aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2021-12-15tty: n_hdlc: make n_hdlc_tty_wakeup() asynchronousTetsuo Handa1-1/+22
syzbot is reporting that an unprivileged user who logged in from tty console can crash the system using a reproducer shown below [1], for n_hdlc_tty_wakeup() is synchronously calling n_hdlc_send_frames(). ---------- #include <sys/ioctl.h> #include <unistd.h> int main(int argc, char *argv[]) { const int disc = 0xd; ioctl(1, TIOCSETD, &disc); while (1) { ioctl(1, TCXONC, 0); write(1, "", 1); ioctl(1, TCXONC, 1); /* Kernel panic - not syncing: scheduling while atomic */ } } ---------- Linus suspected that "struct tty_ldisc"->ops->write_wakeup() must not sleep, and Jiri confirmed it from include/linux/tty_ldisc.h. Thus, defer n_hdlc_send_frames() from n_hdlc_tty_wakeup() to a WQ context like net/nfc/nci/uart.c does. Link: https://syzkaller.appspot.com/bug?extid=5f47a8cea6a12b77a876 [1] Reported-by: syzbot <[email protected]> Cc: stable <[email protected]> Analyzed-by: Fabio M. De Francesco <[email protected]> Suggested-by: Linus Torvalds <[email protected]> Confirmed-by: Jiri Slaby <[email protected]> Reviewed-by: Fabio M. De Francesco <[email protected]> Signed-off-by: Tetsuo Handa <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-15ixgbe: set X550 MDIO speed before talking to PHYCyril Novikov1-0/+3
The MDIO bus speed must be initialized before talking to the PHY the first time in order to avoid talking to it using a speed that the PHY doesn't support. This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined with the 10Gb network results in a 24MHz MDIO speed, which is apparently too fast for the connected PHY. PHY register reads over MDIO bus return garbage, leading to initialization failure. Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using the following setup: * Use an Atom C3000 family system with at least one X552 LAN on the SoC * Disable PXE or other BIOS network initialization if possible (the interface must not be initialized before Linux boots) * Connect a live 10Gb Ethernet cable to an X550 port * Power cycle (not reset, doesn't always work) the system and boot Linux * Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17 Fixes: e84db7272798 ("ixgbe: Introduce function to control MDIO speed") Signed-off-by: Cyril Novikov <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2021-12-15dm integrity: fix data corruption due to improper use of bvec_kmap_localMike Snitzer1-1/+1
Commit 25058d1c725c ("dm integrity: use bvec_kmap_local in __journal_read_write") didn't account for __journal_read_write() later adding the biovec's bv_offset. As such using bvec_kmap_local() caused the start of the biovec to be skipped. Trivial test that illustrates data corruption: # integritysetup format /dev/pmem0 # integritysetup open /dev/pmem0 integrityroot # mkfs.xfs /dev/mapper/integrityroot ... bad magic number bad magic number Metadata corruption detected at xfs_sb block 0x0/0x1000 libxfs_writebufr: write verifer failed on xfs_sb bno 0x0/0x1000 releasing dirty buffer (bulk) to free list! Fix this by using kmap_local_page() instead of bvec_kmap_local() in __journal_read_write(). Fixes: 25058d1c725c ("dm integrity: use bvec_kmap_local in __journal_read_write") Reported-by: Tony Asleson <[email protected]> Reviewed-by: Heinz Mauelshagen <[email protected]> Signed-off-by: Mike Snitzer <[email protected]>
2021-12-15ixgbe: Document how to enable NBASE-T supportRobert Schlabbach2-0/+20
