| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-02-01
This series contains updates to e1000e driver only.
Sasha removes CSME handshake with TGL platform as this is not supported
and is causing hardware unit hangs to be reported.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: Handshake with CSME starts from ADL platforms
e1000e: Separate ADP board type from TGP
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Handshake with CSME/AMT on none provisioned platforms during S0ix flow
is not supported on TGL platform and can cause to HW unit hang. Update
the handshake with CSME flow to start from the ADL platform.
Fixes: 3e55d231716e ("e1000e: Add handshake with the CSME to support S0ix")
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
We have the same LAN controller on different PCH's. Separate ADP board
type from a TGP which will allow for specific fixes to be applied for
ADP platforms.
Suggested-by: Kai-Heng Feng <[email protected]>
Suggested-by: Dima Ruinskiy <[email protected]>
Signed-off-by: Sasha Neftin <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Fix the crash in kernel while dereferencing the NULL pointer,
when the driver is unloaded and simultaneously the VSI rings
are being stopped.
The hardware requires 50msec in order to finish RX queues
disable. For this purpose the driver spins in mdelay function
for the operation to be completed.
For example changing number of queues which requires reset would
fail in the following call stack:
1) i40e_prep_for_reset
2) i40e_pf_quiesce_all_vsi
3) i40e_quiesce_vsi
4) i40e_vsi_close
5) i40e_down
6) i40e_vsi_stop_rings
7) i40e_vsi_control_rx -> disable requires the delay of 50msecs
8) continue back in i40e_down function where
i40e_clean_tx_ring(vsi->tx_rings[i]) is going to crash
When the driver was spinning vsi_release called
i40e_vsi_free_arrays where the vsi->tx_rings resources
were freed and the pointer was set to NULL.
Fixes: 5b6d4a7f20b0 ("i40e: Fix crash during removing i40e driver")
Signed-off-by: Slawomir Laba <[email protected]>
Signed-off-by: Sylwester Dziedziuch <[email protected]>
Signed-off-by: Karen Sornek <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There was an AQ error I40E_AQ_RC_EINVAL when trying
to reset bw limit as part of bw allocation setup.
This was caused by trying to reset bw limit with
DCB enabled. Bw limit should not be reset when
DCB is enabled. The code was relying on the pf->flags
to check if DCB is enabled but if only 1 TC is available
this flag will not be set even though DCB is enabled.
Add a check for number of TC and if it is 1
don't try to reset bw limit even if pf->flags shows
DCB as disabled.
Fixes: fa38e30ac73f ("i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled")
Suggested-by: Alexander Lobakin <[email protected]> # Flatten the condition
Signed-off-by: Sylwester Dziedziuch <[email protected]>
Signed-off-by: Jedrzej Jagielski <[email protected]>
Reviewed-by: Alexander Lobakin <[email protected]>
Tested-by: Imam Hassan Reza Biswas <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Change i40e_update_vsi_stats and struct i40e_vsi to use u64 fields to match
the width of the stats counters in struct i40e_rx_queue_stats.
Update debugfs code to use the correct format specifier for u64.
Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Joe Damato <[email protected]>
Reported-by: kernel test robot <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Fix for failed to init adminq: -53 while VF is resetting via MAC
address changing procedure.
Added sync module to avoid reading deadbeef value in reinit adminq
during software reset.
Without this patch it is possible to trigger VF reset procedure
during reinit adminq. This resulted in an incorrect reading of
value from the AQP registers and generated the -53 error.
