdf
(Chapter 13 UART Controller)
https://www.espressif.com/sites/default/files/documentation/esp32-s3_technical_reference_manual_en.pdf
(Chapter 26 UART Controller)
Signed-off-by: Max Filippov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver updates for 6.5-rc1.
Included in here are:
- tty_audit code cleanups from Jiri
- more 8250 cleanups from Ilpo
- samsung_tty driver bugfixes
- 8250 lock port updates
- usual fsl_lpuart driver updates and fixes
- other small serial driver fixes and updates, full details in the
shortlog
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
tty_audit: make data of tty_audit_log() const
tty_audit: make tty pointers in exposed functions const
tty_audit: make icanon a bool
tty_audit: invert the condition in tty_audit_log()
tty_audit: use kzalloc() in tty_audit_buf_alloc()
tty_audit: use TASK_COMM_LEN for task comm
Revert "8250: add support for ASIX devices with a FIFO bug"
serial: atmel: don't enable IRQs prematurely
tty: serial: Add Nuvoton ma35d1 serial driver support
tty: serial: fsl_lpuart: add earlycon for imx8ulp platform
tty: serial: imx: fix rs485 rx after tx
selftests: tty: add selftest for tty timestamp updates
tty: tty_io: update timestamps on all device nodes
tty: fix hang on tty device with no_room set
serial: core: fix -EPROBE_DEFER handling in init
serial: 8250_omap: Use force_suspend and resume for system suspend
tty: serial: samsung_tty: Use abs() to simplify some code
tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() when iterating clk
tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() in case of error
serial: 8250: Apply FSL workarounds also without SERIAL_8250_CONSOLE
...
|
|
Pull arm documentation move from Jonathan Corbet:
"Move the Arm architecture documentation under Documentation/arch/.
This brings some order to the documentation directory, declutters the
top-level directory, and makes the documentation organization more
closely match that of the source"
* tag 'docs-arm-move' of git://git.lwn.net/linux:
dt-bindings: Update Documentation/arm references
docs: update some straggling Documentation/arm references
crypto: update some Arm documentation references
mips: update a reference to a moved Arm Document
arm64: Update Documentation/arm references
arm: update in-source documentation references
arm: docs: Move Arm documentation to Documentation/arch/
|
|
This adds UART and console driver for Nuvoton ma35d1 Soc.
It supports full-duplex communication, FIFO control, and
hardware flow control.
Command line set "console=ttyNVT0,115200", NVT means
Nuvoton MA35 UART port. The UART driver probe will
create path named "/dev/ttyNVTx".
Signed-off-by: Jacky Huang <[email protected]>
Reviewed-by: Ilpo Järvinen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The Arm documentation has moved to Documentation/arch/arm; update the
last remaining references to match.
Cc: Dmitry Torokhov <[email protected]>
Cc: Chen-Yu Tsai <[email protected]>
Cc: Samuel Holland <[email protected]>
Cc: Thierry Reding <[email protected]>
Acked-by: Nicolas Ferre <[email protected]>
Acked-by: Jernej Skrabec <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Acked-by: Uwe Kleine-König <[email protected]> # for pwm
Signed-off-by: Jonathan Corbet <[email protected]>
|
|
In a COMPILE_TEST configuration, the cpm_uart driver uses symbols from
the cpm_uart_cpm2.c file. This file is compiled only when CONFIG_CPM2 is
set.
Without this dependency, the linker fails with some missing symbols for
COMPILE_TEST configuration that needs SERIAL_CPM without enabling CPM2.
This lead to:
depends on CPM2 || CPM1 || (PPC32 && CPM2 && COMPILE_TEST)
This dependency does not make sense anymore and can be simplified
removing all the COMPILE_TEST part.
Signed-off-by: Herve Codina <[email protected]>
Reported-by: kernel test robot <[email protected]>
Link: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Fixes: e3e7b13bffae ("serial: allow COMPILE_TEST for some drivers")
Cc: stable <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the SiFive serial
driver Kconfig entries from the SOC_ symbols to ARCH_ instead.
Signed-off-by: Conor Dooley <[email protected]>
Link: https://lore.kernel.org/r/20230406-carnival-aspirate-fcf69a30078c@spud
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Commit 1ea35b355722 ("ARM: s3c: remove s3c24xx specific hacks"), allows
simplifying the whole config logic for SERIAL_SAMSUNG_UARTS, and did this
config simplification. However, it misses that SERIAL_SAMSUNG_UARTS_4's
effect was just to control SERIAL_SAMSUNG_UARTS, and with the commit's
change, the config SERIAL_SAMSUNG_UARTS_4 has no remaining effect and can
be deleted.
