aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath12k
AgeCommit message (Collapse)AuthorFilesLines
2024-05-02wifi: ath12k: fix the problem that down grade phy mode operationLingbo Kong1-3/+13
Currently, when using WCN7850 or QCN9274 as AP, ath12k always performs down grade phy mode operation regardless of whether the firmware supports EHT capability or not and then vdev will start in HE mode. When stations that support EHT capability try to connect to the AP, the AP will set phy mode to EHT after receiving the association request packet, and then send WMI_PEER_ASSOC_CMDID command to firmware, AP’s firmware will crash. This is because when the ath12k_mac_copy_sband_iftype_data() function handles EHT capability, it does not copy the EHT capability into the iftype[band][type] array according to the interface type. So, interface type should not be used as an index to get eht_cap in ath12k_mac_check_down_grade_phy_mode() function. To address this issue, use types_mask to select the eht_cap in ath12k_mac_check_down_grade_phy_mode() function. This patch affects QCN9274 and WCN7850 because they have the same issue. Hostapd log: wlo1: STA 02:03:7f:37:12:34 IEEE 802.11: Could not set STA to kernel driver Kernel log: [270894.816076] ath12k_pci 0000:03:00.0: failed to send WMI_PEER_SET_PARAM cmd [270894.816111] ath12k_pci 0000:03:00.0: failed to setup peer SMPS for vdev 0: -108 [270894.816122] ath12k_pci 0000:03:00.0: Failed to associate station: 02:03:7f:37:12:34 [270894.843389] ieee80211 phy5: Hardware restart was requested [270894.843517] ath12k_pci 0000:03:00.0: failed to lookup peer 02:03:7f:37:12:34 on vdev 0 [270894.843616] ath12k_pci 0000:03:00.0: failed to send WMI_PEER_DELETE cmd [270894.843650] ath12k_pci 0000:03:00.0: failed to delete peer vdev_id 0 addr 02:03:7f:37:12:34 ret -108 [270894.843663] ath12k_pci 0000:03:00.0: Failed to delete peer: 02:03:7f:37:12:34 for VDEV: 0 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240425083837.5340-1-quic_lingbok@quicinc.com
2024-04-30wifi: ath12k: fix flush failure in recovery scenariosBaochen Qiang1-0/+7
Commit eaf9f17b861b ("wifi: ath12k: relocate ath12k_dp_pdev_pre_alloc() call") moves ath12k_dp_pdev_pre_alloc() from ath12k_core_start() to ath12k_mac_allocate(), resulting in ath12k_mac_flush() failure in recovery scenarios: [ 6849.684104] ath12k_pci 0000:04:00.0: pdev 0 successfully recovered [ 6854.907320] ath12k_pci 0000:04:00.0: failed to flush transmit queue 0 [ 6860.027353] ath12k_pci 0000:04:00.0: failed to flush transmit queue 0 [ 6865.143385] ath12k_pci 0000:04:00.0: failed to flush transmit queue 0 This is because, with ath12k_dp_pdev_pre_alloc() moved to ath12k_mac_allocate(), dp->num_tx_pending is not reset due to ATH12K_FLAG_REGISTERED set in recovery scenarios. So a possible fix would be to reset that counter at some proper point, just like the old design. But considering that the counter tracks number of packets pending to be freed or returned to mac80211, forcefully reset it might make it hard to expose some real issues. For example if somehow ath12k fails to free/return some TX packets, we don't know that because no warnings any more. That is to say we should not reset that counter during recovery (which is already done due to above commit), instead should decrease it each time a packet is freed/returned. Currently almost each related function has this logic implemented, except ath12k_dp_cc_cleanup(). So add the same there to fix this issue. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240426015434.94840-1-quic_bqiang@quicinc.com
2024-04-30wifi: ath12k: check M3 buffer size as well whey trying to reuse itBaochen Qiang1-15/+21
Currently in recovery/resume cases, we do not free M3 buffer but instead will reuse it. This is done by checking m3_mem->vaddr: if it is not NULL we believe M3 buffer is ready and go ahead to reuse it. Note that m3_mem->size is not checked. This is safe for now because currently M3 reuse logic only gets executed in recovery/resume cases and the size keeps unchanged in either of them. However ideally the size should be checked as well, to make the code safer. So add the check there. Now if that check fails, free old M3 buffer and reallocate a new one. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 Fixes: 303c017821d8 ("wifi: ath12k: fix kernel crash during resume") Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240425021740.29221-1-quic_bqiang@quicinc.com
2024-04-24wifi: ath12k: set mlo_capable_flags based on QMI PHY capabilityRaj Kumar Bhagat2-4/+13
