aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/marvell/octeontx2/nic/otx2_vf.c
AgeCommit message (Collapse)AuthorFilesLines
2024-05-07net: annotate writes on dev->mtu from ndo_change_mtu()Eric Dumazet1-1/+1
Simon reported that ndo_change_mtu() methods were never updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted in commit 501a90c94510 ("inet: protect against too small mtu values.") We read dev->mtu without holding RTNL in many places, with READ_ONCE() annotations. It is time to take care of ndo_change_mtu() methods to use corresponding WRITE_ONCE() Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Simon Horman <horms@kernel.org> Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/ Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Shannon Nelson <shannon.nelson@amd.com> Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-03-20octeontx2-pf: Wait till detach_resources msg is completeSubbaraya Sundeep1-1/+1
During VF driver remove, a message is sent to detach VF resources to PF but VF is not waiting until message is complete. Also mailbox interrupts need to be turned off after the detach resource message is complete. This patch fixes that problem. Fixes: 05fcc9e08955 ("octeontx2-pf: Attach NIX and NPA block LFs") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-03-20octeontx2: Detect the mbox up or down message via registerSubbaraya Sundeep1-28/+43
A single line of interrupt is used to receive up notifications and down reply messages from AF to PF (similarly from PF to its VF). PF acts as bridge and forwards VF messages to AF and sends respsones back from AF to VF. When an async event like link event is received by up message when PF is in middle of forwarding VF message then mailbox errors occur because PF state machine is corrupted. Since VF is a separate driver or VF driver can be in a VM it is not possible to serialize from the start of communication at VF. Hence to differentiate between type of messages at PF this patch makes sender to set mbox data register with distinct values for up and down messages. Sender also checks whether previous interrupt is received before triggering current interrupt by waiting for mailbox data register to become zero. Fixes: 5a6d7c9daef3 ("octeontx2-pf: Mailbox communication with AF") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-28Merge tag 'net-next-6.5' of ↵Linus Torvalds1-7/+7
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking changes from Jakub Kicinski: "WiFi 7 and sendpage changes are the biggest pieces of work for this release. The latter will definitely require fixes but I think that we got it to a reasonable point. Core: - Rework the sendpage & splice implementations Instead of feeding data into sockets page by page extend sendmsg handlers to support taking a reference on the data, controlled by a new flag called MSG_SPLICE_PAGES Rework the handling of unexpected-end-of-file to invoke an additional callback instead of trying to predict what the right combination of MORE/NOTLAST flags is Remove the MSG_SENDPAGE_NOTLAST flag completely - Implement SCM_PIDFD, a new type of CMSG type analogous to SCM_CREDENTIALS, but it contains pidfd instead of plain pid - Enable socket busy polling with CONFIG_RT - Improve reliability and efficiency of reporting for ref_tracker - Auto-generate a user space C library for various Netlink families Protocols: - Allow TCP to shrink the advertised window when necessary, prevent sk_rcvbuf auto-tuning from growing the window all the way up to tcp_rmem[2] - Use per-VMA locking for "page-flipping" TCP receive zerocopy - Prepare TCP for device-to-device data transfers, by making sure that payloads are always attached to skbs as page frags - Make the backoff time for the first N TCP SYN retransmissions linear. Exponential backoff is unnecessarily conservative - Create a new MPTCP getsockopt to retrieve all info (MPTCP_FULL_INFO) - Avoid waking up applications using TLS sockets until we have a full record - Allow using kernel memory for protocol ioctl callbacks, paving the way to issuing ioctls over io_uring - Add nolocalbypass option to VxLAN, forcing packets to be fully encapsulated even if they are destined for a local IP address - Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure in-kernel ECMP implementation (e.g. Open vSwitch) select the same link for all packets. Support L4 symmetric hashing in Open vSwitch - PPPoE: make number of hash bits configurable - Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client (ipconfig) - Add layer 2 miss indication and filtering, allowing higher layers (e.g. ACL filters) to make forwarding decisions based on whether packet matched forwarding state in lower devices (bridge) - Support matching on Connectivity Fault Management (CFM) packets - Hide the "link becomes ready" IPv6 messages by demoting their printk level to debug - HSR: don't enable promiscuous mode if device offloads the proto - Support active scanning in IEEE 802.15.4 - Continue work on Multi-Link Operation for WiFi 7 BPF: - Add precision propagation for subprogs and callbacks. This allows maintaining verification efficiency when subprograms are used, or in fact passing the verifier at all for complex programs, especially those using open-coded iterators - Improve BPF's {g,s}setsockopt() length handling. Previously BPF assumed the length is always equal to the amount of written data. But some protos allow passing a