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <[email protected]>
Signed-off-by: Karen Sornek <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When XDP was configured on a system with large number of CPUs
and X722 NIC there was a call trace with NULL pointer dereference.
i40e 0000:87:00.0: failed to get tracking for 256 queues for VSI 0 err -12
i40e 0000:87:00.0: setup of MAIN VSI failed
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:i40e_xdp+0xea/0x1b0 [i40e]
Call Trace:
? i40e_reconfig_rss_queues+0x130/0x130 [i40e]
dev_xdp_install+0x61/0xe0
dev_xdp_attach+0x18a/0x4c0
dev_change_xdp_fd+0x1e6/0x220
do_setlink+0x616/0x1030
? ahci_port_stop+0x80/0x80
? ata_qc_issue+0x107/0x1e0
? lock_timer_base+0x61/0x80
? __mod_timer+0x202/0x380
rtnl_setlink+0xe5/0x170
? bpf_lsm_binder_transaction+0x10/0x10
? security_capable+0x36/0x50
rtnetlink_rcv_msg+0x121/0x350
? rtnl_calcit.isra.0+0x100/0x100
netlink_rcv_skb+0x50/0xf0
netlink_unicast+0x1d3/0x2a0
netlink_sendmsg+0x22a/0x440
sock_sendmsg+0x5e/0x60
__sys_sendto+0xf0/0x160
? __sys_getsockname+0x7e/0xc0
? _copy_from_user+0x3c/0x80
? __sys_setsockopt+0xc8/0x1a0
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f83fa7a39e0
This was caused by PF queue pile fragmentation due to
flow director VSI queue being placed right after main VSI.
Because of this main VSI was not able to resize its
queue allocation for XDP resulting in no queues allocated
for main VSI when XDP was turned on.
Fix this by always allocating last queue in PF queue pile
for a flow director VSI.
Fixes: 41c445ff0f48 ("i40e: main driver core")
Fixes: 74608d17fe29 ("i40e: add support for XDP_TX action")
Signed-off-by: Sylwester Dziedziuch <[email protected]>
Signed-off-by: Mateusz Palczewski <[email protected]>
Reviewed-by: Maciej Fijalkowski <[email protected]>
Tested-by: Kiran Bhandare <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Before this patch VF interface vanished when
maximum queue number was exceeded. Driver tried
to add next queues even if there was not enough
space. PF sent incorrect number of queues to
the VF when there were not enough of them.
Add an additional condition introduced to check
available space in 'qp_pile' before proceeding.
This condition makes it impossible to add queues
if they number is greater than the number resulting
from available space.
Also add the search for free space in PF queue
pair piles.
Without this patch VF interfaces are not seen
when available space for queues has been
exceeded and following logs appears permanently
in dmesg:
"Unable to get VF config (-32)".
"VF 62 failed opcode 3, retval: -5"
"Unable to get VF config due to PF error condition, not retrying"
Fixes: 7daa6bf3294e ("i40e: driver core headers")
Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Jaroslaw Gawin <[email protected]>
Signed-off-by: Slawomir Laba <[email protected]>
Signed-off-by: Jedrzej Jagielski <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Recently simplified i40e_rebuild causes that FW sometimes
is not ready after NVM update, the ping does not return.
Increase the delay in case of EMP reset.
Old delay of 300 ms was introduced for specific cards for 710 series.
Now it works for all the cards and delay was increased.
Fixes: 1fa51a650e1d ("i40e: Add delay after EMP reset for firmware to recover")
Signed-off-by: Arkadiusz Kubalewski <[email protected]>
Signed-off-by: Jedrzej Jagielski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Provide a new interface for affinity hints to provide a separation
between hint and actual affinity change which has become a hidden
property of the current interface
- Fix up the in tree usage of the affinity hint interfaces
Drivers:
- No new irqchip drivers!