Currently, mlo_capable_flags is set to zero if dualmac device is detected based on One Time Programmable (OTP) register value. This is not generic and in future dualmac devices may support Single Link Operation (SLO) and Multi Link Operation (MLO). Thus, set mlo_capable_flags based on 'single_chip_mlo_support' parameter from QMI PHY capability response message from the firmware. Also, add check on mlo_capable_flags to disable MLO parameter in the host capability QMI request message. If the firmware does not respond with this optional parameter 'single_chip_mlo_support' in QMI PHY capability response, default ab->mlo_capable_flags is used. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240418125609.3867730-3-quic_rajkbhag@quicinc.com
2024-04-24wifi: ath12k: read single_chip_mlo_support parameter from QMI PHY capabilityRaj Kumar Bhagat2-2/+24
New parameter 'single_chip_mlo_support' was added in QMI PHY capability response message. This is an optional parameter added in QCN9274 firmware. This parameter states if the firmware supports Single-Link Operation (SLO) and Multi-Link Operation (MLO) within the same device. If single_chip_mlo_support = 1, then intra device SLO/MLO is supported in the firmware. If single_chip_mlo_support = 0, then intra device SLO/MLO is not supported in the firmware. Hence, add support to read 'single_chip_mlo_support' parameter from the QMI PHY capability response message. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240418125609.3867730-2-quic_rajkbhag@quicinc.com
2024-04-24wifi: ath12k: add support to handle beacon miss for WCN7850Kang Yang5-18/+99
When AP goes down or too far away without indication to STA, beacon miss will be detected. Then for WCN7850's firmware, it will use roam event to send beacon miss to host. If STA doesn't handle the beacon miss, will keep the fake connection and unable to roam. So add support for WCN7850 to trigger disconnection from AP when receiving this event from firmware. It has to be noted that beacon miss event notification for QCN9274 to be handled in a separate patch as it uses STA kickout WMI event to notify beacon miss and the current STA kickout event is processed as low_ack. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Kang Yang <quic_kangyang@quicinc.com> Reviewed-by: Nicolas Escande <nico.escande@gmail.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412094447.2063-1-quic_kangyang@quicinc.com
2024-04-23wifi: ath12k: ACPI band edge channel power supportLingbo Kong4-0/+46
Currently, ath12k does not have the ability to set band edge channel power for WCN7850. In order to support this, ath12k gets band edge channel power table in ath12k_acpi_dsm_get_data() function and sets pdev_id and param_type_id, then finally sends these data and WMI_PDEV_SET_BIOS_INTERFACE_CMDID to firmware to set band edge channel power. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422033054.979-5-quic_lingbok@quicinc.com
2024-04-23wifi: ath12k: ACPI CCA threshold supportLingbo Kong4-0/+47
Currently, ath12k does not have the ability to adjust Clear Channel Assessment (CCA) threshold values to meet the regulatory requirements. Get the values from ACPI and send them to the firmware using ath12k_wmi_set_bios_cmd() function. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422033054.979-4-quic_lingbok@quicinc.com
2024-04-23wifi: ath12k: ACPI SAR supportLingbo Kong5-0/+244
In order to enable ACPI SAR (Specific Absorption Rate), ath12k gets SAR and GEO offset tables from ACPI and sends the data to firmware using WMI_PDEV_SET_BIOS_SAR_TABLE_CMDID and WMI_PDEV_SET_BIOS_GEO_TABLE_CMDID commands. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422033054.979-3-quic_lingbok@quicinc.com
2024-04-23wifi: ath12k: ACPI TAS supportLingbo Kong9-0/+356
Currently, ath12k does not support Time-Average-SAR (TAS). In order to enable TAS read the tables from ACPI and send them to the firmware using WMI_PDEV_SET_BIOS_INTERFACE_CMDID command. Besides, ath12k registers an ACPI event callback so that ACPI can notify ath12k to get the updated SAR power table and sends it to the firmware when the device state is changed. ACPI is only enabled for WCN7850 using struct ath12k_hw_params::acpi_guid field. Most likely QCN9274 will never support ACPI as the chip is not used in laptops. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422033054.979-2-quic_lingbok@quicinc.com
2024-04-23wifi: ath12k: change supports_suspend to true for WCN7850Baochen Qiang1-1/+1
Now that all things are ready, enable supports_suspend to make suspend/resume work for WCN7850. Don't touch other chips because they don't support suspend. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-11-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: support suspend/resumeBaochen Qiang7-32/+134
