| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <[email protected]>
|
|
Simplify the return expression.
Signed-off-by: Qinglang Miao <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/intel/e1000/e1000_hw.c: In function e1000_phy_init_script:
drivers/net/ethernet/intel/e1000/e1000_hw.c:132:6: warning: variable ‘ret_val’ set but not used [-Wunused-but-set-variable]
`ret_val` is never used, so remove it.
Signed-off-by: Zheng Yongjun <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pass the region to be snapshotted to the function performing the
snapshot. This allows one function to operate on numerous regions.
v4:
Add missing kerneldoc for ICE
Signed-off-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Report standard pause frame stats. They are already aggregated
in struct ixgbe_hw_stats.
The combination of the registers is suggested as equivalent to
PAUSEMACCtrlFramesTransmitted / PAUSEMACCtrlFramesReceived
by the Intel 82576EB datasheet, I could not find any information
in the HW actually supported by ixgbe.
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Alexander Duyck <[email protected]>
Reviewed-by: Saeed Mahameed <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Instead of checking in each iteration of the Rx packet processing
loop, move the allocation out of the loop and do it once for each napi
activation.
For AF_XDP the rx_drop benchmark was improved by 6%.
Signed-off-by: Björn Töpel <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The i40e NIC supports two flavors of HW descriptors, 16 and 32
byte. The latter has, obviously, room for more offloading
information. However, the only fields of the 32B HW descriptor that is
being used by the driver, is also available in the 16B descriptor.
In other words; Reading and writing 32 bytes instead of 16 byte is a
waste of bus bandwidth.
This commit starts using 16 byte descriptors instead of 32 byte
descriptors.
For AF_XDP the rx_drop benchmark was improved by 2%.
Signed-off-by: Björn Töpel <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The software prefetching of HW descriptors has a negative impact on
the performance. Therefore, it is now removed.
Performance for the rx_drop benchmark increased with 2%.
Signed-off-by: Björn Töpel <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
refcount of rx_buffer page will be added here originally, so prefetchw
is needed, but after commit 1793668c3b8c ("i40e/i40evf: Update code to
better handle incrementing page count"), and refcount is not added
every time, so change prefetchw as prefetch.
Now it mainly services page_address(), but which accesses struct page
only when WANT_PAGE_VIRTUAL or HASHED_PAGE_VIRTUAL is defined otherwise
it returns address based on offset, so we prefetch it conditionally.
Jakub suggested to define prefetch_page_address in a common header.
Reported-by: kernel test robot <[email protected]>
Suggested-by: Jakub Kicinski <[email protected]>
Signed-off-by: Li RongQing <[email protected]>
Reviewed-by: Jesse Brandeburg <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
After commit 759dc4a7e605 ("i40e: initialize our affinity_mask
based on cpu_possible_mask"), NAPI IRQ affinity_mask is bind to
all possible CPUs, not a fixed CPU
Signed-off-by: Li RongQing <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
We allow drivers to call napi_hash_del() before calling
netif_napi_del() to batch RCU grace periods. This makes
the API asymmetric and leaks internal implementation details.
Soon we will want the grace period to protect more than just
the NAPI hash table.
Restructure the API and have drivers call a new function -
__netif_napi_del() if they want to take care of RCU waits.
Note that only core was checking the return status from
napi_hash_del() so the new helper does not report if the
NAPI was actually deleted.
Some notes on driver oddness:
- veth observed the grace period before calling netif_napi_del()
but that should not matter
- myri10ge observed normal RCU flavor
- bnx2x and enic did not actually observe the grace period
(unless they did so implicitly)
- virtio_net and enic only unhashed Rx NAPIs
The last two points seem to indicate that the calls to
napi_hash_del() were a left over rather than an optimization.
Regardless, it's easy enough to correct them.
This patch may introduce extra synchronize_net() calls for
interfaces which set NAPI_STATE_NO_BUSY_POLL and depend on
free_netdev() to call netif_napi_del(). This seems inevitable
since we want to use RCU for netpoll dev->napi_list traversal,
and almost no drivers set IFF_DISABLE_NETPOLL.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When timestamping a packet there's a delay between the start of the
packet and the point where the hardware actually captures the
timestamp. This difference needs to be considered if we want accurate
timestamps.
This was done on the RX side, but not on the TX side.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The previous timestamping latency numbers were obtained by
interpolating the i210 numbers with the i225 crystal clock value. That
calculation was wrong.
Use the correct values from real measurements.