- Fix GICv3 redistributor table reservation with RT across kexec
- Fix GICv4.1 redistributor view of the VPE table across kexec
- Add support for extra interrupts on spear-shirq
- Make obtaining some interrupts optional for the Renesas drivers
- Various cleanups and bug fixes"
* tag 'irq-core-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
irqchip/renesas-intc-irqpin: Use platform_get_irq_optional() to get the interrupt
irqchip/renesas-irqc: Use platform_get_irq_optional() to get the interrupt
irqchip/gic-v4: Disable redistributors' view of the VPE table at boot time
irqchip/ingenic-tcu: Use correctly sized arguments for bit field
irqchip/gic-v2m: Add const to of_device_id
irqchip/imx-gpcv2: Mark imx_gpcv2_instance with __ro_after_init
irqchip/spear-shirq: Add support for IRQ 0..6
irqchip/gic-v3-its: Limit memreserve cpuhp state lifetime
irqchip/gic-v3-its: Postpone LPI pending table freeing and memreserve
irqchip/gic-v3-its: Give the percpu rdist struct its own flags field
net/mlx4: Use irq_update_affinity_hint()
net/mlx5: Use irq_set_affinity_and_hint()
hinic: Use irq_set_affinity_and_hint()
scsi: lpfc: Use irq_set_affinity()
mailbox: Use irq_update_affinity_hint()
ixgbe: Use irq_update_affinity_hint()
be2net: Use irq_update_affinity_hint()
enic: Use irq_update_affinity_hint()
RDMA/irdma: Use irq_update_affinity_hint()
scsi: mpt3sas: Use irq_set_affinity_and_hint()
...
|
|
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c
Signed-off-by: Ingo Molnar <[email protected]>
|
|
The variable `ret_code' used for returning is never changed in function
`iavf_shutdown_adminq'. So that it can be removed and just return its
initial value 0 at the end of `iavf_shutdown_adminq' function.
Signed-off-by: Jason Wang <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The code that uses variables pe_cntx_size and pe_filt_size
has been removed, so they should be removed as well.
Eliminate the following clang warnings:
drivers/net/ethernet/intel/i40e/i40e_common.c:4139:20:
warning: variable 'pe_filt_size' set but not used.
drivers/net/ethernet/intel/i40e/i40e_common.c:4139:6:
warning: variable 'pe_cntx_size' set but not used.
Reported-by: Abaci Robot <[email protected]>
Signed-off-by: Yang Li <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Remove non-inclusive language from the driver.
Signed-off-by: Aleksandr Loktionov <[email protected]>
Signed-off-by: Mateusz Palczewski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Update FW API versions to the newest supported NVM images.
Signed-off-by: Sylwester Dziedziuch <[email protected]>
Signed-off-by: Mateusz Palczewski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The i40e_asq_send_command will now use a non blocking usleep_range if
possible (non-atomic context), instead of busy-waiting udelay. The
usleep_range function uses hrtimers to provide better performance and
removes the negative impact of busy-waiting in time-critical
environments.
1. Rename i40e_asq_send_command to i40e_asq_send_command_atomic
and add 5th parameter to inform if called from an atomic context.
Call inside usleep_range (if non-atomic) or udelay (if atomic).
2. Change i40e_asq_send_command to invoke
i40e_asq_send_command_atomic(..., false).
3. Change two functions:
- i40e_aq_set_vsi_uc_promisc_on_vlan
- i40e_aq_set_vsi_mc_promisc_on_vlan
to explicitly use i40e_asq_send_command_atomic(..., true)
instead of i40e_asq_send_command, as they use spinlocks and do some
work in an atomic context.
All other calls to i40e_asq_send_command remain unchanged.
Signed-off-by: Dawid Lukwinski <[email protected]>
Signed-off-by: Jedrzej Jagielski <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Trusted VF can use up every resource available, leaving nothing
to other trusted VFs.
Introduce define, which calculates MacVlan resources available based
on maximum available MacVlan resources, bare minimum for each VF and
number of currently allocated VFs.
Signed-off-by: Przemyslaw Patynowski <[email protected]>
Signed-off-by: Karen Sornek <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
kfree() and bitmap_free() are the same. But using the latter is more
consistent when freeing memory allocated with bitmap_zalloc().
Signed-off-by: Christophe JAILLET <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When a bitmap is local to a function, it is safe to use the non-atomic
__[set|clear]_bit(). No concurrent accesses can occur.
Signed-off-by: Christophe JAILLET <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The 'possible_idx' bitmap is set just after it is zeroed, so we can save
the first step.
The 'free_idx' bitmap is used only at the end of the function as the
result of a bitmap xor operation. So there is no need to explicitly
zero it before.
