| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
SCMI fix for v4.17
A single patch to ensure that the scmi device is not used for setting up
scmi handle after it's freed(fixes use after free).
* tag 'scmi-fixes-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Use after free in scmi_create_protocol_device()
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants for v4.17
This series of patches contains one BUG fix for trace if
CONFIG_DEBUG_PREEMPT is enabled and a regression fix for omap1 FIQ
handling on ams-delta. Then there's a dts fix for missing SoC
compatible on ti81xx board dts files that did matter until we added
the clkctrl clocks and without that some clocks are now not found.
Then there are two logicpd-som-lv specific dts fixes that fix
misconfigured pins for WLAN and audio. Turns out we had to revert
the third one because it caused another regression for USB.
* tag 'omap-for-v17/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "ARM: dts: logicpd-som-lv: Fix pinmux controller references"
ARM: dts: correct missing "compatible" entry for ti81xx SoCs
ARM: OMAP1: ams-delta: fix deferred_fiq handler
ARM: dts: logicpd-som-lv: Fix pinmux controller references
ARM: dts: logicpd-som-lv: Fix Audio Mute
ARM: dts: logicpd-som-lv: Fix WL127x Startup Issues
ARM: OMAP2+: powerdomain: use raw_smp_processor_id() for trace
Signed-off-by: Olof Johansson <[email protected]>
|
|
https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-basec SoCs Device Tree fixes for
4.17, please pull the following:
- Clement fixes in an incorrect trigger type for the ARM global timers
on the Cygnus platforms
* tag 'arm-soc/for-4.17/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: cygnus: fix irq type for arm global timer
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.linaro.org/people/jens.wiklander/linux-tee into fixes
Small fixes for tee subsystem
* Fixes for use-after-free via temporarily dropped reference
* Checks that passed shm references are consistent in offset/size
with regards to the shm object
* tag 'tee-drv-fixes-for-4.17' of git://git.linaro.org/people/jens.wiklander/linux-tee:
tee: check shm references are consistent in offset/size
tee: shm: fix use-after-free via temporarily dropped reference
Signed-off-by: Olof Johansson <[email protected]>
|
|
All interrupts from SoC internal modules are level triggered, so fix
incorrect trigger type for I2S1 device on Exynos5433 SoCs.
This fixes following kernel warning:
WARNING: CPU: 2 PID: 1 at drivers/irqchip/irq-gic.c:1016 gic_irq_domain_translate+0xb0/0xb8
Modules linked in:
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.16.0-rc7-next-20180329 #646
Hardware name: Samsung TM2 board (DT)
pstate: 20000005 (nzCv daif -PAN -UAO)
pc : gic_irq_domain_translate+0xb0/0xb8
lr : irq_create_fwspec_mapping+0x64/0x328
sp : ffff0000098b38d0
...
Call trace:
gic_irq_domain_translate+0xb0/0xb8
irq_create_of_mapping+0x78/0xa0
of_irq_get+0x6c/0xa0
of_irq_to_resource+0x38/0x108
of_irq_to_resource_table+0x50/0x78
of_device_alloc+0x118/0x1b8
of_platform_device_create_pdata+0x54/0xe0
of_platform_bus_create+0x118/0x340
of_platform_bus_create+0x17c/0x340
of_platform_populate+0x74/0xd8
of_platform_default_populate_init+0xb0/0xcc
do_one_initcall+0x50/0x158
kernel_init_freeable+0x184/0x22c
kernel_init+0x10/0x108
ret_from_fork+0x10/0x18
---[ end trace 6decb2b3078d73f0 ]---
Fixes: d8d579c316e8 ("ARM: dts: exynos: Add I2S1 device node to exynos5433")
Signed-off-by: Marek Szyprowski <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into fixes
ARM: tegra: Device tree fixes for v4.17
This contains a single revert for a patch that was merged in v4.17-rc1
and that turns out to cause a regression on some boards. Further, the
original issue that the patch was supposed to fix seems to have
disappeared.
