aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2021-03-30arm64: dts: intel: socfpga_agilex: move timer out of soc nodeKrzysztof Kozlowski1-9/+9
The ARM architected timer is part of ARM CPU design therefore by convention it should not be inside the soc node. This also fixes dtc warning like: arch/arm64/boot/dts/intel/socfpga_agilex.dtsi:410.9-416.5: Warning (simple_bus_reg): /soc/timer: missing or empty reg/ranges property Signed-off-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Dinh Nguyen <[email protected]>
2021-03-30arm64: dts: intel: socfpga_agilex: move clocks out of soc nodeKrzysztof Kozlowski1-28/+28
The clocks are usually not part of the SoC but provided on the board (external oscillators). Moving them out of soc node fixes dtc warning: arch/arm64/boot/dts/intel/socfpga_agilex.dtsi:111.10-137.5: Warning (simple_bus_reg): /soc/clocks: missing or empty reg/ranges property Signed-off-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Dinh Nguyen <[email protected]>
2021-03-30arm64: dts: intel: socfpga: override clocks by labelKrzysztof Kozlowski3-24/+12
Using full paths to extend or override a device tree node is error prone. If there was a typo error, a new node will be created instead of extending the existing node. This will lead to run-time errors that could be hard to detect. A mistyped label on the other hand, will cause a dtc compile error (during build time). Signed-off-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Dinh Nguyen <[email protected]>
2021-03-30arm: mediatek: dts: activate SMP for mt6589Boris Lysov1-0/+1
This simple patch activates SMP for mt6589 by adding the missing "enable-method" property. After applying this patch kernel log indicates all cores are brought up: [ 0.070122] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.071652] Setting up static identity map for 0x80100000 - 0x80100054 [ 0.072711] rcu: Hierarchical SRCU implementation. [ 0.073853] smp: Bringing up secondary CPUs ... [ 0.133675] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.193675] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.253675] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.253818] smp: Brought up 1 node, 4 CPUs [ 0.256930] SMP: Total of 4 processors activated (7982.28 BogoMIPS). [ 0.257855] CPU: All CPU(s) started in SVC mode. Before this change CPU cores 1-3 didn't start and the following lines were in kernel log: [ 0.070126] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.071640] Setting up static identity map for 0x80100000 - 0x80100054 [ 0.072706] rcu: Hierarchical SRCU implementation. [ 0.073850] smp: Bringing up secondary CPUs ... [ 0.076052] smp: Brought up 1 node, 1 CPU [ 0.076678] SMP: Total of 1 processors activated (2000.48 BogoMIPS). [ 0.077603] CPU: All CPU(s) started in SVC mode. Signed-off-by: Boris Lysov <[email protected]> Link: https://lore.kernel.org/r/20210314023735.052d2d35@pc Signed-off-by: Matthias Brugger <[email protected]>
2021-03-30dt-bindings: arm64: dts: mediatek: Add mt8516-pumpkin boardFabien Parent1-0/+4
Add binding documentation for the MT8516 Pumpkin board. Signed-off-by: Fabien Parent <[email protected]> Acked-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-30arm64: dts: mt7622: add ePA/eLNA pinmux for built-in WiFiRyder Lee1-0/+12
This just illustrates one of possible combinations. User should setup the corresponding pins according to the onboard RF data that stores in eeprom. Signed-off-by: Ryder Lee <[email protected]> Link: https://lore.kernel.org/r/641c5e40f54e7c9c8eaa6be398d7169445b6fede.1617006498.git.ryder.lee@mediatek.com Signed-off-by: Matthias Brugger <[email protected]>
2021-03-30ARM: dts: ux500: Add Cypress CTTYSP touch to TVK UIBLinus Walleij1-0/+46
The TVK1281618 R3 UIB has a Cypress CTTYSP touchscreen. Add it to the device tree file. Signed-off-by: Linus Walleij <[email protected]>
2021-03-30ARM: dts: ux500: Bump AUX1 voltageLinus Walleij1-2/+2
The voltage default on the AB8500 VAUX1 regulator is way too low and does not correspond to the setting in the vendor tree. This should be 2.8-3.3 V not 2.5-2.9 V or things like the HREFP520 touchscreen will not work. Signed-off-by: Linus Walleij <[email protected]>
2021-03-30dt-bindings: nvmem: mediatek: add support for MediaTek mt8192 SoCRyan Wu1-0/+1
This updates dt-binding documentation for MediaTek mt8192 Signed-off-by: Ryan Wu <[email protected]> Acked-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-30ARM: dts: imx6: pbab01: Set USB OTG port to peripheralStefan Riedmueller1-0/+1
