| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Conflicts:
drivers/clk/Kconfig
|
|
This driver supports the TI CDCE925 programmable clock synthesizer.
The chip contains two PLLs with spread-spectrum clocking support and
five output dividers. The driver only supports the following setup,
and uses a fixed setting for the output muxes:
Y1 is derived from the input clock
Y2 and Y3 derive from PLL1
Y4 and Y5 derive from PLL2
Given a target output frequency, the driver will set the PLL and
divider to best approximate the desired output.
Signed-off-by: Mike Looijmans <[email protected]>
Signed-off-by: Michael Turquette <[email protected]>
|
|
Even if not documented in the datasheet, the Armada 370 SoC can actually
gate the CESA (crypto engine) clock.
Add an entry in the gating_desc table to be able to reference the CESA
gateclk in the crypto node.
Signed-off-by: Boris Brezillon <[email protected]>
Acked-by: Gregory CLEMENT <[email protected]>
Signed-off-by: Michael Turquette <[email protected]>
|
|
Add clock drivers for hi6220 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.
We add one divider clock for hi6220 because the divider in hi6220
also has a mask bit but it doesnot obey the rule defined by flag
"CLK_DIVIDER_HIWORD_MASK", we can not get index of the mask bit by
left shift fixed bits (e.g. 16 bits), so we add this divider clock
to handle it.
Signed-off-by: Jorge Ramirez-Ortiz <[email protected]>
Signed-off-by: Bintian Wang <[email protected]>
Acked-by: Haojian Zhuang <[email protected]>
Reviewed-by: Zhangfei Gao <[email protected]>
Tested-by: Will Deacon <[email protected]>
Tested-by: Tyler Baker <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
Signed-off-by: Michael Turquette <[email protected]>
|
|
This patch fixes a bug where the number of watch points
was shown before it was actually calculated
Signed-off-by: Alexey Skidanov <[email protected]>
Cc: [email protected]
Signed-off-by: Oded Gabbay <[email protected]>
|
|
Add the header file "hi6220-clock.h" used by both
hi6220 clock driver and hi6220 device tree file.
Suggested-by: Stephen Boyd <[email protected]>
Signed-off-by: Bintian Wang <[email protected]>
Tested-by: Will Deacon <[email protected]>
Tested-by: Tyler Baker <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
Signed-off-by: Michael Turquette <[email protected]>
|
|
__init markings on function prototypes are useless, so remove
them.
Suggested-by: Stephen Boyd <[email protected]>
Signed-off-by: Bintian Wang <[email protected]>
Tested-by: Will Deacon <[email protected]>
Tested-by: Tyler Baker <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
Signed-off-by: Michael Turquette <[email protected]>
|
|
strnlen_user() can return a number in a range 0 to count +
sizeof(unsigned long) - 1. Clarify the comment at the top of the
function so that users don't think the function returns at most count+1.
Signed-off-by: Jan Kara <[email protected]>
[ Also added commentary about preferably not using this function ]
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The driver worked around an error in the MAYA44 USB(+)'s mixer unit
descriptor by aborting before parsing the missing field. However,
aborting parsing too early prevented parsing of the other units
connected to this unit, so the capture mixer controls would be missing.
Fix this by moving the check for this descriptor error after the parsing
of the unit's input pins.
Reported-by: nightmixes <[email protected]>
Tested-by: nightmixes <[email protected]>
Signed-off-by: Clemens Ladisch <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Add mixer control names for the ESI Maya44 USB+ (which appears to be
identical width the AudioTrak Maya44 USB).
Reported-by: nightmixes <[email protected]>
Signed-off-by: Clemens Ladisch <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Use the default FCSR value in mask probing, avoiding an FPE exception
where reset has left any exception enable and their corresponding cause
bits set and the register is then rewritten with these bits active.
Signed-off-by: Maciej W. Rozycki <[email protected]>
Cc: Joshua Kinard <[email protected]>
Cc: [email protected]
Signed-off-by: Ralf Baechle <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 fix from Tony Luck:
"Fix some build warnings for ia64 - cpu_callin_map doesn't need to be
volatile"
* tag 'please-pull-rusty' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
ia64: make cpu_callin_map non-volatile.
|
|
Acer Aspire 9420 with ALC883 (1025:0107) needs the fixup for EAPD to
make the sound working like other Aspire models.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94111
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
known rate
Make the check to skip the rate check more lax, so that it applies
to all hw_version 4 models.
