| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Trusted VF can use up every resource available, leaving nothing
to other trusted VFs.
Introduce define, which calculates MacVlan resources available based
on maximum available MacVlan resources, bare minimum for each VF and
number of currently allocated VFs.
Signed-off-by: Przemyslaw Patynowski <[email protected]>
Signed-off-by: Karen Sornek <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
kfree() and bitmap_free() are the same. But using the latter is more
consistent when freeing memory allocated with bitmap_zalloc().
Signed-off-by: Christophe JAILLET <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When a bitmap is local to a function, it is safe to use the non-atomic
__[set|clear]_bit(). No concurrent accesses can occur.
Signed-off-by: Christophe JAILLET <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The 'possible_idx' bitmap is set just after it is zeroed, so we can save
the first step.
The 'free_idx' bitmap is used only at the end of the function as the
result of a bitmap xor operation. So there is no need to explicitly
zero it before.
So, slightly simply the code and remove 2 useless 'bitmap_zero()' call
Signed-off-by: Christophe JAILLET <[email protected]>
Tested-by: Sandeep Penigalapati <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In current switchdev implementation, every VF PR is assigned to
individual ring on switchdev ctrl VSI. For slow-path traffic, there
is a mapping VF->ring done in software based on src_vsi value (by
calling ice_eswitch_get_target_netdev function).
With this change, HW solution is introduced which is more
efficient. For each VF, src MAC (VF's MAC) filter will be created,
which forwards packets to the corresponding switchdev ctrl VSI queue
based on src MAC address.
This filter has to be removed and then replayed in case of
resetting one VF. Keep information about this rule in repr->mac_rule,
thanks to that we know which rule has to be removed and replayed
for a given VF.
In case of CORE/GLOBAL all rules are removed
automatically. We have to take care of readding them. This is done
by ice_replay_vsi_adv_rule.
When driver leaves switchdev mode, remove all advanced rules
from switchdev ctrl VSI. This is done by ice_rem_adv_rule_for_vsi.
Flag repr->rule_added is needed because in some cases reset
might be triggered before VF sends request to add MAC.
Co-developed-by: Grzegorz Nitka <[email protected]>
Signed-off-by: Grzegorz Nitka <[email protected]>
Signed-off-by: Wojciech Drewek <[email protected]>
Tested-by: Sandeep Penigalapati <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
ice_replay_vsi_adv_rule will replay advanced rules for a given VSI.
Exit this function when list of rules for given recipe is empty.
Do not add rule when given vsi_handle does not match vsi_handle
from the rule info.
Use ICE_MAX_NUM_RECIPES instead of ICE_SW_LKUP_LAST in order to find
advanced rules as well.
Signed-off-by: Victor Raj <[email protected]>
Signed-off-by: Wojciech Drewek <[email protected]>
Tested-by: Sandeep Penigalapati <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In the absence of this validation, if the user requests to
configure queues more than the enabled queues, it results in
sending the requested number of queues to the kernel stack
(due to the asynchronous nature of VF response), in which
case the stack might pick a queue to transmit that is not
enabled and result in Tx hang. Fix this bug by
limiting the total number of queues allocated for VF to
active queues of VF.
Fixes: d5b33d024496 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Ashwin Vijayavel <[email protected]>
Signed-off-by: Karen Sornek <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There was a wrong queues representation in sysfs during
driver's reinitialization in case of online cpus number is
less than combined queues. It was caused by stopped
NetworkManager, which is responsible for calling vsi_open
function during driver's initialization.
In specific situation (ex. 12 cpus online) there were 16 queues
in /sys/class/net/<iface>/queues. In case of modifying queues with
value higher, than number of online cpus, then it caused write
errors and other errors.
Add updating of sysfs's queues representation during driver
initialization.
Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Lukasz Cieplicki <[email protected]>
Signed-off-by: Jedrzej Jagielski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When loading the i40e driver, it prints a message like: 'The driver for the
device detected a newer version of the NVM image v1.x than expected v1.y.