So, slightly simply the code and remove 2 useless 'bitmap_zero()' call
Signed-off-by: Christophe JAILLET <[email protected]>
Tested-by: Sandeep Penigalapati <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In current switchdev implementation, every VF PR is assigned to
individual ring on switchdev ctrl VSI. For slow-path traffic, there
is a mapping VF->ring done in software based on src_vsi value (by
calling ice_eswitch_get_target_netdev function).
With this change, HW solution is introduced which is more
efficient. For each VF, src MAC (VF's MAC) filter will be created,
which forwards packets to the corresponding switchdev ctrl VSI queue
based on src MAC address.
This filter has to be removed and then replayed in case of
resetting one VF. Keep information about this rule in repr->mac_rule,
thanks to that we know which rule has to be removed and replayed
for a given VF.
In case of CORE/GLOBAL all rules are removed
automatically. We have to take care of readding them. This is done
by ice_replay_vsi_adv_rule.
When driver leaves switchdev mode, remove all advanced rules
from switchdev ctrl VSI. This is done by ice_rem_adv_rule_for_vsi.
Flag repr->rule_added is needed because in some cases reset
might be triggered before VF sends request to add MAC.
Co-developed-by: Grzegorz Nitka <[email protected]>
Signed-off-by: Grzegorz Nitka <[email protected]>
Signed-off-by: Wojciech Drewek <[email protected]>
Tested-by: Sandeep Penigalapati <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
ice_replay_vsi_adv_rule will replay advanced rules for a given VSI.
Exit this function when list of rules for given recipe is empty.
Do not add rule when given vsi_handle does not match vsi_handle
from the rule info.
Use ICE_MAX_NUM_RECIPES instead of ICE_SW_LKUP_LAST in order to find
advanced rules as well.
Signed-off-by: Victor Raj <[email protected]>
Signed-off-by: Wojciech Drewek <[email protected]>
Tested-by: Sandeep Penigalapati <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
In the absence of this validation, if the user requests to
configure queues more than the enabled queues, it results in
sending the requested number of queues to the kernel stack
(due to the asynchronous nature of VF response), in which
case the stack might pick a queue to transmit that is not
enabled and result in Tx hang. Fix this bug by
limiting the total number of queues allocated for VF to
active queues of VF.
Fixes: d5b33d024496 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Ashwin Vijayavel <[email protected]>
Signed-off-by: Karen Sornek <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
There was a wrong queues representation in sysfs during
driver's reinitialization in case of online cpus number is
less than combined queues. It was caused by stopped
NetworkManager, which is responsible for calling vsi_open
function during driver's initialization.
In specific situation (ex. 12 cpus online) there were 16 queues
in /sys/class/net/<iface>/queues. In case of modifying queues with
value higher, than number of online cpus, then it caused write
errors and other errors.
Add updating of sysfs's queues representation during driver
initialization.
Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Lukasz Cieplicki <[email protected]>
Signed-off-by: Jedrzej Jagielski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
When loading the i40e driver, it prints a message like: 'The driver for the
device detected a newer version of the NVM image v1.x than expected v1.y.
Please install the most recent version of the network driver.' This is
misleading as the driver is working as expected.
Fix that by removing the second part of message and changing it from
dev_info to dev_dbg.
Fixes: 4fb29bddb57f ("i40e: The driver now prints the API version in error message")
Signed-off-by: Mateusz Palczewski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Using ifconfig command to delete the ipv6 address will cause
the i40e network card driver to delete its internal mac_filter and
i40e_service_task kernel thread will concurrently access the mac_filter.
These two processes are not protected by lock
so causing the following use-after-free problems.