Due to a hardware bug preventing the correct detection if the ID pin the USB OTG port cannot be used in otg mode. It can either be set to host or peripheral. Set it to peripheral so vbus is disabled by default. Signed-off-by: Stefan Riedmueller <[email protected]> Reviewed-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2021-03-30ARM: dts: imx6: pfla02: Fix USB vbus enable pinmuxingStefan Riedmueller1-4/+4
The pinmuxing for the enable pin of the usbh1 node is wrong. It needs to be muxed as GPIO. While at it, move the pinctrl to the vbus regulator since it is actually the regulator enable pin. Signed-off-by: Stefan Riedmueller <[email protected]> Reviewed-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2021-03-29arm64: dts: qcom: sm8350: Add thermal zones and throttling supportRobert Foss1-0/+826
sm8350 has 29 thermal sensors split across two tsens controllers. Add the thermal zones to expose them and wireup the cpus to throttle their frequencies on crossing passive temperature thresholds. Signed-off-by: Robert Foss <[email protected]> Reviewed-by: Vinod Koul <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]>
2021-03-29arm64: dts: qcom: sm8150: add i2c nodesCaleb Connolly1-0/+521
Tested on the OnePlus 7 Pro (including DMA). Signed-off-by: Caleb Connolly <[email protected]> Reviewed-by: Vinod Koul <[email protected]> Reviewed-by: Bhupesh Sharma <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]>
2021-03-29arm64: dts: qcom: sm8150: add other QUP nodes and iommusCaleb Connolly1-0/+28
Add the first and third qupv3 nodes used to hook up peripherals on some devices, as well as the iommus properties for all of them. Signed-off-by: Caleb Connolly <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]>
2021-03-29arm64: dts: qcom: sm8250: fix display nodesJonathan Marek1-21/+6
Apply these fixes to the newly added sm8250 display ndoes - Remove "notused" interconnect (which apparently was blindly copied from my old patches) - Use dispcc node example from dt-bindings, removing clocks which aren't documented or used by the driver and fixing the region size. Fixes: 7c1dffd471b1 ("arm64: dts: qcom: sm8250.dtsi: add display system nodes") Signed-off-by: Jonathan Marek <[email protected]> [DB: compatibility changes split into separate patch] Signed-off-by: Dmitry Baryshkov <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]>
2021-03-29arm64: dts: broadcom: bcm4908: add Ethernet MAC addrRafał Miłecki2-0/+28
On most BCM4908 devices MAC address can be read from the bootloader binary section containing device settings. Use NVMEM to describe that. Signed-off-by: Rafał Miłecki <[email protected]> Signed-off-by: Florian Fainelli <[email protected]>
2021-03-29ARM: dts: BCM5301X: Set Linksys EA9500 power LEDRafał Miłecki1-0/+1
Set Linux default trigger to default on, just like it's normally done for power LEDs. Signed-off-by: Rafał Miłecki <[email protected]> Signed-off-by: Florian Fainelli <[email protected]>
2021-03-29ARM: dts: BCM5301X: Fix Linksys EA9500 partitionsRafał Miłecki1-9/+7
Partitions are basically fixed indeed but firmware ones don't have hardcoded function ("firmware" vs "failsafe"). Actual function depends on bootloader configuration. Use a proper binding for that. While at it fix numbers formatting to avoid: arch/arm/boot/dts/bcm47094-linksys-panamera.dt.yaml: partitions: 'partition@1F00000' does not match any of the regexes: '^partition@[0-9a-f]+$', 'pinctrl-[0-9]+' From schema: Documentation/devicetree/bindings/mtd/partitions/linksys,ns-partitions.yaml Signed-off-by: Rafał Miłecki <[email protected]> Signed-off-by: Florian Fainelli <[email protected]>
2021-03-29arm64: dts: mt8173: fix wrong power-domain phandle of pmicChunfeng Yun1-1/+1
Due to power domain controller is added, the power domain's phanle is also changed from 'scpsys' to 'spm', but forget to modify pmic node's Fixes: 8b6562644df9 ("arm64: dts: mediatek: Add mt8173 power domain controller") Signed-off-by: Chunfeng Yun <[email protected]> Reviewed-by: Enric Balletbo i Serra <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mt8183: Configure CPU coolingMatthias Kaehlcke1-0/+56
Add two passive trip points at 68°C and 80°C for the CPU temperature. Signed-off-by: Matthias Kaehlcke <[email protected]> Signed-off-by: Michael Kao <[email protected]> Tested-by: Hsin-Yi Wang <[email protected]> Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mt8183: add thermal zone nodemichael.kao1-0/+85