Fixes: 81b055205e8b ("igc: Add support for RX timestamping")
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The for loop in i40e_set_vsi_promisc() reports errors via dev_err() but
does not propagate the error up the call chain. Instead it continues the
loop and potentially overwrites the reported error value.
This results in the error being recorded in the log buffer, but the
caller might never know anything went the wrong way.
To avoid this situation i40e_set_vsi_promisc() needs to temporarily store
the error after reporting it. This is still not optimal as multiple
different errors may occur, so store the first error and hope that's
the main issue.
Fixes: 37d318d7805f (i40e: Remove scheduling while atomic possibility)
Reported-by: Michal Schmidt <[email protected]>
Signed-off-by: Stefan Assmann <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c: In function ‘i40e_set_vsi_promisc’:
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1176:14: error: ‘aq_ret’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
i40e_status aq_ret;
In case the code inside the if statement and the for loop does not get
executed aq_ret will be uninitialized when the variable gets returned at
the end of the function.
Avoid this by changing num_vlans from int to u16, so aq_ret always gets
set. Making this change in additional places as num_vlans should never
be negative.
Fixes: 37d318d7805f ("i40e: Remove scheduling while atomic possibility")
Signed-off-by: Stefan Assmann <[email protected]>
Acked-by: Jakub Kicinski <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444a4 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-09-01
The following pull-request contains BPF updates for your *net-next* tree.
There are two small conflicts when pulling, resolve as follows:
1) Merge conflict in tools/lib/bpf/libbpf.c between 88a82120282b ("libbpf: Factor
out common ELF operations and improve logging") in bpf-next and 1e891e513e16
("libbpf: Fix map index used in error message") in net-next. Resolve by taking
the hunk in bpf-next:
[...]
scn = elf_sec_by_idx(obj, obj->efile.btf_maps_shndx);
data = elf_sec_data(obj, scn);
if (!scn || !data) {
pr_warn("elf: failed to get %s map definitions for %s\n",
MAPS_ELF_SEC, obj->path);
return -EINVAL;
}
[...]
2) Merge conflict in drivers/net/ethernet/mellanox/mlx5/core/en/xsk/rx.c between
9647c57b11e5 ("xsk: i40e: ice: ixgbe: mlx5: Test for dma_need_sync earlier for
better performance") in bpf-next and e20f0dbf204f ("net/mlx5e: RX, Add a prefetch
command for small L1_CACHE_BYTES") in net-next. Resolve the two locations by retaining
net_prefetch() and taking xsk_buff_dma_sync_for_cpu() from bpf-next. Should look like:
[...]
xdp_set_data_meta_invalid(xdp);
xsk_buff_dma_sync_for_cpu(xdp, rq->xsk_pool);
net_prefetch(xdp->data);
[...]
We've added 133 non-merge commits during the last 14 day(s) which contain
a total of 246 files changed, 13832 insertions(+), 3105 deletions(-).
The main changes are:
1) Initial support for sleepable BPF programs along with bpf_copy_from_user() helper
for tracing to reliably access user memory, from Alexei Starovoitov.
2) Add BPF infra for writing and parsing TCP header options, from Martin KaFai Lau.
3) bpf_d_path() helper for returning full path for given 'struct path', from Jiri Olsa.
4) AF_XDP support for shared umems between devices and queues, from Magnus Karlsson.
5) Initial prep work for full BPF-to-BPF call support in libbpf, from Andrii Nakryiko.
6) Generalize bpf_sk_storage map & add local storage for inodes, from KP Singh.
7) Implement sockmap/hash updates from BPF context, from Lorenz Bauer.
8) BPF xor verification for scalar types & add BPF link iterator, from Yonghong Song.
9) Use target's prog type for BPF_PROG_TYPE_EXT prog verification, from Udip Pant.
10) Rework BPF tracing samples to use libbpf loader, from Daniel T. Lee.
11) Fix xdpsock sample to really cycle through all buffers, from Weqaar Janjua.
12) Improve type safety for tun/veth XDP frame handling, from Maciej Żenczykowski.
13) Various smaller cleanups and improvements all over the place.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
performance
Test for dma_need_sync earlier to increase
performance. xsk_buff_dma_sync_for_cpu() takes an xdp_buff as
parameter and from that the xsk_buff_pool reference is dug out. Perf
shows that this dereference causes a lot of cache misses. But as the
buffer pool is now sent down to the driver at zero-copy initialization
time, we might as well use this pointer directly, instead of going via
the xsk_buff and we can do so already in xsk_buff_dma_sync_for_cpu()
instead of in xp_dma_sync_for_cpu. This gets rid of these cache
misses.
