| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[Why]
A number of DML parameters related to HostVM were either missing or
being set incorrectly, which may cause inaccuracies in calculating
margins and determining BW limitations.
[How]
Correct these values where needed and populate the missing values.
Cc: [email protected]
Reviewed-by: Nicholas Kazlauskas <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Taimur Hassan <[email protected]>
Signed-off-by: Roman Li <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Memory leaks of gang_ctx_bo and wptr_bo.
[How]
Free gang_ctx_bo and wptr_bo in pqm_uninit.
v2: add a common function pqm_clean_queue_resource to
free queue's resources.
v3: reset pdd->pqd.num_gws when destorying GWS queue.
Reviewed-by: Felix Kuehling <[email protected]>
Signed-off-by: ZhenGuo Yin <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Check smu v13_0_0 SKU type to select EEPROM I2C address.
Signed-off-by: Candice Li <[email protected]>
Reviewed-by: Hawking Zhang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected] # 6.1.x
|
|
[Why]
DTBCLK is enabled on idle and it will burn power.
[How]
There's a few issues here:
- Always enabling DTBCLK on clock manager init
- Setting refclk when DTBCLK is supposed to be disabled
- Not applying the correct calculated version refclk, but instead the
base value which might be zero
On dtbclk_en change we'll message PMFW to enable or disable the clock
accordingly.
The DTBDTO will be then based on refclk, but it will be set to the
default fixed value if there was nothing calculated in DML despite the
clock being considered enabled.
Reviewed-by: Charlene Liu <[email protected]>
Acked-by: Tom Chung <[email protected]>
Signed-off-by: Nicholas Kazlauskas <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
For 'AMDGPU_FAMILY_SI' family cards, in 'si_common_early_init' func, init
'didt_rreg' and 'didt_wreg' to 'NULL'. But in func
'amdgpu_debugfs_regs_didt_read/write', using 'RREG32_DIDT' 'WREG32_DIDT'
lacks of relevant judgment. And other 'amdgpu_ip_block_version' that use
these two definitions won't be added for 'AMDGPU_FAMILY_SI'.
So, add null pointer judgment before calling.
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Lu Yao <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
When dGPU is put into BOCO it may be in D3cold but still able send
PME on display hotplug event. For this to work it must be enabled
as wake source from D3.
When runpm is enabled use pci_wake_from_d3() to mark wakeup as
enabled by default.
Cc: [email protected] # 6.1+
Signed-off-by: Mario Limonciello <[email protected]>
Acked-by: Alex Deucher <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
When kzalloc() for smu_table->ecc_table fails, we should free
the previously allocated resources to prevent memleak.
Fixes: edd794208555 ("drm/amd/pm: add message smu to get ecc_table v2")
Signed-off-by: Dinghao Liu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
This worked by luck if the GART aperture ended up at 0. When
we ended up moving GART on some chips, the GART aperture ended
up offsetting the AGP address since the resource->start is
a GART offset, not an MC address. Fix this by moving the AGP
address setup into amdgpu_bo_gpu_offset_no_check().
v2: check mem_type before checking agp
v3: check if the ttm bo has a ttm_tt allocated yet
Fixes: 67318cb84341 ("drm/amdgpu/gmc11: set gart placement GC11")
Tested-by: Mario Limonciello <[email protected]>
Reported-by: Jesse Zhang <[email protected]>
Reported-by: Yifan Zhang <[email protected]>
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
Cc: [email protected]
|
|
[WHY/HOW]
Increase the pstate latency to improve ac/dc transition
Reviewed-by: Charlene Liu <[email protected]>
Acked-by: Tom Chung <[email protected]>
Signed-off-by: Dmytro Laktyushkin <[email protected]>
Tested-by: Daniel Wheeler <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
On recent versions of DMUB firmware, if we want to completely disable
ABM we have to pass ABM_LEVEL_IMMEDIATE_DISABLE as the requested ABM
level to DMUB. Otherwise, LCD eDP displays are unable to reach their
maximum brightness levels. So, to fix this whenever the user requests an
ABM level of 0 pass ABM_LEVEL_IMMEDIATE_DISABLE to DMUB instead. Also,
to keep the user's experience consistent map ABM_LEVEL_IMMEDIATE_DISABLE
to 0 when a user tries to read the requested ABM level.
Cc: [email protected] # 6.1+
Reviewed-by: Harry Wentland <[email protected]>
Signed-off-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[why]
We have dynamic power control in driver but
should be ignored when power is forced on.
[how]
Bypass any power control when it's forced on.