Add thermal zone node to Mediatek MT8183 dts file. Evaluate the thermal zone every 500ms while not cooling and every 100ms when passive cooling is performed. Signed-off-by: Matthias Kaehlcke <[email protected]> Tested-by: Hsin-Yi Wang <[email protected]> Signed-off-by: Michael Kao <[email protected]> Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mt8183: Add gce client reg for display subcomponentsHsin-Yi Wang1-0/+7
Add mediatek,gce-client-reg for mmsys, ccorr, aal, gamma, dither. Fixes: 91f9c963ce79 ("arm64: dts: mt8183: Add display nodes for MT8183") Signed-off-by: Hsin-Yi Wang <[email protected]> Tested-by: Enric Balletbo i Serra <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm: dts: mt2701: harmonize node names and compatiblesChunfeng Yun1-8/+11
This is used to fix dtbs_check warning Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm: dts: mt7623: harmonize node names and compatiblesChunfeng Yun2-14/+16
This is used to fix dtbs_check warning Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm: dts: mt7629: harmonize node names and compatiblesChunfeng Yun1-5/+7
This is used to fix dtbs_check warning Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mediatek: mt8183: fix dtbs_check warningChunfeng Yun1-5/+3
Harmonize node names, compatibles and properties. Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mediatek: mt7622: harmonize node names and compatiblesChunfeng Yun1-4/+5
This is used to fix dtbs_check warning Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mediatek: mt8516: harmonize node names and compatiblesChunfeng Yun2-4/+6
This is used to fix dtbs_check warning: harmonize node names and compatibles; add property "usb-role-switch" for connector dependence. Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mediatek: mt2712: harmonize node namesChunfeng Yun1-4/+4
This is used to fix dtbs_check warning. Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mediatek: mt8173: fix dtbs_check warningChunfeng Yun2-9/+8
Harmonize nodes names, compatibles and remove unused property. Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mt8173: fix property typo of 'phys' in dsi nodeChunfeng Yun1-1/+1
Use 'phys' instead of 'phy'. Fixes: 81ad4dbaf7af ("arm64: dts: mt8173: Add display subsystem related nodes") Signed-off-by: Chunfeng Yun <[email protected]> Reviewed-by: Chun-Kuang Hu <[email protected]> Cc: stable <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29dt-bindings: arm: Add compatible for Mediatek MT8195Seiya Wang1-0/+4
This commit adds dt-binding documentation for the Mediatek MT8195 reference board. Signed-off-by: Seiya Wang <[email protected]> Acked-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29dt-bindings: serial: Add compatible for Mediatek MT8195Seiya Wang1-0/+1
This commit adds dt-binding documentation of uart for Mediatek MT8195 SoC Platform. Signed-off-by: Seiya Wang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29dt-bindings: timer: Add compatible for Mediatek MT8195Seiya Wang1-0/+1
This commit adds dt-binding documentation of timer for Mediatek MT8195 SoC Platform. Signed-off-by: Seiya Wang <[email protected]> Acked-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mt8183: Add kukui-jacuzzi-juniper boardHsin-Yi Wang3-0/+41
Juniper is known as Acer Chromebook Spin 311 (CP311-3H). Signed-off-by: Hsin-Yi Wang <[email protected]> Tested-by: Ricardo Cañuelo <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mt8183: Add kukui-jacuzzi-damu boardHsin-Yi Wang3-0/+506
Damu is known as ASUS Chromebook Flip CM3. Signed-off-by: Hsin-Yi Wang <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-jacuzzi-juniperHsin-Yi Wang1-0/+5
mt8183-kukui-jacuzzi-juniper board also known as Acer Chromebook Spin 311, using mediatek mt8183 SoC. Signed-off-by: Hsin-Yi Wang <[email protected]> Reviewed-by: Enric Balletbo i Serra <[email protected]> Acked-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29dt-bindings: arm64: dts: mediatek: Add mt8183-kukui-jacuzzi-damuHsin-Yi Wang1-0/+4
mt8183-kukui-jacuzzi-damu board also known as ASUS Chromebook Flip CM3, using mediatek mt8183 SoC. Signed-off-by: Hsin-Yi Wang <[email protected]> Reviewed-by: Enric Balletbo i Serra <[email protected]> Acked-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29arm64: dts: mt8183: update wakeup register offsetChunfeng Yun1-1/+1