Now that all infrastructure is in place and ath12k is fixed to handle all the corner cases, power down the ath12k firmware during suspend and power it back up during resume. For suspend, two conditions needs to be satisfied: 1. since MHI channel unprepare would be done in late suspend stage, ath12k needs to get all QMI-dependent things done before that stage. 2. and because unprepare MHI channels requires a working MHI stack, ath12k is not allowed to call mhi_power_down() until that finishes. So the original suspend callback is separated into two parts: the first part handles all QMI-dependent things in suspend callback; while the second part powers down MHI in suspend_late callback. This is valid because kernel calls ath12k's suspend callback before calling all suspend_late callbacks, making the first condition satisfied. And because MHI devices are children of ath12k device (ab->dev), kernel guarantees that ath12k's suspend_late callback is called after QRTR's suspend_late callback, this satisfies the second condition. Above analysis also applies to resume process. so the original resume callback is separated into two parts: the first part powers up MHI stack in resume_early callback, this guarantees MHI stack is working when QRTR tries to prepare MHI channels (kernel calls QRTR's resume_early callback after ath12k's resume_early callback, due to the child-father relationship); the second part waits for the completion of restart, which would succeed since MHI channels are ready for use by QMI. Another notable change is in power down path, we tell mhi_power_down() to not to destroy MHI devices, making it possible for QRTR to help unprepare/prepare MHI channels, and finally get us rid of the potential probe-defer issue when resume. Also change related code due to interface changes. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-10-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: avoid stopping mac80211 queues in ath12k_core_restart()Baochen Qiang1-6/+0
Currently when resume ath12k_core_restart() calls ath12k_core_pre_reconfigure_recovery() where mac80211 queues are stopped by calling ieee80211_stop_queues(). Then in ath12k_mac_op_reconfig_complete() those queues are not started because ieee80211_wake_queues() is skipped due to the check on reconfig_type. The result is that mac80211 could not deliver any frame to ath12k to send out, finally making connection fail. [84473.104249] PM: suspend exit [84479.372397] wlan0: no VHT 160 MHz capability on 5 GHz, limiting to 80 MHz [84479.372401] wlan0: determined local STA to be EHT, BW limited to 80 MHz [84479.372416] wlan0: determined AP 00:03:7f:12:b7:b7 to be HE [84479.372420] wlan0: connecting with HE mode, max bandwidth 80 MHz [84479.580348] wlan0: authenticate with 00:03:7f:12:b7:b7 (local address=00:03:7f:37:11:53) [84479.580351] wlan0: send auth to 00:03:7f:12:b7:b7 (try 1/3) [84480.698993] wlan0: send auth to 00:03:7f:12:b7:b7 (try 2/3) [84481.816505] wlan0: send auth to 00:03:7f:12:b7:b7 (try 3/3) [84482.810966] wlan0: authentication with 00:03:7f:12:b7:b7 timed out Actually we don't need to stop/start queues during suspend/resume, so remove ath12k_core_pre_reconfigure_recovery() from ath12k_core_restart(). This won't cause any regression because currently the only chance ath12k_core_restart() gets called is in reset case, where ab->is_reset is set so that function will never be executed. Also remove ath12k_core_post_reconfigure_recovery() because it is not needed in suspend/resume case. This is also valid due to above analysis. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-9-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: no need to handle pktlog during suspend/resumeBaochen Qiang3-72/+1
Currently pktlog is stopped in suspend callback and started in resume callback, and in either scenarios it's basically to delete/modify ab->mon_reap_timer and to purge related rings. For WCN7850 it's pointless because pktlog is not enabled: both ab->mon_reap_timer and those rings are not initialized. So remove pktlog handling in suspend/resume callbacks. And further, remove these two functions and related callee because no one is calling them. Other chips are not affected because now only WCN7850 supports suspend/resume. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-8-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: flush all packets before suspendBaochen Qiang3-11/+38
In order to send out all packets before going to suspend, current code adds a 500ms delay as a workaround. It is a rough estimate and may not work. Fix this by checking packet counters, if counters become zero, then all packets are sent out or dropped. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-7-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: decrease MHI channel buffer length to 8KBBaochen Qiang1-1/+1
Currently buf_len field of ath12k_mhi_config_wcn7850 is assigned with 0, making MHI use a default size, 64KB, to allocate channel buffers. This is likely to fail in some scenarios where system memory is highly fragmented and memory compaction or reclaim is not allowed. For now we haven't get any failure report on this in ath12k, but there indeed is one such case in ath11k [1]. Actually those buffers are used only by QMI target -> host communication. And for WCN7850, the largest packet size for that is less than 6KB. So change buf_len field to 8KB, which results in order 1 allocation if page size is 4KB. In this way, we can at least save some memory, and as well as decrease the possibility of allocation failure in those scenarios. [1] https://lore.kernel.org/ath11k/96481a45-3547-4d23-ad34-3a8f1d90c1cd@suse.cz/ Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-6-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: fix warning on DMA ring capabilities eventBaochen Qiang1-0/+1