Remove this obsolete config SERIAL_SAMSUNG_UARTS_4.
Signed-off-by: Lukas Bulwahn <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
dependency"
This reverts commit 5779a072c248db7a40cfd0f5ea958097fd1d9a30.
This results in a link error of
ld: drivers/tty/serial/earlycon.o: in function `parse_options':
drivers/tty/serial/earlycon.c:99: undefined reference to `uart_parse_earlycon'
When the config is in this state
CONFIG_SERIAL_CORE=m
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_FSL_LPUART=m
CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
Fixes: 5779a072c248 ("tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency")
Cc: stable <[email protected]>
Signed-off-by: Tom Rix <[email protected]>
Reviewed-by: Randy Dunlap <[email protected]>
Acked-by: Jiri Slaby <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
|
|
Since commit 0166dc11be91 ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <[email protected]>
Cc: Karol Gugala <[email protected]>
Cc: Mateusz Holenko <[email protected]>
Cc: Gabriel Somlo <[email protected]>
Cc: Joel Stanley <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Acked-by: Gabriel Somlo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Now that earlycon semihost driver works on RISC-V too, let's use a
much more generic name for the driver.
Signed-off-by: Bin Meng <[email protected]>
Tested-by: Sergey Matyukevich <[email protected]>
Acked-by: Palmer Dabbelt <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Per RISC-V semihosting spec [1], implement semihost.h for the existing
Arm semihosting earlycon driver to work on RISC-V.
Link: https://github.com/riscv/riscv-semihosting-spec/blob/main/riscv-semihosting-spec.adoc [1]
Signed-off-by: Bin Meng <[email protected]>
Tested-by: Sergey Matyukevich <[email protected]>
Acked-by: Palmer Dabbelt <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <[email protected]>
Acked-by: Linus Walleij <[email protected]>
Acked-by: Jonathan Cameron <[email protected]>
Acked-by: Daniel Lezcano <[email protected]>
Acked-by: Miquel Raynal <[email protected]>
Acked-by: Ulf Hansson <[email protected]>
Acked-by: Stephen Boyd <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
With the aim of dropping direct selects of drivers from Kconfig.socs,
default the SiFive serial drivers to enabled if SOC_CANAAN.
Signed-off-by: Conor Dooley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
With the aim of dropping direct selects of drivers from Kconfig.socs,
default the SiFive serial drivers to the value of SOC_SIFIVE.
Signed-off-by: Conor Dooley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Fixes:
- When we added basic vDSO support in kernel 5.18 we introduced a bug
which prevented a mmap() of graphic card memory. This is because we
used the DMB (data memory break trap bit) page flag as special-bit,
but missed to clear that bit when loading the TLB.
- Graphics card memory size was not correctly aligned
- Spelling fixes (from Colin Ian King)
Enhancements:
- PDC console (which uses firmware calls) now rewritten as early
console
- Reduced size of alternative tables"
* tag 'parisc-for-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix spelling mistake "mis-match" -> "mismatch" in eisa driver
parisc: Fix userspace graphics card breakage due to pgtable special bit
parisc: fbdev/stifb: Align graphics memory size to 4MB
parisc: Convert PDC console to an early console
parisc: Reduce kernel size by packing alternative tables
|
|
Rewrite the PDC console to become an early console.
Beside the fact that now boot information is visible until another
(text- or graphics) console takes over, this benefits as well machines
with a yet-unsupported STI console and kgdb.
Signed-off-by: Helge Deller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of TTY and Serial driver updates for 6.1-rc1.
Lots of cleanups in here, no real new functionality this time around,
with the diffstat being that we removed more lines than we added!
