| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
>From the RK3588 Technical Reference Manual, Part1,
section 6.19 PCIe3PHY_GRF Register Description:
"rxX_cmn_refclk_mode"
RX common reference clock mode for lane X. This mode should be enabled
only when the far-end and near-end devices are running with a common
reference clock.
The hardware reset value for this field is 0x1 (enabled).
Note that this register field is only available on RK3588, not on RK3568.
The link training either fails or is highly unstable (link state will jump
continuously between L0 and recovery) when this mode is enabled while
using an endpoint running in Separate Reference Clock with No SSC (SRNS)
mode or Separate Reference Clock with SSC (SRIS) mode.
(Which is usually the case when using a real SoC as endpoint, e.g. the
RK3588 PCIe controller can run in both Root Complex and Endpoint mode.)
Add support for the device tree property rockchip,rx-common-refclk-mode,
such that the PCIe PHY can be used in configurations where the Root
Complex and Endpoint are not using a common reference clock.
Signed-off-by: Niklas Cassel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
>From the RK3588 Technical Reference Manual, Part1,
section 6.19 PCIe3PHY_GRF Register Description:
"rxX_cmn_refclk_mode"
RX common reference clock mode for lane X. This mode should be enabled
only when the far-end and near-end devices are running with a common
reference clock.
The hardware reset value for this field is 0x1 (enabled).
Note that this register field is only available on RK3588, not on RK3568.
The link training either fails or is highly unstable (link state will jump
continuously between L0 and recovery) when this mode is enabled while
using an endpoint running in Separate Reference Clock with No SSC (SRNS)
mode or Separate Reference Clock with SSC (SRIS) mode.
(Which is usually the case when using a real SoC as endpoint, e.g. the
RK3588 PCIe controller can run in both Root Complex and Endpoint mode.)
Add a rockchip specific property to enable/disable the rxX_cmn_refclk_mode
per lane. (Since this PHY supports bifurcation.)
Signed-off-by: Niklas Cassel <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Sebastian Reichel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
This adds a new USBDP combo PHY with Samsung IP block driver.
The driver get lane mux and mapping info in 2 ways, supporting
DisplayPort alternate mode or parsing from DT. When parsing from DT,
the property "rockchip,dp-lane-mux" provide the DP mux and mapping
info. This is needed when the PHY is not used with TypeC Alt-Mode.
For example if the USB3 interface of the PHY is connected to a USB
Type A connector and the DP interface is connected to a DisplayPort
connector.
When do DP link training, need to set lane number, link rate, swing,
and pre-emphasis via PHY configure interface.
Co-developed-by: Heiko Stuebner <[email protected]>
Signed-off-by: Heiko Stuebner <[email protected]>
Co-developed-by: Zhang Yubing <[email protected]>
Signed-off-by: Zhang Yubing <[email protected]>
Co-developed-by: Frank Wang <[email protected]>
Signed-off-by: Frank Wang <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add device tree binding document for Rockchip USBDP Combo PHY
with Samsung IP block.
Co-developed-by: Frank Wang <[email protected]>
Signed-off-by: Frank Wang <[email protected]>
Reviewed-by: Conor Dooley <[email protected]>
Reviewed-by: Heiko Stuebner <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add driver for MediaTek's XFI T-PHY which can be found in the MT7988
SoC. The XFI T-PHY is a 10 Gigabit/s Ethernet SerDes PHY with muxes on
the internal side to be used with either USXGMII PCS or LynxI PCS,
depending on the selected PHY interface mode.
The PHY can operates only in PHY_MODE_ETHERNET, the submode is one of
PHY_INTERFACE_MODE_* corresponding to the supported modes:
* USXGMII \
* 10GBase-R }- USXGMII PCS - XGDM \
* 5GBase-R / \
}- Ethernet MAC
* 2500Base-X \ /
* 1000Base-X }- LynxI PCS - GDM /
* Cisco SGMII (MAC side) /
I chose the name XFI T-PHY because names of functions dealing with the
phy in the vendor driver are prefixed "xfi_pextp_".
The register space used by the phy is called "pextp" in the vendor
sources, which could be read as "_P_CI _ex_press _T_-_P_hy", and that
is quite misleading as this phy isn't used for anything related to
PCIe, so I wanted to find a better name.