Cc: [email protected]
Reviewed-by: Nicholas Kazlauskas <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Sung Joon Kim <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
There are a number of instances where we convert HostVMMinPageSize or
GPUVMMinPageSize from bytes to KB by dividing (rather than multiplying) and
vice versa.
Additionally, in some cases, a parameter is passed through DML in KB but
later checked as if it were in bytes.
Cc: [email protected]
Reviewed-by: Nicholas Kazlauskas <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Taimur Hassan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
KFD_GC_VERSION was recently updated to use a new function
for IP version checks. As a result, use KFD_GC_VERSION as
the common function for all IP version checks in KFD.
Signed-off-by: Mukul Joshi <[email protected]>
Reviewed-by: Harish Kasiviswanathan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Prevent overwrite of dc->config.use_default_clock_table, as it should be
pre-configured.
Reviewed-by: Nicholas Kazlauskas <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Taimur Hassan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
The new table doesn't have an implicit mapping between Fclk SOC voltage
and MemClk and it currently builds the table off of number of Fclk
states rather than DcfClock states.
The DML table in use is not correct for functionality or power and
does not align with our existing policies for DCN3x.
[How]
Build the table based on DcfClock with the following assumptions:
1. Raising Soc voltage is the most expensive operation, so assume that
running at max DispClock or DppClock is preferable.
2. Assume that we can run at max Fclk / MemClk at any state, but
restrict the maximum state to the very last entry in the table as the
worst case scenario.
3. Assume that Fclk always has a 2x multiplier on DcfClock unless the
table specifies something lower.
Reviewed-by: Taimur Hassan <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Nicholas Kazlauskas <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[WHY]
Handover from DMUB to driver does not perform link rate toggle.
It might cause link training failure for boot up.
[HOW]
Force toggle rate wa for first link train.
link->vendor_specific_lttpr_link_rate_wa should be zero then.
Cc: [email protected] # 6.1+
Reviewed-by: Michael Strauss <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Zhongwei <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Fix the amdgpu runpm dereference usage count.
Signed-off-by: Prike Liang <[email protected]>
Reviewed-by: Alex Deucher <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
[Why]
Some panels with residency period of 2054 exhibit flickering with
Z8 at the end of the frame.
[How]
As a workaround, increase the limit to block these panels.
Cc: [email protected] # 6.1+
Reviewed-by: Syed Hassan <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Nicholas Kazlauskas <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Flickering occurs on DRR supported panels when engaged in DRR due to
min_dst_y_next becoming larger than the frame size itself.
[How]
In general, we should be able to enter Z8 when this is engaged but it
might be a net power loss even if the calculation wasn't bugged.
Don't support enabling Z8 during the DRR region.
Cc: [email protected] # 6.1+
Reviewed-by: Syed Hassan <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Nicholas Kazlauskas <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Fix a memory overflow issue in the gfx IB test
for some ASICs. At least 20 bytes are needed for
the IB test packet.
v2: correct code indentation errors. (Christian)
Signed-off-by: Tim Huang <[email protected]>
Reviewed-by: Yifan Zhang <[email protected]>
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
enable init_registers callback func for nbio v7.11.
Signed-off-by: Li Ma <[email protected]>
Reviewed-by: Yifan Zhang <[email protected]>
Acked-by: Alex Deucher <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Remove the brightness cache in DC. It uses a single value to represent
the brightness for both SDR and HDR mode. This leads to flash in HDR
on/off. It also unconditionally programs brightness as in HDR mode. This
may introduce garbage on SDR mode in miniLED panel.
[How]
Simplify the initialization flow by removing the DC cache and taking
what panel has as default. Expand the mechanism for PWM to DPCD Aux to
restore cached brightness value generally.
Cc: [email protected] # 6.1+
Reviewed-by: Krunoslav Kovac <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Camille Cho <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Description]
If during driver init stage there are greater than 20
intermediary voltage states while constructing the SOC
BB we could hit issues because we will index outside of the
clock_limits array and start overwriting data. Increase the
total number of states to 40 to avoid this issue.
Cc: [email protected] # 6.1+
Reviewed-by: Samson Tam <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Alvin Lee <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[WHY]
Currently DCN35 does not spread DPREFCLK
[HOW]
Remove hardcoded table with nonzero caps
Reviewed-by: Nicholas Kazlauskas <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Michael Strauss <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Description]
When choosing which dummy p-state latency to use, we
need to use the DRAM speed from validation. The DRAMSpeed
DML variable can change because we use different input
params to DML when populating watermarks set B.