We are seeing below warning in both reset and suspend/resume scenarios: [ 4153.776040] ath12k_pci 0000:04:00.0: Already processed, so ignoring dma ring caps This is because ab->num_db_cap is not cleared in ath12k_wmi_free_dbring_caps(), so clear it to avoid such warnings. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-5-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: do not dump SRNG statistics during resumeBaochen Qiang1-1/+2
Both the firmware reset feature and the power management suspend/resume feature share common power-down and power-up functionality. One aspect of the power-up functionality is the handling of the ATH12K_QMI_EVENT_FW_INIT_DONE event. When this event is received, a call is made to ath12k_hal_dump_srng_stats(), with the purpose to collect information that may be useful in debugging the cause of a firmware reset. Unfortunately, since this functionality is shared between both the firmware reset path and the power management resume path, the kernel log is flooded with messages during resume. Since these messages are not useful during resume, and in fact can be confusing and can increase the time it takes to resume, update the logic to only call ath12k_hal_dump_srng_stats() during firmware reset. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-4-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: remove MHI LOOPBACK channelsBaochen Qiang1-56/+0
There is no driver to match these two channels, so remove them. This fixes warnings from MHI subsystem during suspend: mhi mhi0_LOOPBACK: 1: Failed to reset channel, still resetting mhi mhi0_LOOPBACK: 0: Failed to reset channel, still resetting Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-3-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: rearrange IRQ enable/disable in reset pathBaochen Qiang1-2/+4
For non-WoW suspend/resume, ath12k host powers down whole hardware when suspend and powers up it when resume, the code path it goes through is very like the ath12k reset logic. In order to reuse that logic, rearrange IRQ handling in the reset path. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-2-quic_bqiang@quicinc.com
2024-04-23wifi: ath12k: fix kernel crash during resumeBaochen Qiang3-6/+26
Currently during resume, QMI target memory is not properly handled, resulting in kernel crash in case DMA remap is not supported: BUG: Bad page state in process kworker/u16:54 pfn:36e80 page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x36e80 page dumped because: nonzero _refcount Call Trace: bad_page free_page_is_bad_report __free_pages_ok __free_pages dma_direct_free dma_free_attrs ath12k_qmi_free_target_mem_chunk ath12k_qmi_msg_mem_request_cb The reason is: Once ath12k module is loaded, firmware sends memory request to host. In case DMA remap not supported, ath12k refuses the first request due to failure in allocating with large segment size: ath12k_pci 0000:04:00.0: qmi firmware request memory request ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 7077888 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 8454144 ath12k_pci 0000:04:00.0: qmi dma allocation failed (7077888 B type 1), will try later with small size ath12k_pci 0000:04:00.0: qmi delays mem_request 2 ath12k_pci 0000:04:00.0: qmi firmware request memory request Later firmware comes back with more but small segments and allocation succeeds: ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 262144 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288 ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 65536 ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288 Now ath12k is working. If suspend is triggered, firmware will be reloaded during resume. As same as before, firmware requests two large segments at first. In ath12k_qmi_msg_mem_request_cb() segment count and size are assigned: ab->qmi.mem_seg_count == 2 ab->qmi.target_mem[0].size == 7077888 ab->qmi.target_mem[1].size == 8454144 Then allocation failed like before and ath12k_qmi_free_target_mem_chunk() is called to free all allocated segments. Note the first segment is skipped because its v.addr is cleared due to allocation failure: chunk->v.addr = dma_alloc_coherent() Also note that this leaks that segment because it has not been freed. While freeing the second segment, a size of 8454144 is passed to dma_free_coherent(). However remember that this segment is allocated at the first time firmware is loaded, before