XFI is still somehow related (as in: you would find the relevant
places using grep in the vendor driver when looking for that) and the
term seemed to at least somehow be aligned with the function of that
phy: Dealing with (up to) 10 Gbit/s Ethernet serialized differential
signals.
In order to work-around a performance issue present on the first of
two XFI T-PHYs found in MT7988, special tuning is applied which can
be selected by adding the 'mediatek,usxgmii-performance-errata'
property to the device tree node, similar to how the vendor driver is
doing that too.
There is no documentation for most registers used for the
analog/tuning part, however, most of the registers have been partially
reverse-engineered from MediaTek's SDK implementation (see links, an
opaque sequence of 32-bit register writes) and descriptions for all
relevant digital registers and bits such as resets and muxes have been
supplied by MediaTek.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/b72d6cba92bf9e29fb035c03052fa1e86664a25b/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_sgmii.c
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/dec96a1d9b82cdcda4a56453fd0b453d4cab4b85/21.02/files/target/linux/mediatek/files-5.4/drivers/net/ethernet/mediatek/mtk_eth_soc.c
Signed-off-by: Daniel Golle <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Jacob Keller <[email protected]>
Link: https://lore.kernel.org/r/8719c82634df7e8e984f1a608be3ba2f2d494fb4.1712625857.git.daniel@makrotopia.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add bindings for the MediaTek XFI Ethernet SerDes T-PHY found in the
MediaTek MT7988 SoC which can operate at various interfaces modes:
via USXGMII PCS:
* USXGMII
* 10GBase-R
* 5GBase-R
via LynxI SGMII PCS:
* 2500Base-X
* 1000Base-X
* Cisco SGMII (MAC side)
Signed-off-by: Daniel Golle <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Jacob Keller <[email protected]>
Link: https://lore.kernel.org/r/da5498096f71a40ca1eac4124b7bb601c82396fb.1712625857.git.daniel@makrotopia.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Update the SM8650 UFS PHY init tables to support Gear 4 and Gear 5
using the overlays setup (only supported Gear 5 before), and sync
back with the latest Qualcomm recommended values.
The new recommended values allow a solid 50% bump in sequential
read/write benchmarks on the SM8650 QRD & HDK reference boards.
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/20240410-topic-sm8650-upstream-ufs-g5-v1-1-5527c44b37e6@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
This brings rockchip,pcie3-phy changes into next which incoming patches
are dependent on
|
|
According to the 'qcom,ipq5332-usb-hsphy.yaml' schema, the 5V
supply regulator must be defined via the 'vdd-supply' property.
The driver however requests for the 'vdda-phy' regulator which
results in the following message when the driver is probed on
a IPQ5018 based board with a device tree matching to the schema:
qcom-m31usb-phy 5b000.phy: supply vdda-phy not found, using dummy regulator
qcom-m31usb-phy 5b000.phy: Registered M31 USB phy
This means that the regulator specified in the device tree never
gets enabled.
Change the driver to use the 'vdd' name for the regulator as per
defined in the schema in order to ensure that the corresponding
regulator gets enabled.
Fixes: 08e49af50701 ("phy: qcom: Introduce M31 USB PHY driver")
Reviewed-by: Varadarajan Narayanan <[email protected]>
Signed-off-by: Gabor Juhos <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The register base that was used to write to the QSERDES_DP_PHY_MODE
register was 'dp_dp_phy' before commit 815891eee668 ("phy:
qcom-qmp-combo: Introduce orientation variable"). There isn't any
explanation in the commit why this is changed, so I suspect it was an
oversight or happened while being extracted from some other series.
Oddly the value being 0x4c or 0x5c doesn't seem to matter for me, so I
suspect this is dead code, but that can be fixed in another patch. It's
not good to write to the wrong register space, and maybe some other
version of this phy relies on this.