Included in here are:
- termios unification cleanups from Al Viro, it's nice to finally get
this work done
- tty serial transmit cleanups in various drivers in preparation for
more cleanup and unification in future releases (that work was not
ready for this release)
- n_gsm fixes and updates
- ktermios cleanups and code reductions
- dt bindings json conversions and updates for new devices
- some serial driver updates for new devices
- lots of other tiny cleanups and janitorial stuff. Full details in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (102 commits)
serial: cpm_uart: Don't request IRQ too early for console port
tty: serial: do unlock on a common path in altera_jtaguart_console_putc()
tty: serial: unify TX space reads under altera_jtaguart_tx_space()
tty: serial: use FIELD_GET() in lqasc_tx_ready()
tty: serial: extend lqasc_tx_ready() to lqasc_console_putchar()
tty: serial: allow pxa.c to be COMPILE_TESTed
serial: stm32: Fix unused-variable warning
tty: serial: atmel: Add COMMON_CLK dependency to SERIAL_ATMEL
serial: 8250: Fix restoring termios speed after suspend
serial: Deassert Transmit Enable on probe in driver-specific way
serial: 8250_dma: Convert to use uart_xmit_advance()
serial: 8250_omap: Convert to use uart_xmit_advance()
MAINTAINERS: Solve warning regarding inexistent atmel-usart binding
serial: stm32: Deassert Transmit Enable on ->rs485_config()
serial: ar933x: Deassert Transmit Enable on ->rs485_config()
tty: serial: atmel: Use FIELD_PREP/FIELD_GET
tty: serial: atmel: Make the driver aware of the existence of GCLK
tty: serial: atmel: Only divide Clock Divisor if the IP is USART
tty: serial: atmel: Separate mode clearing between UART and USART
dt-bindings: serial: atmel,at91-usart: Add gclk as a possible USART clock
...
|
|
There is no issue compiling pxa.c even in the SERIAL_8250=y case. So to
cover it in the usual configurations, add "|| COMPILE_TEST" there.
Signed-off-by: Jiri Slaby <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Now that the driver makes use of `__clk_is_enabled()` in order to
know whether a `clk_disable_unprepare()` is needed or not on the
GCLK, a new dependency has been introduced: COMMON_CLK. If this
`CONFIG_COMMON_CLK` is not enabled, whatever config may have this
driver enabled without COMMON_CLK then an undefined reference to
`__clk_is_enabled()` will be issued by the linker.
Thus, make sure that, unless `CONFIG_COMMON_CLK` is enabled, this
driver is not compiled.
Fixes: 5e3ce1f26129 ("tty: serial: atmel: Make the driver aware of the existence of GCLK")
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Sergiu Moga <[email protected]>
Acked-by: Nicolas Ferre <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Remove the limitation of SERIAL_FSL_LPUART=y,
as we may need enable this console while SERIAL_FSL_LPUART=m.
Signed-off-by: Jindong Yue <[email protected]>
Signed-off-by: Sherry Sun <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
With Broadcom Broadband arch ARCH_BCMBCA supported in the kernel, this
patch series migrate the ARCH_BCM4908 symbol to ARCH_BCMBCA. Hence
replace ARCH_BCM4908 with ARCH_BCMBCA in subsystem Kconfig files.
Signed-off-by: William Zhang <[email protected]>
Acked-by: Guenter Roeck <[email protected]> (for watchdog)
Acked-by: Bjorn Helgaas <[email protected]> (for drivers/pci)
Acked-by: Wolfram Sang <[email protected]> (for i2c)
Acked-by: Philipp Zabel <[email protected]> (for reset)
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Florian Fainelli <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make
the tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo).
Also included in here is the obligatory n_gsm updates from Daniel
Starke and lots of tiny driver updates and minor fixes and tweaks for
other smaller serial drivers.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements
tty: amiserial: Fix comment typo
tty: serial: document uart_get_console()
tty: serial: serial_core, reformat kernel-doc for functions
Documentation: serial: link uart_ops properly
Documentation: serial: move GPIO kernel-doc to the functions
Documentation: serial: dedup kernel-doc for uart functions
Documentation: serial: move uart_ops documentation to the struct
dt-bindings: serial: snps-dw-apb-uart: Document Rockchip RV1126
serial: mvebu-uart: uart2 error bits clearing
tty: serial: fsl_lpuart: correct the count of break characters
serial: stm32: make info structs static to avoid sparse warnings
serial: fsl_lpuart: zero out parity bit in CS7 mode
tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.
serial: 8250_bcm2835aux: Add missing clk_disable_unprepare()
tty: vt: initialize unicode screen buffer
serial: remove VR41XX serial driver
serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
serial: 8250_dwlib: remove redundant sanity check for RS485 flags
dt_bindings: rs485: Correct delay values
...
|
|
Commit d3164e2f3b0a ("MIPS: Remove VR41xx support") removed support
for MIPS VR41xx platform, so remove exclusive drivers for this
platform, too.