Commit a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support") introduced suppression of the advertisement of NBASE-T speeds by default, according to Todd Fujinaka to accommodate customers with network switches which could not cope with advertised NBASE-T speeds, as posted in the E1000-devel mailing list: https://sourceforge.net/p/e1000/mailman/message/37106269/ However, the suppression was not documented at all, nor was how to enable NBASE-T support. Properly document the NBASE-T suppression and how to enable NBASE-T support. Fixes: a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support") Reported-by: Robert Schlabbach <[email protected]> Signed-off-by: Robert Schlabbach <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2021-12-15igc: Fix typo in i225 LTR functionsSasha Neftin1-1/+1
The LTR maximum value was incorrectly written using the scale from the LTR minimum value. This would cause incorrect values to be sent, in cases where the initial calculation lead to different min/max scales. Fixes: 707abf069548 ("igc: Add initial LTR support") Suggested-by: Dima Ruinskiy <[email protected]> Signed-off-by: Sasha Neftin <[email protected]> Tested-by: Nechama Kraus <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2021-12-15igbvf: fix double free in `igbvf_probe`Letu Ren1-0/+1
In `igbvf_probe`, if register_netdev() fails, the program will go to label err_hw_init, and then to label err_ioremap. In free_netdev() which is just below label err_ioremap, there is `list_for_each_entry_safe` and `netif_napi_del` which aims to delete all entries in `dev->napi_list`. The program has added an entry `adapter->rx_ring->napi` which is added by `netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has been freed below label err_hw_init. So this a UAF. In terms of how to patch the problem, we can refer to igbvf_remove() and delete the entry before `adapter->rx_ring`. The KASAN logs are as follows: [ 35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450 [ 35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366 [ 35.128360] [ 35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14 [ 35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 35.131749] Call Trace: [ 35.132199] dump_stack_lvl+0x59/0x7b [ 35.132865] print_address_description+0x7c/0x3b0 [ 35.133707] ? free_netdev+0x1fd/0x450 [ 35.134378] __kasan_report+0x160/0x1c0 [ 35.135063] ? free_netdev+0x1fd/0x450 [ 35.135738] kasan_report+0x4b/0x70 [ 35.136367] free_netdev+0x1fd/0x450 [ 35.137006] igbvf_probe+0x121d/0x1a10 [igbvf] [ 35.137808] ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf] [ 35.138751] local_pci_probe+0x13c/0x1f0 [ 35.139461] pci_device_probe+0x37e/0x6c0 [ 35.165526] [ 35.165806] Allocated by task 366: [ 35.166414] ____kasan_kmalloc+0xc4/0xf0 [ 35.167117] foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf] [ 35.168078] igbvf_probe+0x9c5/0x1a10 [igbvf] [ 35.168866] local_pci_probe+0x13c/0x1f0 [ 35.169565] pci_device_probe+0x37e/0x6c0 [ 35.179713] [ 35.179993] Freed by task 366: [ 35.180539] kasan_set_track+0x4c/0x80 [ 35.181211] kasan_set_free_info+0x1f/0x40 [ 35.181942] ____kasan_slab_free+0x103/0x140 [ 35.182703] kfree+0xe3/0x250 [ 35.183239] igbvf_probe+0x1173/0x1a10 [igbvf] [ 35.184040] local_pci_probe+0x13c/0x1f0 Fixes: d4e0fe01a38a0 (igbvf: add new driver to support 82576 virtual functions) Reported-by: Zheyu Ma <[email protected]> Signed-off-by: Letu Ren <[email protected]> Tested-by: Konrad Jankowski <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2021-12-15igb: Fix removal of unicast MAC filters of VFsKaren Sornek1-14/+14
Move checking condition of VF MAC filter before clearing or adding MAC filter to VF to prevent potential blackout caused by removal of necessary and working VF's MAC filter. Fixes: 1b8b062a99dc ("igb: add VF trust infrastructure") Signed-off-by: Karen Sornek <[email protected]> Tested-by: Konrad Jankowski <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2021-12-15Merge tag 'ceph-for-5.16-rc6' of git://github.com/ceph/ceph-clientLinus Torvalds3-14/+25
