| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
After running once, the for_each_trip_desc() loop in
bang_bang_manage() is pure needless overhead because it is not going to
make any changes unless a new cooling device has been bound to one of
the trips in the thermal zone or the system is resuming from sleep.
For this reason, make bang_bang_manage() set governor_data for the
thermal zone and check it upfront to decide whether or not it needs to
do anything.
However, governor_data needs to be reset in some cases to let
bang_bang_manage() know that it should walk the trips again, so add an
.update_tz() callback to the governor and make the core additionally
invoke it during system resume.
To avoid affecting the other users of that callback unnecessarily, add
a special notification reason for system resume, THERMAL_TZ_RESUME, and
also pass it to __thermal_zone_device_update() called during system
resume for consistency.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Peter Kästle <[email protected]>
Reviewed-by: Zhang Rui <[email protected]>
Cc: 6.10+ <[email protected]> # 6.10+
Link: https://patch.msgid.link/[email protected]
|
|
After recent changes, the Bang-bang governor may not adjust the
initial configuration of cooling devices to the actual situation.
Namely, if a cooling device bound to a certain trip point starts in
the "on" state and the thermal zone temperature is below the threshold
of that trip point, the trip point may never be crossed on the way up
in which case the state of the cooling device will never be adjusted
because the thermal core will never invoke the governor's
.trip_crossed() callback. [Note that there is no issue if the zone
temperature is at the trip threshold or above it to start with because
.trip_crossed() will be invoked then to indicate the start of thermal
mitigation for the given trip.]
To address this, add a .manage() callback to the Bang-bang governor
and use it to ensure that all of the thermal instances managed by the
governor have been initialized properly and the states of all of the
cooling devices involved have been adjusted to the current zone
temperature as appropriate.
Fixes: 530c932bdf75 ("thermal: gov_bang_bang: Use .trip_crossed() instead of .throttle()")
Link: https://lore.kernel.org/linux-pm/[email protected]/
Cc: 6.10+ <[email protected]> # 6.10+
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Peter Kästle <[email protected]>
Reviewed-by: Zhang Rui <[email protected]>
Link: https://patch.msgid.link/[email protected]
|
|
Move the setting of the thermal instance target state from
bang_bang_control() into a separate function that will be also called
in a different place going forward.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Peter Kästle <[email protected]>
Reviewed-by: Zhang Rui <[email protected]>
Cc: 6.10+ <[email protected]> # 6.10+
Link: https://patch.msgid.link/[email protected]
|
|
Instead of clearing the "updated" flag for each cooling device
affected by the trip point crossing in bang_bang_control() and
walking all thermal instances to run thermal_cdev_update() for all
of the affected cooling devices, call __thermal_cdev_update()
directly for each of them.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Peter Kästle <[email protected]>
Reviewed-by: Zhang Rui <[email protected]>
Cc: 6.10+ <[email protected]> # 6.10+
Link: https://patch.msgid.link/[email protected]
|
|
Commit 391208485c3a ("arm64/sve: Remove SMCR pseudo register from cpufeature code")
removed the implementation but leave declaration.
Signed-off-by: Yue Haibing <[email protected]>
Reviewed-by: Mark Brown <[email protected]>
Reviewed-by: Zenghui Yu <[email protected]>
Reviewed-by: Anshuman Khandual <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
IORT(Input Output Remapping Table) represents the I/O topology of an
Arm-based system for use with the ACPI, so acpi_iort.h is for arm64
only.
This helps git-send-email to figure out the proper maintainers when
touching the file.
Signed-off-by: Hanjun Guo <[email protected]>
Acked-by: Sudeep Holla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
Let the kememdup_array() take care about multiplication and possible
overflows.
Signed-off-by: Andy Shevchenko <[email protected]>
Acked-by: Hanjun Guo <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
Commit bf4b558eba92 ("arm64: add early_ioremap support") removed the
implementation but leave declaration.
Signed-off-by: Yue Haibing <[email protected]>
Reviewed-by: Anshuman Khandual <[email protected]>
Acked-by: Catalin Marinas <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
These functions is never implemented and used.