This fixes the touchpad not being detected properly on Asus PU551LA
laptops.
Cc: [email protected]
Reported-and-tested-by: David Zafra Gómez <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
We used to read file_handle twice. Once to get the amount of extra
bytes, and once to fetch the entire structure.
This may be problematic since we do size verifications only after the
first read, so if the number of extra bytes changes in userspace between
the first and second calls, we'll have an incoherent view of
file_handle.
Instead, read the constant size once, and copy that over to the final
structure without having to re-read it again.
Signed-off-by: Sasha Levin <[email protected]>
Cc: Al Viro <[email protected]>
Cc: [email protected]
Signed-off-by: Linus Torvalds <[email protected]>
|
|
If the specified maximum length of the string is a multiple of unsigned
long, we would load one long behind the specified maximum. If that
happens to be in a next page, we can hit a page fault although we were
not expected to.
Fix the off-by-one bug in the test whether we are at the end of the
specified range.
Signed-off-by: Jan Kara <[email protected]>
Cc: [email protected]
Signed-off-by: Linus Torvalds <[email protected]>
|
|
cpumask_test_cpu() doesn't take volatile, unlike the obsoleted
cpu_isset. The only place ia64 really cares is the spin waiting for a
bit; udelay() is probably a barrier but insert barrier() to be sure.
Signed-off-by: Rusty Russell <[email protected]>
Signed-off-by: Tony Luck <[email protected]>
|
|
The memory setup log is missing a new line.
Signed-off-by: Alban Bedel <[email protected]>
Cc: [email protected]
Cc: Andrew Bresticker <[email protected]>
Cc: Qais Yousef <[email protected]>
Cc: Wolfram Sang <[email protected]>
Cc: Sergey Ryazanov <[email protected]>
Cc: Gabor Juhos <[email protected]>
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/9771/
Signed-off-by: Ralf Baechle <[email protected]>
|
|
The vd->node is removed from the lists when the transfer started so the
vchan_get_all_descriptors() will not find it. This results memory leak.
Signed-off-by: Peter Ujfalusi <[email protected]>
[andy: fix the typo to prevent a compilation error]
Signed-off-by: Andy Shevchenko <[email protected]>
Signed-off-by: Vinod Koul <[email protected]>
|
|
The usb-clk on sun8i a23 and a33 SoCs is similar to the ones found
on sun6i-a31 SoCs but instead of a 3th phy the a23 / a33 have a hsic
interface which gets enabled by almost the same bits as used on
the a31 for the 3rd phy, but not exactly the same bits so we need
a new compatible for this.
Signed-off-by: Hans de Goede <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Reviewed-by: Chen-Yu Tsai <[email protected]>
|
|
The early_idt_handlers asm code generates an array of entry
points spaced nine bytes apart. It's not really clear from that
code or from the places that reference it what's going on, and
the code only works in the first place because GAS never
generates two-byte JMP instructions when jumping to global
labels.
Clean up the code to generate the correct array stride (member size)
explicitly. This should be considerably more robust against
screw-ups, as GAS will warn if a .fill directive has a negative
count. Using '. =' to advance would have been even more robust
(it would generate an actual error if it tried to move
backwards), but it would pad with nulls, confusing anyone who
tries to disassemble the code. The new scheme should be much
clearer to future readers.
While we're at it, improve the comments and rename the array and
common code.
Binutils may start relaxing jumps to non-weak labels. If so,
this change will fix our build, and we may need to backport this
change.
Before, on x86_64:
0000000000000000 <early_idt_handlers>:
0: 6a 00 pushq $0x0
2: 6a 00 pushq $0x0
4: e9 00 00 00 00 jmpq 9 <early_idt_handlers+0x9>
5: R_X86_64_PC32 early_idt_handler-0x4
...
