| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull SoC devicetree updates from Arnd Bergmann:
"New SoC support for Broadcom bcm2712 (Raspberry Pi 5) and Renesas
R9A09G057 (RZ/V2H(P)) and Qualcomm Snapdragon 414 (MSM8929), all three
of these are variants of already supported chips, in particular the
last one is almost identical to MSM8939.
Lots of updates to Mediatek, ASpeed, Rockchips, Amlogic, Qualcomm,
STM32, NXP i.MX, Sophgo, TI K3, Renesas, Microchip at91, NVIDIA Tegra,
and T-HEAD.
The added Qualcomm platform support once again dominates the changes,
with seven phones and three laptops getting added in addition to many
new features on existing machines. The Snapdragon X1E support
specifically keeps improving.
The other new machines are:
- eight new machines using various 64-bit Rockchips SoCs, both on the
consumer/gaming side and developer boards
- three industrial boards with 64-bit i.MX, which is a very low
number for them.
- four more servers using a 32-bit Speed BMC
- three boards using STM32MP1 SoCs
- one new machine each using allwinner, amlogic, broadcom and renesas
chips"
* tag 'soc-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (672 commits)
arm64: dts: allwinner: h5: NanoPi NEO Plus2: Use regulators for pio
arm64: dts: mediatek: add audio support for mt8365-evk
arm64: dts: mediatek: add afe support for mt8365 SoC
arm64: dts: mediatek: mt8186-corsola: Disable DPI display interface
arm64: dts: mediatek: mt8186: Add svs node
arm64: dts: mediatek: mt8186: Add power domain for DPI
arm64: dts: mediatek: mt8195: Correct clock order for dp_intf*
arm64: dts: mt8183: add dpi node to mt8183
arm64: dts: allwinner: h5: NanoPi Neo Plus2: Fix regulators
arm64: dts: rockchip: add CAN0 and CAN1 interfaces to mecsbc board
arm64: dts: rockchip: add CAN-FD controller nodes to rk3568
arm64: dts: nuvoton: ma35d1: Add uart pinctrl settings
arm64: dts: nuvoton: ma35d1: Add pinctrl and gpio nodes
arm64: dts: nuvoton: Add syscon to the system-management node
ARM: dts: Fix undocumented LM75 compatible nodes
arm64: dts: toshiba: Fix pl011 and pl022 clocks
ARM: dts: stm32: Use SAI to generate bit and frame clock on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: Switch bitclock/frame-master to flag on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: Sort properties in audio endpoints on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: Add MECIO1 and MECT1S board variants
...
|
|
"lm75" without any vendor is undocumented. It works with the Linux
kernel since the I2C subsystem will do matches of the compatible string
without a vendor prefix to the i2c_device_id and/or driver name.
Mostly replace "lm75" with "national,lm75" as that's the original part
vendor and the compatible which matches what "lm75" matched with. In a
couple of cases the node name or compatible gives a clue to the actual
part and vendor and a more specific compatible can be used. In these
cases, it does change the variant the kernel picks.
"nct75" is an OnSemi part which is compatible with TI TMP75C based on
a comparison of the OnSemi NCT75 datasheet and configuration the Linux
driver uses. Adding an OnSemi compatible would be an ABI change.
"nxp,lm75" is most likely an NXP part. Alexander Stein says the i.MX53
boards are a NXP LM75A as well. NXP makes a LM75A and LM75B. Both are
11-bit resolution and 100ms sample time. The "national,lm75a" is
9-bit, so "national,lm75b" is the closest match for both NXP variants.
While we're here, fix the node names to use the generic name
"temperature-sensor".
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Kevin Hilman <[email protected]> # am335x-nano.dts
Signed-off-by: Rob Herring (Arm) <[email protected]>
Reviewed-by: Alexander Stein <[email protected]> # imx53-mba53.dts, imx53-tqma53.dtsi
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
The saif[01] nodes are specific to other group of the imx287
based devices, so need to be moved to different devices description file.
Leaving them here causes issues with next revision of XEA device.
Signed-off-by: Lukasz Majewski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Due to some operational problems (HW) the maximal speed of the SPI
frequency for flash memory has been reduced by half.
Signed-off-by: Lukasz Majewski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The SPI-NOR memory layout has evolved during time lifetime of the
device - for example special partitions to keep track of booted devices
for A/B booting scheme were added.