Pull ceph fixes from Ilya Dryomov: "An SGID directory handling fix (marked for stable), a metrics accounting fix and two fixups to appease static checkers" * tag 'ceph-for-5.16-rc6' of git://github.com/ceph/ceph-client: ceph: fix up non-directory creation in SGID directories ceph: initialize pathlen variable in reconnect_caps_cb ceph: initialize i_size variable in ceph_sync_read ceph: fix duplicate increment of opened_inodes metric
2021-12-15Merge tag 's390-5.16-5' of ↵Linus Torvalds6-11/+44
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Heiko Carstens: - Add missing handling of R_390_PLT32DBL relocation type in arch_kexec_apply_relocations_add(). Clang and the upcoming gcc 11.3 generate such relocation entries, which our relocation code silently ignores, and which finally will result in an endless loop within the purgatory code in case of kexec. - Add proper handling of errors and print error messages when applying relocations - Fix duplicate tracking of irq nesting level in entry code - Let recordmcount.pl also look for jgnop mnemonic. Starting with binutils 2.37 objdump emits a jgnop mnemonic instead of brcl, which breaks mcount location detection. This is only a problem if used with compilers older than gcc 9, since with gcc 9 and newer compilers recordmcount.pl is not used anymore. - Remove preempt_disable()/preempt_enable() pair in kprobe_ftrace_handler() which was done for all architectures except for s390. - Update defconfig * tag 's390-5.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: recordmcount.pl: look for jgnop instruction as well as bcrl on s390 s390/entry: fix duplicate tracking of irq nesting level s390: enable switchdev support in defconfig s390/kexec: handle R_390_PLT32DBL rela in arch_kexec_apply_relocations_add() s390/ftrace: remove preempt_disable()/preempt_enable() pair s390/kexec_file: fix error handling when applying relocations s390/kexec_file: print some more error messages
2021-12-15Merge tag 'hyperv-fixes-signed-20211214' of ↵Linus Torvalds1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux Pull hyperv fix from Wei Liu: "Build fix from Randy Dunlap" * tag 'hyperv-fixes-signed-20211214' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: hv: utils: add PTP_1588_CLOCK to Kconfig to fix build
2021-12-15audit: improve robustness of the audit queue handlingPaul Moore1-11/+10
If the audit daemon were ever to get stuck in a stopped state the kernel's kauditd_thread() could get blocked attempting to send audit records to the userspace audit daemon. With the kernel thread blocked it is possible that the audit queue could grow unbounded as certain audit record generating events must be exempt from the queue limits else the system enter a deadlock state. This patch resolves this problem by lowering the kernel thread's socket sending timeout from MAX_SCHEDULE_TIMEOUT to HZ/10 and tweaks the kauditd_send_queue() function to better manage the various audit queues when connection problems occur between the kernel and the audit daemon. With this patch, the backlog may temporarily grow beyond the defined limits when the audit daemon is stopped and the system is under heavy audit pressure, but kauditd_thread() will continue to make progress and drain the queues as it would for other connection problems. For example, with the audit daemon put into a stopped state and the system configured to audit every syscall it was still possible to shutdown the system without a kernel panic, deadlock, etc.; granted, the system was slow to shutdown but that is to be expected given the extreme pressure of recording every syscall. The timeout value of HZ/10 was chosen primarily through experimentation and this developer's "gut feeling". There is likely no one perfect value, but as this scenario is limited in scope (root privileges would be needed to send SIGSTOP to the audit daemon), it is likely not worth exposing this as a tunable at present. This can always be done at a later date if it proves necessary. Cc: [email protected] Fixes: 5b52330bbfe63 ("audit: fix auditd/kernel connection state tracking") Reported-by: Gaosheng Cui <[email protected]> Tested-by: Gaosheng Cui <[email protected]> Reviewed-by: Richard Guy Briggs <[email protected]> Signed-off-by: Paul Moore <[email protected]>