Signed-off-by: Thomas Bogendoerfer <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Prepare for the BCM63138 ARCH_BCM_63XX migration to ARCH_BCMBCA. Make
SERIAL_BCM63XX depending on ARCH_BCMBCA.
Signed-off-by: William Zhang <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>
|
|
I2C implementation on this chip has a few key differences
compared to SPI, as described in previous patches.
* extended register space access needs no extra logic
* slave address is used to select which UART to communicate
with
To accommodate these differences, add an I2C interface config,
set the RevID register address and implement an empty method
for setting the GlobalCommand register, since no special handling
is needed for the extended register space.
To handle the port-specific slave address, create an I2C dummy
device for each port, except the base one (UART0), which is
expected to be the one specified in firmware, and create a
regmap for each I2C device.
Add minimum and maximum slave addresses to each devtype for
sanity checking.
Also, use a separate regmap config with no write_flag_mask,
since I2C has a R/W bit in its slave address, and set the
max register to the address of the RevID register, since the
extended register space needs no extra logic.
Finally, add the I2C driver.
Reviewed-by: Andy Shevchenko <[email protected]>
Signed-off-by: Cosmin Tanislav <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.19-rc1.
Lots of tiny cleanups in here, the major stuff is:
- termbit cleanups and unification by Ilpo. A much needed change that
goes a long way to making things simpler for all of the different
arches
- tty documentation cleanups and movements to their own place in the
documentation tree
- old tty driver cleanups and fixes from Jiri to bring some existing
drivers into the modern world
- RS485 cleanups and unifications to make it easier for individual
drivers to support this mode instead of having to duplicate logic
in each driver
- Lots of 8250 driver updates and additions
- new device id additions
- n_gsm continued fixes and cleanups
- other minor serial driver updates and cleanups
All of these have been in linux-next for weeks with no reported issues"
* tag 'tty-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (166 commits)
tty: Rework receive flow control char logic
pcmcia: synclink_cs: Don't allow CS5-6
serial: stm32-usart: Correct CSIZE, bits, and parity
serial: st-asc: Sanitize CSIZE and correct PARENB for CS7
serial: sifive: Sanitize CSIZE and c_iflag
serial: sh-sci: Don't allow CS5-6
serial: txx9: Don't allow CS5-6
serial: rda-uart: Don't allow CS5-6
serial: digicolor-usart: Don't allow CS5-6
serial: uartlite: Fix BRKINT clearing
serial: cpm_uart: Fix build error without CONFIG_SERIAL_CPM_CONSOLE
serial: core: Do stop_rx in suspend path for console if console_suspend is disabled
tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate.
dt-bindings: serial: renesas,em-uart: Add RZ/V2M clock to access the registers
serial: 8250_fintek: Check SER_RS485_RTS_* only with RS485
Revert "serial: 8250_mtk: Make sure to select the right FEATURE_SEL"
serial: msm_serial: disable interrupts in __msm_console_write()
serial: meson: acquire port->lock in startup()
serial: 8250_dw: Use dev_err_probe()
serial: 8250_dw: Use devm_add_action_or_reset()
...
|
|
Add early console support in stm32 uart driver.
Signed-off-by: Alexandre Torgue <[email protected]>
Signed-off-by: Valentin Caron <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Some more serial drivers can be compile-tested under certain
circumstances (when building a specific architecture). So allow for
that.
This reduces the need of zillion mach/subarch-specific configs. And
since the 0day bot has only allmodconfig's for some archs, this
increases build coverage there too.
Note that cpm needs a minor update in the header, so that it drags in
at least some defines (CPM2 ones).
Signed-off-by: Jiri Slaby <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
pic32_uart contains this:
#ifdef CONFIG_SERIAL_PIC32_CONSOLE
...
console_initcall(pic32_console_init);
...
core_initcall(pic32_late_console_init);
...
#endif
...
arch_initcall(pic32_uart_init);
When the driver is built as module, all three above become
module_init(). So if SERIAL_PIC32_CONSOLE is set while SERIAL_PIC32=m,
it results in the following build error:
In file included from include/linux/device/driver.h:21,
from include/linux/device.h:32,
from include/linux/platform_device.h:13,
from drivers/tty/serial/pic32_uart.c:12:
include/linux/module.h:131:49: error: redefinition of '__inittest'
So make sure SERIAL_PIC32_CONSOLE can be set only when SERIAL_PIC32=y --
similar as for other drivers.