Please install the most recent version of the network driver.' This is
misleading as the driver is working as expected.
Fix that by removing the second part of message and changing it from
dev_info to dev_dbg.
Fixes: 4fb29bddb57f ("i40e: The driver now prints the API version in error message")
Signed-off-by: Mateusz Palczewski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Using ifconfig command to delete the ipv6 address will cause
the i40e network card driver to delete its internal mac_filter and
i40e_service_task kernel thread will concurrently access the mac_filter.
These two processes are not protected by lock
so causing the following use-after-free problems.
print_address_description+0x70/0x360
? vprintk_func+0x5e/0xf0
kasan_report+0x1b2/0x330
i40e_sync_vsi_filters+0x4f0/0x1850 [i40e]
i40e_sync_filters_subtask+0xe3/0x130 [i40e]
i40e_service_task+0x195/0x24c0 [i40e]
process_one_work+0x3f5/0x7d0
worker_thread+0x61/0x6c0
? process_one_work+0x7d0/0x7d0
kthread+0x1c3/0x1f0
? kthread_park+0xc0/0xc0
ret_from_fork+0x35/0x40
Allocated by task 2279810:
kasan_kmalloc+0xa0/0xd0
kmem_cache_alloc_trace+0xf3/0x1e0
i40e_add_filter+0x127/0x2b0 [i40e]
i40e_add_mac_filter+0x156/0x190 [i40e]
i40e_addr_sync+0x2d/0x40 [i40e]
__hw_addr_sync_dev+0x154/0x210
i40e_set_rx_mode+0x6d/0xf0 [i40e]
__dev_set_rx_mode+0xfb/0x1f0
__dev_mc_add+0x6c/0x90
igmp6_group_added+0x214/0x230
__ipv6_dev_mc_inc+0x338/0x4f0
addrconf_join_solict.part.7+0xa2/0xd0
addrconf_dad_work+0x500/0x980
process_one_work+0x3f5/0x7d0
worker_thread+0x61/0x6c0
kthread+0x1c3/0x1f0
ret_from_fork+0x35/0x40
Freed by task 2547073:
__kasan_slab_free+0x130/0x180
kfree+0x90/0x1b0
__i40e_del_filter+0xa3/0xf0 [i40e]
i40e_del_mac_filter+0xf3/0x130 [i40e]
i40e_addr_unsync+0x85/0xa0 [i40e]
__hw_addr_sync_dev+0x9d/0x210
i40e_set_rx_mode+0x6d/0xf0 [i40e]
__dev_set_rx_mode+0xfb/0x1f0
__dev_mc_del+0x69/0x80
igmp6_group_dropped+0x279/0x510
__ipv6_dev_mc_dec+0x174/0x220
addrconf_leave_solict.part.8+0xa2/0xd0
__ipv6_ifa_notify+0x4cd/0x570
ipv6_ifa_notify+0x58/0x80
ipv6_del_addr+0x259/0x4a0
inet6_addr_del+0x188/0x260
addrconf_del_ifaddr+0xcc/0x130
inet6_ioctl+0x152/0x190
sock_do_ioctl+0xd8/0x2b0
sock_ioctl+0x2e5/0x4c0
do_vfs_ioctl+0x14e/0xa80
ksys_ioctl+0x7c/0xa0
__x64_sys_ioctl+0x42/0x50
do_syscall_64+0x98/0x2c0
entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Di Zhu <[email protected]>
Signed-off-by: Rui Zhang <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Hide i40e opcode information sent during response to VF in case when
untrusted VF tried to change MAC on the VF interface.
This is implemented by adding an additional parameter 'hide' to the
response sent to VF function that hides the display of error
information, but forwards the error code to VF.
Previously it was not possible to send response with some error code
to VF without displaying opcode information.