NULL buffer to discover what the output buffer *should* be, without writing anything - Accept dynptr memory as memory arguments passed to helpers - Add routing table ID to bpf_fib_lookup BPF helper - Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands - Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark maps as read-only) - Show target_{obj,btf}_id in tracing link fdinfo - Addition of several new kfuncs (most of the names are self-explanatory): - Add a set of new dynptr kfuncs: bpf_dynptr_adjust(), bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size() and bpf_dynptr_clone(). - bpf_task_under_cgroup() - bpf_sock_destroy() - force closing sockets - bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs Netfilter: - Relax set/map validation checks in nf_tables. Allow checking presence of an entry in a map without using the value - Increase ip_vs_conn_tab_bits range for 64BIT builds - Allow updating size of a set - Improve NAT tuple selection when connection is closing Driver API: - Integrate netdev with LED subsystem, to allow configuring HW "offloaded" blinking of LEDs based on link state and activity (i.e. packets coming in and out) - Support configuring rate selection pins of SFP modules - Factor Clause 73 auto-negotiation code out of the drivers, provide common helper routines - Add more fool-proof helpers for managing lifetime of MDIO devices associated with the PCS layer - Allow drivers to report advanced statistics related to Time Aware scheduler offload (taprio) - Allow opting out of VF statistics in link dump, to allow more VFs to fit into the message - Split devlink instance and devlink port operations New hardware / drivers: - Ethernet: - Synopsys EMAC4 IP support (stmmac) - Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches - Marvell 88E6250 7 port switches - Microchip LAN8650/1 Rev.B0 PHYs - MediaTek MT7981/MT7988 built-in 1GE PHY driver - WiFi: - Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps - Realtek RTL8723DS (SDIO variant) - Realtek RTL8851BE - CAN: - Fintek F81604 Drivers: - Ethernet NICs: - Intel (100G, ice): - support dynamic interrupt allocation - use meta data match instead of VF MAC addr on slow-path - nVidia/Mellanox: - extend link aggregation to handle 4, rather than just 2 ports - spawn sub-functions without any features by default - OcteonTX2: - support HTB (Tx scheduling/QoS) offload - make RSS hash generation configurable - support selecting Rx queue using TC filters - Wangxun (ngbe/txgbe): - add basic Tx/Rx packet offloads - add phylink support (SFP/PCS control) - Freescale/NXP (enetc): - report TAPRIO packet statistics - Solarflare/AMD: - support matching on IP ToS and UDP source port of outer header - VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6 - add devlink dev info support for EF10 - Virtual NICs: - Microsoft vNIC: - size the Rx indirection table based on requested configuration - support VLAN tagging - Amazon vNIC: - try to reuse Rx buffers if not fully consumed, useful for ARM servers running with 16kB pages - Google vNIC: - support TCP segmentation of >64kB frames - Ethernet embedded switches: - Marvell (mv88e6xxx): - enable USXGMII (88E6191X) - Microchip: - lan966x: add support for Egress Stage 0 ACL engine - lan966x: support mapping packet priority to internal switch priority (based on PCP or DSCP) - Ethernet PHYs: - Broadcom PHYs: - support for Wake-on-LAN for BCM54210E/B50212E - report LPI counter - Microsemi PHYs: support RGMII delay configuration (VSC85xx) - Micrel PHYs: receive timestamp in the frame (LAN8841) - Realtek PHYs: support optional external PHY clock - Altera TSE PCS: merge the driver into Lynx PCS which it is a variant of - CAN: Kvaser PCIEcan: - support packet timestamping - WiFi: - Intel (iwlwifi): - major update for new firmware and Multi-Link Operation (MLO) - configuration rework to drop test devices and split the different families - support for segmented PNVM images and power tables - new vendor entries for PPAG (platform antenna gain) feature - Qualcomm 802.11ax (ath11k): - Multiple Basic Service Set Identifier (MBSSID) and Enhanced MBSSID Advertisement (EMA) support in AP mode - support factory test mode - RealTek (rtw89): - add RSSI based antenna diversity - support U-NII-4 channels on 5 GHz band - RealTek (rtl8xxxu): - AP mode support for 8188f - support USB RX aggregation for the newer chips" * tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits) net: scm: introduce and use scm_recv_unix helper af_unix: Skip SCM_PIDFD if scm->pid is NULL. net: lan743x: Simplify comparison netlink: Add __sock_i_ino() for __netlink_diag_dump(). net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses Revert "af_unix: Call scm_recv() only after scm_set_cred()." phylink: ReST-ify the phylink_pcs_neg_mode() kdoc libceph: Partially revert changes to support MSG_SPLICE_PAGES net: phy: mscc: fix packet loss due to RGMII delays net: mana: use vmalloc_array and vcalloc net: enetc: use vmalloc_array and vcalloc ionic: use vmalloc_array and vcalloc pds_core: use vmalloc_array and vcalloc gve: use vmalloc_array and vcalloc octeon_ep: use vmalloc_array and vcalloc net: usb: qmi_wwan: add u-blox 0x1312 composition perf trace: fix MSG_SPLICE_PAGES build error ipvlan: Fix return value of ipvlan_queue_xmit() netfilter: nf_tables: fix underflow in chain reference counter netfilter: nf_tables: unbind non-anonymous set if rule construction fails ...