Cc: Douglas Anderson <[email protected]>
Cc: Abhinav Kumar <[email protected]>
Cc: Dmitry Baryshkov <[email protected]>
Cc: Neil Armstrong <[email protected]>
Cc: Abel Vesa <[email protected]>
Cc: Steev Klimaszewski <[email protected]>
Cc: Johan Hovold <[email protected]>
Cc: Bjorn Andersson <[email protected]>
Cc: [email protected] # 6.5
Fixes: 815891eee668 ("phy: qcom-qmp-combo: Introduce orientation variable")
Signed-off-by: Stephen Boyd <[email protected]>
Reviewed-by: Abhinav Kumar <[email protected]>
Reviewed-by: Bjorn Andersson <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Commit ec17373aebd0 ("phy: qcom: qmp-combo: extract common function to
setup clocks") changed the offset that is used to write to
DP_PHY_VCO_DIV from QSERDES_V3_DP_PHY_VCO_DIV to
QSERDES_V4_DP_PHY_VCO_DIV. Unfortunately, this offset is different
between v3 and v4 phys:
#define QSERDES_V3_DP_PHY_VCO_DIV 0x064
#define QSERDES_V4_DP_PHY_VCO_DIV 0x070
meaning that we write the wrong register on v3 phys now. Add another
generic register to 'regs' and use it here instead of a version specific
define to fix this.
This was discovered after Abhinav looked over register dumps with me
from sc7180 Trogdor devices that started failing to light up the
external display with v6.6 based kernels. It turns out that some
monitors are very specific about their link clk frequency and if the
default power on reset value is still there the monitor will show a
blank screen or a garbled display. Other monitors are perfectly happy to
get a bad clock signal.
Cc: Douglas Anderson <[email protected]>
Cc: Abhinav Kumar <[email protected]>
Cc: Dmitry Baryshkov <[email protected]>
Fixes: ec17373aebd0 ("phy: qcom: qmp-combo: extract common function to setup clocks")
Signed-off-by: Stephen Boyd <[email protected]>
Reviewed-by: Abhinav Kumar <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The pcie1l0_sel and pcie1l1_sel bits in PCIESEL_CON configure the
mux for PCIe1L0 and PCIe1L1 to either the PIPE Combo PHYs or the
PCIe3 PHY. Thus this configuration interfers with the data-lanes
configuration done by the PCIe3 PHY.
RK3588 has three Combo PHYs. The first one has a dedicated PCIe
controller and is not affected by this. For the other two Combo
PHYs, there is one mux for each of them.
pcie1l0_sel selects if PCIe 1L0 is muxed to Combo PHY 1 when
bit is set to 0 or to the PCIe3 PHY when bit is set to 1.
pcie1l1_sel selects if PCIe 1L1 is muxed to Combo PHY 2 when
bit is set to 0 or to the PCIe3 PHY when bit is set to 1.
Currently the code always muxes 1L0 and 1L1 to the Combi PHYs
once one of them is being used in PCIe mode. This is obviously
wrong when at least one of the ports should be muxed to the
PCIe3 PHY.
Fix this by introducing Combo PHY identification and then only
setting up the required bit.
Fixes: a03c44277253 ("phy: rockchip: Add naneng combo phy support for RK3588")
Reported-by: Michal Tomek <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
Reviewed-by: Heiko Stuebner <[email protected]>
Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-3-9907136eeafd@kernel.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
Currently the PCIe v3 PHY driver only sets the pcie1ln_sel bits, but
does not clear them because of an incorrect write mask. This fixes up
the issue by using a newly introduced constant for the write mask.
While at it also introduces a proper GENMASK based constant for the
PCIE30_PHY_MODE.
Fixes: 2e9bffc4f713 ("phy: rockchip: Support PCIe v3")
Signed-off-by: Sebastian Reichel <[email protected]>
Reviewed-by: Heiko Stuebner <[email protected]>
Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-2-9907136eeafd@kernel.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
So far all RK3588 boards use fully aggregated PCIe. CM3588 is one
of the few boards using this feature and apparently it is broken.
The PHY offers the following mapping options:
port 0 lane 0 - always mapped to controller 0 (4L)
port 0 lane 1 - to controller 0 or 2 (1L0)
port 1 lane 0 - to controller 0 or 1 (2L)
port 1 lane 1 - to controller 0, 1 or 3 (1L1)
The data-lanes DT property maps these as follows:
0 = no controller (unsupported by the HW)
1 = 4L
2 = 2L
3 = 1L0
4 = 1L1
That allows the following configurations with first column being the
mainline data-lane mapping, second column being the downstream name,
third column being PCIE3PHY_GRF_CMN_CON0 and PHP_GRF_PCIESEL register
values and final column being the user visible lane setup:
<1 1 1 1> = AGGREG = [4 0] = x4 (aggregation)
<1 1 2 2> = NANBNB = [0 0] = x2 x2 (no bif.)