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <[email protected]>
Signed-off-by: Mateusz Palczewski <[email protected]>
Reviewed-by: Paul M Stillwell Jr <[email protected]>
Reviewed-by: Aleksandr Loktionov <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Recent bpf-next merge brought in header changes which uncovered
includes missing in net-next which were not present in bpf-next.
Build problems happen only on less-popular arches like hppa,
sparc, alpha etc.
I could repro the build problem with ice but not the mlx5 problem
Abdul was reporting. mlx5 does look like it should include filter.h,
anyway.
Reported-by: Abdul Haleem <[email protected]>
Fixes: e63a02348958 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next")
Link: https://lore.kernel.org/all/[email protected]/
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764c7 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f36 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0fb ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/[email protected]/
net/smc/smc_wr.c
commit 49dc9013e34b ("net/smc: Use the bitmap API when applicable")
commit 349d43127dac ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add support to enable flow-director filter when multiple TCs are
configured. Flow director filter can be configured using ethtool
(--config-ntuple option). When multiple TCs are configured, each
TC is mapped to an unique HW VSI. So VSI corresponding to queue
used in filter is identified and flow director context is updated
with correct VSI while configuring ntuple filter in HW.
Signed-off-by: Kiran Patil <[email protected]>
Signed-off-by: Amritha Nambiar <[email protected]>
Signed-off-by: Sudheer Mogilappagari <[email protected]>
Tested-by: Bharathi Sreenivas <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Support for the PTP pin function on 82580/i354/i350 based adapters.
Because the time registers of these adapters do not have the nice split in
second rollovers as the i210 has, the implementation is slightly more
complex compared to the i210 implementation.
Signed-off-by: Ruud Bos <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Support for the PEROUT PTP pin function on 82580/i354/i350 based adapters.
Because the time registers of these adapters do not have the nice split in
second rollovers as the i210 has, the implementation is slightly more
complex compared to the i210 implementation.
Signed-off-by: Ruud Bos <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Remove code duplication in the tsync interrupt handler function by moving
this logic to separate functions. This keeps the interrupt handler readable
and allows the new functions to be extended for adapter types other than
i210.
Signed-off-by: Ruud Bos <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Allow reuse of SDP config struct initialization by moving it to a
separate function.
Signed-off-by: Ruud Bos <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Acked-by: Marc Kleine-Budde <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Acked-by: Nikolay Aleksandrov <[email protected]>
Acked-by: Stefano Garzarella <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Time synchronization was not properly enabled on non-MSI-X platforms.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Signed-off-by: James McLaughlin <[email protected]>
Reviewed-by: Vinicius Costa Gomes <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
It was reported that when PCIe PTM is enabled, some lockups could
be observed with some integrated i225-V models.
While the issue is investigated, we can disable crosstimestamp for
those models and see no loss of functionality, because those models
don't have any support for time synchronization.
Fixes: a90ec8483732 ("igc: Add support for PTP getcrosststamp()")
Link: https://lore.kernel.org/all/[email protected]/
Reported-by: Stefan Dietrich <[email protected]>
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
ixgbevf driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
ixgbe driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
igc driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
igb driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
ice driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
iavf driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
i40e driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx element.
e1000 driver runs Tx completion polling cycle right before the Rx
one. Now that e1000 uses napi_consume_skb() to put skbuff_heads of
completed entries into the cache, it will never empty and always
warm at that moment. Switch to the napi_build_skb() to relax mm
pressure on heavy Rx and increase throughput.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In order to take the best from per-cpu NAPI skbuff_head caches and
CPU cycles, let's switch from dev_kfree_skb_any(), which passes skb
back to the mm layer, to napi_consume_skb(), which feeds those
caches on non-zero budget instead (falls back to the former on 0).