48: 66 90 xchg %ax,%ax
4a: 6a 08 pushq $0x8
4c: e9 00 00 00 00 jmpq 51 <early_idt_handlers+0x51>
4d: R_X86_64_PC32 early_idt_handler-0x4
...
117: 6a 00 pushq $0x0
119: 6a 1f pushq $0x1f
11b: e9 00 00 00 00 jmpq 120 <early_idt_handler>
11c: R_X86_64_PC32 early_idt_handler-0x4
After:
0000000000000000 <early_idt_handler_array>:
0: 6a 00 pushq $0x0
2: 6a 00 pushq $0x0
4: e9 14 01 00 00 jmpq 11d <early_idt_handler_common>
...
48: 6a 08 pushq $0x8
4a: e9 d1 00 00 00 jmpq 120 <early_idt_handler_common>
4f: cc int3
50: cc int3
...
117: 6a 00 pushq $0x0
119: 6a 1f pushq $0x1f
11b: eb 03 jmp 120 <early_idt_handler_common>
11d: cc int3
11e: cc int3
11f: cc int3
Signed-off-by: Andy Lutomirski <[email protected]>
Acked-by: H. Peter Anvin <[email protected]>
Cc: Binutils <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: H.J. Lu <[email protected]>
Cc: Jan Beulich <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: <[email protected]>
Link: http://lkml.kernel.org/r/ac027962af343b0c599cbfcf50b945ad2ef3d7a8.1432336324.git.luto@kernel.org
Signed-off-by: Ingo Molnar <[email protected]>
|
|
This reverts commit 5fc872c7323534e8f7dc21bab635e7a9b9659e07.
The DMA-API does not strictly require that the memory
returned by dma_alloc_coherent is zeroed out. For that
another function (dma_zalloc_coherent) should be used. But
all other x86 DMA-API implementation I checked zero out the
memory, so that some drivers rely on it and break when it is
not.
It seems the (driver-)world is not yet ready for this
change, so revert it.
Signed-off-by: Joerg Roedel <[email protected]>
|
|
Pull networking fixes from David Miller:
1) Various VTI tunnel (mark handling, PMTU) bug fixes from Alexander
Duyck and Steffen Klassert.
2) Revert ethtool PHY query change, it wasn't correct. The PHY address
selected by the driver running the PHY to MAC connection decides
what PHY address GET ethtool operations return information from.
3) Fix handling of sequence number bits for encryption IV generation in
ESP driver, from Herbert Xu.
4) UDP can return -EAGAIN when we hit a bad checksum on receive, even
when there are other packets in the receive queue which is wrong.
Just respect the error returned from the generic socket recv
datagram helper. From Eric Dumazet.
5) Fix BNA driver firmware loading on big-endian systems, from Ivan
Vecera.
6) Fix regression in that we were inheriting the congestion control of
the listening socket for new connections, the intended behavior
always was to use the default in this case. From Neal Cardwell.
7) Fix NULL deref in brcmfmac driver, from Arend van Spriel.
8) OTP parsing fix in iwlwifi from Liad Kaufman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
vti6: Add pmtu handling to vti6_xmit.
Revert "net: core: 'ethtool' issue with querying phy settings"
bnx2x: Move statistics implementation into semaphores
xen: netback: read hotplug script once at start of day.
xen: netback: fix printf format string warning
Revert "netfilter: ensure number of counters is >0 in do_replace()"
net: dsa: Properly propagate errors from dsa_switch_setup_one
tcp: fix child sockets to use system default congestion control if not set
udp: fix behavior of wrong checksums
sfc: free multiple Rx buffers when required
bna: fix soft lock-up during firmware initialization failure
bna: remove unreasonable iocpf timer start
bna: fix firmware loading on big-endian machines
bridge: fix br_multicast_query_expired() bug
via-rhine: Resigning as maintainer
brcmfmac: avoid null pointer access when brcmf_msgbuf_get_pktid() fails
mac80211: Fix mac80211.h docbook comments
iwlwifi: nvm: fix otp parsing in 8000 hw family
iwlwifi: pcie: fix tracking of cmd_in_flight
ip_vti/ip6_vti: Preserve skb->mark after rcv_cb call
...
|
|
Pull Sparc fixes from David Miller:
1) Setup the core/threads/sockets bitmaps correctly so that 'lscpus'
and friends operate properly. Frtom Chris Hyser.