* tag 'tegra-for-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra20: Revert "Fix ULPI regression on Tegra20"
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
DaVinci fixes for v4.17
* W=1 warning fixes in device-tree files
* GPIO look-up fixes for legacy boot on several platforms
* tag 'davinci-fixes-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: fix GPIO lookup for I2C
ARM: davinci: board-dm355-evm: fix broken networking
ARM: davinci: board-omapl138-hawk: fix GPIO numbers for MMC/SD lookup
ARM: davinci: board-da850-evm: fix GPIO lookup for MMC/SD
ARM: davinci: board-da830-evm: fix GPIO lookup for MMC/SD
ARM: dts: da850: fix W=1 warnings with pinmux node
ARM: dts: da850-lcdk: add unit name for memory node
ARM: dts: da850: get rid of skeleton.dtsi
Signed-off-by: Olof Johansson <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v4.17
Fix LVDS output on Gen2 boards
Laurent Pincart says "This patch series fixes LVDS output support on the
Lager, Koelsh, Porter and Gose boards that broke in v4.17-rc1 due to the
combination of the R-Car DU LVDS driver rework and the DT move of all
on-SoC peripherals to a /soc node.
We could handle the problem in the R-Car DU LVDS DT backward compatibility
code, but that fix would only be used for v4.17 as in v4.18 the Gen2 DT
will move to the new LVDS DT bindings. I thus propose merging these three
patches in v4.17 already to fix the problem as this is the simplest
solution."
* tag 'renesas-fixes-for-v4.17' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7793: Convert to new LVDS DT bindings
ARM: dts: r8a7791: Convert to new LVDS DT bindings
ARM: dts: r8a7790: Convert to new LVDS DT bindings
Signed-off-by: Olof Johansson <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into fixes
UniPhier ARM SoC fixes for v4.17
- Fix input delay parameter of eMMC PHY
- Weaken drive-strength of ethernet PHY pins of LD20 reference board
* tag 'uniphier-fixes-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: stabilize ethernet of LD20 reference board
arm64: dts: uniphier: fix input delay value for legacy mode of eMMC
Signed-off-by: Olof Johansson <[email protected]>
|
|
Signed-off-by: Claudio Scordino <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Cc: Jonathan Corbet <[email protected]>
Cc: Juri Lelli <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Luca Abeni <[email protected]>
Cc: Mike Galbraith <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
introduce available_idle_cpu()
In the following commit:
247f2f6f3c70 ("sched/core: Don't schedule threads on pre-empted vCPUs")
... we distinguish between idle_cpu() when the vCPU is not running for
scheduling threads.
However, the idle_cpu() function is used in other places for
actually checking whether the state of the CPU is idle or not.
Hence split the use of that function based on the desired return value,
by introducing the available_idle_cpu() function.
This fixes a (slight) regression in that initial vCPU commit, because
some code paths (like the load-balancer) don't care and shouldn't care
if the vCPU is preempted or not, they just want to know if there's any
tasks on the CPU.
Signed-off-by: Rohit Jain <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Mike Galbraith <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
kbuild bot reported against an intermediate RT patch that the build
fails with:
> In file included from include/linux/completion.h:12:0,
> from include/linux/rcupdate_wait.h:10,
> from kernel/rcu/srcutiny.c:27:
> kernel/rcu/srcutiny.c: In function 'srcu_drive_gp':
> >> include/linux/swait.h:172:7: error: implicit declaration of function '___wait_is_interruptible'; did you mean '__swait_event_interruptible'?
> if (___wait_is_interruptible(state) && __int) { \
That error vanishes a few patches later (in the RT queue) because wait.h
is then pulled in by other means. It does not seem to surface on !RT.
I think that swait should include a header file for a function/macro
(___wait_is_interruptible()) it is using.
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Mike Galbraith <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Threads share an address space and each can change the protections of the
same address space to trap NUMA faults. This is redundant and potentially
counter-productive as any thread doing the update will suffice. Potentially
only one thread is required but that thread may be idle or it may not have
any locality concerns and pick an unsuitable scan rate.
This patch uses independent scan period but they are staggered based on
the number of address space users when the thread is created. The intent
is that threads will avoid scanning at the same time and have a chance
to adapt their scan rate later if necessary. This reduces the total scan
activity early in the lifetime of the threads.