Signed-off-by: Jiri Slaby <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
asm-generic
* 'remove-h8300' of git://git.infradead.org/users/hch/misc:
remove the h8300 architecture
This is clearly the least actively maintained architecture we have at
the moment, and probably the least useful. It is now the only one that
does not support MMUs at all, and most of the boards only support 4MB
of RAM, out of which the defconfig kernel needs more than half just
for .text/.data.
Guenter Roeck did the original patch to remove the architecture in 2013
after it had already been obsolete for a while, and Yoshinori Sato brought
it back in a much more modern form in 2015. Looking at the git history
since the reinstantiation, it's clear that almost all commits in the tree
are build fixes or cross-architecture cleanups:
$ git log --no-merges --format=%an v4.5.. arch/h8300/ | sort | uniq
-c | sort -rn | head -n 12
25 Masahiro Yamada
18 Christoph Hellwig
14 Mike Rapoport
9 Arnd Bergmann
8 Mark Rutland
7 Peter Zijlstra
6 Kees Cook
6 Ingo Molnar
6 Al Viro
5 Randy Dunlap
4 Yury Norov
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Add support for the UART block on the ARTPEC-8 SoC. This is closely
related to the variants used on the Exynos chips. The register layout
is identical to Exynos850 et al but the fifo size is different (64 bytes
in each direction for all instances).
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Vincent Whitchurch <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Patches lowering SERIAL_BCM63XX dependencies led to a discussion and
documentation change regarding "depends" usage. Adjust Kconfig entry to
match current guidelines. Make this symbol available for relevant
architectures only.
Cc: Geert Uytterhoeven <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Signed-off-by: Rafał Miłecki <[email protected]>
Ref: f35a07f92616 ("tty: serial: bcm63xx: lower driver dependencies")
Ref: 18084e435ff6 ("Documentation/kbuild: Document platform dependency practises")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Sunplus serial ports are only present on Sunplus SoCs. Hence add a
dependency on ARCH_SUNPLUS, to prevent asking the user about this driver
when configuring a kernel without Sunplus SoC support.
Fixes: 9e8d5470325f25be ("serial: sunplus-uart: Add Sunplus SoC UART Driver")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/59f46272ab5b16853acac4d585c3333cfd394223.1647352195.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This reverts the following commits:
31979060cc07 tty: serial: meson: Fix the compile link error reported by kernel test robot
5427c352a993 tty: serial: meson: Added S4 SOC compatibility
19b2ba0baffc tty: serial: meson: The system stuck when you run the stty command on the console to change the baud rate
e5fc2b99840d tty: serial: meson: Make some bit of the REG5 register writable
44023b8e1f14 tty: serial: meson: Describes the calculation of the UART baud rate clock using a clock frame
6436dd8f9b25 tty: serial: meson: Use devm_ioremap_resource to get register mapped memory
841f913e770f tty: serial: meson: Move request the register region to probe
They seem to cause lots of problems with existing hardware platforms,
and caused build issues, so revert the whole series all at once.
Link: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/all/[email protected]/
Reported-by: Marek Szyprowski <[email protected]>
Reported-by: Jerome Brunet <[email protected]>
Cc: Neil Armstrong <[email protected]>
Cc: Yu Tu <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Describes the calculation of the UART baud rate clock using a clock
frame. Forgot to add in Kconfig kernel test Robot compilation error
due to COMMON_CLK dependency.
Fixes: 44023b8e1f14 ("tty: serial: meson: Describes the calculation of the UART baud rate clock using a clock frame")
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Yu Tu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Add Sunplus SoC UART Driver.
SP7021 UART block contains 5 UARTs.
There are UART0~4 that supported in SP7021, the features list as below.
Support Full-duplex communication.
Support data packet length configurable.
Support stop bit number configurable.
Support force break condition.
Support baud rate configurable.
Support error detection and report.
Support RXD Noise Rejection Vote configurable.
UART0 pinout only support TX/RX two pins.
UART1 to UART4 pinout support TX/RX/CTS/RTS four pins.
Normally UART0 used for kernel console, also can be used for normal uart.
Command line set "console=ttySUP0,115200", SUP means Sunplus Uart Port.