Throughput increases with 3% for the xdpsock l2fwd sample application
on my machine.
Signed-off-by: Magnus Karlsson <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Björn Töpel <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Rename the AF_XDP zero-copy driver interface functions to better
reflect what they do after the replacement of umems with buffer
pools in the previous commit. Mostly it is about replacing the
umem name from the function names with xsk_buff and also have
them take the a buffer pool pointer instead of a umem. The
various ring functions have also been renamed in the process so
that they have the same naming convention as the internal
functions in xsk_queue.h. This so that it will be clearer what
they do and also for consistency.
Signed-off-by: Magnus Karlsson <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Björn Töpel <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.
Signed-off-by: Magnus Karlsson <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Björn Töpel <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Many device drivers use the same prefetch code structure to
deal with small L1 cacheline size.
Take this code into a function and call it from the drivers.
Suggested-by: Jakub Kicinski <[email protected]>
Signed-off-by: Tariq Toukan <[email protected]>
Reviewed-by: Saeed Mahameed <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"23 fixes in 5 drivers (qla2xxx, ufs, scsi_debug, fcoe, zfcp). The bulk
of the changes are in qla2xxx and ufs and all are mostly small and
definitely don't impact the core"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (23 commits)
Revert "scsi: qla2xxx: Disable T10-DIF feature with FC-NVMe during probe"
Revert "scsi: qla2xxx: Fix crash on qla2x00_mailbox_command"
scsi: qla2xxx: Fix null pointer access during disconnect from subsystem
scsi: qla2xxx: Check if FW supports MQ before enabling
scsi: qla2xxx: Fix WARN_ON in qla_nvme_register_hba
scsi: qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime
scsi: qla2xxx: Reduce noisy debug message
scsi: qla2xxx: Fix login timeout
scsi: qla2xxx: Indicate correct supported speeds for Mezz card
scsi: qla2xxx: Flush I/O on zone disable
scsi: qla2xxx: Flush all sessions on zone disable
scsi: qla2xxx: Use MBX_TOV_SECONDS for mailbox command timeout values
scsi: scsi_debug: Fix scp is NULL errors
scsi: zfcp: Fix use-after-free in request timeout handlers
scsi: ufs: No need to send Abort Task if the task in DB was cleared
scsi: ufs: Clean up completed request without interrupt notification
scsi: ufs: Improve interrupt handling for shared interrupts
scsi: ufs: Fix interrupt error message for shared interrupts
scsi: ufs-pci: Add quirk for broken auto-hibernate for Intel EHL
scsi: ufs-mediatek: Fix incorrect time to wait link status
...
|
|
ixgbe_fcoe_ddp_setup() can be called from the main I/O path and is called
with a spin_lock held, so we have to use GFP_ATOMIC allocation instead of
GFP_KERNEL.
Link: https://lore.kernel.org/r/[email protected]
cc: Hannes Reinecke <[email protected]>
Reviewed-by: Lee Duncan <[email protected]>
Signed-off-by: Mike Christie <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Fix the reason of crashing system by add waiting time to finish reset
recovery process before starting remove driver procedure.
Now VSI is releasing if VSI is not in reset recovery mode.
Without this fix it was possible to start remove driver if other
processing command need reset recovery procedure which resulted in
null pointer dereference. VSI used by the ethtool process has been
cleared by remove driver process.