2023-05-15octeontx2-pf: Add support for HTB offloadNaveen Mamindlapalli1-0/+1
This patch registers callbacks to support HTB offload. Below are features supported, - supports traffic shaping on the given class by honoring rate and ceil configuration. - supports traffic scheduling, which prioritizes different types of traffic based on strict priority values. - supports the creation of leaf to inner classes such that parent node rate limits apply to all child nodes. Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com> Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-05-15octeontx2-pf: Refactor schedular queue alloc/free callsHariprasad Kelam1-4/+0
1. Upon txschq free request, the transmit schedular config in hardware is not getting reset. This patch adds necessary changes to do the same. 2. Current implementation calls txschq alloc during interface initialization and in response handler updates the default txschq array. This creates a problem for htb offload where txsch alloc will be called for every tc class. This patch addresses the issue by reading txschq response in mbox caller function instead in the response handler. 3. Current otx2_txschq_stop routine tries to free all txschq nodes allocated to the interface. This creates a problem for htb offload. This patch introduces the otx2_txschq_free_one to free txschq in a given level. Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-05-15octeontx2-pf: qos send queues managementSubbaraya Sundeep1-2/+5
Current implementation is such that the number of Send queues (SQs) are decided on the device probe which is equal to the number of online cpus. These SQs are allocated and deallocated in interface open and c lose calls respectively. This patch defines new APIs for initializing and deinitializing Send queues dynamically and allocates more number of transmit queues for QOS feature. Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-05-15octeontx2-pf: Rename tot_tx_queues to non_qos_queuesHariprasad Kelam1-1/+1
current implementation is such that tot_tx_queues contains both xdp queues and normal tx queues. which will be allocated in interface open calls and deallocated on interface down calls respectively. With addition of QOS, where send quees are allocated/deallacated upon user request Qos send queues won't be part of tot_tx_queues. So this patch renames tot_tx_queues to non_qos_queues. Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-05-08net: octeontx2: Use alloc_ordered_workqueue() to create ordered workqueuesTejun Heo1-3/+2
BACKGROUND ========== When multiple work items are queued to a workqueue, their execution order doesn't match the queueing order. They may get executed in any order and simultaneously. When fully serialized execution - one by one in the queueing order - is needed, an ordered workqueue should be used which can be created with alloc_ordered_workqueue(). However, alloc_ordered_workqueue() was a later addition. Before it, an ordered workqueue could be obtained by creating an UNBOUND workqueue with @max_active==1. This originally was an implementation side-effect which was broken by 4c16bd327c74 ("workqueue: restore WQ_UNBOUND/max_active==1 to be ordered"). Because there were users that depended on the ordered execution, 5c0338c68706 ("workqueue: restore WQ_UNBOUND/max_active==1 to be ordered") made workqueue allocation path to implicitly promote UNBOUND workqueues w/ @max_active==1 to ordered workqueues. While this has worked okay, overloading the UNBOUND allocation interface this way creates other issues. It's difficult to tell whether a given workqueue actually needs to be ordered and users that legitimately want a min concurrency level wq unexpectedly gets an ordered one instead. With planned UNBOUND workqueue updates to improve execution locality and more prevalence of chiplet designs which can benefit from such improvements, this isn't a state we wanna be in forever. This patch series audits all callsites that create an UNBOUND workqueue w/ @max_active==1 and converts them to alloc_ordered_workqueue() as necessary. WHAT TO LOOK FOR ================ The conversions are from alloc_workqueue(WQ_UNBOUND | flags, 1, args..) to alloc_ordered_workqueue(flags, args...) which don't cause any functional changes. If you know that fully ordered execution is not ncessary, please let me know. I'll drop the conversion and instead add a comment noting the fact to reduce confusion while conversion is in progress. If you aren't fully sure, it's completely fine to let the conversion through. The behavior will stay exactly the same and we can always reconsider later. As there are follow-up workqueue core changes, I'd really appreciate if the patch can be routed through the workqueue tree w/ your acks. Thanks. Signed-off-by: Tejun Heo <tj@kernel.org> Reviewed-by: Sunil Goutham <sgoutham@marvell.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Ratheesh Kannoth <rkannoth@marvell.com> Cc: Srujana Challa <schalla@marvell.com> Cc: Geetha sowjanya <gakula@marvell.com> Cc: netdev@vger.kernel.org