Signed-off-by: Yue Haibing <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
A minor anti-pattern has established itself in __init_el2_fgt,
where each block of instructions is skipped by jumping to a label
named for the next (typically unrelated) block.
This makes diffs more noisy than necessary, since appending each
new block to deal with some new architecture feature now requires
altering a branch destination in the existing code.
Fix it by naming the affected labels based on the block that is
skipping itself instead, as is done elsewhere in the el2_setup code.
No functional change.
Signed-off-by: Dave Martin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
A few SME-related sigcontext UAPI macros leave an argument
unprotected from misparsing during macro expansion.
Add parentheses around references to macro arguments where
appropriate.
Signed-off-by: Dave Martin <[email protected]>
Fixes: ee072cf70804 ("arm64/sme: Implement signal handling for ZT")
Fixes: 39782210eb7e ("arm64/sme: Implement ZA signal handling")
Reviewed-by: Mark Brown <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
Earlier TCR_SMP_FLAGS gets conditionally set as TCR_SHARED with CONFIG_SMP.
Currently CONFIG_SMP is always enabled on arm64 platforms, hence drop this
indirection via TCR_SMP_FLAGS and instead always directly use TCR_SHARED.
Cc: Catalin Marinas <[email protected]>
Cc: Will Deacon <[email protected]>
Cc: Ryan Roberts <[email protected]>
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Anshuman Khandual <[email protected]>
Reviewed-by: Ryan Roberts <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
This just drops off the macro PMD_SECT_VALID which remains unused. Because
macro PMD_TYPE_SECT with same value (_AT(pmdval_t, 1) << 0), gets used for
creating or updating given block mappings.
Cc: Catalin Marinas <[email protected]>
Cc: Will Deacon <[email protected]>
Cc: Ryan Roberts <[email protected]>
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Anshuman Khandual <[email protected]>
Reviewed-by: Ryan Roberts <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
Syzbot points out that skb_trim() has a sanity check on the existing length of
the skb, which can be uninitialised in some error paths. The intent here is
clearly just to reset the length to zero before resubmitting, so switch to
calling __skb_set_length(skb, 0) directly. In addition, __skb_set_length()
already contains a call to skb_reset_tail_pointer(), so remove the redundant
call.
The syzbot report came from ath9k_hif_usb_reg_in_cb(), but there's a similar
usage of skb_trim() in ath9k_hif_usb_rx_cb(), change both while we're at it.
Reported-by: [email protected]
Signed-off-by: Toke Høiland-Jørgensen <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://patch.msgid.link/[email protected]
|
|
With host_mlme support being added mwifiex_cfg80211_ops is no longer
constant, but supplemented with the host_mlme related ops when host_mlme
support is enabled. This doesn't work with multiple adapters when only
few of then have host_mlme support. Duplicate mwifiex_cfg80211_ops
before using it and keep the original constant.
While at it mark mwifiex_cfg80211_ops const to prevent people from
changing it again during runtime.
Fixes: 36995892c271c ("wifi: mwifiex: add host mlme for client mode")
Signed-off-by: Sascha Hauer <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
Acked-by: Brian Norris <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://patch.msgid.link/20240809-mwifiex-duplicate-mwifiex_cfg80211_ops-v1-1-23e0e6290ace@pengutronix.de
|
|
mwifiex_band_2ghz and mwifiex_band_5ghz are statically allocated, but
used and modified in driver instances. Duplicate them before using
them in driver instances so that different driver instances do not
influence each other.
This was observed on a board which has one PCIe and one SDIO mwifiex
adapter. It blew up in mwifiex_setup_ht_caps(). This was called with
the statically allocated struct which is modified in this function.
Cc: [email protected]
Fixes: d6bffe8bb520 ("mwifiex: support for creation of AP interface")
Signed-off-by: Sascha Hauer <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
Acked-by: Brian Norris <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
Link: https://patch.msgid.link/20240809-mwifiex-duplicate-static-structs-v1-1-6837b903b1a4@pengutronix.de
|
|
A few protocol versions had been increased with SCMI v3.2.