<1 3 2 2> = NANBBI = [1 1] = x2 x1x1 (bif. of port 0)
<1 1 2 4> = NABINB = [2 2] = x1x1 x2 (bif. of port 1)
<1 3 2 4> = NABIBI = [3 3] = x1x1 x1x1 (bif. of both ports)
The driver currently does not program PHP_GRF_PCIESEL correctly, which
is fixed by this patch. As a side-effect the new logic is much simpler
than the old logic.
Fixes: 2e9bffc4f713 ("phy: rockchip: Support PCIe v3")
Signed-off-by: Michal Tomek <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
Acked-by: Heiko Stuebner <[email protected]>
Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-1-9907136eeafd@kernel.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add the newly created ufs phy for GS101 to MAINTAINERS.
Signed-off-by: Peter Griffin <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add the m-phy tuning values for gs101 UFS phy and SoC callbacks
gs101_phy_wait_for_calibration() and gs101_phy_wait_for_cdr_lock().
Signed-off-by: Peter Griffin <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Some SoCs like gs101 don't fit in well with the existing pll lock and
clock data recovery (CDR) callback used by existing exynos platforms.
Allow SoCs to specifify and implement their own calibration and CDR
functions that can be called by the generic samsung phy code.
Signed-off-by: Peter Griffin <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
This allows us to obtain a PMU regmap that is created by the exynos-pmu
driver. Platforms such as gs101 require exynos-pmu created regmap to
issue SMC calls for PMU register accesses. Existing platforms still get
a MMIO regmap as before.
Signed-off-by: Peter Griffin <[email protected]>
Reviewed-by: André Draszik <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Update dt schema to include the gs101 ufs phy compatible.
Signed-off-by: Peter Griffin <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
QMP UFS PHY used in SC7180 requires 3 clocks:
* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC
This change obviously breaks the ABI, but it is inevitable since the
clock topology needs to be accurately described in the binding.
Signed-off-by: Danila Tikhonov <[email protected]>
Acked-by: Rob Herring <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Leaving AUX_PLL_REFCLK_SEL at its reset default of AUX_IN (PLL clock)
proves to be more stable on the i.MX 8M Mini.
Fixes: 1aa97b002258 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Richard Zhu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the phy_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <[email protected]>
Suggested-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: "Ricardo B. Marliere" <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock,
enable this second clock by setting the proper 20MHz hardware rate in
the Gen4x2 SM8[456]50 aux_clock_rate config fields.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-4-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock,
add the code to register it for PHYs configs that sets a aux_clock_rate.
In order to get the right clock, add qmp_pcie_clk_hw_get() which uses
the newly introduced QMP_PCIE_PIPE_CLK & QMP_PCIE_PHY_AUX_CLK clock
IDs and also supports the legacy bindings by returning the PIPE clock
when #clock-cells=0.
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-3-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock,
in order to expose it, split the current clock registering in two parts:
- CCF clock registering
- DT clock registering
Keep the of_clk_add_hw_provider/devm_add_action_or_reset to keep
compatibility with the legacy subnode bindings.
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-2-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
SM8[456]50 SoCs
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock named
"PHY_AUX_CLK" which is an input of the Global Clock Controller (GCC) which
is muxed & gated then returned to the PHY as an input.
Document the clock IDs to select the PIPE clock or the AUX clock,
also enforce a second clock-output-names and a #clock-cells value of 1
for the PCIe Gen4x2 PHY found in the SM8[456]50 SoCs.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-1-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
Replace hardcoded 'gbe_phy_init' array size by explicit one.
Fixes: 934337080c6c ("phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation")
Signed-off-by: Mikhail Kobuk <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
There is an out of bounds read access of 'gbe_phy_init_fix[fix_idx].addr'
every iteration after 'fix_idx' reaches 'ARRAY_SIZE(gbe_phy_init_fix)'.
Make sure 'gbe_phy_init[addr]' is used when all elements of
'gbe_phy_init_fix' array are handled.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 934337080c6c ("phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation")
Signed-off-by: Mikhail Kobuk <[email protected]>
Reviewed-by: Miquel Raynal <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <[email protected]>
Acked-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/57a3338a1cec683ac84d48e00dbf197e15ee5481.1709886922.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <[email protected]>
|
|
Several functions had "rochchip" instead of "rockchip" in their name.