The different in headline performance across a range of machines and
workloads is marginal but the system CPU usage is reduced as well as overall
scan activity. The following is the time reported by NAS Parallel Benchmark
using unbound openmp threads and a D size class:
4.17.0-rc1 4.17.0-rc1
vanilla stagger-v1r1
Time bt.D 442.77 ( 0.00%) 419.70 ( 5.21%)
Time cg.D 171.90 ( 0.00%) 180.85 ( -5.21%)
Time ep.D 33.10 ( 0.00%) 32.90 ( 0.60%)
Time is.D 9.59 ( 0.00%) 9.42 ( 1.77%)
Time lu.D 306.75 ( 0.00%) 304.65 ( 0.68%)
Time mg.D 54.56 ( 0.00%) 52.38 ( 4.00%)
Time sp.D 1020.03 ( 0.00%) 903.77 ( 11.40%)
Time ua.D 400.58 ( 0.00%) 386.49 ( 3.52%)
Note it's not a universal win but we have no prior knowledge of which
thread matters but the number of threads created often exceeds the size
of the node when the threads are not bound. However, there is a reducation
of overall system CPU usage:
4.17.0-rc1 4.17.0-rc1
vanilla stagger-v1r1
sys-time-bt.D 48.78 ( 0.00%) 48.22 ( 1.15%)
sys-time-cg.D 25.31 ( 0.00%) 26.63 ( -5.22%)
sys-time-ep.D 1.65 ( 0.00%) 0.62 ( 62.42%)
sys-time-is.D 40.05 ( 0.00%) 24.45 ( 38.95%)
sys-time-lu.D 37.55 ( 0.00%) 29.02 ( 22.72%)
sys-time-mg.D 47.52 ( 0.00%) 34.92 ( 26.52%)
sys-time-sp.D 119.01 ( 0.00%) 109.05 ( 8.37%)
sys-time-ua.D 51.52 ( 0.00%) 45.13 ( 12.40%)
NUMA scan activity is also reduced:
NUMA alloc local 1042828 1342670
NUMA base PTE updates 140481138 93577468
NUMA huge PMD updates 272171 180766
NUMA page range updates 279832690 186129660
NUMA hint faults 1395972 1193897
NUMA hint local faults 877925 855053
NUMA hint local percent 62 71
NUMA pages migrated 12057909 9158023
Similar observations are made for other thread-intensive workloads. System
CPU usage is lower even though the headline gains in performance tend to be
small. For example, specjbb 2005 shows almost no difference in performance
but scan activity is reduced by a third on a 4-socket box. I didn't find
a workload (thread intensive or otherwise) that suffered badly.
Signed-off-by: Mel Gorman <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Matt Fleming <[email protected]>
Cc: Mike Galbraith <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Signed-off-by: Ingo Molnar <[email protected]>
|
|
definition for mixed mode
Mixed mode allows a kernel built for x86_64 to interact with 32-bit
EFI firmware, but requires us to define all struct definitions carefully
when it comes to pointer sizes.
'struct efi_pci_io_protocol_32' currently uses a 'void *' for the
'romimage' field, which will be interpreted as a 64-bit field
on such kernels, potentially resulting in bogus memory references
and subsequent crashes.
Tested-by: Hans de Goede <[email protected]>
Signed-off-by: Ard Biesheuvel <[email protected]>
Cc: <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Matt Fleming <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2018-05-14
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix nfp to allow zero-length BPF capabilities, meaning the nfp
capability parsing loop will otherwise exit early if the last
capability is zero length and therefore driver will fail to probe
with an error such as:
nfp: BPF capabilities left after parsing, parsed:92 total length:100
nfp: invalid BPF capabilities at offset:92
Fix from Jakub.
2) libbpf's bpf_object__open() may return IS_ERR_OR_NULL() and not
just an error. Fix libbpf's bpf_prog_load_xattr() to handle that
case as well, also from Jakub.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Fix handling of simultaneous open TCP connection in conntrack,
from Jozsef Kadlecsik.
2) Insufficient sanitify check of xtables extension names, from
Florian Westphal.
3) Skip unnecessary synchronize_rcu() call when transaction log
is already empty, from Florian Westphal.
4) Incorrect destination mac validation in ebt_stp, from Stephen
Hemminger.
5) xtables module reference counter leak in nft_compat, from
Florian Westphal.
