| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Distribute the Tx queues evenly across all queue groups. This will
help the queues to get more equal sharing among the queues when all
are in use.
In the previous algorithm, the next queue group node will be picked up
only after the previous one filled with max children.
For example: if VSI is configured with 9 queues, the first 8 queues
will be assigned to queue group 1 and the 9th queue will be assigned to
queue group 2.
The 2 queue groups split the bandwidth between them equally (50:50).
The first queue group node will share the 50% bandwidth with all of
its children (8 queues). And the second queue group node will share
the entire 50% bandwidth with its only children.
The new algorithm will fix this issue.
Signed-off-by: Victor Raj <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
By default the queues are configured in legacy mode. The default
BW settings for legacy/advanced modes are different. The existing
code was using the advanced mode default value of 1 which was
incorrect. This caused the unbalanced BW sharing among siblings.
The recommended default value is applied.
Signed-off-by: Tarun Singh <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Mask bits before accessing the profile type field.
Signed-off-by: Tarun Singh <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
If a user sets the value of the TX or RX descriptors to some non-default
value using 'ethtool -G' then we need to not overwrite the values when
we rebuild the VSI. The VSI rebuild could happen as a result of a user
setting the number of queues via the 'ethtool -L' command. Fix this by
checking to see if the value we have stored is non-zero and if it is
then don't change the value.
Signed-off-by: Paul M Stillwell Jr <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Return ICE_ERR_DOES_NOT_EXIST return code if admin command error code is
ICE_AQ_RC_ENOENT (not exist). ice_aq_sw_rules is used when switch
rule is getting added/deleted/updated. In case of delete/update
switch rule, admin command can return ICE_AQ_RC_ENOENT error code
if such rule does not exist, hence return ICE_ERR_DOES_NOT_EXIST error
code from ice_aq_sw_rule, so that caller of this function can decide
how to handle ICE_ERR_DOES_NOT_EXIST.
Signed-off-by: Kiran Patil <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability
register will be cleared. This can lead to issues when a VF is
assigned to a VM because in these cases the VF driver receives no
indication of the PF PCI error/reset and additionally it is incapable
of restoring the cleared flag in the hypervisor configuration space
without fully reinitializing the driver interrupt functionality.
Since the VF driver is unable to easily resolve this condition on its own,
restore the VF MSI-X flag during the PF PCI reset handling.
Signed-off-by: Nick Nunley <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When the driver experiences a link event (especially link up)
there can be multiple events generated. Some of these are
link fault and still have a state of DOWN set. The problem
happens when the link comes UP during the PF driver handling
one of the LINK DOWN events. The status of the link is updated
and is now seen as UP, so when the actual LINK UP event comes,
the port information has already been updated to be seen as UP,
even though none of the UP activities have been completed.
After the link information has been updated in the link
handler and evaluated for MEDIA PRESENT, if the state
of the link has been changed to UP, treat the DOWN event
as an UP event since the link is now UP.
Signed-off-by: Dave Ertman <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
After a GLOBR, the link was broken so that a link
up situation was being seen as a link down.
The problem was that the rebuild process was updating
the port_info link status without doing any of the
other things that need to be done when link changes.
This was causing the port_info struct to have current
"UP" information so that any further UP interrupts
were skipped as redundant.
The rebuild flow should *not* be updating the port_info
struct link information, so eliminate this and leave
it to the link event handling code.
Signed-off-by: Dave Ertman <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There is a bug where the LFC settings are not being preserved
through a link event. The registers in question are the ones
that are touched (and restored) when a set_local_mib AQ command
is performed.
On a link-up event, make sure that a set_local_mib is being
performed.
Move the function ice_aq_set_lldp_mib() from the DCB specific
ice_dcb.c to ice_common.c so that the driver always has access
to this AQ command.
Signed-off-by: Dave Ertman <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Use the newly added pldmfw library to implement device flash update for
the Intel ice networking device driver. This support uses the devlink
flash update interface.
The main parts of the flash include the Option ROM, the netlist module,
and the main NVM data. The PLDM firmware file contains modules for each
of these components.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset (which would usually occur during
the next reboot).