suspend. So its real size is 524288, much smaller than 8454144. As a result kernel found we are freeing some memory which is in use and thus crashed. So one possible fix would be to free those segments during suspend. This works because with them freed, ath12k_qmi_free_target_mem_chunk() does nothing: all segment addresses are NULL so dma_free_coherent() is not called. But note that ath11k has similar logic but never hits this issue. Reviewing code there shows the luck comes from QMI memory reuse logic. So the decision is to port it to ath12k. Like in ath11k, the crash is avoided by adding prev_size to target_mem_chunk structure and caching real segment size in it, then prev_size instead of current size is passed to dma_free_coherent(), no unexpected memory is freed now. Also reuse m3 buffer. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240419034034.2842-1-quic_bqiang@quicinc.com
2024-04-22wifi: ath12k: fix out-of-bound access of qmi_invoke_handler()Karthikeyan Kathirvel1-0/+3
Currently, there is no terminator entry for ath12k_qmi_msg_handlers hence facing below KASAN warning, ================================================================== BUG: KASAN: global-out-of-bounds in qmi_invoke_handler+0xa4/0x148 Read of size 8 at addr ffffffd00a6428d8 by task kworker/u8:2/1273 CPU: 0 PID: 1273 Comm: kworker/u8:2 Not tainted 5.4.213 #0 Workqueue: qmi_msg_handler qmi_data_ready_work Call trace: dump_backtrace+0x0/0x20c show_stack+0x14/0x1c dump_stack+0xe0/0x138 print_address_description.isra.5+0x30/0x330 __kasan_report+0x16c/0x1bc kasan_report+0xc/0x14 __asan_load8+0xa8/0xb0 qmi_invoke_handler+0xa4/0x148 qmi_handle_message+0x18c/0x1bc qmi_data_ready_work+0x4ec/0x528 process_one_work+0x2c0/0x440 worker_thread+0x324/0x4b8 kthread+0x210/0x228 ret_from_fork+0x10/0x18 The address belongs to the variable: ath12k_mac_mon_status_filter_default+0x4bd8/0xfffffffffffe2300 [ath12k] [...] ================================================================== Add a dummy terminator entry at the end to assist the qmi_invoke_handler() in traversing up to the terminator entry without accessing an out-of-boundary index. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240416080234.2882725-1-quic_kathirve@quicinc.com
2024-04-22wifi: ath12k: Refactor data path cmem initKarthikeyan Periyasamy1-6/+47
Move the data path Tx and Rx descriptor primary page table CMEM configuration into a helper function. This will make the code more scalable for configuring partner device in support of multi-device MLO. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240411102226.4045323-5-quic_periyasa@quicinc.com
2024-04-22wifi: ath12k: displace the Tx and Rx descriptor in cookie conversion tableKarthikeyan Periyasamy1-2/+2
In the hardware cookie conversion table configuration, place the Rx descriptor at the end. This will allow for easier addition of partner device Rx descriptors in the future to support multi-device MLO. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240411102226.4045323-4-quic_periyasa@quicinc.com
2024-04-22wifi: ath12k: Refactor the hardware cookie conversion initKarthikeyan Periyasamy2-8/+20
Currently, the Rx descriptor is placed before the Tx descriptor in the primary page table of the hardware cookie conversion configuration. The Tx and Rx descriptor offsets are implicitly hardcoded. To allow for easy displacement of Tx and Rx descriptors, introduce Tx and Rx offset based cookie conversion initializationi. Additionally, should consider validating the respective offset ranges while retrieving the Tx and Rx descriptors. This change will be utilize by the next patch in the series. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240411102226.4045323-3-quic_periyasa@quicinc.com
2024-04-22wifi: ath12k: avoid redundant code in Rx cookie conversion initKarthikeyan Periyasamy1-1/+2
Currently, in the Rx data path cookie conversion initialization procedure, the primary page table index (ppt_idx) is computed within the secondary page table iteration. However this is invariant, and hence the ppt_idx should be calculated outside of the iteration to avoid repeated execution of the statement. Found in code review. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240411102226.4045323-2-quic_periyasa@quicinc.com
2024-04-18wifi: ath12k: don't use %pK in dmesg format stringsJeff Johnson6-13/+13
Currently, when debug logs are enabled, messages such as the following are found in the kernel log: event mgmt rx skb pK-error len 209 ftype 00 stype 50 The "pK-error" comes from using %pK to display an skb address in an interrupt context. Per the guidance in the current "printk-formats" documentation, %pK "is only intended when producing content of a file read by userspace from e.g. procfs or sysfs, not for dmesg." So replace %pK with %p in all of the ath12k_dbg() format strings. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240416-pk-v1-1-2c8852743e6d@quicinc.com