Signed-off-by: Lukasz Majewski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Bindings for other NXP pin controllers expect pin configuration nodes in
pinctrl to match certain naming, so adjust these as well, even though
their bindings are not yet in dtschema format.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Bindings for other NXP pin controllers expect pin configuration nodes in
pinctrl to match certain naming, so adjust these as well, even though
their bindings are not yet in dtschema format.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Bindings expect pin configuration nodes in pinctrl to match certain
naming:
imx6ul-kontron-bl.dtb: pinctrl@20e0000: 'usbotg1' does not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Drop an empty pin configuration node placeholder, because bindings
require 'fsl,pins' property:
imx6ul-tx6ul-0010.dtb: pinctrl@20e0000: hoggrp: 'fsl,pins' is a required property
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
According to fsl,saif.yaml, fsl,saif-master is a phandle to the master
SAIF.
Change it accordingly, to fix the following dt-schema warnings:
saif@80042000: fsl,saif-master: True is not of type 'array'
saif@80042000: Unevaluated properties are not allowed ('fsl,saif-master' was unexpected)
Signed-off-by: Fabio Estevam <[email protected]>
Acked-By: Lothar Waßmann <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The property is "fsl,pins", not "fsl,pin". Wrong property means the pin
configuration was not applied. Fixes dtbs_check warnings:
imx6ull-seeed-npi-dev-board-emmc.dtb: pinctrl@20e0000: uart1grp: 'fsl,pins' is a required property
imx6ull-seeed-npi-dev-board-emmc.dtb: pinctrl@20e0000: uart1grp: 'fsl,pin' does not match any of the regexes: 'pinctrl-[0-9]+'
Cc: [email protected]
Fixes: e3b5697195c8 ("ARM: dts: imx6ull: add seeed studio NPi dev board")
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Parthiban Nallathambi <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The property is "fsl,pins", not "fsl,pin". Wrong property means the pin
configuration was not applied. Fixes dtbs_check warnings:
imx6ul-geam.dtb: pinctrl@20e0000: tscgrp: 'fsl,pins' is a required property
imx6ul-geam.dtb: pinctrl@20e0000: tscgrp: 'fsl,pin' does not match any of the regexes: 'pinctrl-[0-9]+'
Cc: [email protected]
Fixes: a58e4e608bc8 ("ARM: dts: imx6ul-geam: Add Engicam IMX6UL GEA M6UL initial support")
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
According to simple-bus.yaml, apbh and apbx are not valid bus names.
Rename them to apbh-bus and apbx-bus to fix the following dt-schema
warnings:
'apbh@80000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
'apbx@80040000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Since the muxing is described already in imx6qdl-tqma6 can be reused
by this variant. No functional change.
Signed-off-by: Markus Niebel <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Use national,lm75a to specify exact variant used. This should cause
no functional changes.
Signed-off-by: Markus Niebel <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Use national,lm75a to specify exact variant used. This should cause
no functional changes.
While at it change node name to 'temperature-sensor@48' to
describe the function of the IC.
Signed-off-by: Markus Niebel <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Move the pinmux entries to the variant where they are actual
used. No functional changes.
Signed-off-by: Markus Niebel <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Bindings expect pin configuration nodes in pinctrl to match certain
naming and not be part of another fake node:
imx7d-sdb-sht11.dtb: pinctrl@30330000: 'imx7d-sdb' does not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Drop the "imx7d-sdb" wrapping node and adjust the names to have "grp"
prefix. Diff looks big but this should have no functional impact.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Bindings expect pin configuration nodes in pinctrl to match certain
naming:
imx7s-colibri-eval-v3.dtb: pinctrl@30330000: 'lvdstx' does not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
imx7s-warp.dtb: pinctrl@30330000: 'usdhc3grp_100mhz', 'usdhc3grp_200mhz' do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
There is no "fsl,phy" property in pin controller pincfg nodes:
imx7d-zii-rmu2.dtb: pinctrl@302c0000: enet1phyinterruptgrp: 'fsl,pins' is a required property
imx7d-zii-rmu2.dtb: pinctrl@302c0000: enet1phyinterruptgrp: 'fsl,phy' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: f496e6750083 ("ARM: dts: Add ZII support for ZII i.MX7 RMU2 board")
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The merge of imx-spdif driver into fsl-asoc-card brought
new DT properties that can be used with the "fsl,imx-audio-spdif"
compatible:
* The "spdif-controller" property from imx-spdif is named "audio-cpu"
in fsl-asoc-card.
* fsl-asoc-card uses codecs explicitly declared in DT
with "audio-codec".
With an S/PDIF, codec drivers spdif_transmitter and
spdif_receiver should be used.