6) Incorrect connection reference counting logic in IPVS
one-packet scheduler, from Julian Anastasov.
7) Wrong stats for 32-bits CPU in IPVS, also from Julian.
8) Calm down sparse error in netfilter core, also from Florian.
9) Use nla_strlcpy to fix compilation warning in nfnetlink_acct
and nfnetlink_cthelper, again from Florian.
10) Missing module alias in icmp and icmp6 xtables extensions,
from Florian Westphal.
11) Base chain statistics in nf_tables may be unset/null, from Florian.
12) Fix handling of large matchinfo size in nft_compat, this includes
one preparation for before this fix. From Florian.
13) Fix bogus EBUSY error when deleting chains due to incorrect reference
counting from the preparation phase of the two-phase commit protocol.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Rebooting while qedr is loaded with a VLAN interface present
results in unregister_netdevice waiting for the usage count
to become free.
The fix is that rdma devices should be removed before unregistering
the netdevice, to assure all references to ndev are decreased.
Fixes: cee9fbd8e2e9 ("qede: Add qedr framework")
Signed-off-by: Ariel Elior <[email protected]>
Signed-off-by: Michal Kalderon <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This driver supports EISA devices in addition to PCI devices, and relied
on the legacy behavior of the pci_dma* shims to pass on a NULL pointer
to the DMA API, and the DMA API being able to handle that. When the
NULL forwarding broke the EISA support got broken. Fix this by converting
to the DMA API instead of the legacy PCI shims.
Fixes: 4167b2ad ("PCI: Remove NULL device handling from PCI DMA API")
Reported-by: tedheadster <[email protected]>
Tested-by: tedheadster <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Packet sockets allow construction of packets shorter than
dev->hard_header_len to accommodate protocols with variable length
link layer headers. These packets are padded to dev->hard_header_len,
because some device drivers interpret that as a minimum packet size.
packet_snd reserves dev->hard_header_len bytes on allocation.
SOCK_DGRAM sockets call skb_push in dev_hard_header() to ensure that
link layer headers are stored in the reserved range. SOCK_RAW sockets
do the same in tpacket_snd, but not in packet_snd.
Syzbot was able to send a zero byte packet to a device with massive
116B link layer header, causing padding to cross over into skb_shinfo.
Fix this by writing from the start of the llheader reserved range also
in the case of packet_snd/SOCK_RAW.
Update skb_set_network_header to the new offset. This also corrects
it for SOCK_DGRAM, where it incorrectly double counted reserve due to
the skb_push in dev_hard_header.
Fixes: 9ed988cd5915 ("packet: validate variable length ll headers")
Reported-by: [email protected]
Signed-off-by: Willem de Bruijn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
|
|
Currently the -EBUSY error return path is not free'ing resources
allocated earlier, leaving a memory leak. Fix this by exiting via the
error exit label err5 that performs the necessary resource clean
up.
Detected by CoverityScan, CID#1432975 ("Resource leak")
Fixes: 9744a6fcefcb ("netfilter: nf_tables: check if same extensions are set when adding elements")
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Workaround for the sake of BPF compilation which utilizes kernel
headers, but clang does not support ASM GOTO and fails the build.
Fixes: d0266046ad54 ("x86: Remove FAST_FEATURE_TESTS")
Suggested-by: Thomas Gleixner <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
"VFS: don't keep disconnected dentries on d_anon" had a non-trivial
side-effect - d_unhashed() now returns true for those dentries,
making d_find_alias() skip them altogether. For most of its callers
that's fine - we really want a connected alias there. However,
there is a codepath where we relied upon picking such aliases
if nothing else could be found - selinux delayed initialization
of contexts for inodes on already mounted filesystems used to
rely upon that.
Cc: [email protected] # f1ee616214cb "VFS: don't keep disconnected dentries on d_anon"
Signed-off-by: Al Viro <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/pti updates from Thomas Gleixner:
"A mixed bag of fixes and updates for the ghosts which are hunting us.
The scheduler fixes have been pulled into that branch to avoid
conflicts.
- A set of fixes to address a khread_parkme() race which caused lost
wakeups and loss of state.
- A deadlock fix for stop_machine() solved by moving the wakeups
outside of the stopper_lock held region.