2) The bit that normally means "Cached Virtually" on sun4v systems,
actually changes meaning in M7 and later chips. Fix from Khalid
Aziz.
3) One some PCI-E systems we need to probe different OF properties to
fill in the PCI slot information properly, from Eric Snowberg.
4) Kill an extraneous memset after kzalloc(), from Christophe Jaillet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Resolve conflict between sparc v9 and M7 on usage of bit 9 of TTE
sparc64: pci slots information is not populated in sysfs
sparc: kernel: GRPCI2: Remove a useless memset
sparc64: Setup sysfs to mark LDOM sockets, cores and threads correctly
|
|
Using the DCE2 one by accident afer the audio rework.
Bug:
https://bugs.freedesktop.org/show_bug.cgi?id=90777
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
Pull virtio fix from Michael Tsirkin:
"Last-minute virtio fix for 4.1
This tweaks an exported user-space header to fix build breakage for
userspace using it"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
include/uapi/linux/virtio_balloon.h: include linux/virtio_types.h
|
|
Pablo Neira Ayuso says:
====================
Netfilter fix for net
The following patch reverts the ebtables chunk that enforces counters that was
introduced in the recently applied d26e2c9ffa38 ('Revert "netfilter: ensure
number of counters is >0 in do_replace()"') since this breaks ebtables.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* fix OTP parsing 8260
* fix powersave handling for 8260
brcmfmac:
* fix null pointer crash
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
We currently rely on the PMTU discovery of xfrm.
However if a packet is localy sent, the PMTU mechanism
of xfrm tries to to local socket notification what
might not work for applications like ping that don't
check for this. So add pmtu handling to vti6_xmit to
report MTU changes immediately.
Signed-off-by: Steffen Klassert <[email protected]>
Signed-off-by: Alexander Duyck <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing
and assigning"), we store additional alignment in realloc_head and take
this into consideration for assignment.
In __assign_resources_sorted(), we changed dev_res->res->start, then used
resource_start() (which depends on res->start), so the recomputed res->end
was completely bogus. Even if we'd had the correct size, the end would
have been off by one.
Preserve the resource size when we adjust its alignment.
[bhelgaas: changelog]
Fixes: d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing and assigning")
Signed-off-by: Yinghai Lu <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Acked-by: Wei Yang <[email protected]>
CC: Benjamin Herrenschmidt <[email protected]>
|
|
This reverts commit f96dee13b8e10f00840124255bed1d8b4c6afd6f.
It isn't right, ethtool is meant to manage one PHY instance
per netdevice at a time, and this is selected by the SET
command. Therefore by definition the GET command must only
return the settings for the configured and selected PHY.
Reported-by: Ben Hutchings <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit dff173de84958 ("bnx2x: Fix statistics locking scheme") changed the
bnx2x locking around statistics state into using a mutex - but the lock
is being accessed via a timer which is forbidden.
[If compiled with CONFIG_DEBUG_MUTEXES, logs show a warning about
accessing the mutex in interrupt context]
This moves the implementation into using a semaphore [with size '1']
instead.
Signed-off-by: Yuval Mintz <[email protected]>
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <[email protected]>
Acked-by: Wei Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
drivers/net/xen-netback/netback.c: In function ‘xenvif_tx_build_gops’:
drivers/net/xen-netback/netback.c:1253:8: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘int’ [-Wformat=]
(txreq.offset&~PAGE_MASK) + txreq.size);
^
PAGE_MASK's type can vary by arch, so a cast is needed.
Signed-off-by: Ian Campbell <[email protected]>
----
v2: Cast to unsigned long, since PAGE_MASK can vary by arch.
Acked-by: Wei Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This partially reverts commit 1086bbe97a07 ("netfilter: ensure number of
counters is >0 in do_replace()") in net/bridge/netfilter/ebtables.c.
Setting rules with ebtables does not work any more with 1086bbe97a07 place.
There is an error message and no rules set in the end.
e.g.