2021-12-15usb: dwc2: fix STM ID/VBUS detection startup delay in dwc2_driver_probeAmelie Delaunay1-0/+3
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies on sensing comparators. This detection needs time to stabilize. A delay was already applied in dwc2_resume() when reactivating the detection, but it wasn't done in dwc2_probe(). This patch adds delay after enabling STM ID/VBUS detection. Then, ID state is good when initializing gadget and host, and avoid to get a wrong Connector ID Status Change interrupt. Fixes: a415083a11cc ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS") Cc: stable <[email protected]> Acked-by: Minas Harutyunyan <[email protected]> Signed-off-by: Amelie Delaunay <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-15USB: gadget: bRequestType is a bitfield, not a enumGreg Kroah-Hartman3-9/+9
Szymon rightly pointed out that the previous check for the endpoint direction in bRequestType was not looking at only the bit involved, but rather the whole value. Normally this is ok, but for some request types, bits other than bit 8 could be set and the check for the endpoint length could not stall correctly. Fix that up by only checking the single bit. Fixes: 153a2d7e3350 ("USB: gadget: detect too-big endpoint 0 requests") Cc: Felipe Balbi <[email protected]> Reported-by: Szymon Heidrich <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-12-15soc/tegra: fuse: Fix bitwise vs. logical OR warningNathan Chancellor2-2/+2
A new warning in clang points out two instances where boolean expressions are being used with a bitwise OR instead of logical OR: drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical] reg = tegra_fuse_read_spare(i) | ^~~~~~~~~~~~~~~~~~~~~~~~~~ || drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical] reg = tegra_fuse_read_spare(i) | ^~~~~~~~~~~~~~~~~~~~~~~~~~ || drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning 2 warnings generated. The motivation for the warning is that logical operations short circuit while bitwise operations do not. In this instance, tegra_fuse_read_spare() is not semantically returning a boolean, it is returning a bit value. Use u32 for its return type so that it can be used with either bitwise or boolean operators without any warnings. Fixes: 25cd5a391478 ("ARM: tegra: Add speedo-based process identification") Link: https://github.com/ClangBuiltLinux/linux/issues/1488 Suggested-by: Michał Mirosław <[email protected]> Signed-off-by: Nathan Chancellor <[email protected]> Reviewed-by: Nick Desaulniers <[email protected]> Signed-off-by: Thierry Reding <[email protected]>
2021-12-15btrfs: fix missing blkdev_put() call in btrfs_scan_one_device()Shin'ichiro Kawasaki1-2/+4
The function btrfs_scan_one_device() calls blkdev_get_by_path() and blkdev_put() to get and release its target block device. However, when btrfs_sb_log_location_bdev() fails, blkdev_put() is not called and the block device is left without clean up. This triggered failure of fstests generic/085. Fix the failure path of btrfs_sb_log_location_bdev() to call blkdev_put(). Fixes: 12659251ca5df ("btrfs: implement log-structured superblock for ZONED mode") CC: [email protected] # 5.15+ Reviewed-by: Nikolay Borisov <[email protected]> Signed-off-by: Shin'ichiro Kawasaki <[email protected]> Reviewed-by: David Sterba <[email protected]> Signed-off-by: David Sterba <[email protected]>