- A set of Spectre V1 array access restrictions. The possible
problematic spots were discuvered by Dan Carpenters new checks in
smatch.
- Removal of an unused file which was forgotten when the rest of that
functionality was removed"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Remove unused file
perf/x86/cstate: Fix possible Spectre-v1 indexing for pkg_msr
perf/x86/msr: Fix possible Spectre-v1 indexing in the MSR driver
perf/x86: Fix possible Spectre-v1 indexing for x86_pmu::event_map()
perf/x86: Fix possible Spectre-v1 indexing for hw_perf_event cache_*
perf/core: Fix possible Spectre-v1 indexing for ->aux_pages[]
sched/autogroup: Fix possible Spectre-v1 indexing for sched_prio_to_weight[]
sched/core: Fix possible Spectre-v1 indexing for sched_prio_to_weight[]
sched/core: Introduce set_special_state()
kthread, sched/wait: Fix kthread_parkme() completion issue
kthread, sched/wait: Fix kthread_parkme() wait-loop
sched/fair: Fix the update of blocked load when newly idle
stop_machine, sched: Fix migrate_swap() vs. active_balance() deadlock
|
|
Since MOV SS and POP SS instructions will delay the exceptions until the
next instruction is executed, single-stepping on it by uprobes must be
prohibited.
uprobe already rejects probing on POP SS (0x1f), but allows probing on MOV
SS (0x8e and reg == 2). This checks the target instruction and if it is
MOV SS or POP SS, returns -ENOTSUPP to reject probing.
Signed-off-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: Oleg Nesterov <[email protected]>
Cc: Ricardo Neri <[email protected]>
Cc: Francis Deslauriers <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: Steven Rostedt <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: "H . Peter Anvin" <[email protected]>
Cc: Yonghong Song <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: "David S . Miller" <[email protected]>
Link: https://lkml.kernel.org/r/152587072544.17316.5950935243917346341.stgit@devbox
|
|
Since MOV SS and POP SS instructions will delay the exceptions until the
next instruction is executed, single-stepping on it by kprobes must be
prohibited.
However, kprobes usually executes those instructions directly on trampoline
buffer (a.k.a. kprobe-booster), except for the kprobes which has
post_handler. Thus if kprobe user probes MOV SS with post_handler, it will
do single-stepping on the MOV SS.
This means it is safe that if it is used via ftrace or perf/bpf since those
don't use the post_handler.
Anyway, since the stack switching is a rare case, it is safer just
rejecting kprobes on such instructions.
Signed-off-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Ricardo Neri <[email protected]>
Cc: Francis Deslauriers <[email protected]>
Cc: Oleg Nesterov <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: Steven Rostedt <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: "H . Peter Anvin" <[email protected]>
Cc: Yonghong Song <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: "David S . Miller" <[email protected]>
Link: https://lkml.kernel.org/r/152587069574.17316.3311695234863248641.stgit@devbox
|
|
>From ff82bedd3e12f0d3353282054ae48c3bd8c72012 Mon Sep 17 00:00:00 2001
From: Tetsuo Handa <[email protected]>
Date: Wed, 9 May 2018 12:12:39 +0900
Subject: [PATCH v3] x86/kexec: avoid double free_page() upon do_kexec_load() failure.
syzbot is reporting crashes after memory allocation failure inside
do_kexec_load() [1]. This is because free_transition_pgtable() is called
by both init_transition_pgtable() and machine_kexec_cleanup() when memory
allocation failed inside init_transition_pgtable().
Regarding 32bit code, machine_kexec_free_page_tables() is called by both
machine_kexec_alloc_page_tables() and machine_kexec_cleanup() when memory
allocation failed inside machine_kexec_alloc_page_tables().
Fix this by leaving the error handling to machine_kexec_cleanup()
(and optionally setting NULL after free_page()).