Replace "rochchip" by "rockchip".
Signed-off-By: Rick Wertenbroek <[email protected]>
Reviewed-by: Heiko Stuebner <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The QMP USB3/DP PHY found in the SM8650 SoC requires a slightly
different Voltage Swing table for HBR/RBR link speeds.
Add a new hbr/rbr voltage switch table named "v6" used in a new
sm8650 qmp_phy_cfg struct replacing the sm8550 fallback used for
the sm8650 compatible.
Fixes: 80c1afe8c5fe ("phy: qcom: qmp-combo: add QMP USB3/DP PHY tables for SM8650")
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/20240226-topic-sm8650-upstream-combo-phy-swing-update-v1-1-08707ebca92a@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add the tables and constants for init sequences for UFS QMP phy found in
SM8475 SoC.
Signed-off-by: Danila Tikhonov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Document the QMP UFS PHY compatible for SM8475.
Signed-off-by: Danila Tikhonov <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Remove duplicate "return 0" in qmp_v4_configure_dp_phy()
Fixes: 186ad90aa49f ("phy: qcom: qmp-combo: reuse register layouts for even more registers")
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Reviewed-by: Abhinav Kumar <[email protected]>
Link: https://lore.kernel.org/r/20240228-topic-sm8x50-upstream-phy-combo-fix-duplicate-return-v1-1-60027a37cab1@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add v6 HW support by implementing the version ops. Add the X1E80100
compatible and match config as it is v6.
Signed-off-by: Abel Vesa <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
In order to support different HW versions move everything specific
to v4 into so-called version ops.
Signed-off-by: Abel Vesa <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The Qualcomm X1E80100 platform has multiple PHYs that can work in both
eDP or DP mode, so document their compatible.
Signed-off-by: Abel Vesa <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
The SMB2360 PMICs contain the same repeater as the PM8550B, but requiring
different settings, so add dedicated compatible for SMB2360.
Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: Abel Vesa <[email protected]>
Link: https://lore.kernel.org/r/20240220-phy-qualcomm-eusb2-repeater-smb2360-v2-2-213338ca1d5f@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add a dt-bindings compatible string for the Qualcomm's SMB2360 PMIC.
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Abel Vesa <[email protected]>
Link: https://lore.kernel.org/r/20240220-phy-qualcomm-eusb2-repeater-smb2360-v2-1-213338ca1d5f@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
phy_dp_modes_6.10
This contains the dp submode definition and associated qcom driver change
|
|
Future platforms should not use different compatibles to differentiate
between eDP and DP mode. Instead, they should use a single compatible as
the IP block is the same. It will be the job of the controller to set the
submode of the PHY accordingly.
The existing platforms will remain with separate compatibles for each
mode.
Signed-off-by: Abel Vesa <[email protected]>
Link: https://lore.kernel.org/r/20240324-x1e80100-phy-edp-compatible-refactor-v5-2-a0db5f3150bc@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
In some cases, a DP PHY needs to be configured to work in eDP mode.
So add submodes for both DP and eDP so they can be used by the
controllers for specifying the mode the PHY should be configured in.
Signed-off-by: Abel Vesa <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Link: https://lore.kernel.org/r/20240324-x1e80100-phy-edp-compatible-refactor-v5-1-a0db5f3150bc@linaro.org
Signed-off-by: Vinod Koul <[email protected]>
|
|
This adds the driver for the Samsung HDMI PHY found on the
i.MX8MP SoC. Based on downstream implementation from
Sandor Yu <[email protected]>. According to the TRM, the PHY
receives parallel data from the link and serializes it. It
also sets the PLL clock needed for the TX serializer.
Tested-by: Luca Ceresoli <[email protected]>
Tested-by: Richard Leitner <[email protected]>
Co-developed-by: Marco Felsch <[email protected]>
Signed-off-by: Marco Felsch <[email protected]>
Signed-off-by: Lucas Stach <[email protected]>
Tested-by: Alexander Stein <[email protected]>
Tested-by: Frieder Schrempf <[email protected]> # Kontron BL
Signed-off-by: Adam Ford <[email protected]>
Tested-by: Marek Vasut <[email protected]>
Tested-by: Luca Ceresoli <[email protected]>
Tested-by: Tommaso Merciai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Add a DT binding for the HDMI PHY found on the i.MX8MP SoC.