2021-12-15btrfs: fix warning when freeing leaf after subvolume creation failureFilipe Manana1-3/+4
When creating a subvolume, at ioctl.c:create_subvol(), if we fail to insert the root item for the new subvolume into the root tree, we can trigger the following warning: [78961.741046] WARNING: CPU: 0 PID: 4079814 at fs/btrfs/extent-tree.c:3357 btrfs_free_tree_block+0x2af/0x310 [btrfs] [78961.743344] Modules linked in: [78961.749440] dm_snapshot dm_thin_pool (...) [78961.773648] CPU: 0 PID: 4079814 Comm: fsstress Not tainted 5.16.0-rc4-btrfs-next-108 #1 [78961.775198] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [78961.777266] RIP: 0010:btrfs_free_tree_block+0x2af/0x310 [btrfs] [78961.778398] Code: 17 00 48 85 (...) [78961.781067] RSP: 0018:ffffaa4001657b28 EFLAGS: 00010202 [78961.781877] RAX: 0000000000000213 RBX: ffff897f8a796910 RCX: 0000000000000000 [78961.782780] RDX: 0000000000000000 RSI: 0000000011004000 RDI: 00000000ffffffff [78961.783764] RBP: ffff8981f490e800 R08: 0000000000000001 R09: 0000000000000000 [78961.784740] R10: 0000000000000000 R11: 0000000000000001 R12: ffff897fc963fcc8 [78961.785665] R13: 0000000000000001 R14: ffff898063548000 R15: ffff898063548000 [78961.786620] FS: 00007f31283c6b80(0000) GS:ffff8982ace00000(0000) knlGS:0000000000000000 [78961.787717] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [78961.788598] CR2: 00007f31285c3000 CR3: 000000023fcc8003 CR4: 0000000000370ef0 [78961.789568] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [78961.790585] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [78961.791684] Call Trace: [78961.792082] <TASK> [78961.792359] create_subvol+0x5d1/0x9a0 [btrfs] [78961.793054] btrfs_mksubvol+0x447/0x4c0 [btrfs] [78961.794009] ? preempt_count_add+0x49/0xa0 [78961.794705] __btrfs_ioctl_snap_create+0x123/0x190 [btrfs] [78961.795712] ? _copy_from_user+0x66/0xa0 [78961.796382] btrfs_ioctl_snap_create_v2+0xbb/0x140 [btrfs] [78961.797392] btrfs_ioctl+0xd1e/0x35c0 [btrfs] [78961.798172] ? __slab_free+0x10a/0x360 [78961.798820] ? rcu_read_lock_sched_held+0x12/0x60 [78961.799664] ? lock_release+0x223/0x4a0 [78961.800321] ? lock_acquired+0x19f/0x420 [78961.800992] ? rcu_read_lock_sched_held+0x12/0x60 [78961.801796] ? trace_hardirqs_on+0x1b/0xe0 [78961.802495] ? _raw_spin_unlock_irqrestore+0x3e/0x60 [78961.803358] ? kmem_cache_free+0x321/0x3c0 [78961.804071] ? __x64_sys_ioctl+0x83/0xb0 [78961.804711] __x64_sys_ioctl+0x83/0xb0 [78961.805348] do_syscall_64+0x3b/0xc0 [78961.805969] entry_SYSCALL_64_after_hwframe+0x44/0xae [78961.806830] RIP: 0033:0x7f31284bc957 [78961.807517] Code: 3c 1c 48 f7 d8 (...) This is because we are calling btrfs_free_tree_block() on an extent buffer that is dirty. Fix that by cleaning the extent buffer, with btrfs_clean_tree_block(), before freeing it. This was triggered by test case generic/475 from fstests. Fixes: 67addf29004c5b ("btrfs: fix metadata extent leak after failure to create subvolume") CC: [email protected] # 4.4+ Reviewed-by: Nikolay Borisov <[email protected]> Signed-off-by: Filipe Manana <[email protected]> Signed-off-by: David Sterba <[email protected]>
2021-12-15btrfs: fix invalid delayed ref after subvolume creation failureFilipe Manana6-22/+31
When creating a subvolume, at ioctl.c:create_subvol(), if we fail to insert the new root's root item into the root tree, we are freeing the metadata extent we reserved for the new root to prevent a metadata extent leak, as we don't abort the transaction at that point (since there is nothing at that point that is irreversible). However we allocated the metadata extent for the new root which we are creating for the new subvolume, so its delayed reference refers to the ID of this new root. But when we free the metadata extent we pass the root of the subvolume where the new subvolume is located to btrfs_free_tree_block() - this