[ 6731.508665] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 6731.508668] #PF: supervisor read access in kernel mode
[ 6731.508670] #PF: error_code(0x0000) - not-present page
[ 6731.508671] PGD 0 P4D 0
[ 6731.508674] Oops: 0000 [#1] SMP PTI
[ 6731.508679] Hardware name: Intel Corporation S2600WT2R/S2600WT2R, BIOS SE5C610.86B.01.01.0021.032120170601 03/21/2017
[ 6731.508694] RIP: 0010:i40e_down+0x252/0x310 [i40e]
[ 6731.508696] Code: c7 78 de fa c0 e8 61 02 3a c1 66 83 bb f6 0c 00 00 00 0f 84 bf 00 00 00 45 31 e4 45 31 ff eb 03 41 89 c7 48 8b 83 98 0c 00 00 <4a> 8b 3c 20 e8 a5 79 02 00 48 83 bb d0 0c 00 00 00 74 10 48 8b 83
[ 6731.508698] RSP: 0018:ffffb75ac7b3faf0 EFLAGS: 00010246
[ 6731.508700] RAX: 0000000000000000 RBX: ffff9c9874bd5000 RCX: 0000000000000007
[ 6731.508701] RDX: 0000000000000000 RSI: 0000000000000096 RDI: ffff9c987f4d9780
[ 6731.508703] RBP: ffffb75ac7b3fb30 R08: 0000000000005b60 R09: 0000000000000004
[ 6731.508704] R10: ffffb75ac64fbd90 R11: 0000000000000001 R12: 0000000000000000
[ 6731.508706] R13: ffff9c97a08e0000 R14: ffff9c97a08e0a68 R15: 0000000000000000
[ 6731.508708] FS: 00007f2617cd2740(0000) GS:ffff9c987f4c0000(0000) knlGS:0000000000000000
[ 6731.508710] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 6731.508711] CR2: 0000000000000000 CR3: 0000001e765c4006 CR4: 00000000003606e0
[ 6731.508713] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 6731.508714] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 6731.508715] Call Trace:
[ 6731.508734] i40e_vsi_close+0x84/0x90 [i40e]
[ 6731.508742] i40e_quiesce_vsi.part.98+0x3c/0x40 [i40e]
[ 6731.508749] i40e_pf_quiesce_all_vsi+0x55/0x60 [i40e]
[ 6731.508757] i40e_prep_for_reset+0x59/0x130 [i40e]
[ 6731.508765] i40e_reconfig_rss_queues+0x5a/0x120 [i40e]
[ 6731.508774] i40e_set_channels+0xda/0x170 [i40e]
[ 6731.508778] ethtool_set_channels+0xe9/0x150
[ 6731.508781] dev_ethtool+0x1b94/0x2920
[ 6731.508805] dev_ioctl+0xc2/0x590
[ 6731.508811] sock_do_ioctl+0xae/0x150
[ 6731.508813] sock_ioctl+0x34f/0x3c0
[ 6731.508821] ksys_ioctl+0x98/0xb0
[ 6731.508828] __x64_sys_ioctl+0x1a/0x20
[ 6731.508831] do_syscall_64+0x57/0x1c0
[ 6731.508835] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 4b8164467b85 ("i40e: Add common function for finding VSI by type")
Signed-off-by: Grzegorz Szczurek <[email protected]>
Signed-off-by: Arkadiusz Kubalewski <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Trusted VF with unicast promiscuous mode set, could listen to TX
traffic of other VFs.
Set unicast promiscuous mode to RX traffic, if VSI has port VLAN
configured. Rename misleading I40E_AQC_SET_VSI_PROMISC_TX bit to
I40E_AQC_SET_VSI_PROMISC_RX_ONLY. Aligned unicast promiscuous with
VLAN to the one without VLAN.
Fixes: 6c41a7606967 ("i40e: Add promiscuous on VLAN support")
Fixes: 3b1200891b7f ("i40e: When in promisc mode apply promisc mode to Tx Traffic as well")
Signed-off-by: Przemyslaw Patynowski <[email protected]>
Signed-off-by: Aleksandr Loktionov <[email protected]>
Signed-off-by: Arkadiusz Kubalewski <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Right now, igc_ptp_reset() is called from igc_reset(), which is called
from igc_probe() before igc_ptp_init() has a chance to run. It is
detected as an attempt to use an spinlock without registering its key
first. See log below.
To avoid this problem, simplify the initialization: igc_ptp_init() is
only called from igc_probe(), and igc_ptp_reset() is only called from
igc_reset().
[ 2.736332] INFO: trying to register non-static key.
[ 2.736902] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input10
[ 2.737513] the code is fine but needs lockdep annotation.
[ 2.737513] turning off the locking correctness validator.