Driver imx-spdif used instead the dummy codec and a pair of
boolean properties, "spdif-in" and "spdif-out".
While backward compatibility is kept to support properties
"spdif-controller", "spdif-in" and "spdif-out", using new properties has
several benefits:
* "audio-cpu" and "audio-codec" are more generic names reflecting
that the fsl-asoc-card driver supports multiple hardware.
They are properties already used by devices using the
fsl-asoc-card driver.
They are also similar to properties of simple-card: "cpu" and "codec".
* "spdif-in" and "spdif-out" imply the use of the dummy codec in the
driver. However, there are already two codec drivers for the S/PDIF,
spdif_transmitter and spdif_receiver.
It is better to declare S/PDIF Tx and Rx devices in a DT, and then
reference them with "audio-codec" than using the dummy codec.
For those reasons, this commit updates in-tree DTs to use the new
properties:
* Rename "spdif-controller" property to "audio-cpu".
* Declare S/PDIF transmitter and/or receiver devices, and use them with
the "audio-codec" property instead of "spdif-out" and/or "spdif-in".
These modifications were tested only on an imx8mn-evk board.
Note that out-of-tree and old DTs are still supported.
Signed-off-by: Elinor Montmasson <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The regulator should not be placed under simple-bus.
Remove it from simple-bus to fix the following dt-schema warnings:
'regulators' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
regulators: #size-cells:0:0: 0 is not one of [1, 2]
regulators: regulator@0:reg:0: [0] is too short
regulators: 'ranges' is a required property
Signed-off-by: Fabio Estevam <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Use national,lm75a to specify exact variant used. This should cause
no functional changes.
Signed-off-by: Markus Niebel <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Enable IIO hwmon support for ADC1 and ADC2. All channels are
available on X23 (ADC2) and X24 (ADC1) of MBa7x.
Signed-off-by: Markus Niebel <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
According to fsl,imx-dma.yaml, the node name must be dma-controller.
Change it accordingly to fix the following dt-schema warnings:
'dma@10001000' does not match '^dma-controller(@.*)?$'
Signed-off-by: Fabio Estevam <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
On the imx6dl-yapp4 revision based boards, the RGB LED is not driven
directly by the LP5562 driver but through FET transistors. Hence the LED
current is not determined by the driver but by the LED series resistors.
On the imx6dl-yapp43 revision based boards, we removed the FET transistors
to drive the LED directly from the LP5562 but forgot to tune the output
current to match the previous HW design.
Set the LED current on imx6dl-yapp43 based boards to the same values
measured on the imx6dl-yapp4 boards and limit the maximum current to 20mA.
Fixes: 7da4734751e0 ("ARM: dts: imx6dl-yapp43: Add support for new HW revision of the IOTA board")
Cc: <[email protected]>
Signed-off-by: Michal Vokáč <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
It's not necessary to split display0 node. Merge it to save two lines.
Signed-off-by: Liu Ying <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
SII9022 and TVE are connected with IPU DI0 and IPU DI1 respectively, so
they are in two different display pipelines and may run simultaneously.
Keep TVE being enabled as imx53-qsb-common.dtsi does by not setting it's
status property to "disabled".
Fixes: eeb403df953f ("ARM: dts: imx53-qsb: add support for the HDMI expander")
Signed-off-by: Liu Ying <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
By default, the ENET_REF is configured at 125MHz on i.MX6SX, which works
well for boards that operate in RGMII mode.
The imx6sx-udoo-neo has a KSZ8091 Ethernet PHY that is connected via
RMII interface, so a 50MHz ENET_REF clock is expected.
Describe the IMX6SX_CLK_ENET_REF accordingly.