Update accordingly the supported version define in the kernel stack,
since all the mandatory base commands are indeed already supported.
Signed-off-by: Cristian Marussi <[email protected]>
Message-Id: <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
|
|
Since all SCMI transports have been made standalone drivers, remove all the
core SCMI stack legacy support that was needed to run transports as built
into the stack.
Signed-off-by: Cristian Marussi <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
|
|
Make SCMI VirtIO transport a standalone driver that can be optionally
loaded as a module.
CC: Michael S. Tsirkin <[email protected]>
CC: Igor Skalkin <[email protected]>
CC: Peter Hilber <[email protected]>
Signed-off-by: Cristian Marussi <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
|
|
Make SCMI OPTEE transport a standalone driver that can be optionally
loaded as a module.
CC: Etienne Carriere <[email protected]>
Signed-off-by: Cristian Marussi <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>
|
|
Make SCMI SMC transport a standalone driver that can be optionally
loaded as a module.
CC: Peng Fan <[email protected]>
CC: Nikunj Kela <[email protected]>
Signed-off-by: Cristian Marussi <[email protected]>
Message-Id: <[email protected]>
[sudeep.holla: moved Clang Thumb2 build fix to the new makefile]
Signed-off-by: Sudeep Holla <[email protected]>
|
|
Use the mem_is_zero() helper where possible.
Conversion done using cocci:
| @@
| expression PTR;
| expression SIZE;
| @@
|
| <...
| (
| - memchr_inv(PTR, 0, SIZE) == NULL
| + mem_is_zero(PTR, SIZE)
| |
| - !memchr_inv(PTR, 0, SIZE)
| + mem_is_zero(PTR, SIZE)
| |
| - memchr_inv(PTR, 0, SIZE)
| + !mem_is_zero(PTR, SIZE)
| )
| ...>
Reviewed-by: Kees Cook <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Almost two thirds of the memchr_inv() usages check if the memory area is
all zeros, with no interest in where in the buffer the first non-zero
byte is located. Checking for !memchr_inv(s, 0, n) is also not very
intuitive or discoverable. Add an explicit mem_is_zero() helper for this
use case.
Reviewed-by: Kees Cook <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Vladimir Oltean says:
====================
VLAN fixes for Ocelot driver
This is a collection of patches I've gathered over the past several
months.
Patches 1-6/14 are supporting patches for selftests.
Patch 9/14 fixes PTP TX from a VLAN upper of a VLAN-aware bridge port
when using the "ocelot-8021q" tagging protocol. Patch 7/14 is its
supporting selftest.
Patch 10/14 fixes the QoS class used by PTP in the same case as above.
It is hard to quantify - there is no selftest.
Patch 11/14 fixes potential data corruption during PTP TX in the same
case as above. Again, there is no selftest.
Patch 13/14 fixes RX in the same case as above - 8021q upper of a
VLAN-aware bridge port, with the "ocelot-8021q" tagging protocol. Patch
12/14 is a supporting patch for this in the DSA core, and 7/14 is also
its selftest.
Patch 14/14 ensures that VLAN-aware bridges offloaded to Ocelot only
react to the ETH_P_8021Q TPID, and treat absolutely everything else as
VLAN-untagged, including ETH_P_8021AD. Patch 8/14 is the supporting
selftest.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
I was revisiting the topic of 802.1ad treatment in the Ocelot switch [0]
and realized that not only is its basic VLAN classification pipeline
improper for offloading vlan_protocol 802.1ad bridges, but also improper
for offloading regular 802.1Q bridges already.
Namely, 802.1ad-tagged traffic should be treated as VLAN-untagged by
bridged ports, but this switch treats it as if it was 802.1Q-tagged with
the same VID as in the 802.1ad header. This is markedly different to
what the Linux bridge expects; see the "other_tpid()" function in
tools/testing/selftests/net/forwarding/bridge_vlan_aware.sh.