[ 2.737515] CPU: 8 PID: 239 Comm: systemd-udevd Tainted: G E 5.8.0-rc7+ #13
[ 2.737515] Hardware name: Gigabyte Technology Co., Ltd. Z390 AORUS ULTRA/Z390 AORUS ULTRA-CF, BIOS F7 03/14/2019
[ 2.737516] Call Trace:
[ 2.737521] dump_stack+0x78/0xa0
[ 2.737524] register_lock_class+0x6b1/0x6f0
[ 2.737526] ? lockdep_hardirqs_on_prepare+0xca/0x160
[ 2.739177] ? _raw_spin_unlock_irq+0x24/0x50
[ 2.739179] ? trace_hardirqs_on+0x1c/0xf0
[ 2.740820] __lock_acquire+0x56/0x1ff0
[ 2.740823] ? __schedule+0x30c/0x970
[ 2.740825] lock_acquire+0x97/0x3e0
[ 2.740830] ? igc_ptp_reset+0x35/0xf0 [igc]
[ 2.740833] ? schedule_hrtimeout_range_clock+0xb7/0x120
[ 2.742507] _raw_spin_lock_irqsave+0x3a/0x50
[ 2.742512] ? igc_ptp_reset+0x35/0xf0 [igc]
[ 2.742515] igc_ptp_reset+0x35/0xf0 [igc]
[ 2.742519] igc_reset+0x96/0xd0 [igc]
[ 2.744148] igc_probe+0x68f/0x7d0 [igc]
[ 2.745796] local_pci_probe+0x3d/0x70
[ 2.745799] pci_device_probe+0xd1/0x190
[ 2.745802] really_probe+0x15a/0x3f0
[ 2.759936] driver_probe_device+0xe1/0x150
[ 2.759937] device_driver_attach+0xa8/0xb0
[ 2.761786] __driver_attach+0x89/0x150
[ 2.761786] ? device_driver_attach+0xb0/0xb0
[ 2.761787] ? device_driver_attach+0xb0/0xb0
[ 2.761788] bus_for_each_dev+0x66/0x90
[ 2.765012] bus_add_driver+0x12e/0x1f0
[ 2.765716] driver_register+0x8b/0xe0
[ 2.766418] ? 0xffffffffc0230000
[ 2.767119] do_one_initcall+0x5a/0x310
[ 2.767826] ? kmem_cache_alloc_trace+0xe9/0x200
[ 2.768528] do_init_module+0x5c/0x260
[ 2.769206] __do_sys_finit_module+0x93/0xe0
[ 2.770048] do_syscall_64+0x46/0xa0
[ 2.770716] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 2.771396] RIP: 0033:0x7f83534589e0
[ 2.772073] Code: 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 2e 2e 2e 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 80 24 0d 00 f7 d8 64 89 01 48
[ 2.772074] RSP: 002b:00007ffd31d0ed18 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 2.774854] RAX: ffffffffffffffda RBX: 000055d52816aba0 RCX: 00007f83534589e0
[ 2.774855] RDX: 0000000000000000 RSI: 00007f83535b982f RDI: 0000000000000006
[ 2.774855] RBP: 00007ffd31d0ed60 R08: 0000000000000000 R09: 00007ffd31d0ed30
[ 2.774856] R10: 0000000000000006 R11: 0000000000000246 R12: 0000000000000000
[ 2.774856] R13: 0000000000020000 R14: 00007f83535b982f R15: 000055d527f5e120
Fixes: 5f2958052c58 ("igc: Add basic skeleton for PTP")
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Reviewed-by: Andre Guedes <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Fix pci_cfg_wait queue locking problem (Bjorn Helgaas)
- Convert PCIe capability PCIBIOS errors to errno (Bolarinwa Olayemi
Saheed)
- Align PCIe capability and PCI accessor return values (Bolarinwa
Olayemi Saheed)
- Fix pci_create_slot() reference count leak (Qiushi Wu)
- Announce device after early fixups (Tiezhu Yang)
PCI device hotplug:
- Make rpadlpar functions static (Wei Yongjun)
Driver binding:
- Add device even if driver attach failed (Rajat Jain)
Virtualization:
- xen: Remove redundant initialization of irq (Colin Ian King)
IOMMU:
- Add pci_pri_supported() to check device or associated PF (Ashok Raj)
- Release IVRS table in AMD ACS quirk (Hanjun Guo)
- Mark AMD Navi10 GPU rev 0x00 ATS as broken (Kai-Heng Feng)
- Treat "external-facing" devices themselves as internal (Rajat Jain)
MSI:
- Forward MSI-X error code in pci_alloc_irq_vectors_affinity() (Piotr
Stankiewicz)
Error handling:
- Clear PCIe Device Status errors only if OS owns AER (Jonathan
Cameron)
- Log correctable errors as warning, not error (Matt Jolly)
- Use 'pci_channel_state_t' instead of 'enum pci_channel_state' (Luc
Van Oostenryck)
Peer-to-peer DMA:
- Allow P2PDMA on AMD Zen and newer CPUs (Logan Gunthorpe)
ASPM:
- Add missing newline in sysfs 'policy' (Xiongfeng Wang)
Native PCIe controllers:
- Convert to devm_platform_ioremap_resource_byname() (Dejin Zheng)
- Convert to devm_platform_ioremap_resource() (Dejin Zheng)
- Remove duplicate error message from devm_pci_remap_cfg_resource()
callers (Dejin Zheng)
- Fix runtime PM imbalance on error (Dinghao Liu)
- Remove dev_err() when handing an error from platform_get_irq()
(Krzysztof Wilczyński)
- Use pci_host_bridge.windows list directly instead of splicing in a
temporary list for cadence, mvebu, host-common (Rob Herring)
