| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The new HDMI connector infrastructure allows us to remove a lot of
boilerplate, so let's switch to it.
Acked-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Link: https://patchwork.freedesktop.org/patch/msgid/20240527-kms-hdmi-connector-state-v15-25-c5af16c3aae2@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Copy Intel's "Broadcast RGB" property semantics to add manual override
of the HDMI pixel range for monitors that don't abide by the content
of the AVI Infoframe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco at xs4all.nl>
Link: https://lore.kernel.org/r/20221207-rpi-hdmi-improvements-v3-3-bdd54f66884e@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
container_of_const() allows to preserve the pointer constness and is
thus more flexible than inline functions.
Let's switch all our instances of container_of() to
container_of_const().
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20221207-rpi-hdmi-improvements-v3-1-bdd54f66884e@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
This reverts commit 3bc6a37f59f21a8bfaf74d0975b2eb0b2d52a065.
Commit 3bc6a37f59f2 ("drm/vc4: hdmi: Fix HSM clock too low on Pi4") was
introduced to work around an issue partly due to the clk-bcm2835 driver
on the RaspberryPi0-3.
Since we're not using that driver for our HDMI clocks, we can now revert
that inelegant solution.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20230126-rpi-display-fw-clk-cleanup-v1-3-d646ff6fb842@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Linux 6.1-rc6
This is needed for drm-misc-next and tegra.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Commit ae71ab585c81 ("drm/vc4: hdmi: Enforce the minimum rate at
runtime_resume") reintroduced the call to clk_set_min_rate in an attempt
to fix the boot without a monitor connected on the RaspberryPi3.
However, that introduced a regression breaking the display output
entirely (black screen but no vblank timeout) on the Pi4.
This is due to the fact that we now have in a typical modeset at boot,
in vc4_hdmi_encoder_pre_crtc_configure(), we have a first call to
clk_set_min_rate() asking for the minimum rate of the HSM clock for our
given resolution, and then a call to pm_runtime_resume_and_get(). We
will thus execute vc4_hdmi_runtime_resume() which, since the commit
mentioned above, will call clk_set_min_rate() a second time with the
absolute minimum rate we want to enforce on the HSM clock.
We're thus effectively erasing the minimum mandated by the mode we're
trying to set. The fact that only the Pi4 is affected is due to the fact
that it uses a different clock driver that tries to minimize the HSM
clock at all time. It will thus lower the HSM clock rate to 120MHz on
the second clk_set_min_rate() call.
The Pi3 doesn't use the same driver and will not change the frequency on
the second clk_set_min_rate() call since it's still within the new
boundaries and it doesn't have the code to minimize the clock rate as
needed. So even though the boundaries are still off, the clock rate is
still the right one for our given mode, so everything works.
There is a lot of moving parts, so I couldn't find any obvious
solution:
- Reverting the original is not an option, as that would break the Pi3
again.
- We can't move the clk_set_min_rate() call in _pre_crtc_configure()
since because, on the Pi3, the HSM clock has the CLK_SET_RATE_GATE
flag which prevents the clock rate from being changed after it's
been enabled. Our calls to clk_set_min_rate() can change it, so they
need to be done before clk_prepare_enable().
- We can't remove the call to clk_prepare_enable() from the
runtime_resume hook to put it into _pre_crtc_configure() either,
since we need that clock to be enabled to access the registers, and
we can't count on the fact that the display will be active in all
situations (doing any CEC operation, or listing the modes while
inactive are valid for example()).
- We can't drop the call to clk_set_min_rate() in
_pre_crtc_configure() since we would need to still enforce the
minimum rate for a given resolution, and runtime_resume doesn't have
access to the current mode, if there's any.
- We can't copy the TMDS character rate into vc4_hdmi and reuse it
since, because it's part of the KMS atomic state, it needs to be
protected by a mutex. Unfortunately, some functions (CEC operations,
mostly) can be reentrant (through the CEC framework) and still need
a pm_runtime_get.
However, we can work around this issue by leveraging the fact that the
clk_set_min_rate() calls set boundaries for its given struct clk, and
that each different clk_get() call will return a different instance of
struct clk. The clock framework will then aggregate the boundaries for
each struct clk instances linked to a given clock, plus its hardware
boundaries, and will use that.