2023-05-03octeontx2-vf: Detach LF resources on probe cleanupSubbaraya Sundeep1-1/+1
When a VF device probe fails due to error in MSIX vector allocation then the resources NIX and NPA LFs were not detached. Fix this by detaching the LFs when MSIX vector allocation fails. Fixes: 3184fb5ba96e ("octeontx2-vf: Virtual function driver support") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-03-20octeontx2-vf: Add missing free for alloc_percpuJiasheng Jiang1-0/+2
Add the free_percpu for the allocated "vf->hw.lmt_info" in order to avoid memory leak, same as the "pf->hw.lmt_info" in `drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c`. Fixes: 5c0512072f65 ("octeontx2-pf: cn10k: Use runtime allocated LMTLINE region") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Acked-by: Geethasowjanya Akula <gakula@marvell.com> Link: https://lore.kernel.org/r/20230317064337.18198-1-jiasheng@iscas.ac.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-01-10octeontx2-pf: Fix resource leakage in VF driver unbindHariprasad Kelam1-0/+2
resources allocated like mcam entries to support the Ntuple feature and hash tables for the tc feature are not getting freed in driver unbind. This patch fixes the issue. Fixes: 2da489432747 ("octeontx2-pf: devlink params support to set mcam entry count") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Link: https://lore.kernel.org/r/20230109061325.21395-1-hkelam@marvell.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-05-06net: make drivers set the TSO limit not the GSO limitJakub Kicinski1-1/+1
Drivers should call the TSO setting helper, GSO is controllable by user space. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-23octeontx2-pf: Vary completion queue event sizeSubbaraya Sundeep1-0/+2
Completion Queue Entry(CQE) is a descriptor written by hardware to notify software about the send and receive completion status. The CQE can be of size 128 or 512 bytes. A 512 bytes CQE can hold more receive fragments pointers compared to 128 bytes CQE. This patch enables to modify CQE size using: <ethtool -G cqe-size N>. Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-10octeontx2-pf: Add TC feature for VFsSubbaraya Sundeep1-19/+11
This patch adds TC feature for VFs also. When MCAM rules are allocated for a VF then either TC or ntuple filters can be used. Below are the commands to use TC feature for a VF(say lbk0): devlink dev param set pci/0002:01:00.1 name mcam_count value 16 \ cmode runtime ethtool -K lbk0 hw-tc-offload on ifconfig lbk0 up tc qdisc add dev lbk0 ingress tc filter add dev lbk0 parent ffff: protocol ip flower skip_sw \ dst_mac 98:03:9b:83:aa:12 action police rate 100Mbit burst 5000 Also to modify any fields of the hardware context with NIX_AQ_INSTOP_WRITE command then corresponding masks of those fields must be set as per hardware. This was missing in ingress ratelimiting context. This patch sets those masks also. Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-09octeontx2-pf: PFC config support with DCBxHariprasad Kelam1-0/+14
Data centric bridging designed to eliminate packet loss due to queue overflow by adding enhancements to ethernet network such as proprity flow control etc. This patch adds support for management of Priority flow control(PFC) on Octeontx2 and CN10K interfaces. To enable PFC for all priorities dcb pfc set dev eth0 prio-pfc all:on/off To enable PFC on selected priorites dcb pfc set dev eth0 prio-pfc 0:on/off 1:on/off ..7:on/off With the ntuple commands user can map Priority to receive queues. On queue overflow NIX will assert backpressure such that PFC pause frames are genarated with mapped priority. To map priority 7 to Queue 1 ethtool -U eth0 flow-type ether dst xx:xx:xx:xx:xx:xx vlan 0xe00a m 0x1fff queue 1 Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-09octeontx2-af: Don't enable Pause frames by defaultHariprasad Kelam1-4/+8