- Use pci_host_probe() instead of open-coding all the pieces for
altera, brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3,
versatile, xgene, xilinx, xilinx-nwl (Rob Herring)
- Default host bridge parent device to the platform device (Rob
Herring)
- Use pci_is_root_bus() instead of tracking root bus number
separately in aardvark, designware (imx6, keystone,
designware-host), mobiveil, xilinx-nwl, xilinx, rockchip, rcar (Rob
Herring)
- Set host bridge bus number in pci_scan_root_bus_bridge() instead of
each driver for aardvark, designware-host, host-common, mediatek,
rcar, tegra, v3-semi (Rob Herring)
- Move DT resource setup into devm_pci_alloc_host_bridge() (Rob
Herring)
- Set bridge map_irq and swizzle_irq to default functions; drivers
that don't support legacy IRQs (iproc) need to undo this (Rob
Herring)
ARM Versatile PCIe controller driver:
- Drop flag PCI_ENABLE_PROC_DOMAINS (Rob Herring)
Cadence PCIe controller driver:
- Use "dma-ranges" instead of "cdns,no-bar-match-nbits" property
(Kishon Vijay Abraham I)
- Remove "mem" from reg binding (Kishon Vijay Abraham I)
- Fix cdns_pcie_{host|ep}_setup() error path (Kishon Vijay Abraham I)
- Convert all r/w accessors to perform only 32-bit accesses (Kishon
Vijay Abraham I)
- Add support to start link and verify link status (Kishon Vijay
Abraham I)
- Allow pci_host_bridge to have custom pci_ops (Kishon Vijay Abraham I)
- Add new *ops* for CPU addr fixup (Kishon Vijay Abraham I)
- Fix updating Vendor ID and Subsystem Vendor ID register (Kishon
Vijay Abraham I)
- Use bridge resources for outbound window setup (Rob Herring)
- Remove private bus number and range storage (Rob Herring)
Cadence PCIe endpoint driver:
- Add MSI-X support (Alan Douglas)
HiSilicon PCIe controller driver:
- Remove non-ECAM HiSilicon hip05/hip06 driver (Rob Herring)
Intel VMD host bridge driver:
- Use Shadow MEMBAR registers for QEMU/KVM guests (Jon Derrick)
Loongson PCIe controller driver:
- Use DECLARE_PCI_FIXUP_EARLY for bridge_class_quirk() (Tiezhu Yang)
Marvell Aardvark PCIe controller driver:
- Indicate error in 'val' when config read fails (Pali Rohár)
- Don't touch PCIe registers if no card connected (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Setup BAR0 in order to fix MSI (Shmuel Hazan)
Microsoft Hyper-V host bridge driver:
- Fix a timing issue which causes kdump to fail occasionally (Wei Hu)
- Make some functions static (Wei Yongjun)
NVIDIA Tegra PCIe controller driver:
- Revert tegra124 raw_violation_fixup (Nicolas Chauvet)
- Remove PLL power supplies (Thierry Reding)
Qualcomm PCIe controller driver:
- Change duplicate PCI reset to phy reset (Abhishek Sahu)
- Add missing ipq806x clocks in PCIe driver (Ansuel Smith)
- Add missing reset for ipq806x (Ansuel Smith)
- Add ext reset (Ansuel Smith)
- Use bulk clk API and assert on error (Ansuel Smith)
- Add support for tx term offset for rev 2.1.0 (Ansuel Smith)
- Define some PARF params needed for ipq8064 SoC (Ansuel Smith)
- Add ipq8064 rev2 variant (Ansuel Smith)
- Support PCI speed set for ipq806x (Sham Muthayyan)
Renesas R-Car PCIe controller driver:
- Use devm_pci_alloc_host_bridge() (Rob Herring)
- Use struct pci_host_bridge.windows list directly (Rob Herring)
- Convert rcar-gen2 to use modern host bridge probe functions (Rob
Herring)
TI J721E PCIe driver:
- Add TI J721E PCIe host and endpoint driver (Kishon Vijay Abraham I)
Xilinx Versal CPM PCIe controller driver:
- Add Versal CPM Root Port driver and YAML schema (Bharat Kumar
Gogada)
MicroSemi Switchtec management driver:
- Add missing __iomem and __user tags to fix sparse warnings (Logan
Gunthorpe)
Miscellaneous:
- Replace http:// links with https:// (Alexander A. Klimov)
- Replace lkml.org, spinics, gmane with lore.kernel.org (Bjorn
Helgaas)
- Remove unused pci_lost_interrupt() (Heiner Kallweit)
- Move PCI_VENDOR_ID_REDHAT definition to pci_ids.h (Huacai Chen)
- Fix kerneldoc warnings (Krzysztof Kozlowski)"
* tag 'pci-v5.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (113 commits)
PCI: Fix kerneldoc warnings
PCI: xilinx-cpm: Add Versal CPM Root Port driver
PCI: xilinx-cpm: Add YAML schemas for Versal CPM Root Port
PCI: Set bridge map_irq and swizzle_irq to default functions