2024-04-18wifi: ath12k: enable service flag for survey dump statsThiraviyam Mariyappan2-1/+3
The survey dump statistics does not display channel RX and TX time properly because the survey flag is not enabled in the firmware service flag. If firmware supports enable the service flag "bss_chan_info" in wmi_resource_config to fetch and print the stats for specific pdev. Enabling WMI_RSRC_CFG_FLAG1_BSS_CHANNEL_INFO_64 does not have any impact on WCN7850 since this bit is not utilized by the WCN7850 firmware. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Thiraviyam Mariyappan <quic_tmariyap@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240410085329.3649572-1-quic_kathirve@quicinc.com
2024-04-18wifi: ath12k: enable WIPHY_FLAG_DISABLE_WEXTKalle Valo1-0/+6
ath12k will support Multi-Link Operation (MLO) in the future but not yet. A major change with MLO is that cfg80211 will disable Wireless Extension (WEXT) user space interface. To avoid having inconsistent user experience, first supporting WEXT and later not, disable WEXT already now. Now ath12k claims that WEXT is not supported: $ iwconfig wlan0 wlan0 no wireless extensions. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Link: https://msgid.link/20240411165645.4071238-1-kvalo@kernel.org
2024-04-16wifi: ath12k: dynamically update peer puncturing bitmap for STAKang Yang2-0/+77
Every time EHT Operation element changed, mac80211 will parse it and extract the valid puncturing bitmap according to the bandwidth. Current driver only update puncturing bitmap to firmware as vdev parameter. Which can only meet the needs of AP. But STA will also use it as peer parameter. If only update as vdev parameter, might cause firmware crash. QCN9274 is the same. So update bandwidth and puncturing bitmap as peer parameters once they changed for STA. Then send them to the firmware by WMI event. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Kang Yang <quic_kangyang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240408083047.22548-1-quic_kangyang@quicinc.com
2024-04-16wifi: ath12k: fix mac id extraction when MSDU spillover in rx error pathKarthikeyan Periyasamy1-8/+54
Currently, in the rx error data path, mac id is extracted from the last 64bits of MSDU end description tag for each entry received in the WBM error ring. Then, each entry will be updated into the MSDU list for further processing. The extracted mac id is valid when a single MSDU is not fragmented and received in the WBM error ring. In scenarios where the size of a single MSDU received exceeds the descriptor buffer size, resulting in fragmented or spillover MSDU entries into the WBM error ring. In this case, the extracted mac id from each spillover entry is invalid except the last spillover entry of the MSDU. This invalid mac id leads to packet rejection. To address this issue, check if the MSDU continuation flag is set, then extract the valid mac id from the last spillover entry. Propagate the valid mac id to all the spillover entries of the single MSDU in the temporary MSDU list(scatter_msdu_list). Then, update this into the MSDU list (msdu_list) for further processing. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240404141538.1277258-1-quic_nithp@quicinc.com
2024-04-10wifi: ath12k: support get_survey mac op for single wiphySriram R1-14/+15
The radio for which the survey info needs to be collected depends on the channel idx which could be based on the band. Use the idx to identify the appropriate sband since multiple bands could be combined for single wiphy case. Also use the channel idx and sband to identify the corresponding radio on which the survey results needs to be populated. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-13-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: Modify rts threshold mac op for single wiphySriram R1-4/+14
Since multiple radios are abstracted under a single wiphy, apply the rts threshold value to all the vdevs of the radios combined under single wiphy. This also implies that vif specific rts threshold support needs to be added in future from cfg80211/mac80211. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-12-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: Modify set and get antenna mac ops for single wiphySriram R1-13/+26
As multiple radios are combined into a single wiphy, and the current infrastructure supports only set/get antenna for the wiphy, the max Tx/Rx antenna capability is advertised during wiphy register. Hence, When antenna set/get is received we adjust the set/get based on max radio capability and set/get antenna accordingly. Multi radio capability needs to introduced with interface combination changes to support single wiphy model in cfg80211 which would help extend the wiphy specific get/set configs similar to this to per hw level. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-11-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: modify regulatory support for single wiphy architectureSriram R3-9/+48