print_address_description+0x70/0x360
? vprintk_func+0x5e/0xf0
kasan_report+0x1b2/0x330
i40e_sync_vsi_filters+0x4f0/0x1850 [i40e]
i40e_sync_filters_subtask+0xe3/0x130 [i40e]
i40e_service_task+0x195/0x24c0 [i40e]
process_one_work+0x3f5/0x7d0
worker_thread+0x61/0x6c0
? process_one_work+0x7d0/0x7d0
kthread+0x1c3/0x1f0
? kthread_park+0xc0/0xc0
ret_from_fork+0x35/0x40
Allocated by task 2279810:
kasan_kmalloc+0xa0/0xd0
kmem_cache_alloc_trace+0xf3/0x1e0
i40e_add_filter+0x127/0x2b0 [i40e]
i40e_add_mac_filter+0x156/0x190 [i40e]
i40e_addr_sync+0x2d/0x40 [i40e]
__hw_addr_sync_dev+0x154/0x210
i40e_set_rx_mode+0x6d/0xf0 [i40e]
__dev_set_rx_mode+0xfb/0x1f0
__dev_mc_add+0x6c/0x90
igmp6_group_added+0x214/0x230
__ipv6_dev_mc_inc+0x338/0x4f0
addrconf_join_solict.part.7+0xa2/0xd0
addrconf_dad_work+0x500/0x980
process_one_work+0x3f5/0x7d0
worker_thread+0x61/0x6c0
kthread+0x1c3/0x1f0
ret_from_fork+0x35/0x40
Freed by task 2547073:
__kasan_slab_free+0x130/0x180
kfree+0x90/0x1b0
__i40e_del_filter+0xa3/0xf0 [i40e]
i40e_del_mac_filter+0xf3/0x130 [i40e]
i40e_addr_unsync+0x85/0xa0 [i40e]
__hw_addr_sync_dev+0x9d/0x210
i40e_set_rx_mode+0x6d/0xf0 [i40e]
__dev_set_rx_mode+0xfb/0x1f0
__dev_mc_del+0x69/0x80
igmp6_group_dropped+0x279/0x510
__ipv6_dev_mc_dec+0x174/0x220
addrconf_leave_solict.part.8+0xa2/0xd0
__ipv6_ifa_notify+0x4cd/0x570
ipv6_ifa_notify+0x58/0x80
ipv6_del_addr+0x259/0x4a0
inet6_addr_del+0x188/0x260
addrconf_del_ifaddr+0xcc/0x130
inet6_ioctl+0x152/0x190
sock_do_ioctl+0xd8/0x2b0
sock_ioctl+0x2e5/0x4c0
do_vfs_ioctl+0x14e/0xa80
ksys_ioctl+0x7c/0xa0
__x64_sys_ioctl+0x42/0x50
do_syscall_64+0x98/0x2c0
entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Di Zhu <[email protected]>
Signed-off-by: Rui Zhang <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Hide i40e opcode information sent during response to VF in case when
untrusted VF tried to change MAC on the VF interface.
This is implemented by adding an additional parameter 'hide' to the
response sent to VF function that hides the display of error
information, but forwards the error code to VF.
Previously it was not possible to send response with some error code
to VF without displaying opcode information.
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <[email protected]>
Signed-off-by: Mateusz Palczewski <[email protected]>
Reviewed-by: Paul M Stillwell Jr <[email protected]>
Reviewed-by: Aleksandr Loktionov <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Recent bpf-next merge brought in header changes which uncovered
includes missing in net-next which were not present in bpf-next.
Build problems happen only on less-popular arches like hppa,
sparc, alpha etc.
I could repro the build problem with ice but not the mlx5 problem
Abdul was reporting. mlx5 does look like it should include filter.h,
anyway.
Reported-by: Abdul Haleem <[email protected]>
Fixes: e63a02348958 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next")
Link: https://lore.kernel.org/all/[email protected]/
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764c7 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f36 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0fb ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/[email protected]/
net/smc/smc_wr.c
commit 49dc9013e34b ("net/smc: Use the bitmap API when applicable")
commit 349d43127dac ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add support to enable flow-director filter when multiple TCs are
configured. Flow director filter can be configured using ethtool
(--config-ntuple option). When multiple TCs are configured, each
TC is mapped to an unique HW VSI. So VSI corresponding to queue
used in filter is identified and flow director context is updated
with correct VSI while configuring ntuple filter in HW.
Signed-off-by: Kiran Patil <[email protected]>
Signed-off-by: Amritha Nambiar <[email protected]>
Signed-off-by: Sudheer Mogilappagari <[email protected]>
Tested-by: Bharathi Sreenivas <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Support for the PTP pin function on 82580/i354/i350 based adapters.