~# ebtables -t nat -A POSTROUTING --src 12:34:56:78:9a:bc -j DROP
Unable to update the kernel. Two possible causes:
1. Multiple ebtables programs were executing simultaneously. The ebtables
userspace tool doesn't by default support multiple ebtables programs
running
Reverting the ebtables part of 1086bbe97a07 makes this work again.
Signed-off-by: Bernhard Thaler <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Fixes userspace compilation error:
error: unknown type name ‘__virtio16’
__virtio16 tag;
Signed-off-by: Mikko Rapeli <[email protected]>
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
The generic RZ CPG compatible value is mandatory, as the driver uses
only this value for matching. Document that this is a fallback that
must be present.
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
The generic R-Car Gen2 CPG compatible value is mandatory, as the driver
uses only this value for matching. Document that this is a fallback
that must be present.
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
The generic MSTP gate clocks compatible value is mandatory, as the
driver uses only this value for matching. Document that this is a
fallback that must be present.
Also fix a typo (missing plural "s") in the compatible value.
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
The generic CPG DIV6 clock compatible value is mandatory, as the driver
uses only this value for matching. Document that this is a fallback
that must be present.
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
Signed-off-by: Ulrich Hecht <[email protected]>
Acked-by: Simon Horman <[email protected]>
Cc: [email protected]
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
Also replaces "R-Car M2" with "R-Car M2-W" to avoid confusion.
Signed-off-by: Ulrich Hecht <[email protected]>
Acked-by: Simon Horman <[email protected]>
Cc: Michael Turquette <[email protected]>
Cc: [email protected]
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
Signed-off-by: Ulrich Hecht <[email protected]>
Acked-by: Laurent Pinchart <[email protected]>
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
Due to a typo the illegal access interrupt is never cleared in by
the interupt handler, causing an effective deadlock on the first
illegal access.
This was broken since the code was introduced in 5433acd81e87 ("MIPS:
ralink: add illegal access driver"), but only exposed when the Kconfig
symbol was added, thus enabling the code.
Cc: <[email protected]> [3.18+]
Fixes: a7b7aad383c ("MIPS: ralink: add missing symbol for RALINK_ILL_ACC")
Signed-off-by: Jonas Gorski <[email protected]>
Cc: [email protected]
Cc: John Crispin <[email protected]>
Patchwork: https://patchwork.linux-mips.org/patch/10172/
Signed-off-by: Ralf Baechle <[email protected]>
|
|
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <[email protected]>
Reviewed-by: Chris Wilson <[email protected]>
Cc: [email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
According to the HSW b-spec we need to try clock divisors of 63
and 72, each 3 or more times, when attempting DP AUX channel
communication on a server chipset. This actually wasn't happening
due to a short-circuit that only checked the DP_AUX_CH_CTL_DONE bit
in status rather than checking that the operation was done and
that DP_AUX_CH_CTL_TIME_OUT_ERROR was not set.
[v2] Implemented alternate solution suggested by Jani Nikula.
Cc: [email protected]
Signed-off-by: Jim Bride <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
|
|
sparc: Resolve conflict between sparc v9 and M7 on usage of bit 9 of TTE
Bit 9 of TTE is CV (Cacheable in V-cache) on sparc v9 processor while
the same bit 9 is MCDE (Memory Corruption Detection Enable) on M7
processor. This creates a conflicting usage of the same bit. Kernel
sets TTE.cv bit on all pages for sun4v architecture which works well
for sparc v9 but enables memory corruption detection on M7 processor
which is not the intent. This patch adds code to determine if kernel
is running on M7 processor and takes steps to not enable memory
corruption detection in TTE erroneously.
Signed-off-by: Khalid Aziz <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add PCI slot numbers within sysfs for PCIe hardware. Larger
PCIe systems with nested PCI bridges and slots further
down on these bridges were not being populated within sysfs.
This will add ACPI style PCI slot numbers for these systems
since the OF 'slot-names' information is not available on
all PCIe platforms.
Signed-off-by: Eric Snowberg <[email protected]>
Reviewed-by: Bob Picco <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
grpci2priv is allocated using kzalloc, so there is no need to memset it.
Signed-off-by: Christophe Jaillet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|