Cc: [email protected] # 6.1+
Reviewed-by: Samson Tam <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Alvin Lee <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
Wrong function is used to translate LUT values to HW format, leading to
visible artifacting in some cases.
[How]
Use the correct cm3_helper function.
Cc: [email protected] # 6.1+
Reviewed-by: Krunoslav Kovac <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Ilya Bakoulin <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
We've updated the table but the values aren't being reflected in DML2
calculation.
[How]
Pass them into the bbox overrides.
Reviewed-by: Jun Lei <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Nicholas Kazlauskas <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
Setting register to force ordering to prevent read/write or write/read
hazards for un-cached modes.
Signed-off-by: Alex Sierra <[email protected]>
Acked-by: Alex Deucher <[email protected]>
Reviewed-by: Felix Kuehling <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected] # 6.1.x
|
|
In nbio v7_9, host driver should not issu gpu reset
Signed-off-by: Hawking Zhang <[email protected]>
Reviewed-by: Stanley Yang <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
We can override SR watermarks but not Z8 ones.
[How]
Add new parameters for Z8 matching the SR ones and feed them into the
states.
These also weren't being applied to every state, so make sure that
we loop over and update all SOC states if given an override.
Reviewed-by: Jun Lei <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Nicholas Kazlauskas <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
The smu needs to get the rlc power down message to sync the rlc state
with smu, the rlc state updating message need to be sent at while smu
begin suspend sequence , otherwise SMU will crash while RLC state is not
notified by driver, and rlc state probally changed after that
notification, so it needs to notify rlc state to smu at the end of the
suspend sequence in amdgpu_device_suspend() that can make sure the rlc
state is correctly set to SMU.
[ 101.000590] amdgpu 0000:03:00.0: amdgpu: SMU: I'm not done with your previous command: SMN_C2PMSG_66:0x0000001E SMN_C2PMSG_82:0x00000000
[ 101.000598] amdgpu 0000:03:00.0: amdgpu: Failed to disable gfxoff!
[ 110.838026] amdgpu 0000:03:00.0: amdgpu: SMU: I'm not done with your previous command: SMN_C2PMSG_66:0x0000001E SMN_C2PMSG_82:0x00000000
[ 110.838035] amdgpu 0000:03:00.0: amdgpu: Failed to disable smu features.
[ 110.838039] amdgpu 0000:03:00.0: amdgpu: Fail to disable dpm features!
[ 110.838040] [drm:amdgpu_device_ip_suspend_phase2 [amdgpu]] *ERROR* suspend of IP block <smu> failed -62
[ 110.884394] PM: suspend of devices aborted after 21213.620 msecs
[ 110.884402] PM: start suspend of devices aborted after 21213.882 msecs
[ 110.884405] PM: Some devices failed to suspend, or early wake event detected
Reviewed-by: Yifan Zhang <[email protected]>
Signed-off-by: Perry Yuan <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[why]
In dcn32 DML pipes are ordered the same as dc pipes but only for used
pipes. For example, if dc pipe 1 and 2 are used, their dml pipe indices
would be 0 and 1 respectively. However
update_pipe_slice_table_with_split_flags doesn't skip indices for free
pipes. This causes us to not reference correct dml pipe output when
building pipe topology.
[how]
Use two variables to iterate dc and dml pipes respectively and only
increment dml pipe index when current dc pipe is not free.
Cc: [email protected] # 6.1+
Reviewed-by: Chaitanya Dhere <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Wenjing Liu <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why & How]
Update to the new values per HW team request. Affects both stutter
and z8.
Reviewed-by: Charlene Liu <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Nicholas Kazlauskas <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
GC IP 9.4.2 and up support TA reporting of the number
of xGMI links between peers.
Tested-by: Vignesh Chander <[email protected]>
Signed-off-by: Jonathan Kim <[email protected]>
Reviewed-by: Mukul Joshi <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
[Why]
DML2 means that the dcn3x policy for calculating z-state support
no longer runs from validate_bandwidth.
This means we are unconditionally allowing Z8, the hardware default.
[How]
Port the policy over to DCN35, but with a few modifications:
- Don't use min_dst_y_next_start as a check for Z8/Z10 allow
- Add support for overriding the Z10 stutter period per ASIC
- Cleanup the code to make the policy assignment more clear
Reviewed-by: Charlene Liu <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Nicholas Kazlauskas <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
When waiting for the ACK for INBOX0 message,
we have to ensure to include the udelay
for proper wait time
Cc: [email protected] # 6.1+
Reviewed-by: Samson Tam <[email protected]>
Acked-by: Hamza Mahfooz <[email protected]>
Signed-off-by: Alvin Lee <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt::
"Eventfs fixes:
- With the usage of simple_recursive_remove() recommended by Al Viro,
the code should not be calling "d_invalidate()" itself. Doing so is
causing crashes. The code was calling d_invalidate() on the race of
trying to look up a file while the parent was being deleted. This
was detected, and the added dentry was having d_invalidate() called
on it, but the deletion of the directory was also calling
d_invalidate() on that same dentry.