We can thus get an extra HSM clock user for runtime_pm use only, and use
our different clock instances depending on the context: runtime_pm will
use its own to set the absolute minimum clock setup so that we never
lock the CPU waiting for a register access, and the modeset part will
set its requirement for the current resolution. And we let the CCF do
the coordination.
It's not an ideal solution, but it's fairly unintrusive and doesn't
really change any part of the logic so it looks like a rather safe fix.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2136234
Fixes: ae71ab585c81 ("drm/vc4: hdmi: Enforce the minimum rate at runtime_resume")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20221021131339.2203291-1-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
In order to support higher HDMI frequencies, users have to set the
hdmi_enable_4kp60 parameter in their config.txt file.
This will have the side-effect of raising the maximum of the core clock,
tied to the HVS, and managed by the HVS driver.
However, we are querying this in the HDMI driver by poking into the HVS
structure to get our struct clk handle.
Let's make this part of the HVS bind implementation to have all the core
clock related setup in the same place.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-5-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
We recently introduced a new mutex to protect concurrent execution of
ALSA and KMS hooks, and the concurrent access to some of vc4_hdmi
fields.
However, using it in the detect hook was creating a reentrency issue
with CEC code. Indeed, calling cec_s_phys_addr_from_edid from detect
might call the CEC adap_enable hook with the lock held, eventually
resulting in a deadlock.
Since we didn't really need to protect anything at the moment in the CEC
code, the decision was made to ignore the mutex in those CEC hooks,
working around the issue.
However, we can have the same thing happening if we end up triggering a
mode set from the detect callback, for example using
drm_atomic_helper_connector_hdmi_reset_link().
Since we don't really need to protect anything in detect either, let's
just drop the lock in detect, and add it again in CEC.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-4-maxime@cerno.tech
|
|
We don't modify the drm_display_mode pointer we have in the driver in
most places, so let's make them const.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-2-maxime@cerno.tech
|
|
The current code to build the registers set later exposed in debugfs for
the HDMI controller relies on traditional allocations, that are later
free'd as part of the driver unbind hook.
Since krealloc doesn't have a DRM-managed equivalent, let's add an action
to free the buffer later on.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-45-maxime@cerno.tech
|
|
This path actually occurs when audio is started during a hdmi mode set.
As the data will be written by vc4_hdmi_set_infoframes when packet RAM
is enabled again, don't treat as an error
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-26-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The current HDMI driver, in vc4_hdmi_audio_can_stream() checks whether
the display output is enabled.
This has been there in one form or the other since the introduction of
the audio support in the VC4 HDMI driver in commit bb7d78568814
("drm/vc4: Add HDMI audio support"), but no justification for this check
is in the commit message, or in the discussions around the patches.
One can only assume this was done to prevent a user from playing audio
on the ALSA soundcard when the monitor doesn't support it.
However, this is causing some issues. Indeed, Kodi, for example, was
hitting some errors if it was streaming audio during a modeset. With the
theory above, it does make sense, but the display and audio threads are
typically completely different processes with no opportunity to
synchronise which makes it hard to workaround.
Removing that check also doesn't seem to cause any trouble, so let's
just remove it.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-25-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The vc5 HDMI registers hadn't been added into the debugfs
register sets, therefore weren't dumped on request.
Add them in.
Fixes: 8323989140f3 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-19-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The vc4_hdmi_encoder struct was used exclusively to cache the value
returned by drm_detect_hdmi_monitor() in order to avoid calling it
multiple times.
Now that drm_detect_hdmi_monitor() has been replaced with
drm_display_info.is_hdmi, there is no need to have an extra struct.
Remove vc4_hdmi_encoder.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420114500.187664-3-jose.exposito89@gmail.com
|
|
Once EDID is parsed, the monitor HDMI support information is cached in
drm_display_info.is_hdmi by drm_parse_hdmi_vsdb_video().
This driver calls drm_detect_hdmi_monitor() to receive the same
information and stores its own cached value in
vc4_hdmi_encoder.hdmi_monitor, which is less efficient.