PCI: Move DT resource setup into devm_pci_alloc_host_bridge()
PCI: rcar-gen2: Convert to use modern host bridge probe functions
PCI: Remove dev_err() when handing an error from platform_get_irq()
MAINTAINERS: Add Kishon Vijay Abraham I for TI J721E SoC PCIe
misc: pci_endpoint_test: Add J721E in pci_device_id table
PCI: j721e: Add TI J721E PCIe driver
PCI: switchtec: Add missing __iomem tag to fix sparse warnings
PCI: switchtec: Add missing __iomem and __user tags to fix sparse warnings
PCI: rpadlpar: Make functions static
PCI/P2PDMA: Allow P2PDMA on AMD Zen and newer CPUs
PCI: Release IVRS table in AMD ACS quirk
PCI: Announce device after early fixups
PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken
PCI: Remove unused pci_lost_interrupt()
dt-bindings: PCI: Add EP mode dt-bindings for TI's J721E SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J721E SoC
...
|
|
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[[email protected]: fs/crypto/inline_crypt.c needs linux/slab.h]
[[email protected]: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <[email protected]>
Signed-off-by: Waiman Long <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Acked-by: David Howells <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Acked-by: Johannes Weiner <[email protected]>
Cc: Jarkko Sakkinen <[email protected]>
Cc: James Morris <[email protected]>
Cc: "Serge E. Hallyn" <[email protected]>
Cc: Joe Perches <[email protected]>
Cc: Matthew Wilcox <[email protected]>
Cc: David Rientjes <[email protected]>
Cc: Dan Carpenter <[email protected]>
Cc: "Jason A . Donenfeld" <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2020-08-01
This series contains updates to the ice driver only.
Wei Yongjun marks power management functions with __maybe_unused.
Nick disables VLAN pruning in promiscuous mode and renames grst_delay to
grst_timeout.
Kiran modifies the check for linearization and corrects the vsi_id mask
value.
Vignesh replaces the use of flow profile locks to RSS profile locks for RSS
rule removal. Destroys flow profile lock on clearing XLT table and
clears extraction sequence entries.
Jesse adds some statistics and removes an unreported one.
Brett allows for 2 queue configuration for VFs.
Surabhi adds a check for failed allocation of an extraction sequence
table.
Tony updates the PTYPE lookup table and makes other trivial fixes.
Victor extends profile ID locks to be held until all references are
completed.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Resolved kernel/bpf/btf.c using instructions from merge commit
69138b34a7248d2396ab85c8652e20c0c39beaba
Signed-off-by: David S. Miller <[email protected]>
|
|
This is a collection of minor fixes including typos, white space, and
style. No functional changes.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
|
|
The profile ID map lock should be held till the caller completes
all references of that profile entries.
The current code releases the lock right after the match search.
This caused a driver issue when the profile map entries were
referenced after it was freed in other thread after the lock was
released earlier.
Signed-off-by: Victor Raj <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Update the PTYPE lookup table to reflect values that can be set by the
hardware.
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
|
|
Disable VLAN pruning when entering promiscuous mode, and re-enable it
when exiting.
Without this VLAN-over-bridge topologies created on the device won't be
functional unless rx-vlan-filter is explicitly disabled with ethtool.
Signed-off-by: Nick Nunley <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In the ice_init_hw_tbls, if the devm_kcalloc for es->written fails, catch
that error and bail out gracefully, instead of continuing with a NULL
pointer.
Fixes: 32d63fa1e9f3 ("ice: Initialize DDP package structures")
Signed-off-by: Surabhi Boob <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
This is a port of commit 248de22e638f ("i40e/i40evf: Account for frags
split over multiple descriptors in check linearize")
As part of testing workloads (read/write) using larger IO size (128K)
tx_timeout is observed and whenever it happens, it was due to
tx_linearize.