UART driver probe will create path named "/dev/ttySUPx".
https://sunplus.atlassian.net/wiki/spaces/doc/pages/1873412290/13.+Universal+Asynchronous+Receiver+Transmitter+UART
Signed-off-by: Hammer Hsieh <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Implement a new device driver for controlling UART clocks on Marvell
Armada 3700 SoC. This device driver is loaded for devices which match
the compatible string "marvell,armada-3700-uart-clock".
There are more pitfalls related to UART clocks:
- both UARTs use same parent clock source (which can be xtal or one of
the TBG clocks),
- if a TBG clock is used as the parent clock, there are two additional
divisors that can both be configured to divide the rate by 1, 2, ... 6,
but these divisors are again shared between the two UART controllers
on the SOC,
- the configuration of the parent clock source and divisors is done in
the address space of the first UART controller, UART1. Clocks can be
gated separately for UART1 and UART2, but this setting also lives in
the address space of UART1,
- Marvell's Functional Specification for Armada 3720 document has the
clock gating bits swapped, so the one described to gate UART1 clock
actually gates UART2 and vice versa,
- each UART has it's own "special divisor", and this uses the parent
clock described above. These divisors are configure in each UART's
address space separately.
Thus the driver for UART2 controller needs to have access to UART1
address space, since UART1 address space contains some bits exclusive
for UART2 and also some bits which are shared between UART1 and UART2.
Also, during boot, when early console is active on one of the UARTs,
and we want to switch parent clock from xtal (default) to TBG (to be
more flexible with baudrates), the driver changing UART clocks also
needs to be able to change the "special divisor", so that the baudrate
of earlycon is not changed when swtiching to normal console. Thus the
clock driver also needs to be able to access UART2 register space,
for UART2's "special divisor".
For these reasons, this new UART clock driver does not use
ioremap_resource(), but only ioremap() to prevent resource conflicts
between UART clock driver and UART driver.
We need to share only two 32-bit registers between the UART driver and
the UART clock driver:
- UART Clock Control
- UART 2 Baud Rate Divisor
Access to these two registers are protected by one spinlock to prevent
any conflicts. Access is required only during probing, when changing
baudrate or during suspend/resume.
Hardware can be configured to use one of following clocks as UART parent
clock: TBG-A-P, TBG-B-P, TBG-A-S, TBG-B-S, xtal. Not every clock is
usable for higher buadrates. Any subset can be specified in the
device-tree and the driver will choose the best one which also still
supports the mandatory baudrate of 9600 Bd. For smooth boot log output
it is needed to specify clock used by early console, otherwise garbage
would be printed on UART during probe of UART clock driver and
transitioning from early console to normal console.
We are implementing this to be able to configure TBG clock as UART
parent clock, which is required to be able to achieve higher baudrates
than 230400 Bd. We achieve this by referencing this new UART clock
device node in UART's device node. UART clock device driver
automatically chooses the best clock source for UART driver.
Until now, UART's device-tree node needed to reference one of the static
clocks (xtal or one of the TBGs) as parent clock in the `clocks`
phandle - the parent clock which was configured before booting the
kernel. If bootloader changed UART's parent clock, it needed to change
the `clocks` phandle in DTB correspondingly before booting.
From now on both the old mechanism (xtal or TBG referenced as parent
clock in `clocks` phandle) and the new one (UART clock referenced in the
`clocks` phandle) are supported, to provide full backward compatibility
with existing DTS files, full backward compatibility with existing boot
loaders, and to provide new features (runtime clock configuration to
allow higher baudrates than 230400 Bd). New features are available only
with new DTS files.
There was also a discussion about how the UART node and the
clock-controller node could be wrapped together in a new binding [1, 2].
As explained there, this is not possible if we want to keep backwards
compatibility with existing bootloaders, and thus we are doing this by
putting the UART clock-controller node inside the UART1 node.
[1] https://lore.kernel.org/linux-serial/20220120000651.in7s6nazif5qjkme@pali/
[2] https://lore.kernel.org/linux-serial/[email protected]/
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stephen Boyd <[email protected]>
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
Add early console support which relies on the bootloader for the
initialization of the UART.
Please note, that the compatibles are taken from at91-usart MFD
driver.
Tested-by: Claudiu Beznea <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
Acked-by: Richard Genoud <[email protected]>
Signed-off-by: Michael Walle <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Enable serial driver to be built as a module. To do so, init the console
support on driver/module load instead of using console_initcall().
Inspired by commit 87a0b9f98ac5 ("tty: serial: meson: enable console as
module").
Signed-off-by: Sam Protsenko <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|