Avoid calling drm_detect_hdmi_monitor() and use drm_display_info.is_hdmi
instead. This also allows to remove vc4_hdmi_encoder.hdmi_monitor.
drm_detect_hdmi_monitor() is called in vc4_hdmi_connector_detect() and
vc4_hdmi_connector_get_modes(). In both cases it is safe to rely on
drm_display_info.is_hdmi as shown by ftrace:
$ sudo trace-cmd record -p function_graph -l "vc4_hdmi_*" -l "drm_*"
vc4_hdmi_connector_detect:
vc4_hdmi_connector_detect() {
drm_get_edid() {
drm_connector_update_edid_property() {
drm_add_display_info() {
drm_reset_display_info();
drm_for_each_detailed_block.part.0();
drm_parse_cea_ext() {
drm_find_cea_extension();
drm_parse_hdmi_vsdb_video();
/* drm_display_info.is_hdmi is cached here */
}
}
}
}
/* drm_display_info.is_hdmi is used here */
}
vc4_hdmi_connector_get_modes:
vc4_hdmi_connector_get_modes() {
drm_get_edid() {
drm_connector_update_edid_property() {
drm_add_display_info() {
drm_reset_display_info();
drm_for_each_detailed_block.part.0();
drm_parse_cea_ext() {
drm_find_cea_extension();
drm_parse_hdmi_vsdb_video();
/* drm_display_info.is_hdmi is cached here */
}
}
}
}
/* drm_display_info.is_hdmi is used here */
drm_connector_update_edid_property();
}
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420114500.187664-2-jose.exposito89@gmail.com
|
|
Let's start the 5.19 development cycle.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
In addition to the RGB444 output, the BCM2711 HDMI controller supports
the YUV444 and YUV422 output formats.
Let's add support for them in the driver, but still use RGB as the
preferred format.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-8-maxime@cerno.tech
|
|
Currently we take the max_bpc property as the bpc value and do not try
anything else.
However, what the other drivers seem to be doing is that they would try
with the highest bpc allowed by the max_bpc property and the hardware
capabilities, test if it results in an acceptable configuration, and if
not decrease the bpc and try again.
Let's use the same logic.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-7-maxime@cerno.tech
|
|
The current code only base its decision for whether the scrambler must be
enabled or not on the pixel clock of the mode, but doesn't take the bits
per color into account.
Let's leverage the new function to compute the clock rate in the
scrambler setup code.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-6-maxime@cerno.tech
|
|
The pixel_rate field in the vc4_hdmi_connector_state struct actually
stores the TMDS character rate, let's rename it for consistency.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-2-maxime@cerno.tech
|
|
This backmerges v5.17-rc6 so I can merge some amdgpu and some tegra changes on top.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
On bind we will register the HDMI codec device but we don't unregister
it on unbind, leading to a device leakage. Unregister our device at
unbind.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127111452.222002-1-maxime@cerno.tech
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Daniel asked for this for some intel deps, so let's do it now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The existing logic was flawed in that it could try reading the
2711 specific registers for HPD on a CM1/3 where the HPD GPIO
hadn't been defined in DT.
Ensure we don't do the 2711 register read on invalid hardware,
and then
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127131754.236074-1-maxime@cerno.tech
|
|
In order to support the YUV output, we'll need the atomic state to know
what is the state of the associated property in the CSC setup callback.
Let's change the prototype of that callback to allow us to access it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-11-maxime@cerno.tech
|
|
The CSC callbacks takes a boolean as an argument to tell whether we're
using the full range or limited range RGB.
However, with the upcoming YUV support, the logic will be a bit more
complex. In order to address this, let's make the callbacks take the
entire mode, and call our new helper to tell whether the full or limited
range RGB should be used.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-7-maxime@cerno.tech
|
|
We currently rely on two functions, vc4_hdmi_supports_scrambling() and
vc4_hdmi_mode_needs_scrambling() to determine if we should enable and
disable the scrambler for any given mode.
Since we might need to disable the controller at boot, we also always
run vc4_hdmi_disable_scrambling() and thus call those functions without
a mode yet, which in turns need to make some special casing in order for
it to work.
Instead of duplicating the check for whether or not we need to take care
of the scrambler in both vc4_hdmi_enable_scrambling() and
vc4_hdmi_disable_scrambling(), we can do that check only when we enable
it and store whether or not it's been enabled in our private structure.