An idea came to me that the VCAP IS1 TCAM is more powerful than I'm
giving it credit for, and that it actually overwrites the classified VID
before the VLAN Table lookup takes place. In other words, it can be
used even to save a packet from being dropped on ingress due to VLAN
membership.
Add a sophisticated TCAM rule hardcoded into the driver to force the
switch to behave like a Linux bridge with vlan_filtering 1 vlan_protocol
802.1Q.
Regarding the lifetime of the filter: eventually the bridge will
disappear, and vlan_filtering on the port will be restored to 0 for
standalone mode. Then the filter will be deleted.
[0]: https://lore.kernel.org/netdev/20201009122947.nvhye4hvcha3tljh@skbuf/
Fixes: 7142529f1688 ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There is a major design bug with ocelot-8021q, which is that it expects
more of the hardware than the hardware can actually do. The short
summary of the issue is that when a port is under a VLAN-aware bridge
and we use this tagging protocol, VLAN upper interfaces of this port do
not see RX traffic.
We use VCAP ES0 (egress rewriter) rules towards the tag_8021q CPU port
to encapsulate packets with an outer tag, later stripped by software,
that depends on the source user port. We do this so that packets can be
identified in ocelot_rcv(). To be precise, we create rules with
push_outer_tag = OCELOT_ES0_TAG and push_inner_tag = 0.
With this configuration, we expect the switch to keep the inner tag
configuration as found in the packet (if it was untagged on user port
ingress, keep it untagged, otherwise preserve the VLAN tag unmodified
as the inner tag towards the tag_8021q CPU port). But this is not what
happens.
Instead, table "Tagging Combinations" from the user manual suggests
that when the ES0 action is "PUSH_OUTER_TAG=1 and PUSH_INNER_TAG=0",
there will be "no inner tag". Experimentation further clarifies what
this means.
It appears that this "inner tag" which is not pushed into the packet on
its egress towards the CPU is none other than the classified VLAN.
When the ingress user port is standalone or under a VLAN-unaware bridge,
the classified VLAN is a discardable quantity: it is a fixed value - the
result of ocelot_vlan_unaware_pvid()'s configuration, and actually
independent of the VID from any 802.1Q header that may be in the frame.
It is actually preferable to discard the "inner tag" in this case.
The problem is when the ingress port is under a VLAN-aware bridge.
Then, the classified VLAN is taken from the frame's 802.1Q header, with
a fallback on the bridge port's PVID. It would be very good to not
discard the "inner tag" here, because if we do, we break communication
with any 8021q VLAN uppers that the port might have. These have a
processing path outside the bridge.
There seems to be nothing else we can do except to change the
configuration for VCAP ES0 rules, to actually push the inner VLAN into
the frame. There are 2 options for that, first is to push a fixed value
specified in the rule, and second is to push a fixed value, plus
(aka arithmetic +) the classified VLAN. We choose the second option,
and we select that fixed value as 0. Thus, what is pushed in the inner
tag is just the classified VLAN.
From there, we need to perform software untagging, in the receive path,
of stuff that was untagged on the wire.
Fixes: 7c83a7c539ab ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Through code analysis, I realized that the ds->untag_bridge_pvid logic
is contradictory - see the newly added FIXME above the kernel-doc for
dsa_software_untag_vlan_unaware_bridge().
Moreover, for the Felix driver, I need something very similar, but which
is actually _not_ contradictory: untag the bridge PVID on RX, but for
VLAN-aware bridges. The existing logic does it for VLAN-unaware bridges.
Since I don't want to change the functionality of drivers which were
supposedly properly tested with the ds->untag_bridge_pvid flag, I have
introduced a new one: ds->untag_vlan_aware_bridge_pvid, and I have
refactored the DSA reception code into a common path for both flags.
TODO: both flags should be unified under a single ds->software_vlan_untag,
which users of both current flags should set. This is not something that
can be carried out right away. It needs very careful examination of all
drivers which make use of this functionality, since some of them
actually get this wrong in the first place.