Do the replacement in e1000_unmap_and_free_tx_resource(). There are
4 call sites of this function throughout the driver:
* e1000_clean_tx_ring(). Slowpath, process context, cleans the
whole Tx ring on ifdown. Use budget of 0 here;
* e1000_tx_map(). Hotpath, net Tx softirq, unmaps the buffers in
case of error. Use 0 as well;
* e1000_clean_tx_irq(). Hotpath, NAPI Tx completion polling cycle.
As the driver doesn't count completed Tx entries towards the NAPI
budget, just use the poll budget of 64 to utilize caches.
Apart from being a preparation for switching to napi_build_skb(),
this is useful on its own as well, as napi_consume_skb() flushes
skb caches by batches of 32 instead of one-at-a-time.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
include/net/sock.h
commit 8f905c0e7354 ("inet: fully convert sk->sk_rx_dst to RCU rules")
commit 43f51df41729 ("net: move early demux fields close to sk_refcnt")
https://lore.kernel.org/all/[email protected]/
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Fix an odd indent where some code was left indented, and causes smatch
to warn:
ice_log_pkg_init() warn: inconsistent indenting
While here, for consistency, add a break after the default case.
This commit has a Fixes: but we caught this while it was only in net-next.
Fixes: 247dd97d713c ("ice: Refactor status flow for DDP load")
Signed-off-by: Jesse Brandeburg <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-12-21
This series contains updates to ice driver only.
Karol modifies the reset flow to correct issues with PTP reset.
Jake extends PTP support for E822 based devices. This includes a few
cleanup patches, that fix some minor issues. In addition, there are some
slight refactors to ease the addition of E822 support, followed by adding
the new hardware implementation ice_ptp_hw.c.
There are a few major differences with E822 support compared to E810
support:
*) The E822 device has a Clock Generation Unit which must be initialized in
order to generate proper clock frequencies on the output that drives the PTP
hardware clock registers
*) The E822 PHY is a bit different and requires a more complex
initialization procedure which must be rerun any time the link configuration
changes.
*) The E822 devices support enhanced timestamp calibration by making use of
a process called Vernier offset measurement. This allows the hardware to
measure phase offset related to the PHY clocks for Serdes and FEC, reducing
the inaccuracy of the timestamp relative to the actual packet transmission
and receipt. Making use of this requires data gathered from the first
transmitted and received packets, and waiting for the PHY to complete the
calibration measurements. This is done as part of a new kthread, ov_work.
Note that to avoid delay in enabling timestamps, we start the PHY in
'bypass' mode which allows timestamps to be captured without the Vernier
calibration measurement. Once the first packets have been sent and received,
we then complete the calibration setup and exit bypass mode and begin using
the more precise timestamps. According to the datasheet, timestamps without
calibration data can be incorrect relative to actual receipt or transmission
by up to 1 clock cycle (~1.25 nanoseconds), while calibrated timestamps
should be correct to within 1/8th of a clock cycle (~0.15 nanoseconds).
*) E822 devices support crosstimestamping via PCIe PTM, which we enable when
available on the platform.
There is a fair amount of logic required to perform PHY and CGU
initialization, which is the vast majority of the new code, but it is fairly
self contained within ice_ptp_hw.c, with the exception of monitoring for
offset validity being handled by a kthread.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: support crosstimestamping on E822 devices if supported
ice: exit bypass mode once hardware finishes timestamp calibration
ice: ensure the hardware Clock Generation Unit is configured
ice: implement basic E822 PTP support
ice: convert clk_freq capability into time_ref
ice: introduce ice_ptp_init_phc function
ice: use 'int err' instead of 'int status' in ice_ptp_hw.c
ice: PTP: move setting of tstamp_config
ice: introduce ice_base_incval function
ice: Fix E810 PTP reset flow
====================
Link: https://lore.kernel.org/r/[email protected]
Acked-by: Richard Cochran <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Delete the redundant word 'by'.
Signed-off-by: Xiang wangx <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Refactoring "PF still resetting" message, because previous version looked
like a bug - it informed about changes that worked as designed but might
confuse users. Changes requested to make message more user-friendly.