We also need to initialize that flag at true to make sure we disable the
scrambler at boot since we can't really know its state yet.
This allows to simplify a bit that part of the driver, and removes one
user of our copy of the CRTC adjusted mode outside of KMS (since
vc4_hdmi_disable_scrambling() might be called from the hotplug interrupt
handler).
It also removes our last user of the legacy encoder->crtc pointer.
Link: https://lore.kernel.org/r/20211025141113.702757-10-maxime@cerno.tech
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
We currently poke at encoder->crtc in the ALSA code path to determine
whether the HDMI output is enabled or not, and thus whether we should
allow the audio output.
However, that pointer is deprecated and shouldn't really be used by
atomic drivers anymore. Since we have the infrastructure in place now,
let's just create a flag that we toggle to report whether the controller
is currently enabled and use that instead of encoder->crtc in ALSA.
Link: https://lore.kernel.org/r/20211025141113.702757-9-maxime@cerno.tech
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Accessing the crtc->state pointer from outside the modesetting context
is not allowed. We thus need to copy whatever we need from the KMS state
to our structure in order to access it.
However, in the vc4 HDMI driver we do use that pointer in the ALSA code
path, and potentially in the hotplug interrupt handler path.
These paths both need access to the CRTC adjusted mode in order for the
proper dividers to be set for ALSA, and the scrambler state to be
reinstated properly for hotplug.
Let's copy this mode into our private encoder structure and reference it
from there when needed. Since that part is shared between KMS and other
paths, we need to protect it using our mutex.
Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Link: https://lore.kernel.org/r/20211025141113.702757-7-maxime@cerno.tech
Fixes: bb7d78568814 ("drm/vc4: Add HDMI audio support")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The vc4 HDMI controller registers into the KMS, CEC and ALSA
frameworks.
However, no particular care is done to prevent the concurrent execution
of different framework hooks from happening at the same time.
In order to protect against that scenario, let's introduce a mutex that
relevant ALSA and KMS hooks will need to take to prevent concurrent
execution.
CEC is left out at the moment though, since the .get_modes and .detect
KMS hooks, when running cec_s_phys_addr_from_edid, can end up calling
CEC's .adap_enable hook. This introduces some reentrancy that isn't easy
to deal with properly.
The CEC hooks also don't share much state with the rest of the driver:
the registers are entirely separate, we don't share any variable, the
only thing that can conflict is the CEC clock divider setup that can be
affected by a mode set.
However, after discussing it, it looks like CEC should be able to
recover from this if it was to happen.
Link: https://lore.kernel.org/r/20211025141113.702757-6-maxime@cerno.tech
Fixes: bb7d78568814 ("drm/vc4: Add HDMI audio support")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The vc4 HDMI driver has multiple path shared between the CEC, ALSA and
KMS frameworks, plus two interrupt handlers (CEC and hotplug) that will
read and modify a number of registers.
Even though not bug has been reported so far, it's definitely unsafe, so
let's just add a spinlock to protect the register access of the HDMI
controller.
Link: https://lore.kernel.org/r/20211025141113.702757-5-maxime@cerno.tech
Fixes: c8b75bca92cb ("drm/vc4: Add KMS support for Raspberry Pi.")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The vc4_hdmi_audio_prepare function and the functions it's calling have
in several occurences multiple dereferences of either the sample rate or
the number of channels.
It turns out that these variables are also passed through the hdmi codec
parameters structure. Convert all the users to use this structure, and
if it's used multiple times use a variable to store it instead of
dereferencing it every time.
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707093632.1468127-1-maxime@cerno.tech
|
|
The hdmi-codec brings a lot of advanced features, including the HDMI
channel mapping. Let's use it in our driver instead of our own codec.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525132354.297468-11-maxime@cerno.tech
|
|
The new gpiod interface takes care of parsing the GPIO flags and to
return the logical value when accessing an active-low GPIO, so switching
to it simplifies a lot the driver.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210524131852.263883-2-maxime@cerno.tech
|
|
It looks like some displays (like the LG 27UL850-W) don't enable the
scrambling when the HDMI driver enables it. However, if we set later the
scrambler enable bit, the display will work as expected.