Current implementation is such that 802.3x pause frames are enabled by default. As CGX and RPM blocks support PFC (priority flow control) also, instead of driver enabling one between them enable them upon request from PF or its VFs. Also add support to disable pause frames in driver unbind. Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-28octeontx2-pf: Change receive buffer size using ethtoolSubbaraya Sundeep1-0/+1
ethtool rx-buf-len is for setting receive buffer size, support setting it via ethtool -G parameter and getting it via ethtool -g parameter. Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-1/+4
Merge in fixes directly in prep for the 5.17 merge window. No conflicts. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-01-07octeontx2-nicvf: Free VF PTP resources.Rakesh Babu Saladi1-1/+4
When a VF is removed respective PTP resources are not being freed currently. This patch fixes it. Fixes: 43510ef4ddad ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF") Signed-off-by: Rakesh Babu Saladi <rsaladi2@marvell.com> Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-22net: annotate accesses to dev->gso_max_segsEric Dumazet1-1/+1
dev->gso_max_segs is written under RTNL protection, or when the device is not yet visible, but is read locklessly. Add netif_set_gso_max_segs() helper. Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_segs() where we can to better document what is going on. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-05octeontx2-nicvf: fix ioctl callbackArnd Bergmann1-1/+1
The mii ioctls are now handled by the ndo_eth_ioctl() callback, not the old ndo_do_ioctl(), but octeontx2-nicvf introduced the function for the old way. Move it over to ndo_eth_ioctl() to actually allow calling it from user space. Fixes: 43510ef4ddad ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF") Fixes: a76053707dbf ("dev_ioctl: split out ndo_eth_ioctl") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-10ethernet: Remove redundant 'flush_workqueue()' callsChristophe JAILLET1-1/+0
'destroy_workqueue()' already drains the queue before destroying it, so there is no need to flush it explicitly. Remove the redundant 'flush_workqueue()' calls. This was generated with coccinelle: @@ expression E; @@ - flush_workqueue(E); destroy_workqueue(E); Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> #mlx* Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-30octeontx2-pf: Add XDP support to netdev PFGeetha sowjanya1-0/+1
Adds XDP_PASS, XDP_TX, XDP_DROP and XDP_REDIRECT support for netdev PF. Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-29octeontx2-nicvf: Add PTP hardware clock support to NIX VFNaveen Mamindlapalli1-0/+6
This patch adds PTP PHC support to NIX VF interfaces. This enables a VF to run PTP master/slave instance. PTP block being a shared hardware resource it is recommended to avoid running multiple PTP instances in the system which will impact the PTP clock accuracy. Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com> Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-29octeontx2-pf: Fix inconsistent license textSunil Goutham1-1/+5
Fixed inconsistent license text across the netdev drivers. Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-17octeontx2-pf: devlink params support to set mcam entry countSunil Goutham1-0/+5
Added support for setting or modifying MCAM entry count at runtime via devlink params. commands: devlink dev param show pci/0002:02:00.0: name mcam_count type driver-specific values: cmode runtime value 16 devlink dev param set pci/0002:02:00.0 name mcam_count value 64 cmode runtime Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-17octeontx2-pf: Ntuple filters support for VF netdevRakesh Babu1-0/+28
Add packet flow classification support for both LMAC mapped virtual functions and loopback VFs. This patch adds supports for ntuple offload feature. Signed-off-by: Rakesh Babu <rsaladi2@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-17octeontx2-pf: Enable NETIF_F_RXALL support for VF driverSunil Goutham1-1/+2
Enabled NETIF_F_RXALL support for VF driver. Also removed MTU range comments which are no longer valid. Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-01octeontx2-pf: cn10k: Use runtime allocated LMTLINE regionGeetha sowjanya1-7/+5