With all the radios being combined and registered as a single mac80211 hw/wiphy, separate regd built from firmware rules need not be updated to cfg80211. Rather we can pick one of the regd built from the rules to update to cfg80211 for the whole registered device. We prefer 6 GHz pdev based rules since it has the rules for all bands. If the hw doesn't support 6 GHz, then update rules from one of the pdevs. Also, when regulatory notification is received, update to all the underlying radios/ar so that it becomes aware of the change and as well us it updates its local regd with the new country rules. Later pick the appropriate pdev's regd(6 GHz if available) and apply to cfg80211. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-10-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: Add additional checks for vif and sta iteratorsSriram R4-3/+24
Since vif and sta objects of different radios are added to same local hw list in mac80211, additional checks need to be done in driver to ensure we are processing the intended vif and sta corresponding to the radio when the vif and sta mac80211 iterator utils are used from driver. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-9-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: Cache vdev configs before vdev createSriram R2-34/+147
Since the vdev create for a corresponding vif is deferred until a channel is assigned, cache the information which are received through mac80211 ops between add_interface() and assign_vif_chanctx() and set them once the vdev is created on one of the ath12k radios as the channel gets assigned via assign_vif_chanctx(). Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-8-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: fetch correct radio based on vdev statusSriram R1-11/+64
For ops which passes the vif info, fetch the radio(ar) to be used for corresponding functions based on the the vdev creation status. If the vdev is not created yet, which could happen when the ops are called before channel is assigned for the vif, the data needs to be cached and this is done in followup changes. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-7-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: scan statemachine changes for single wiphySriram R1-38/+176
When multiple radios are advertised as a single wiphy which supports various bands, a default scan request to mac80211 from cfg80211 will split the driver request based on band, so each request will have channels belonging to the same band. With this supported by default, the ath12k driver on receiving this request checks for one of the channels in the request and selects the corresponding radio(ar) on which the scan is going to be performed and creates a vdev on that radio. Note that on scan completion this vdev is not deleted. If a new scan request is seen on that same vif for a different band the vdev will be deleted and created on the new radio supporting the request. The vdev delete logic is refactored to have this done dynamically. The reason for not deleting the vdev on scan stop is to avoid repeated delete-create sequence if the scan is on the same band. Also, during channel assign, new vdev creation can be optimized as well. Also if the scan is requested when the vdev is in started state, no switching to new radio is allowed and scan on channels only within same radio is allowed. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-6-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: vdev statemachine changes for single wiphySriram R3-61/+141
With single wiphy, multiple radios are combined into a single wiphy. Since any channel can be assigned to a vif being brought up, the vdev cannot be created during add_interface(). Hence defer the vdev creation till channel assignment. If only one radio is part of the wiphy, then the existing logic is maintained, i.e vdevs are created during add interface and started during channel assignment. This ensures no functional changes to single pdev devices which has only one radio in the SoC. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-5-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: modify ath12k mac start/stop ops for single wiphySriram R1-12/+31
When mac80211 does drv start/stop, apply the state change for all the radios within the wiphy in ath12k. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-4-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: Modify add and remove chanctx ops for single wiphy supportSriram R2-6/+47
Modify add and remove chanctx mac80211 ops to fetch the correct radio(ar) based on channel context. This change also introduces new helper function to fetch the radio/ar based on channel context and ieee80211_chan which internally uses the radio's low/high freq range. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-3-quic_ramess@quicinc.com