Signed-off-by: Lucas Stach <[email protected]>
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Luca Ceresoli <[email protected]>
Tested-by: Tommaso Merciai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- Fix logic that is supposed to prevent placement of the kernel image
below LOAD_PHYSICAL_ADDR
- Use the firmware stack in the EFI stub when running in mixed mode
- Clear BSS only once when using mixed mode
- Check efi.get_variable() function pointer for NULL before trying to
call it
* tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: fix panic in kdump kernel
x86/efistub: Don't clear BSS twice in mixed mode
x86/efistub: Call mixed mode boot services on the firmware's stack
efi/libstub: fix efi_random_alloc() to allocate memory at alloc_min or higher address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- Ensure that the encryption mask at boot is properly propagated on
5-level page tables, otherwise the PGD entry is incorrectly set to
non-encrypted, which causes system crashes during boot.
- Undo the deferred 5-level page table setup as it cannot work with
memory encryption enabled.
- Prevent inconsistent XFD state on CPU hotplug, where the MSR is reset
to the default value but the cached variable is not, so subsequent
comparisons might yield the wrong result and as a consequence the
result prevents updating the MSR.
- Register the local APIC address only once in the MPPARSE enumeration
to prevent triggering the related WARN_ONs() in the APIC and topology
code.
- Handle the case where no APIC is found gracefully by registering a
fake APIC in the topology code. That makes all related topology
functions work correctly and does not affect the actual APIC driver
code at all.
- Don't evaluate logical IDs during early boot as the local APIC IDs
are not yet enumerated and the invoked function returns an error
code. Nothing requires the logical IDs before the final CPUID
enumeration takes place, which happens after the enumeration.
- Cure the fallout of the per CPU rework on UP which misplaced the
copying of boot_cpu_data to per CPU data so that the final update to
boot_cpu_data got lost which caused inconsistent state and boot
crashes.
- Use copy_from_kernel_nofault() in the kprobes setup as there is no
guarantee that the address can be safely accessed.
- Reorder struct members in struct saved_context to work around another
kmemleak false positive
- Remove the buggy code which tries to update the E820 kexec table for
setup_data as that is never passed to the kexec kernel.
- Update the resource control documentation to use the proper units.
- Fix a Kconfig warning observed with tinyconfig
* tag 'x86-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/64: Move 5-level paging global variable assignments back
x86/boot/64: Apply encryption mask to 5-level pagetable update
x86/cpu: Add model number for another Intel Arrow Lake mobile processor
x86/fpu: Keep xfd_state in sync with MSR_IA32_XFD
Documentation/x86: Document that resctrl bandwidth control units are MiB
x86/mpparse: Register APIC address only once
x86/topology: Handle the !APIC case gracefully
x86/topology: Don't evaluate logical IDs during early boot
x86/cpu: Ensure that CPU info updates are propagated on UP
kprobes/x86: Use copy_from_kernel_nofault() to read from unsafe address
x86/pm: Work around false positive kmemleak report in msr_build_context()
x86/kexec: Do not update E820 kexec table for setup_data
x86/config: Fix warning for 'make ARCH=x86_64 tinyconfig'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler doc clarification from Thomas Gleixner:
"A single update for the documentation of the base_slice_ns tunable to
clarify that any value which is less than the tick slice has no effect
because the scheduler tick is not guaranteed to happen within the set
time slice"
* tag 'sched-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/doc: Update documentation for base_slice_ns and CONFIG_HZ relation
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"This has a set of swiotlb alignment fixes for sometimes very long
standing bugs from Will. We've been discussion them for a while and
they should be solid now"
* tag 'dma-mapping-6.9-2024-03-24' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: Reinstate page-alignment for mappings >= PAGE_SIZE
iommu/dma: Force swiotlb_max_mapping_size on an untrusted device
swiotlb: Fix alignment checks when both allocation and DMA masks are present
swiotlb: Honour dma_alloc_coherent() alignment in swiotlb_alloc()
swiotlb: Enforce page alignment in swiotlb_alloc()
swiotlb: Fix double-allocation of slots due to broken alignment handling
|