Because the time registers of these adapters do not have the nice split in
second rollovers as the i210 has, the implementation is slightly more
complex compared to the i210 implementation.
Signed-off-by: Ruud Bos <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Support for the PEROUT PTP pin function on 82580/i354/i350 based adapters.
Because the time registers of these adapters do not have the nice split in
second rollovers as the i210 has, the implementation is slightly more
complex compared to the i210 implementation.
Signed-off-by: Ruud Bos <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Remove code duplication in the tsync interrupt handler function by moving
this logic to separate functions. This keeps the interrupt handler readable
and allows the new functions to be extended for adapter types other than
i210.
Signed-off-by: Ruud Bos <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Allow reuse of SDP config struct initialization by moving it to a
separate function.
Signed-off-by: Ruud Bos <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Acked-by: Marc Kleine-Budde <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Acked-by: Nikolay Aleksandrov <[email protected]>
Acked-by: Stefano Garzarella <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Time synchronization was not properly enabled on non-MSI-X platforms.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Signed-off-by: James McLaughlin <[email protected]>
Reviewed-by: Vinicius Costa Gomes <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
It was reported that when PCIe PTM is enabled, some lockups could
be observed with some integrated i225-V models.
While the issue is investigated, we can disable crosstimestamp for
those models and see no loss of functionality, because those models
don't have any support for time synchronization.
Fixes: a90ec8483732 ("igc: Add support for PTP getcrosststamp()")
Link: https://lore.kernel.org/all/[email protected]/
Reported-by: Stefan Dietrich <[email protected]>
Signed-off-by: Vinicius Costa Gomes <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
ixgbevf driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
ixgbe driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
igc driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Nechama Kraus <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
igb driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
ice driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
iavf driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Konrad Jankowski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx.
i40e driver runs Tx completion polling cycle right before the Rx
one and uses napi_consume_skb() to feed the cache with skbuff_heads
of completed entries, so it's never empty and always warm at that
moment. Switch to the napi_build_skb() to relax mm pressure on
heavy Rx.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Gurucharan G <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
napi_build_skb() reuses per-cpu NAPI skbuff_head cache in order
to save some cycles on freeing/allocating skbuff_heads on every
new Rx or completed Tx element.
e1000 driver runs Tx completion polling cycle right before the Rx
one. Now that e1000 uses napi_consume_skb() to put skbuff_heads of
completed entries into the cache, it will never empty and always
warm at that moment. Switch to the napi_build_skb() to relax mm
pressure on heavy Rx and increase throughput.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
In order to take the best from per-cpu NAPI skbuff_head caches and
CPU cycles, let's switch from dev_kfree_skb_any(), which passes skb
back to the mm layer, to napi_consume_skb(), which feeds those
caches on non-zero budget instead (falls back to the former on 0).
Do the replacement in e1000_unmap_and_free_tx_resource(). There are
4 call sites of this function throughout the driver:
* e1000_clean_tx_ring(). Slowpath, process context, cleans the
whole Tx ring on ifdown. Use budget of 0 here;
* e1000_tx_map(). Hotpath, net Tx softirq, unmaps the buffers in
case of error. Use 0 as well;
* e1000_clean_tx_irq(). Hotpath, NAPI Tx completion polling cycle.
As the driver doesn't count completed Tx entries towards the NAPI
budget, just use the poll budget of 64 to utilize caches.
Apart from being a preparation for switching to napi_build_skb(),
this is useful on its own as well, as napi_consume_skb() flushes
skb caches by batches of 32 instead of one-at-a-time.
Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Michal Swiatkowski <[email protected]>
Tested-by: Tony Brelinski <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
include/net/sock.h
commit 8f905c0e7354 ("inet: fully convert sk->sk_rx_dst to RCU rules")
commit 43f51df41729 ("net: move early demux fields close to sk_refcnt")
https://lore.kernel.org/all/[email protected]/
Signed-off-by: Jakub Kicinski <[email protected]>
|