The current driver uses static LMTST region allocated by firmware. This memory gets populated as PF/VF BAR2. RVU PF/VF driver ioremap the memory as device memory for NIX/NPA operation. Since the memory is mapped as device memory we see performance degration. To address this issue this patch implements runtime memory allocation. RVU PF/VF allocates memory during device probe and share the base address with RVU AF. RVU AF then configure the LMT MAP table accordingly. Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-11octeontx2-nicvf: add ndo_set_rx_mode support for multicast & promiscNaveen Mamindlapalli1-2/+56
Add ndo_set_rx_mode callback handler to configure promisc, multicast and allmulti options for VF driver. Also, modified PF driver ndo_set_rx_mode handler to support multicast and promisc mode independently. Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-11octeontx2-pf: cn10k: Get max mtu supported from admin functionHariprasad Kelam1-1/+1
CN10K supports max MTU of 16K on LMAC links and 64k on LBK links and Octeontx2 silicon supports 9K mtu on both links. Get the same from nix_get_hw_info mbox message in netdev probe. This patch also calculates receive buffer size required based on the MTU set. Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-11octeontx2-pf: cn10k: Use LMTST lines for NPA/NIX operationsGeetha sowjanya1-26/+2
This patch adds support to use new LMTST lines for NPA batch free and burst SQE flush. Adds new dev_hw_ops structure to hold platform specific functions and create new files cn10k.c and cn10k.h. Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-11octeontx2-pf: cn10k: Map LMTST regionGeetha sowjanya1-2/+35
On CN10K platform transmit/receive buffer alloc and free from/to hardware had changed to support burst operation. Whereas pervious silicon's only support single buffer free at a time. To Support the same firmware allocates a DRAM region for each PF/VF for storing LMTLINES. These LMTLINES are used for NPA batch free and for flushing SQE to the hardware. PF/VF LMTST region is accessed via BAR4. PFs LMTST region is followed by its VFs mbox memory. The size of region varies from 2KB to 256KB based on number of LMTLINES configured. This patch adds support for - Mapping PF/VF LMTST region. - Reserves 0-71 (RX + TX + XDP) LMTST lines for NPA batch free operation. - Reserves 72-512 LMTST lines for NIX SQE flush. Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-11octeontx2-pf: cn10k: Add mbox support for CN10KSubbaraya Sundeep1-13/+24
Firmware allocates memory regions for PFs and VFs in DRAM. The PFs memory region is used for AF-PF and PF-VF mailbox. This mbox facilitate communication between AF-PF and PF-VF. On CN10K platform: The DRAM region allocated to PF is enumerated as PF BAR4 memory. PF BAR4 contains AF-PF mbox region followed by its VFs mbox region. AF-PF mbox region base address is configured at RVU_AF_PFX_BAR4_ADDR PF-VF mailbox base address is configured at RVU_PF(x)_VF_MBOX_ADDR = RVU_AF_PF()_BAR4_ADDR+64KB. PF access its mbox region via BAR4, whereas VF accesses PF-VF DRAM mailboxes via BAR2 indirect access. On CN9XX platform: Mailbox region in DRAM is divided into two parts AF-PF mbox region and PF-VF mbox region i.e all PFs mbox region is contiguous similarly all VFs. The base address of the AF-PF mbox region is configured at RVU_AF_PF_BAR4_ADDR. AF-PF1 mbox address can be calculated as RVU_AF_PF_BAR4_ADDR * mbox size. The base address of PF-VF mbox region for each PF is configure at RVU_AF_PF(0..15)_VF_BAR4_ADDR.PF access its mbox region via BAR4 and its VF mbox regions from RVU_PF_VF_BAR4_ADDR register, whereas VF access its mbox region via BAR4. This patch changes mbox initialization to support both CN9XX and CN10K platform. The patch also adds new hw_cap flag to setting hw features like TSO etc and removes platform specific name from the PF/VF driver name to make it appropriate for all supported platforms This patch also removes platform specific name from the PF/VF driver name to make it appropriate for all supported platforms Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-11-17octeontx2-pf: Implement ingress/egress VLAN offloadHariprasad Kelam1-0/+5
This patch implements egress VLAN offload by appending NIX_SEND_EXT_S header to NIX_SEND_HDR_S. The VLAN TCI information is specified in the NIX_SEND_EXT_S. The VLAN offload in the ingress path is implemented by configuring the NIX_RX_VTAG_ACTION_S to strip and capture the outer vlan fields. The NIX PF allocates one MCAM entry for Rx VLAN offload. Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller1-2/+2
Rejecting non-native endian BTF overlapped with the addition of support for it. The rest were more simple overlapping changes, except the renesas ravb binding update, which had to follow a file move as well as a YAML conversion. Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-30octeontx2-pf: Fix synchnorization issue in mboxHariprasad Kelam1-2/+2