Signed-off-by: Kiran Patil <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Currently VFs are only allowed to get 16, 4, and 1 queue pair by
default, which require 17, 5, and 2 MSI-X vectors respectively. This
is because each VF needs a MSI-X per data queue and a MSI-X for its
other interrupt. The calculation is based on the number of VFs created,
MSI-X available, and queue pairs available at the time of VF creation.
Unfortunately the values above exclude 2 queue pairs when only 3 MSI-X
are available to each VF based on resource constraints. The current
calculation would default to 2 MSI-X and 1 queue pair. This is a waste
of resources, so fix this by allowing 2 queue pairs per VF when there
are between 2 and 5 MSI-X available per VF.
Signed-off-by: Brett Creeley <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
This fix has been added to address memory leak issues resulting from
triggering a sudden driver reset which does not allow us to follow our
normal removal flows for SW XLT entries for advanced features.
- Adding call to destroy flow profile locks when clearing SW XLT tables.
- Extraction sequence entries were not correctly cleared previously
which could cause ownership conflicts for repeated reset-replay calls.
Fixes: 31ad4e4ee1e4 ("ice: Allocate flow profile")
Signed-off-by: Vignesh Sridhar <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Display and count some useful hot-path statistics. The usefulness is as
follows:
- tx_restart: use to determine if the transmit ring size is too small or
if the transmit interrupt rate is too low.
- rx_gro_dropped: use to count drops from GRO layer, which previously were
completely uncounted when occurring.
- tx_busy: use to determine when the driver is miscounting number of
descriptors needed for an skb.
- tx_timeout: as our other drivers, count the number of times we've reset
due to timeout because the kernel only prints a warning once per netdev.
Several of these were already counted but not displayed.
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The page reuse statistic wasn't even being displayed to the user, even
though the driver counted it. Don't waste the struct space and hot-path
cycles since the driver doesn't display it.
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Replacing flow profile locks with RSS profile locks in the function to
remove all RSS rules for a given VSI. This is to align the locks used
for RSS rule addition to VSI and removal during VSI teardown to avoid
a race condition owing to several iterations of the above operations.
In function to get RSS rules for given VSI and protocol header replacing
the pointer reference of the RSS entry with a copy of hash value to
ensure thread safety.
Signed-off-by: Vignesh Sridhar <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
set_rss_lut can fail due to incorrect vsi_id mask. vsi_id is 10 bit
but mask was 0x1FF whereas it should be 0x3FF.
For vsi_num >= 512, FW set_rss_lut can fail with return code
EACCESS (VSI ownership issue) because software was providing
incorrect vsi_num (dropping 10th bit due to incorrect mask) for
set_rss_lut admin command
Signed-off-by: Kiran Patil <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The grst_delay variable in ice_check_reset contains the maximum time
(in 100 msec units) that the driver will wait for a reset event to
transition to the Device Active state. The value is the sum of three
separate components:
1) The maximum time it may take for the firmware to process its
outstanding command before handling the reset request.
2) The value in RSTCTL.GRSTDEL (the delay firmware inserts between first
seeing the driver reset request and the actual hardware assertion).
3) The maximum expected reset processing time in hardware.
Referring to this total time as "grst_delay" is misleading and
potentially confusing to someone checking the code and cross-referencing
the hardware specification.
Fix this by renaming the variable to "grst_timeout", which is more
descriptive of its actual use.
Signed-off-by: Nick Nunley <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In certain configurations without power management support, the
following warnings happen:
drivers/net/ethernet/intel/ice/ice_main.c:4214:12: warning:
'ice_resume' defined but not used [-Wunused-function]
4214 | static int ice_resume(struct device *dev)
| ^~~~~~~~~~
drivers/net/ethernet/intel/ice/ice_main.c:4150:12: warning:
'ice_suspend' defined but not used [-Wunused-function]
4150 | static int ice_suspend(struct device *dev)
| ^~~~~~~~~~~
Mark these functions as __maybe_unused to make it clear to the
compiler that this is going to happen based on the configuration,
which is the standard for these types of functions.
Fixes: 769c500dcc1e ("ice: Add advanced power mgmt for WoL")
Reported-by: Hulk Robot <[email protected]>
Signed-off-by: Wei Yongjun <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Use eth_zero_addr() to clear mac address instead of memset().
Signed-off-by: Miaohe Lin <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Use eth_zero_addr() to clear mac address instead of memset().
Signed-off-by: Miaohe Lin <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Replace memsets of 1 byte with simple assignment.
Issue found with checkpatch.pl
Signed-off-by: Suraj Upadhyay <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Replace memsets of 1 byte with simple assignment.
Issue found with checkpatch.pl
Signed-off-by: Suraj Upadhyay <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|