[1] https://syzkaller.appspot.com/bug?id=91e52396168cf2bdd572fe1e1bc0bc645c1c6b40
Fixes: f5deb79679af6eb4 ("x86: kexec: Use one page table in x86_64 machine_kexec")
Fixes: 92be3d6bdf2cb349 ("kexec/i386: allocate page table pages dynamically")
Reported-by: syzbot <[email protected]>
Signed-off-by: Tetsuo Handa <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: Baoquan He <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: Huang Ying <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: H. Peter Anvin <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"Revert the new NUMA aware placement approach which turned out to
create more problems than it solved"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "sched/numa: Delay retrying placement for automatic NUMA balance after wake_affine()"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling fixes from Thomas Gleixner:
"Another small set of perf tooling fixes and updates:
- Revert "perf pmu: Fix pmu events parsing rule", as it broke Intel
PT event description parsing (Arnaldo Carvalho de Melo)
- Sync x86's cpufeatures.h and kvm UAPI headers with the kernel
sources, suppressing the ABI drift warnings (Arnaldo Carvalho de
Melo)
- Remove duplicated entry for westmereep-dp in Intel's mapfile.csv
(William Cohen)
- Fix typo in 'perf bench numa' options description (Yisheng Xie)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "perf pmu: Fix pmu events parsing rule"
tools headers kvm: Sync ARM UAPI headers with the kernel sources
tools headers kvm: Sync uapi/linux/kvm.h with the kernel sources
tools headers: Sync x86 cpufeatures.h with the kernel sources
perf vendor events intel: Remove duplicated entry for westmereep-dp in mapfile.csv
perf bench numa: Fix typo in options
|
|
Pull dma-mapping fix from Christoph Hellwig:
"Just one little fix from Jean to avoid a harmless but very annoying
warning, especially for the drm code"
* tag 'dma-mapping-4.17-5' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: silent unwanted warning "buffer is full"
|
|
This adds support for the P950ER, which has the same required fixup as
the P950HR, but has a different PCI ID.
Signed-off-by: Jeremy Soller <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Currently it's not possible to set volume lower than 26% (it just mutes).
Also fixes this warning:
Warning! Unlikely big volume range (=9472), cval->res is probably wrong.
[13] FU [PCM Playback Volume] ch = 2, val = -9473/-1/1
, and volume works fine for full range.
Signed-off-by: Federico Cuello <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The SMN (System Management Network) on Family 17h AMD CPUs is also accessed
from other drivers, specifically EDAC. Accessing it directly is racy.
On top of that, accessing the SMN through root bridge 00:00 is wrong on
multi-die CPUs and may result in reading the temperature from the wrong
die. Use available API functions to fix the problem.
For this to work, add dependency on AMD_NB. Also change the Raven Ridge
PCI device ID to point to Data Fabric Function 3, since this ID is used
by the API functions to find the CPU node.
Cc: [email protected] # v4.16+
Tested-by: Gabriel Craciunescu <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Add Raven Ridge root bridge and data fabric PCI IDs.
This is required for amd_pci_dev_to_node_id() and amd_smn_read().
Cc: [email protected] # v4.16+
Tested-by: Gabriel Craciunescu <[email protected]>
Acked-by: Thomas Gleixner <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
|
|
Power-saving is causing loud plops on the Lenovo C50 All in one, add it
to the blacklist.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1572975
Signed-off-by: Hans de Goede <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
In snd_ctl_elem_add_compat(), the fields of the struct 'data' need to be
copied from the corresponding fields of the struct 'data32' in userspace.
This is achieved by invoking copy_from_user() and get_user() functions. The
problem here is that the 'type' field is copied twice. One is by
copy_from_user() and one is by get_user(). Given that the 'type' field is
not used between the two copies, the second copy is *completely* redundant
and should be removed for better performance and cleanup. Also, these two
copies can cause inconsistent data: as the struct 'data32' resides in
userspace and a malicious userspace process can race to change the 'type'
field between the two copies to cause inconsistent data. Depending on how
the data is used in the future, such an inconsistency may cause potential
security risks.
For above reasons, we should take out the second copy.