For example, commit 9130c2d30c17 ("net: dsa: microchip: ksz8795: Use
software untagging on CPU port") uses this in a driver which has
ds->configure_vlan_while_not_filtering = true. The latter mechanism has
been known for many years to be broken by design:
https://lore.kernel.org/netdev/CABumfLzJmXDN_W-8Z=p9KyKUVi_HhS7o_poBkeKHS2BkAiyYpw@mail.gmail.com/
and we have the situation of 2 bugs canceling each other. There is no
private VLAN, and the port follows the PVID of the VLAN-unaware bridge.
So, it's kinda ok for that driver to use the ds->untag_bridge_pvid
mechanism, in a broken way.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
As explained by Horatiu Vultur in commit 603ead96582d ("net: sparx5: Add
spinlock for frame transmission from CPU") which is for a similar
hardware design, multiple CPUs can simultaneously perform injection
or extraction. There are only 2 register groups for injection and 2
for extraction, and the driver only uses one of each. So we'd better
serialize access using spin locks, otherwise frame corruption is
possible.
Note that unlike in sparx5, FDMA in ocelot does not have this issue
because struct ocelot_fdma_tx_ring already contains an xmit_lock.
I guess this is mostly a problem for NXP LS1028A, as that is dual core.
I don't think VSC7514 is. So I'm blaming the commit where LS1028A (aka
the felix DSA driver) started using register-based packet injection and
extraction.
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There are 2 distinct code paths (listed below) in the source code which
set up an injection header for Ocelot(-like) switches. Code path (2)
lacks the QoS class and source port being set correctly. Especially the
improper QoS classification is a problem for the "ocelot-8021q"
alternative DSA tagging protocol, because we support tc-taprio and each
packet needs to be scheduled precisely through its time slot. This
includes PTP, which is normally assigned to a traffic class other than
0, but would be sent through TC 0 nonetheless.
The code paths are:
(1) ocelot_xmit_common() from net/dsa/tag_ocelot.c - called only by the
standard "ocelot" DSA tagging protocol which uses NPI-based
injection - sets up bit fields in the tag manually to account for
a small difference (destination port offset) between Ocelot and
Seville. Namely, ocelot_ifh_set_dest() is omitted out of
ocelot_xmit_common(), because there's also seville_ifh_set_dest().
(2) ocelot_ifh_set_basic(), called by:
- ocelot_fdma_prepare_skb() for FDMA transmission of the ocelot
switchdev driver
- ocelot_port_xmit() -> ocelot_port_inject_frame() for
register-based transmission of the ocelot switchdev driver
- felix_port_deferred_xmit() -> ocelot_port_inject_frame() for the
DSA tagger ocelot-8021q when it must transmit PTP frames (also
through register-based injection).
sets the bit fields according to its own logic.
The problem is that (2) doesn't call ocelot_ifh_set_qos_class().
Copying that logic from ocelot_xmit_common() fixes that.
Unfortunately, although desirable, it is not easily possible to
de-duplicate code paths (1) and (2), and make net/dsa/tag_ocelot.c
directly call ocelot_ifh_set_basic()), because of the ocelot/seville
difference. This is the "minimal" fix with some logic duplicated (but
at least more consolidated).
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
register injection
Problem description
-------------------
On an NXP LS1028A (felix DSA driver) with the following configuration:
- ocelot-8021q tagging protocol
- VLAN-aware bridge (with STP) spanning at least swp0 and swp1
- 8021q VLAN upper interfaces on swp0 and swp1: swp0.700, swp1.700
- ptp4l on swp0.700 and swp1.700
we see that the ptp4l instances do not see each other's traffic,
and they all go to the grand master state due to the
ANNOUNCE_RECEIPT_TIMEOUT_EXPIRES condition.
Jumping to the conclusion for the impatient
-------------------------------------------
There is a zero-day bug in the ocelot switchdev driver in the way it
handles VLAN-tagged packet injection. The correct logic already exists in
the source code, in function ocelot_xmit_get_vlan_info() added by commit
5ca721c54d86 ("net: dsa: tag_ocelot: set the classified VLAN during xmit").