Although the firmware AdminQ interface does report an immediate status
for each command, the NVM erase and NVM write commands receive status
asynchronously. The driver must not continue writing until previous
erase and write commands have finished. The real status of the NVM
commands is returned over the receive AdminQ. Implement a simple
interface that uses a wait queue so that the main update thread can
sleep until the completion status is reported by firmware. For erasing
the inactive banks, this can take quite a while in practice.
To help visualize the process to the devlink application and other
applications based on the devlink netlink interface, status is reported
via the devlink_flash_update_status_notify. While we do report status
after each 4k block when writing, there is no real status we can report
during erasing. We simply must wait for the complete module erasure to
finish.
With this implementation, basic flash update for the ice hardware is
supported.
Signed-off-by: Jacob Keller <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
After a flash update, the pending status of the update can be determined
from the device capabilities.
Read the appropriate device capability and store whether there is
a pending update awaiting a reboot.
Signed-off-by: Jacob Keller <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add structures, identifiers, and helper functions for several AdminQ
commands related to performing a firmware update for the ice hardware.
These will be used in future code for implementing the devlink
.flash_update handler.
Signed-off-by: Cudzilo, Szymon T <[email protected]>
Signed-off-by: Jacob Keller <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Extends function parsing response from Discover Device
Capability AQC to check if the device supports unified NVM update flow.
Signed-off-by: Jacek Naczyk <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
drivers/net/ethernet/intel/igc/igc_mac.c:424 igc_check_for_copper_link()
error: uninitialized symbol 'link'.
This patch come to fix this warning and initialize the 'link' symbol.
Reported-by: Dan Carpenter <[email protected]>
Fixes: 707abf069548 ("igc: Add initial LTR support")
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Remove ictxptc, ictxatc, cbtmpc, cbrdpc, cbrmpc and htcbdpc fields from
the hw_stats structure. Accordance to the i225 device
specification these fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
collision_delta, tx_packet_delta, txcw, adaptive_ifs and
has_fwsm fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
LED control currently not implemented.
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
IGC_ICTXPTC and IGC_ICTXATC are already defined elsewhere, remove this
double definition. Also, remove unneeded registers as they are not
applicable to i225 devices.
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Tx Queue Min Threshold Count register no applicable for the i225 device.
This patch comes to clean up it.
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The statistics of this register are being tracked, however, the register
was inadvertently missed when implementing igc_clear_hw_cntrs_base().
The register is clear on read, so add it to the function so that the
register is cleared when requested so the tracked count is accurate.
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Though we are populating and tracking ictxqec, the value is not being used
for anything so remove it altogether and save the register read.
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Aaron Brown <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
There isn't a case for 1G SGMII in ice_get_media_type() so add
the handling for it.
Also handle the special case where some direct attach
cables may report that they support 1G SGMII, but
that is erroneous since SGMII is supposed to be a
backplane media type (between a MAC and a PHY). If
the driver doesn't handle this special case then a
user could see the 'Port' in ethtool change from
'Direct attach Copper' to 'Backplane' when they have
forced the speed to 1G, but the cable hasn't changed.
Lastly, change ice_aq_get_phy_caps() to save the
module_type info if the function was called with
ICE_AQC_REPORT_TOPO_CAP. This call uses the media
information to populate the module_type. If no
media is present then the values in module_type
will be 0.
Signed-off-by: Paul M Stillwell Jr <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Report AOC types as fiber instead of unknown.
Signed-off-by: Doug Dziggel <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add AQC get link topology handle support. This is needed to determine
Direct Attach (DA) or backplane media type for PHY types that support
either. Get link topology handle cage node type request can be used to
determine if a cage is present or not. If a cage is present for PHY
types that supports both DA and backplane media type, then the media
type is DA, else the media type is backplane.
Signed-off-by: Paul Greenwalt <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Rename the low_power_ctrl field to low_power_ctrl_an to be properly
descriptive of it being an autoneg field.
Signed-off-by: Lev Faerman <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: Paul Greenwalt <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add debug logs for ice_aq_get_phy_caps(), and format
ice_aq_set_phy_cfg() and ice_aq_get_link_info() debug logs to make them
more readable.
Signed-off-by: Paul Greenwalt <[email protected]>
Signed-off-by: Paul M Stillwell Jr <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When the Port Disable bit is set in the Link Default Override Mask TLV PFA
module in the NVM, Total Port Shutdown mode is supported and enabled. In
this mode, the driver should act as if the link-down-on-close ethtool
private flag is always enabled and dis-allow any change to that flag.