Signed-off-by: Karen Sornek <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The variable used for return status in `igb_write_xmdio_reg' function
is never changed and this function is just need return 0. Thus, the
`ret_val' can be removed and return 0 at the end of the
`igb_write_xmdio_reg' function.
Signed-off-by: Jason Wang <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
'MII_CR_FULL_DUPLEX' define not in use. This patch comes to tidy up
obsolete define.
Signed-off-by: Sasha Neftin <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
'IGC_CTRL_EXT_LINK_MODE_MASK' not in use. This patch comes to tidy up
obsolete define.
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
i225 devices use only spi nvm type. This patch comes to tidy up
obsolete nvm types.
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
_phy_none type not in use. Clean up the code accordingly,
and get rid of the unused enum line
Signed-off-by: Sasha Neftin <[email protected]>
Reviewed-by: Paul Menzel <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
_I_PHY_ID not in use. Clean up the code accordingly,
and get rid of the unused define
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
E822 devices on supported platforms can generate a cross timestamp
between the platform ART and the device time. This process allows for
very precise measurement of the difference between the PTP hardware
clock and the platform time.
This is only supported if we know the TSC frequency relative to ART, so
we do not enable this unless the boot CPU has a known TSC frequency (as
required by convert_art_ns_to_tsc).
Because PCIe PTM support is not available on all platforms, introduce
CONFIG_ICE_HWTS and make it depend on X86 where we know the support
exists.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Once the E822 device has sent and received one packet, the hardware
computes the internal delay of the PHY using a process known as Vernier
calibration. This calibration calculates a more accurate offset for the
Tx and Rx timestamps. To make use of this offset, we need to exit the
bypass mode. This cannot be done until the PHY has completed offset
calibration, as indicated by the offset valid bits.
To handle this, introduce a kthread work item which will poll the offset
valid bits every few milliseconds seeing if it is safe to exit bypass
mode.
Once we have finished calibrating the offsets, we can program the total
Tx and Rx offset registers and turn off the bypass bit. This allows the
hardware to include the more precise vernier calibration offset, and
improves the timestamp precision.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The E822 device has a Clock Generation Unit (CGU) responsible for
determining the clock frequency that drives the timers.
Ensure this function is initialized when bringing up the PTP support, so
that the clock has a known frequency.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Implement support for the basic operations needed to enable the PTP
hardware clock on E822 devices.
This includes implementations for the various PHY access functions, as
well as the ability to start and stop the PHY timers. This is different
from the E810 device because the configuration depends on link speed, so
we cannot just start the PHYs immediately. We must wait until the link
is up to get proper values for the speed based initialization.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Convert the clk_freq value into the associated time_ref frequency value
for E822 devices. This simplifies determining the time reference value
for the clock.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When we enable support for E822 devices, there are some additional
steps required to initialize the PTP hardware clock. To make this easier
to implement as device-specific behavior, refactor the register setups
in ice_ptp_init_owner to a new ice_ptp_init_phc function defined in
ice_ptp_hw.c
This function will have a common section, and an e810 specific
sub-implementation.
This will enable easily extending the functionality to cover the E822
specific setup required to initialize the hardware clock generation
unit. It also makes it clear which steps are E810 specific vs which ones
are necessary for all ice devices.
Signed-off-by: Jacob Keller <[email protected]>
Reviewed-by: Paul Menzel <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice_ptp_hw.c file introduced a bunch of uses of "int status" instead
of the more traditional "int err" or "int ret". These are actually
traditional Linux error codes (as opposed to the recently removed
ice_status enumeration values).
We're about to add a bunch of new functions to ice_ptp_hw.c. It's
normally preferred in the ice driver to use "int ret" or "int err" when
dealing with error code values.
Instead of making the new functions use "int status" lets just fix all
of ice_ptp_hw.c to use "int err". This will match the new functions and
ensures a consistent style across at least the PTP related files.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|