But it is used only for normal NPI-based injection with the DSA "ocelot"
tagging protocol. The other injection code paths (register-based and
FDMA-based) roll their own wrong logic. This affects and was noticed on
the DSA "ocelot-8021q" protocol because it uses register-based injection.
By moving ocelot_xmit_get_vlan_info() to a place that's common for both
the DSA tagger and the ocelot switch library, it can also be called from
ocelot_port_inject_frame() in ocelot.c.
We need to touch the lines with ocelot_ifh_port_set()'s prototype
anyway, so let's rename it to something clearer regarding what it does,
and add a kernel-doc. ocelot_ifh_set_basic() should do.
Investigation notes
-------------------
Debugging reveals that PTP event (aka those carrying timestamps, like
Sync) frames injected into swp0.700 (but also swp1.700) hit the wire
with two VLAN tags:
00000000: 01 1b 19 00 00 00 00 01 02 03 04 05 81 00 02 bc
~~~~~~~~~~~
00000010: 81 00 02 bc 88 f7 00 12 00 2c 00 00 02 00 00 00
~~~~~~~~~~~
00000020: 00 00 00 00 00 00 00 00 00 00 00 01 02 ff fe 03
00000030: 04 05 00 01 00 04 00 00 00 00 00 00 00 00 00 00
00000040: 00 00
The second (unexpected) VLAN tag makes felix_check_xtr_pkt() ->
ptp_classify_raw() fail to see these as PTP packets at the link
partner's receiving end, and return PTP_CLASS_NONE (because the BPF
classifier is not written to expect 2 VLAN tags).
The reason why packets have 2 VLAN tags is because the transmission
code treats VLAN incorrectly.
Neither ocelot switchdev, nor felix DSA, declare the NETIF_F_HW_VLAN_CTAG_TX
feature. Therefore, at xmit time, all VLANs should be in the skb head,
and none should be in the hwaccel area. This is done by:
static struct sk_buff *validate_xmit_vlan(struct sk_buff *skb,
netdev_features_t features)
{
if (skb_vlan_tag_present(skb) &&
!vlan_hw_offload_capable(features, skb->vlan_proto))
skb = __vlan_hwaccel_push_inside(skb);
return skb;
}
But ocelot_port_inject_frame() handles things incorrectly:
ocelot_ifh_port_set(ifh, port, rew_op, skb_vlan_tag_get(skb));
void ocelot_ifh_port_set(struct sk_buff *skb, void *ifh, int port, u32 rew_op)
{
(...)
if (vlan_tag)
ocelot_ifh_set_vlan_tci(ifh, vlan_tag);
(...)
}
The way __vlan_hwaccel_push_inside() pushes the tag inside the skb head
is by calling:
static inline void __vlan_hwaccel_clear_tag(struct sk_buff *skb)
{
skb->vlan_present = 0;
}
which does _not_ zero out skb->vlan_tci as seen by skb_vlan_tag_get().
This means that ocelot, when it calls skb_vlan_tag_get(), sees
(and uses) a residual skb->vlan_tci, while the same VLAN tag is
_already_ in the skb head.
The trivial fix for double VLAN headers is to replace the content of
ocelot_ifh_port_set() with:
if (skb_vlan_tag_present(skb))
ocelot_ifh_set_vlan_tci(ifh, skb_vlan_tag_get(skb));
but this would not be correct either, because, as mentioned,
vlan_hw_offload_capable() is false for us, so we'd be inserting dead
code and we'd always transmit packets with VID=0 in the injection frame
header.
I can't actually test the ocelot switchdev driver and rely exclusively
on code inspection, but I don't think traffic from 8021q uppers has ever
been injected properly, and not double-tagged. Thus I'm blaming the
introduction of VLAN fields in the injection header - early driver code.