2024-04-10wifi: ath12k: add multiple radio support in a single MAC HW un/registerKarthikeyan Periyasamy3-71/+127
Currently MAC HW un/register helper function support the single radio. To enable single/multi link operation in the future, the following helper functions need to be refactored to accommodate multiple radios under a single MAC HW un/register: * ath12k_ah_to_ar() * ath12k_mac_hw_allocate() * ath12k_mac_hw_register() * ath12k_mac_hw_unregister() This refactoring will make it easier to scale these functionalities and support Multi link operation. Current Multi wiphy Model +---------------+ +---------------+ +---------------+ | Mac80211 hw | | Mac80211 hw | | Mac80211 hw | | private data | | private data | | private data | | | | | | | |ath12k_hw (ah) | |ath12k_hw (ah) | |ath12k_hw (ah) | | | | | | | | +-----------+ | | +-----------+ | | +-----------+ | | | ar (2GHz) | | | | ar (5GHz) | | | | ar (6GHz) | | | +-----------+ | | +-----------+ | | +-----------+ | | | | | | | +---------------+ +---------------+ +---------------+ Single wiphy Model +--------------+ | Mac80211 hw | | private data | | | |ath12k hw (ah)| | +----------+ | | |ar (2GHz) | | | +----------+ | | |ar (5GHz) | | | +----------+ | | |ar (6GHz) | | | +----------+ | +--------------+ Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405194519.1337906-2-quic_ramess@quicinc.com
2024-04-09wifi: ath12k: correct the capital word typoKarthikeyan Periyasamy2-3/+3
Rename the "ATH12k" word to "ATH12K" for consistent capitalization in the word. Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240405144524.1157122-1-quic_periyasa@quicinc.com
2024-04-08wifi: ath12k: fix link capable flagsKarthikeyan Periyasamy1-0/+2
By default driver supports intra-device SLO/MLO, the link capability flags reflect this. When the QMI PHY capability learning fails driver not enable the MLO parameter in the host capability QMI request message. In this case, reset the device link capability flags to zero (SLO/MLO not support) to accurately represent the capabilities. Found in code review. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240403042056.1504209-3-quic_periyasa@quicinc.com
2024-04-08wifi: ath12k: extend the link capable flagKarthikeyan Periyasamy4-6/+23
Link capability categorized as Single Link Operation (SLO) and Multi Link Operation (MLO). - Intra-device SLO/MLO refers to links present within a device - Inter-device SLO/MLO refers to links present across multiple devices Currently, driver uses a boolean variable to represent intra-device SLO/MLO capability. To accommodate inter-device SLO/MLO capabilities within the same variable, modify the existing variable name and type. Define a new enumeration for the link capabilities to accommodate both intra-device and inter-device scenarios. Populate the enum based on the supported capabilities. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240403042056.1504209-2-quic_periyasa@quicinc.com
2024-04-04wifi: ath12k: fix hal_rx_buf_return_buf_manager documentationJeff Johnson1-1/+1
kernel-doc flagged the following issue, so fix it: drivers/net/wireless/ath/ath12k/hal.h:771: warning: missing initial short description on line: * enum hal_rx_buf_return_buf_manager Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240329-hal_rx_buf_return_buf_manager-v1-2-e62ec9dc2af9@quicinc.com
2024-04-04wifi: ath12k: fix missing endianness conversion in wmi_vdev_create_cmd()Miaoqing Pan2-9/+9
The WMI commands are in little endian byte order, fix missing endianness conversion in wmi_vdev_create_cmd. Tested-on: WCN7850 hw2.0 WLAN.IOE_HMT.1.0.2-00240-QCAHMTSWPL_V1.0_V2.0_SILICON-1 Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240322003726.2016208-1-quic_miaoqing@quicinc.com
2024-04-04wifi: ath12k: debugfs: radar simulation supportRamya Gnanasekar1-0/+29
Create dfs_simulate_radar debugfs in ath12k debugfs directory. Usage: echo 1 > /sys/kernel/debug/ath12k/pci-0000:06:00.0/mac0/dfs_simulate_radar This debugfs helps user to simulate RADAR interference in run time. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240320171305.655288-3-quic_rgnanase@quicinc.com
2024-04-04wifi: ath12k: initial debugfs supportRamasamy Kaliappan7-0/+119
The initial debugfs infra bringup in ath12k driver and create the ath12k debugfs and soc-specific directories in /sys/kernel/debug/ For each ath12k device, directory will be created in <bus>-<devname> schema under ath12k root directory. Example with one ath12k device: /sys/kernel/debug/ath12k/pci-0000:06:00.0 ath12k `-- pci-0000:06:00.0 |-- mac0 To enable ath12k debugfs support (CONFIG_ATH12K_DEBUGFS=y) Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com> Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240320171305.655288-2-quic_rgnanase@quicinc.com
Powered by cgit, Gruvboxed by Blaster4385.