- A fix to not free the eventfs_inode (ei) until the last dput() was
called on its ei->dentry made the ei->dentry exist even after it
was marked for free by setting the ei->is_freed. But code elsewhere
still was checking if ei->dentry was NULL if ei->is_freed is set
and would trigger WARN_ON if that was the case. That's no longer
true and there should not be any warnings when it is true.
- Use GFP_NOFS for allocations done under eventfs_mutex. The
eventfs_mutex can be taken on file system reclaim, make sure that
allocations done under that mutex do not trigger file system
reclaim.
- Clean up code by moving the taking of inode_lock out of the helper
functions and into where they are needed, and not use the parameter
to know to take it or not. It must always be held but some callers
of the helper function have it taken when they were called.
- Warn if the inode_lock is not held in the helper functions.
- Warn if eventfs_start_creating() is called without a parent. As
eventfs is underneath tracefs, all files created will have a parent
(the top one will have a tracefs parent).
Tracing update:
- Add Mathieu Desnoyers as an official reviewer of the tracing subsystem"
* tag 'trace-v6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
MAINTAINERS: TRACING: Add Mathieu Desnoyers as Reviewer
eventfs: Make sure that parent->d_inode is locked in creating files/dirs
eventfs: Do not allow NULL parent to eventfs_start_creating()
eventfs: Move taking of inode_lock into dcache_dir_open_wrapper()
eventfs: Use GFP_NOFS for allocation when eventfs_mutex is held
eventfs: Do not invalidate dentry in create_file/dir_dentry()
eventfs: Remove expectation that ei->is_freed means ei->dentry == NULL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
"This patchset fixes and enforces correct section alignments for the
ex_table, altinstructions, parisc_unwind, jump_table and bug_table
which are created by inline assembly.
Due to not being correctly aligned at link & load time they can
trigger unnecessarily the kernel unaligned exception handler at
runtime. While at it, I switched the bug table to use relative
addresses which reduces the size of the table by half on 64-bit.
We still had the ENOSYM and EREMOTERELEASE errno symbols as left-overs
from HP-UX, which now trigger build-issues with glibc. We can simply
remove them.
Most of the patches are tagged for stable kernel series.
Summary:
- Drop HP-UX ENOSYM and EREMOTERELEASE return codes to avoid glibc
build issues
- Fix section alignments for ex_table, altinstructions, parisc unwind
table, jump_table and bug_table
- Reduce size of bug_table on 64-bit kernel by using relative
pointers"
* tag 'parisc-for-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Reduce size of the bug_table on 64-bit kernel by half
parisc: Drop the HP-UX ENOSYM and EREMOTERELEASE error codes
parisc: Use natural CPU alignment for bug_table
parisc: Ensure 32-bit alignment on parisc unwind section
parisc: Mark lock_aligned variables 16-byte aligned on SMP
parisc: Mark jump_table naturally aligned
parisc: Mark altinstructions read-only and 32-bit aligned
parisc: Mark ex_table entries 32-bit aligned in uaccess.h
parisc: Mark ex_table entries 32-bit aligned in assembly.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 microcode fixes from Ingo Molnar:
"Fix/enhance x86 microcode version reporting: fix the bootup log spam,
and remove the driver version announcement to avoid version confusion
when distros backport fixes"
* tag 'x86-urgent-2023-11-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Rework early revisions reporting
x86/microcode: Remove the driver announcement and version
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 perf event fix from Ingo Molnar:
"Fix a bug in the Intel hybrid CPUs hardware-capabilities enumeration
code resulting in non-working events on those platforms"
* tag 'perf-urgent-2023-11-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Correct incorrect 'or' operation for PMU capabilities
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"Fix lockdep block chain corruption resulting in KASAN warnings"
* tag 'locking-urgent-2023-11-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Fix block chain corruption
|
|
Pull smb client fixes from Steve French:
- use after free fix in releasing multichannel interfaces
- fixes for special file types (report char, block, FIFOs properly when
created e.g. by NFS to Windows)
- fixes for reporting various special file types and symlinks properly
when using SMB1
* tag '6.7-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: client: introduce cifs_sfu_make_node()
smb: client: set correct file type from NFS reparse points
smb: client: introduce ->parse_reparse_point()
smb: client: implement ->query_reparse_point() for SMB1
cifs: fix use after free for iface while disabling secondary channels
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY / Thunderbolt fixes from Greg KH:
"Here are a number of reverts, fixes, and new device ids for 6.7-rc3
for the USB, PHY, and Thunderbolt driver subsystems. Include in here
are:
- reverts of some PHY drivers that went into 6.7-rc1 that shouldn't
have been merged yet, the author is reworking them based on review
comments as they were using older apis that shouldn't be used
anymore for newer drivers
- small thunderbolt driver fixes for reported issues
- USB driver fixes for a variety of small issues in dwc3, typec,
xhci, and other smaller drivers.