Mbox implementation in octeontx2 driver has three states alloc, send and reset in mbox response. VF allocate and sends message to PF for processing, PF ACKs them back and reset the mbox memory. In some case we see synchronization issue where after msgs_acked is incremented and before mbox_reset API is called, if current execution is scheduled out and a different thread is scheduled in which checks for msgs_acked. Since the new thread sees msgs_acked == msgs_sent it will try to allocate a new message and to send a new mbox message to PF.Now if mbox_reset is scheduled in, PF will see '0' in msgs_send. This patch fixes the issue by calling mbox_reset before incrementing msgs_acked flag for last processing message and checks for valid message size. Fixes: d424b6c02 ("octeontx2-pf: Enable SRIOV and added VF mbox handling") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-23octeontx2-pf: Add tracepoints for PF/VF mailboxSubbaraya Sundeep1-0/+2
With tracepoints support present in the mailbox code this patch adds tracepoints in PF and VF drivers at places where mailbox messages are allocated, sent and at message interrupts. Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-01octeontx2-pf: Add UDP segmentation offload supportSunil Goutham1-1/+2
Defines UDP segmentation algorithm in hardware and supports offloading UDP segmentation. Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28octeontx2-pf: Unregister netdev at driver removeSubbaraya Sundeep1-0/+1
Added unregister_netdev in the driver remove function. Generally unregister_netdev is called after disabling all the device interrupts but here it is called before disabling device mailbox interrupts. The reason behind this is VF needs mailbox interrupt to communicate with its PF to clean up its resources during otx2_stop. otx2_stop disables packet I/O and queue interrupts first and by using mailbox interrupt communicates to PF to free VF resources. Hence this patch calls unregister_device just before disabling mailbox interrupts. Fixes: 3184fb5ba96e ("octeontx2-vf: Virtual function driver support") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28octeontx2-pf: cancel reset_task workSubbaraya Sundeep1-0/+1
During driver exit cancel the queued reset_task work in VF driver. Fixes: 3184fb5ba96e ("octeontx2-vf: Virtual function driver support") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-08octeontx2-vf: Fix error return code in otx2vf_probe()Wei Yongjun1-2/+6
Fix to return negative error code -ENOMEM from the alloc failed error handling case instead of 0, as done elsewhere in this function. Fixes: 3184fb5ba96e ("octeontx2-vf: Virtual function driver support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-03-23octeontx2-pf: Remove wrapper APIs for mutex lock and unlockSunil Goutham1-1/+1
This patch removes wrapper fn()s around mutex_init/lock/unlock. Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-23octeontx2-vf: Ethtool supportTomasz Duszynski1-0/+2
Added ethtool support for VF devices for - Driver stats, Tx/Rx perqueue stats - Set/show Rx/Tx queue count - Set/show Rx/Tx ring sizes - Set/show IRQ coalescing parameters - RSS configuration etc It's the PF which owns the interface, hence VF cannot display underlying CGX interface stats. Except for this rest ethtool support reuses PF's APIs. Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-23octeontx2-vf: Virtual function driver supportTomasz Duszynski1-0/+646
On OcteonTx2 silicon there two two types VFs, VFs that share the physical link with their parent SR-IOV PF and the VFs which work in pairs using internal HW loopback channels (LBK). Except for the underlying Rx/Tx channel mapping from netdev functionality perspective they are almost identical. This patch adds netdev driver support for these VFs. Unlike it's parent PF a VF cannot directly communicate with admin function (AF) and it has to go through PF for the same. The mailbox communication with AF works like 'VF <=> PF <=> AF'. Also functionality wise VF and PF are identical, hence to avoid code duplication PF driver's APIs are resued here for HW initialization, packet handling etc etc ie almost everything. For VF driver to compile as module exported few of the existing PF driver APIs. Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Powered by cgit, Gruvboxed by Blaster4385.