Signed-off-by: Wenwen Wang <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Pull cifs fixes from Steve French:
"Some small SMB3 fixes for 4.17-rc5, some for stable"
* tag '4.17-rc4-SMB3-Fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb3: directory sync should not return an error
cifs: smb2ops: Fix listxattr() when there are no EAs
cifs: smbd: Enable signing with smbdirect
cifs: Allocate validate negotiation request through kmalloc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal fixes from Zhang Rui:
- fix NULL pointer dereference on module load/probe for int3403_thermal
driver
- fix an emergency shutdown issue on exynos thermal driver
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: exynos: Propagate error value from tmu_read()
thermal: exynos: Reading temperature makes sense only when TMU is turned on
thermal: int3403_thermal: Fix NULL pointer deref on module load / probe
|
|
Pull block fixes from Jens Axboe:
"Just a few NVMe fixes this round - one fixing a use-after-free, one
fixes the return value after controller reset, and the last one fixes
an issue where some drives will spuriously EIO. We should get these
into 4.17"
* tag 'for-linus-20180511' of git://git.kernel.dk/linux-block:
nvme: add quirk to force medium priority for SQ creation
nvme: Fix sync controller reset return
nvme: fix use-after-free in nvme_free_ns_head
|
|
If DMA_ATTR_NO_WARN is passed to swiotlb_alloc_buffer(), it should be
passed further down to swiotlb_tbl_map_single(). Otherwise we escape
half of the warnings but still log the other half.
This is one of the multiple causes of spurious warnings reported at:
https://bugs.freedesktop.org/show_bug.cgi?id=104082
Signed-off-by: Jean Delvare <[email protected]>
Fixes: 0176adb00406 ("swiotlb: refactor coherent buffer allocation")
Cc: Christoph Hellwig <[email protected]>
Cc: Christian König <[email protected]>
Cc: Michel Dänzer <[email protected]>
Cc: Takashi Iwai <[email protected]>
Cc: [email protected] # v4.16
|
|
Fixes: 7bb4d366c ("x86/bugs: Make cpu_show_common() static")
Fixes: 24f7fc83b ("x86/bugs: Provide boot parameters for the spec_store_bypass_disable mitigation")
Signed-off-by: Konrad Rzeszutek Wilk <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
after wake_affine()"
This reverts commit 7347fc87dfe6b7315e74310ee1243dc222c68086.
Srikar Dronamra pointed out that while the commit in question did show
a performance improvement on ppc64, it did so at the cost of disabling
active CPU migration by automatic NUMA balancing which was not the intent.
The issue was that a serious flaw in the logic failed to ever active balance
if SD_WAKE_AFFINE was disabled on scheduler domains. Even when it's enabled,
the logic is still bizarre and against the original intent.
Investigation showed that fixing the patch in either the way he suggested,
using the correct comparison for jiffies values or introducing a new
numa_migrate_deferred variable in task_struct all perform similarly to a
revert with a mix of gains and losses depending on the workload, machine
and socket count.
The original intent of the commit was to handle a problem whereby
wake_affine, idle balancing and automatic NUMA balancing disagree on the
appropriate placement for a task. This was particularly true for cases where
a single task was a massive waker of tasks but where wake_wide logic did
not apply. This was particularly noticeable when a futex (a barrier) woke
all worker threads and tried pulling the wakees to the waker nodes. In that
specific case, it could be handled by tuning MPI or openMP appropriately,
but the behavior is not illogical and was worth attempting to fix. However,
the approach was wrong. Given that we're at rc4 and a fix is not obvious,
it's better to play safe, revert this commit and retry later.
Signed-off-by: Mel Gorman <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Srikar Dronamraju <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <[email protected]>:
rbtree: include rcu.h
scripts/faddr2line: fix error when addr2line output contains discriminator
ocfs2: take inode cluster lock before moving reflinked inode from orphan dir
mm, oom: fix concurrent munlock and oom reaper unmap, v3
mm: migrate: fix double call of radix_tree_replace_slot()
proc/kcore: don't bounds check against address 0
mm: don't show nr_indirectly_reclaimable in /proc/vmstat
mm: sections are not offlined during memory hotremove
z3fold: fix reclaim lock-ups
init: fix false positives in W+X checking
lib/find_bit_benchmark.c: avoid soft lockup in test_find_first_bit()
KASAN: prohibit KASAN+STRUCTLEAK combination
MAINTAINERS: update Shuah's email address
|
|
Since commit c1adf20052d8 ("Introduce rb_replace_node_rcu()")
rbtree_augmented.h uses RCU related data structures but does not include
the header file. It works as long as it gets somehow included before
that and fails otherwise.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Sebastian Andrzej Siewior <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Cc: David Howells <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
When addr2line output contains discriminator, the current awk script
cannot parse it. This patch fixes it by extracting key words using
regex which is more reliable.