- new device ids for usb-serial and onboard_usb_hub drivers.
All of these have been in linux-next with no reported issues"
* tag 'usb-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
USB: serial: option: add Luat Air72*U series products
USB: dwc3: qcom: fix ACPI platform device leak
USB: dwc3: qcom: fix software node leak on probe errors
USB: dwc3: qcom: fix resource leaks on probe deferral
USB: dwc3: qcom: simplify wakeup interrupt setup
USB: dwc3: qcom: fix wakeup after probe deferral
dt-bindings: usb: qcom,dwc3: fix example wakeup interrupt types
usb: misc: onboard-hub: add support for Microchip USB5744
dt-bindings: usb: microchip,usb5744: Add second supply
usb: misc: ljca: Fix enumeration error on Dell Latitude 9420
USB: serial: option: add Fibocom L7xx modules
USB: xhci-plat: fix legacy PHY double init
usb: typec: tipd: Supply also I2C driver data
usb: xhci-mtk: fix in-ep's start-split check failure
usb: dwc3: set the dma max_seg_size
usb: config: fix iteration issue in 'usb_get_bos_descriptor()'
usb: dwc3: add missing of_node_put and platform_device_put
USB: dwc2: write HCINT with INTMASK applied
usb: misc: ljca: Drop _ADR support to get ljca children devices
usb: cdnsp: Fix deadlock issue during using NCM gadget
...
|
|
Pull xfs fix from Chandan Babu:
- Validate quota records recovered from the log before writing them to
the disk.
* tag 'xfs-6.7-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: dquot recovery does not validate the recovered dquot
xfs: clean up dqblk extraction
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix "rodata=on" not disabling "rodata=full" on arm64
- Add arm64 make dependency between vmlinuz.efi and Image, leading to
occasional build failures previously (with parallel building)
- Add newline to the output formatting of the za-fork kselftest
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: add dependency between vmlinuz.efi and Image
kselftest/arm64: Fix output formatting for za-fork
arm64: mm: Fix "rodata=on" when CONFIG_RODATA_FULL_DEFAULT_ENABLED=y
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- A small cleanup patch for the Xen privcmd driver
- A fix for the swiotlb-xen driver which was missing the advertising of
the maximum mapping length
- A fix for Xen on Arm for a longstanding bug, which happened to occur
only recently: a structure in percpu memory crossed a page boundary,
which was rejected by the hypervisor
* tag 'for-linus-6.7a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/xen: fix xen_vcpu_info allocation alignment
xen: privcmd: Replace zero-length array with flex-array member and use __counted_by
swiotlb-xen: provide the "max_mapping_size" method
|
|
Enable GENERIC_BUG_RELATIVE_POINTERS which will store 32-bit relative
offsets to the bug address and the source file name instead of 64-bit
absolute addresses. This effectively reduces the size of the
bug_table[] array by half on 64-bit kernels.
Signed-off-by: Helge Deller <[email protected]>
|
|
Those return codes are only defined for the parisc architecture and
are leftovers from when we wanted to be HP-UX compatible.
They are not returned by any Linux kernel syscall but do trigger
problems with the glibc strerrorname_np() and strerror() functions as
reported in glibc issue #31080.
There is no need to keep them, so simply remove them.
Signed-off-by: Helge Deller <[email protected]>
Reported-by: Bruno Haible <[email protected]>
Closes: https://sourceware.org/bugzilla/show_bug.cgi?id=31080
Cc: [email protected]
|
|
Make sure that the __bug_table section gets 32- or 64-bit aligned,
depending if a 32- or 64-bit kernel is being built.
Mark it non-writeable and use .blockz instead of the .org assembler
directive to pad the struct.
Signed-off-by: Helge Deller <[email protected]>
Cc: [email protected] # v6.0+
|