Signed-off-by: Fabio Estevam <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX ARM device tree change for 6.11:
- A few changes from Krzysztof Kozlowski to fix dtschema issues
- A series from Michael Walle to improve kontron-samx6i SoM support by
fixing various errors and add kontron-samx6i-ads2 board
- Add LVDS port data mapping for M53 Menlo board
- Convert NVMEM usage to layout syntax on MBA6 boards
* tag 'imx-dt-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-kontron-samx6i: add actual device trees
ARM: dts: imx6qdl-kontron-samx6i: remove wake-up-gpio property
ARM: dts: imx6qdl-kontron-samx6i: fix PCIe reset polarity
ARM: dts: imx6qdl-kontron-samx6i: fix node names
ARM: dts: imx6qdl-kontron-samx6i: add SDIO_PWR_EN support
ARM: dts: imx6qdl-kontron-samx6i: always enable eMMC
ARM: dts: imx6qdl-kontron-samx6i: fix product name
ARM: dts: imx6qdl-kontron-samx6i: fix SPI0 chip selects
ARM: dts: imx6qdl-kontron-samx6i: cleanup the PMIC node
ARM: dts: imx6qdl-kontron-samx6i: fix board reset
ARM: dts: imx6qdl-kontron-samx6i: fix PHY reset
ARM: dts: imx6qdl-kontron-samx6i: fix phy-mode
ARM: dts: nxp: imx6: convert NVMEM content to layout syntax
ARM: dts: e60k02: fix aliases for mmc
ARM: dts: imx: Add LVDS port data mapping on M53 Menlo
ARM: dts: imx28-tx28: drop redundant 'panel-name' property
ARM: dts: imx: drop redundant 'u-boot,panel-name' property
ARM: dts: imx6dl-aristainetos2_4: drop redundant 'power-on-delay' property
ARM: dts: imx: correct choice of panel native mode
ARM: dts: imx: align panel timings node name with dtschema
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
For now, there wasn't any in-tree users of the dtsi files for the
Kontron SMARC-sAMX6i board. Let's add device trees, for this board on a
Kontron SMARC Eval 2.0 Carrier.
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Remove the "wake-up-gpio" property within the PCIe controller node.
There is no such property, thus just remove it. This will also make the
schema validation happy.
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The PCIe reset line is active low. Fix it.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Rename the nodes according to the schema. In particular, rename the bit
bang I2C controller to "i2c-N" and the mux nodes of the audmux to
"mux-*". While at it, fix the typo "adu", which should have been "aud".
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The module can enable/disable the SD card power supply and has
it's dedicated pin SDIO_PWR_EN for that reason. This is esp.
useful to be able to reset the SD card if it was in an UHS mode.
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
There are no variants of this module without an eMMC.
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The correct name of the product is "Kontron SMARC-sAMX6i". See also
https://www.kontron.com/en/products/smarc-samx6i/p89810
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Remove the comment, remove the unused phandle name for the
VGEN5 output. VGEN5 is not used at all.
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The i.MX6 cannot add any RGMII delays. The PHY has to add both the RX
and TX delays on the RGMII interface. Fix the interface mode. While at
it, use the new phy-connection-type property name.
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Use cleaner (and non-deprecated) bindings syntax. See commit
bd912c991d2e ("dt-bindings: nvmem: layouts: add fixed-layout") for
details.
Signed-off-by: Rafał Miłecki <[email protected]>
Reviewed-by: Alexander Stein <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Since commit fa2d0aa96941
("mmc: core: Allow setting slot index via device tree alias")
mmc numbering are changed, confusing boot scripts. Fix that by adding
proper aliases
Signed-off-by: Andreas Kemnade <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Describe LVDS data mapping of the LVDS-to-DPI decoder input port.
This fixes a warning reported by lvds-codec driver:
"
lvds-codec lvds-decoder: missing 'data-mapping' DT property
"
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
We cannot use /delete-node/ directive to delete a node in a DT
overlay. The node won't be deleted effectively. Instead, set
the node's status property to "disabled" to achieve something
similar.
Fixes: eeb403df953f ("ARM: dts: imx53-qsb: add support for the HDMI expander")
Signed-off-by: Liu Ying <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Panel timing bindings do not allow 'panel-name' and there seems to be no
users of it: neither Linux kernel drivers, nor U-boot as of
v2024.07-rc2.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Panel timing bindings do not allow 'u-boot,panel-name' and there seems
to be no users of it: neither Linux kernel drivers, nor U-boot as of
v2024.07-rc2. Reported by dtbs_check:
imx6qp-tx6qp-8037.dtb: display-timings: timing-et0700: 'u-boot,panel-name' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
LG4573 panel bindings do not allow 'power-on-delay' property. Linux
driver does not use it, either. Reported by dtbs_check:
imx6dl-aristainetos2_4.dtb: display@0: Unevaluated properties are not allowed ('power-on-delay' was unexpected)
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Bindings and Linux driver expect native-mode to be a phandle to one of
the timings node, not a boolean property. Correct the DTS to fix
dtbs_check warnings like:
imx53-m53evk.dtb: display-timings: timing-800x480p60: 'native-mode' does not match any of the regexes: 'pinctrl-[0-9]+'
This should not have actual effect for Linux kernel (no real bug
affecting choice of native-mode), because the first timing node is
chosen in absence of proper native-mode property.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|