$ scripts/faddr2line vmlinux tlb_flush_mmu_free+0x26
tlb_flush_mmu_free+0x26/0x50:
tlb_flush_mmu_free at mm/memory.c:258 (discriminator 3)
scripts/faddr2line: eval: line 173: unexpected EOF while looking for matching `)'
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 6870c0165feaa5 ("scripts/faddr2line: show the code context")
Signed-off-by: Changbin Du <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Philippe Ombredanne <[email protected]>
Cc: NeilBrown <[email protected]>
Cc: Richard Weinberger <[email protected]>
Cc: Kate Stewart <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
While reflinking an inode, we create a new inode in orphan directory,
then take EX lock on it, reflink the original inode to orphan inode and
release EX lock. Once the lock is released another node could request
it in EX mode from ocfs2_recover_orphans() which causes downconvert of
the lock, on this node, to NL mode.
Later we attempt to initialize security acl for the orphan inode and
move it to the reflink destination. However, while doing this we dont
take EX lock on the inode. This could potentially cause problems
because we could be starting transaction, accessing journal and
modifying metadata of the inode while holding NL lock and with another
node holding EX lock on the inode.
Fix this by taking orphan inode cluster lock in EX mode before
initializing security and moving orphan inode to reflink destination.
Use the __tracker variant while taking inode lock to avoid recursive
locking in the ocfs2_init_security_and_acl() call chain.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ashish Samant <[email protected]>
Reviewed-by: Joseph Qi <[email protected]>
Reviewed-by: Junxiao Bi <[email protected]>
Acked-by: Jun Piao <[email protected]>
Cc: Mark Fasheh <[email protected]>
Cc: Joel Becker <[email protected]>
Cc: Changwei Ge <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Since exit_mmap() is done without the protection of mm->mmap_sem, it is
possible for the oom reaper to concurrently operate on an mm until
MMF_OOM_SKIP is set.
This allows munlock_vma_pages_all() to concurrently run while the oom
reaper is operating on a vma. Since munlock_vma_pages_range() depends
on clearing VM_LOCKED from vm_flags before actually doing the munlock to
determine if any other vmas are locking the same memory, the check for
VM_LOCKED in the oom reaper is racy.
This is especially noticeable on architectures such as powerpc where
clearing a huge pmd requires serialize_against_pte_lookup(). If the pmd
is zapped by the oom reaper during follow_page_mask() after the check
for pmd_none() is bypassed, this ends up deferencing a NULL ptl or a
kernel oops.
Fix this by manually freeing all possible memory from the mm before
doing the munlock and then setting MMF_OOM_SKIP. The oom reaper can not
run on the mm anymore so the munlock is safe to do in exit_mmap(). It
also matches the logic that the oom reaper currently uses for
determining when to set MMF_OOM_SKIP itself, so there's no new risk of
excessive oom killing.
This issue fixes CVE-2018-1000200.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: 212925802454 ("mm: oom: let oom_reap_task and exit_mmap run concurrently")
Signed-off-by: David Rientjes <[email protected]>
Suggested-by: Tetsuo Handa <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: <[email protected]> [4.14+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
radix_tree_replace_slot() is called twice for head page, it's obviously
a bug. Let's fix it.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: e71769ae5260 ("mm: enable thp migration for shmem thp")
Signed-off-by: Naoya Horiguchi <[email protected]>
Reported-by: Matthew Wilcox <[email protected]>
Reviewed-by: Andrew Morton <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: "Kirill A. Shutemov" <[email protected]>
Cc: Zi Yan <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The existing kcore code checks for bad addresses against __va(0) with
the assumption that this is the lowest address on the system. This may
not hold true on some systems (e.g. arm64) and produce overflows and
crashes. Switch to using other functions to validate the address range.
It's currently only seen on arm64 and it's not clear if anyone wants to
use that particular combination on a stable release. So this is not
urgent for stable.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Laura Abbott <[email protected]>
Tested-by: Dave Anderson <[email protected]>
Cc: Kees Cook <[email protected]>
Cc: Ard Biesheuvel <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Alexey Dobriyan <[email protected]>a
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|