As hinted at in the early conclusion, what we _want_ to happen for
VLAN transmission was already described once in commit 5ca721c54d86
("net: dsa: tag_ocelot: set the classified VLAN during xmit").
ocelot_xmit_get_vlan_info() intends to ensure that if the port through
which we're transmitting is under a VLAN-aware bridge, the outer VLAN
tag from the skb head is stripped from there and inserted into the
injection frame header (so that the packet is processed in hardware
through that actual VLAN). And in all other cases, the packet is sent
with VID=0 in the injection frame header, since the port is VLAN-unaware
and has logic to strip this VID on egress (making it invisible to the
wire).
Fixes: 08d02364b12f ("net: mscc: fix the injection header")
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The bridge VLAN implementation w.r.t. VLAN protocol is described in
merge commit 1a0b20b25732 ("Merge branch 'bridge-next'"). We are only
sensitive to those VLAN tags whose TPID is equal to the bridge's
vlan_protocol. Thus, an 802.1ad VLAN should be treated as 802.1Q-untagged.
Add 3 tests which validate that:
- 802.1ad-tagged traffic is learned into the PVID of an 802.1Q-aware
bridge
- Double-tagged traffic is forwarded when just the PVID of the port is
present in the VLAN group of the ports
- Double-tagged traffic is not forwarded when the PVID of the port is
absent from the VLAN group of the ports
The test passes with both veth and ocelot.
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Ido Schimmel <[email protected]>
Tested-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
A breakage in the felix DSA driver shows we do not have enough test
coverage. More generally, it is sufficiently special that it is likely
drivers will treat it differently.
This is not meant to be a full PTP test, it just makes sure that PTP
packets sent to the different addresses corresponding to their profiles
are received correctly. The local_termination selftest seemed like the
most appropriate place for this addition.
PTP RX/TX in some cases makes no sense (over a bridge) and this is why
$skip_ptp exists. And in others - PTP over a bridge port - the IP stack
needs convincing through the available bridge netfilter hooks to leave
the PTP packets alone and not stolen by the bridge rx_handler. It is
safe to assume that users have that figured out already. This is a
driver level test, and by using tcpdump, all that extra setup is out of
scope here.
send_non_ip() was an unfinished idea; written but never used.
Replace it with a more generic send_raw(), and send 3 PTP packet types
times 3 transports.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
xfail_on_veth() for this test is an incorrect approximation which gives
false positives and false negatives.
When local_termination fails with "reception succeeded, but should have failed",
it is because the DUT ($h2) accepts packets even when not configured as
promiscuous. This is not something specific to veth; even the bridge
behaves that way, but this is not captured by the xfail_on_veth test.
The IFF_UNICAST_FLT flag is not explicitly exported to user space, but
it can somewhat be determined from the interface's behavior. We have to
create a macvlan upper with a different MAC address. This forces a
dev_uc_add() call in the kernel. When the unicast filtering list is
not empty, but the device doesn't support IFF_UNICAST_FLT,
__dev_set_rx_mode() force-enables promiscuity on the interface, to
ensure correct behavior (that the requested address is received).
We can monitor the change in the promiscuity flag and infer from it
whether the device supports unicast filtering.
There is no equivalent thing for allmulti, unfortunately. We never know
what's hiding behind a device which has allmulti=off. Whether it will
actually perform RX multicast filtering of unknown traffic is a strong
"maybe". The bridge driver, for example, completely ignores the flag.
We'll have to keep the xfail behavior, but instead of XFAIL on just
veth, always XFAIL.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
behavior
Add more coverage to the local termination selftest as follows:
- 8021q upper of $h2
- 8021q upper of $h2, where $h2 is a port of a VLAN-unaware bridge
- 8021q upper of $h2, where $h2 is a port of a VLAN-aware bridge
- 8021q upper of VLAN-unaware br0, which is the upper of $h2
- 8021q upper of VLAN-aware br0, which is the upper of $h2
Especially the cases with traffic sent through the VLAN upper of a
VLAN-aware bridge port will be immediately relevant when we will start
transmitting PTP packets as an additional kind of traffic.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The current bridge() test is for packet reception on a VLAN-unaware
bridge. Some things are different enough with VLAN-aware bridges that
it's worth renaming this test into vlan_unaware_bridge(), and add a new
vlan_aware_bridge() test.