Signed-off-by: Bruce Allan <[email protected]>
Signed-off-by: Paul Greenwalt <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <[email protected]>
Signed-off-by: Evan Swanson <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <[email protected]>
Signed-off-by: Chinh T Cao <[email protected]>
Signed-off-by: Paul M Stillwell Jr <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The call to ice_cfg_phy_fec() requires the caller to perform certain
actions before calling it. Instead of imposing these preconditions move
the operations into the function and perform them ourselves.
Also, fix some style issues in nearby touched code.
Signed-off-by: Paul Greenwalt <[email protected]>
Signed-off-by: Chinh T Cao <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Create a helper function for configuring requested flow control so that it
can be utilized by other functions looking to configure flow control
settings. Utilize the existing helper ice_copy_phy_caps_to_cfg() to copy a
PHY capability to configuration instead duplicating the code for it.
Signed-off-by: Paul Greenwalt <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: Akeem G Abodunrin <[email protected]>
Signed-off-by: Jesse Brandeburg <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Using the new ice_aq_list_caps and ice_parse_(dev|func)_caps functions,
replace ice_discover_caps with two functions that each take a pointer to
the dev_caps and func_caps structures respectively.
This makes the side effect of updating the hw->dev_caps and
hw->func_caps obvious from reading the implementation of the function.
Additionally, it opens the way for enabling reading of device
capabilities outside of the initialization flow. By passing in
a pointer, another caller will be able to read the capabilities without
modifying the HW capabilities structures.
As there are no other callers, it is safe to now remove
ice_aq_discover_caps and ice_parse_caps.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice_parse_caps function is used to convert the capability block data
coming from firmware into a structured format used by other parts of the
code.
The current implementation directly updates the hw->func_caps and
hw->dev_caps structures. It is directly called from within
ice_aq_discover_caps. This causes the discover_caps function to have the
side effect of modifying the HW capability structures, which is not
intuitive.
Split this function into ice_parse_dev_caps and ice_parse_func_caps.
These functions will take a pointer to the dev_caps and func_caps
respectively. Also create an ice_parse_common_caps for sharing the
capability logic that is common to device and function.
Doing so enables a future refactor to allow reading and parsing
capabilities into a local caps structure instead of modifying the
members of the HW structure directly.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The ice_discover_caps function is used to read the device and function
capabilities, updating the hardware capabilities structures with
relevant data.
The exact number of capabilities returned by the hardware is unknown
ahead of time. The AdminQ command will report the total number of
capabilities in the return buffer.
The current implementation involves requesting capabilities once,
reading this returned size, and then re-requested with that size.
This isn't really necessary. The firmware interface has a maximum size
of ICE_AQ_MAX_BUF_LEN. Firmware can never return more than
ICE_AQ_MAX_BUF_LEN / sizeof(struct ice_aqc_list_caps_elem) capabilities.
Avoid the retry loop by simply allocating a buffer of size
ICE_AQ_MAX_BUF_LEN. This is significantly simpler than retrying. The
extra allocation isn't a big deal, as it will be released after we
finish parsing the capabilities.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Straightforward conversion to new infra. Driver restores info
after close/open cycle by calling its internal restore function
so just use that, no need for udp_tunnel_nic_reset_ntf() here.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Make use of new common udp_tunnel_nic infra. ixgbe supports
IPv4 only, and only single VxLAN and Geneve ports (one each).
v2:
- split out the RXCSUM feature handling to separate change;
- declare structs separately;
- use ti.type instead of assuming table 0 is VxLAN;
- move setting netdev->udp_tunnel_nic_info to its own switch.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It appears the clearing of UDP tunnel ports when RXCSUM
is disabled is unnecessary. Driver will not pay attention
to checksum bits if RXCSUM is not set, so we can let
the hardware parse the packets.
Note that the UDP tunnel port NDO handlers don't pay attention
to the state of RXCSUM, so the ports could had been re-programmed,
anyway.
This cleanup simplifies later conversion patch.
v2:
- break this out of the following patch.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, devlink_port_attrs_set accepts a long list of parameters,
that most of them are devlink port's attributes.