Let's create delayed work queue to periodically look at the display
scrambling status, and if it's not set yet try to enable it again.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-12-maxime@cerno.tech
|
|
In order to reach the frequencies needed to output at 594MHz, the
firmware needs to be configured with the appropriate parameters in the
config.txt file (enable_hdmi_4kp60 and force_turbo).
Let's detect it at bind time, warn the user if we can't, and filter out
the relevant modes.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-10-maxime@cerno.tech
|
|
Now that we can export deeper colour depths, add in the signalling
for HDR metadata.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430094451.2145002-3-maxime@cerno.tech
|
|
Now that our HDMI controller supports CEC for the BCM2711, let's remove
that flag.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-12-maxime@cerno.tech
|
|
The HDMI controller found in the BCM2711 has an external interrupt
controller for the CEC and hotplug interrupt shared between the two
instances.
Let's add a variant flag to register a single interrupt handler and
deals with the interrupt handler setup, or two interrupt handlers
relying on an external irqchip.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-11-maxime@cerno.tech
|
|
While the BCM2835 had the CEC clock derived from the HSM clock, the
BCM2711 has a dedicated parent clock for it.
Let's introduce a separate clock for it so that we can handle both
cases.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-9-maxime@cerno.tech
|
|
The BCM2711 supports higher bpc count than just 8, so let's support it in
our driver.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-10-maxime@cerno.tech
|
|
The PHY initialisation parameters are not based on the pixel clock but
the TMDS clock rate which can be the pixel clock in the standard case,
but could be adjusted based on some parameters like the bits per color.
Since the TMDS clock rate is stored in our custom connector state
already, let's reuse it from there instead of computing it again.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-8-maxime@cerno.tech
|
|
The pixel rate is for now quite simple to compute, but with more features
(30 and 36 bits output, YUV output, etc.) will depend on a bunch of
connectors properties.
Let's store the rate we have to run the pixel clock at in our custom
connector state, and compute it in atomic_check.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-7-maxime@cerno.tech
|
|
When run with a higher bpc than 8, the clock of the HDMI controller needs
to be adjusted. Let's create a connector state that will be used at
atomic_check and atomic_enable to compute and store the clock rate
associated to the state.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-6-maxime@cerno.tech
|
|
There's cross-talk on the RPi4 between the 2.4GHz channels used by the WiFi
chip and some resolutions, most notably 1440p at 60Hz.
In such a case, we can either reject entirely the mode, or lower slightly
the pixel frequency to remove the overlap. Let's go for the latter.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029134018.1948636-2-maxime@cerno.tech
|
|
The FIFO between the pixelvalve and the HDMI controller runs at 2 pixels
per clock cycle, and cannot deal with odd timings.
Let's reject any mode with such timings.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029122522.1917579-2-maxime@cerno.tech
|
|
Now that the driver is ready for it, let's bring in the HDMI controllers
variants for the BCM2711.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b540c7a9ebb7ad51da39271a8388b69c7e27e582.1599120059.git-series.maxime@cerno.tech
|
|
The BCM2711 has another clock that needs to be ramped up depending on the
pixel rate: the pixel BVB clock. Add the code to adjust that clock when
changing the mode.
[Maxime: Changed the commit log, used clk_set_min_rate]
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20200901040759.29992-3-hoegeun.kwon@samsung.com
Link: https://patchwork.freedesktop.org/patch/msgid/d757ddd6549da140f178563e5fd2bf1d129913fd.1599120059.git-series.maxime@cerno.tech
|
|
The HDMI driver was registering a single ALSA card so far with the name
vc4-hdmi.
Obviously, this is not going to work anymore when we will have multiple
HDMI controllers since we will end up trying to register two files with the
same name.
Let's use the variant to avoid that name conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e60a37444e848a384a45707a21d6df8883115f86.1599120059.git-series.maxime@cerno.tech
|
|
The audio configuration has changed for the BCM2711, with notably a
different parent clock and a different channel configuration.
Make that modular to be able to support the BCM2711.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/85a8ca721c2d800be758c55870cea98536749680.1599120059.git-series.maxime@cerno.tech
|