Use wakeup control register offset exactly, and update revision number Signed-off-by: Chunfeng Yun <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Matthias Brugger <[email protected]>
2021-03-29ARM: dts: stm32: enable the analog filter for all I2C nodes in stm32mp151Alain Volmat1-0/+6
Enable the analog filter for all I2C nodes of the stm32mp151. Signed-off-by: Alain Volmat <[email protected]> Signed-off-by: Alexandre Torgue <[email protected]>
2021-03-29arm64: dts: renesas: r8a779a0: Fix PMU interruptYoshihiro Shimoda1-4/+1
Should use PPI No.7 for the PMU. Otherwise, the perf command didn't show any information. Fixes: 834c310f5418 ("arm64: dts: renesas: Add Renesas R8A779A0 SoC support") Signed-off-by: Yoshihiro Shimoda <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Geert Uytterhoeven <[email protected]>
2021-03-29arm64: dts: renesas: r8a779a0: Add VSPD supportKieran Bingham1-0/+22
Provide VSPD support on the R-Car V3U SoC. Signed-off-by: Kieran Bingham <[email protected]> Reviewed-by: Laurent Pinchart <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Geert Uytterhoeven <[email protected]>
2021-03-29arm64: dts: renesas: r8a779a0: Add FCPVD supportKieran Bingham1-0/+16
Provide FCPVD support for the R-Car V3U SoC. Signed-off-by: Kieran Bingham <[email protected]> Reviewed-by: Laurent Pinchart <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Geert Uytterhoeven <[email protected]>
2021-03-29arm64: dts: renesas: falcon-cpu: Add GP LEDsKieran Bingham1-0/+25
Three general purpose LEDs are provided on the Falcon CPU board. Connect GP_LED1, GP_LED2, and GP_LED3 to the gpio-leds frameworks as indicator LEDs. These LEDs are arranged in a block of four LEDs on the board itself, but the fourth LED is as yet unidentified. Signed-off-by: Kieran Bingham <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Geert Uytterhoeven <[email protected]>
2021-03-29arm64: dts: fsl-ls1028a-kontron-sl28: add rtc0 aliasMichael Walle1-1/+2
For completeness, add the rtc0 alias. Signed-off-by: Michael Walle <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2021-03-29arm64: dts: ls1028a: move rtc alias to individual boardsMichael Walle4-4/+3
The aliases are board-specific and shouldn't be included in the common SoC dtsi. Move them over to the boards. Signed-off-by: Michael Walle <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2021-03-29arm64: dts: fsl-ls1028a-kontron-sl28: combine unused partitionsMichael Walle1-19/+1
The failsafe partitions for the DP firmware and for AT-F are unused. If AT-F will ever be supported in the failsafe mode, then it will be a FIT image. Thus fold the unused partitions into the failsafe bootloader one to have enough storage if the bootloader image will grow. While at it, remove the reserved partition. It served no purpose other than having no hole in the map. Signed-off-by: Michael Walle <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2021-03-29arm64: dts: fsl-ls1028a-kontron-sl28: move MTD partitionsMichael Walle1-45/+49
Move the MTD partitions to the partitions subnode. This is the new way to specify the partitions, see Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml Signed-off-by: Michael Walle <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2021-03-29arm64: dts: imx8mp-evk: Improve the Ethernet PHY descriptionFabio Estevam1-0/+2
According to the datasheet RTL8211, it must be asserted low for at least 10ms and at least 72ms "for internal circuits settling time" before accessing the PHY registers. Add properties to describe such requirements. Reported-by: Joakim Zhang <[email protected]> Signed-off-by: Fabio Estevam <[email protected]> Tested-by: Joakim Zhang <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2021-03-29arm64: dts: imx8mq-librem5-r3: Mark buck3 as always onSebastian Krzyszkowiak1-0/+4
Commit 99e71c029213 ("arm64: dts: imx8mq-librem5: Don't mark buck3 as always on") removed always-on marking from GPU regulator, which is great for power saving - however it introduces additional i2c0 traffic which can be deadly for devices from the Dogwood batch. To workaround the i2c0 shutdown issue on Dogwood, this commit marks buck3 as always-on again - but only for Dogwood (r3). Signed-off-by: Sebastian Krzyszkowiak <[email protected]> Signed-off-by: Martin Kepplinger <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.