Use the devlink_port_attrs struct to replace the relevant parameters.
Signed-off-by: Danielle Ratson <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The method struct pci_error_handlers.error_detected() is defined and
documented as taking an 'enum pci_channel_state' for the second argument,
but most drivers use 'pci_channel_state_t' instead.
This 'pci_channel_state_t' is not a typedef for the enum but a typedef for
a bitwise type in order to have better/stricter typechecking.
Consolidate everything by using 'pci_channel_state_t' in the method's
definition, in the related helpers and in the drivers.
Enforce use of 'pci_channel_state_t' by replacing 'enum pci_channel_state'
with an anonymous 'enum'.
Note: Currently, from a typechecking point of view this patch changes
nothing because only the constants defined by the enum are bitwise, not the
enum itself (sparse doesn't have the notion of 'bitwise enum'). This may
change in some not too far future, hence the patch.
[bhelgaas: squash in
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/r/[email protected]]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Luc Van Oostenryck <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-07-01
This series contains updates to all Intel drivers, but a majority of the
changes are to the i40e driver.
Jeff converts 'fall through' comments to the 'fallthrough;' keyword for
all Intel drivers. Removed unnecessary delay in the ixgbe ethtool
diagnostics test.
Arkadiusz implements Total Port Shutdown for i40e. This is the revised
patch based on Jakub's feedback from an earlier submission of this
patch, where additional code comments and description was needed to
describe the functionality.
Wei Yongjun fixes return error code for iavf_init_get_resources().
Magnus optimizes XDP code in i40e; starting with AF_XDP zero-copy
transmit completion path. Then by only executing a division when
necessary in the napi_poll data path. Move the check for transmit ring
full outside the send loop to increase performance.
Ciara add XDP ring statistics to i40e and the ability to dump these
statistics and descriptors.
Tony fixes reporting iavf statistics.
Radoslaw adds support for 2.5 and 5 Gbps by implementing the newer ethtool
ksettings API in ixgbe.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Convert the pre-C90-extension "C struct hack" method (using a single-
element array at the end of a structure for implementing variable-length
types) to the preferred use of C99 flexible array member.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There are a number of structures that consist of a one-element array as the
only struct member. Some of those are unused so remove them. Others are
used to index into a buffer/array consisting of a variable number of a
different data or structure type. Those are unnecessary since we can use
simple pointer arithmetic or index directly into the buffer to access
individual elements of the buffer/array.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Add a new devlink region used for capturing a snapshot of the device
capabilities buffer which is reported by the firmware over the AdminQ.
This information can useful in debugging driver and firmware
interactions.
Signed-off-by: Jacob Keller <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Added full support for new version Ethtool API. New API allow use
2500Gbase-T and 5000base-T supported and advertised link speed modes.
Signed-off-by: Radoslaw Tyl <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There is a 4 seconds delay in ixgbe_diag_test() that is holding up other
ioctls such as SIOCGIFCONF that Oracle database applications use.
One of Oracle's product runs "ethtool -t ethX online" periodically for
system monitoring and that is impacting database applications that use
SIOCGIFCONF at that same time.
This 4 second delay was needed in out early 1GbE parts to give the PHY
time to recover from a reset. This code was carried forward to the 10 GbE
driver even it was not needed for the supported PHYs in the ixgbe driver.
CC: Aleksandr Loktionov <[email protected]>
CC: Jack Vogel <[email protected]>
Reported-by: Venkat Venkatsubra <[email protected]>
Signed-off-by: Jeff Kirsher <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Commit bac8486116b0 ("iavf: Refactor the watchdog state machine") inverted
the logic for when to update statistics. Statistics should be updated when
no other commands are pending, instead they were only requested when a
command was processed. iavf_request_stats() would see a pending request
and not request statistics to be updated. This caused statistics to never
be updated; fix the logic.
Fixes: bac8486116b0 ("iavf: Refactor the watchdog state machine")
Signed-off-by: Tony Nguyen <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
|
|
Interfaces already exist for dumping Rx and Tx descriptor information.
Introduce another for doing the same for XDP descriptors.
Signed-off-by: Ciara Loftus <[email protected]>
Tested-by: Andrew Bowers <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|