The two will share the same implementation: bridge() becomes a common
function, which receives $vlan_filtering as an argument. Rename it to
test_bridge() at the same time, because just bridge() pollutes the
global namespace and we cannot invoke the binary with the same name from
the iproute2 package currently.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There are upcoming tests which verify the RX filtering of a bridge
(or bridge port), but under differing vlan_filtering conditions.
Since we currently print $h2 (the DUT) in the log_test() output, it
becomes necessary to make a further distinction between tests, to not
give the user the impression that the exact same thing is run twice.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In future changes we will want to subject the DUT, $h2, to additional
VLAN-tagged traffic. For that, we need to run the tests using $h1.100 as
a sending interface, rather than the currently hardcoded $h1.
Add a parameter to run_test() and modify its 2 callers to explicitly
pass $h1, as was implicit before.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This will be used in other subtests as well; make new macvlan_create()
and macvlan_destroy() functions.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The function isn't used outside of intel_display_power.c. Make it
static.
Suggested-by: Imre Deak <[email protected]>
Reviewed-by: Imre Deak <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Going forward, struct intel_display shall replace struct
drm_i915_private as the main display device data pointer type. Convert
intel_hti.[ch] to struct intel_display.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Going forward, struct intel_display shall replace struct
drm_i915_private as the main display device data pointer type. Convert
intel_dp_aux_backlight.[ch] to struct intel_display.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Going forward, struct intel_display shall replace struct
drm_i915_private as the main display device data pointer type. Convert
intel_lspcon.[ch] to struct intel_display.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Going forward, struct intel_display shall replace struct
drm_i915_private as the main display device data pointer type. Convert
intel_alpm.[ch] to struct intel_display.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Going forward, struct intel_display shall replace struct
drm_i915_private as the main display device data pointer type. Convert
intel_load_detect.[ch] to struct intel_display.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Going forward, struct intel_display shall replace struct
drm_i915_private as the main display device data pointer type. Convert
intel_link_bw.[ch] to struct intel_display.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Add support for converting struct intel_atomic_state pointers to struct
intel_display pointers.
Reviewed-by: Rodrigo Vivi <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
Ensure, as the driver probes the device, that all endpoints that the
driver may attempt to access exist and are of the correct type.
All XillyUSB devices must have a Bulk IN and Bulk OUT endpoint at
address 1. This is verified in xillyusb_setup_base_eps().
On top of that, a XillyUSB device may have additional Bulk OUT
endpoints. The information about these endpoints' addresses is deduced
from a data structure (the IDT) that the driver fetches from the device
while probing it. These endpoints are checked in setup_channels().
A XillyUSB device never has more than one IN endpoint, as all data
towards the host is multiplexed in this single Bulk IN endpoint. This is
why setup_channels() only checks OUT endpoints.
Reported-by: [email protected]
Cc: stable <[email protected]>
Closes: https://lore.kernel.org/all/[email protected]/T/
Fixes: a53d1202aef1 ("char: xillybus: Add driver for XillyUSB (Xillybus variant for USB)").
Signed-off-by: Eli Billauer <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
As the wakeup work item now runs on a separate workqueue, it needs to be
flushed separately along with flushing the device's workqueue.
Also, move the destroy_workqueue() call to the end of the exit method,
so that deinitialization is done in the opposite order of
initialization.
Fixes: ccbde4b128ef ("char: xillybus: Don't destroy workqueue from work item running on it")
Cc: stable <[email protected]>
Signed-off-by: Eli Billauer <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
for_each_child_of_node can help to iterate through the device_node,
and we don't need to use while loop. No functional change with this
conversion.
Signed-off-by: Zhang Zekun <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Replace FB_BLANK_ constants with their counterparts from the
backlight subsystem. The values are identical, so there's no
change in functionality or semantics.
Signed-off-by: Thomas Zimmermann <[email protected]>
Cc: Jyri Sarha <[email protected]>
Cc: Tomi Valkeinen <[email protected]>
Reviewed-by: Tomi Valkeinen <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|