is incorrect because this will generate a delayed reference that refers to the ID of the parent subvolume's root, and not to ID of the new root. This results in a failure when running delayed references that leads to a transaction abort and a trace like the following: [3868.738042] RIP: 0010:__btrfs_free_extent+0x709/0x950 [btrfs] [3868.739857] Code: 68 0f 85 e6 fb ff (...) [3868.742963] RSP: 0018:ffffb0e9045cf910 EFLAGS: 00010246 [3868.743908] RAX: 00000000fffffffe RBX: 00000000fffffffe RCX: 0000000000000002 [3868.745312] RDX: 00000000fffffffe RSI: 0000000000000002 RDI: ffff90b0cd793b88 [3868.746643] RBP: 000000000e5d8000 R08: 0000000000000000 R09: ffff90b0cd793b88 [3868.747979] R10: 0000000000000002 R11: 00014ded97944d68 R12: 0000000000000000 [3868.749373] R13: ffff90b09afe4a28 R14: 0000000000000000 R15: ffff90b0cd793b88 [3868.750725] FS: 00007f281c4a8b80(0000) GS:ffff90b3ada00000(0000) knlGS:0000000000000000 [3868.752275] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [3868.753515] CR2: 00007f281c6a5000 CR3: 0000000108a42006 CR4: 0000000000370ee0 [3868.754869] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [3868.756228] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [3868.757803] Call Trace: [3868.758281] <TASK> [3868.758655] ? btrfs_merge_delayed_refs+0x178/0x1c0 [btrfs] [3868.759827] __btrfs_run_delayed_refs+0x2b1/0x1250 [btrfs] [3868.761047] btrfs_run_delayed_refs+0x86/0x210 [btrfs] [3868.762069] ? lock_acquired+0x19f/0x420 [3868.762829] btrfs_commit_transaction+0x69/0xb20 [btrfs] [3868.763860] ? _raw_spin_unlock+0x29/0x40 [3868.764614] ? btrfs_block_rsv_release+0x1c2/0x1e0 [btrfs] [3868.765870] create_subvol+0x1d8/0x9a0 [btrfs] [3868.766766] btrfs_mksubvol+0x447/0x4c0 [btrfs] [3868.767669] ? preempt_count_add+0x49/0xa0 [3868.768444] __btrfs_ioctl_snap_create+0x123/0x190 [btrfs] [3868.769639] ? _copy_from_user+0x66/0xa0 [3868.770391] btrfs_ioctl_snap_create_v2+0xbb/0x140 [btrfs] [3868.771495] btrfs_ioctl+0xd1e/0x35c0 [btrfs] [3868.772364] ? __slab_free+0x10a/0x360 [3868.773198] ? rcu_read_lock_sched_held+0x12/0x60 [3868.774121] ? lock_release+0x223/0x4a0 [3868.774863] ? lock_acquired+0x19f/0x420 [3868.775634] ? rcu_read_lock_sched_held+0x12/0x60 [3868.776530] ? trace_hardirqs_on+0x1b/0xe0 [3868.777373] ? _raw_spin_unlock_irqrestore+0x3e/0x60 [3868.778280] ? kmem_cache_free+0x321/0x3c0 [3868.779011] ? __x64_sys_ioctl+0x83/0xb0 [3868.779718] __x64_sys_ioctl+0x83/0xb0 [3868.780387] do_syscall_64+0x3b/0xc0 [3868.781059] entry_SYSCALL_64_after_hwframe+0x44/0xae [3868.781953] RIP: 0033:0x7f281c59e957 [3868.782585] Code: 3c 1c 48 f7 d8 4c (...) [3868.785867] RSP: 002b:00007ffe1f83e2b8 EFLAGS: 00000202 ORIG_RAX: 0000000000000010 [3868.787198] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f281c59e957 [3868.788450] RDX: 00007ffe1f83e2c0 RSI: 0000000050009418 RDI: 0000000000000003 [3868.789748] RBP: 00007ffe1f83f300 R08: 0000000000000000 R09: 00007ffe1f83fe36 [3868.791214] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000003 [3868.792468] R13: 0000000000000003 R14: 00007ffe1f83e2c0 R15: 00000000000003cc [3868.793765] </TASK> [3868.794037] irq event stamp: 0 [3868.794548] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [3868.795670] hardirqs last disabled at (0): [<ffffffff98294214>] copy_process+0x934/0x2040 [3868.797086] softirqs last enabled at (0): [<ffffffff98294214>] copy_process+0x934/0x2040 [3868.798309] softirqs last disabled at (0): [<0000000000000000>] 0x0 [3868.799284] ---[ end trace be24c7002fe27747 ]--- [3868.799928] BTRFS info (device dm-0): leaf 241188864 gen 1268 total ptrs 214 free space 469 owner 2 [3868.801133] BTRFS info (device dm-0): refs 2 lock_owner 225627 current 225627 [3868.802056] item 0 key (237436928 169 0) itemoff 16250 itemsize 33 [3868.802863] extent refs 1 gen 1265 flags 2 [3868.803447] ref#0: tree block backref root 1610 (...) [3869.064354] item 114 key (241008640 169 0) itemoff 12488 itemsize 33 [3869.065421] extent refs 1 gen 1268 flags 2 [3869.066115] ref#0: tree block backref root 1689 (...) [3869.403834] BTRFS error (device dm-0): unable to find ref byte nr 241008640 parent 0 root 1622 owner 0 offset 0 [3869.405641] BTRFS: error (device dm-0) in __btrfs_free_extent:3076: errno=-2 No such entry [3869.407138] BTRFS: error (device dm-0) in btrfs_run_delayed_refs:2159: errno=-2 No such entry Fix this by passing the new subvolume's root ID to btrfs_free_tree_block(). This requires changing the root argument of btrfs_free_tree_block() from struct btrfs_root * to a u64, since at this point during the subvolume creation we have not yet created the struct btrfs_root for the new subvolume, and btrfs_free_tree_block() only needs a root ID and nothing else from a struct btrfs_root. This was triggered by test case generic/475 from fstests. Fixes: 67addf29004c5b ("btrfs: fix metadata extent leak after failure to create subvolume") CC: [email protected] # 4.4+ Reviewed-by: Nikolay Borisov <[email protected]> Signed-off-by: Filipe Manana <[email protected]> Signed-off-by: David Sterba <[email protected]>
2021-12-15btrfs: check WRITE_ERR when trying to read an extent bufferJosef Bacik1-0/+8
Filipe reported a hang when we have errors on btrfs. This turned out to be a side-effect of my fix c2e39305299f01 ("btrfs: clear extent buffer uptodate when we fail to write it") which made it so we clear EXTENT_BUFFER_UPTODATE on an eb when we fail to write it out. Below is a paste of Filipe's analysis he got from using drgn to debug the hang """ btree readahead code calls read_extent_buffer_pages(), sets ->io_pages to a value while writeback of all pages has not yet completed: --> writeback for the first 3 pages finishes, we clear EXTENT_BUFFER_UPTODATE from eb on the first page when we get an error. --> at this point eb->io_pages is 1 and we cleared Uptodate bit from the first 3 pages --> read_extent_buffer_pages() does not see EXTENT_BUFFER_UPTODATE() so it continues, it's able to lock the pages since we obviously don't hold the pages locked during writeback --> read_extent_buffer_pages() then computes 'num_reads' as 3, and sets eb->io_pages to 3, since only the first page does not have Uptodate bit set at this point --> writeback for the remaining page completes, we ended decrementing eb->io_pages by 1, resulting in eb->io_pages == 2, and therefore never calling end_extent_buffer_writeback(), so EXTENT_BUFFER_WRITEBACK remains in the eb's flags --> of course, when the read bio completes, it doesn't and shouldn't call end_extent_buffer_writeback() --> we should clear EXTENT_BUFFER_UPTODATE only after all pages of the eb finished writeback? or maybe make the read pages code wait for writeback of all pages of the eb to complete before checking which pages need to be read, touch ->io_pages, submit read bio, etc writeback bit never cleared means we can hang when aborting a transaction, at: btrfs_cleanup_one_transaction() btrfs_destroy_marked_extents() wait_on_extent_buffer_writeback() """ This is a problem because our writes are not synchronized with reads in any way. We clear the UPTODATE flag and then we can easily come in and try to read the EB while we're still waiting on other bio's to complete. We have two options here, we could lock all the pages, and then check to see if eb->io_pages != 0 to know if we've already got an outstanding write on the eb. Or we can simply check to see if we have WRITE_ERR set on this extent buffer. We set this bit _before_ we clear UPTODATE, so if the read gets triggered because we aren't UPTODATE because of a write error we're guaranteed to have WRITE_ERR set, and in this case we can simply return -EIO. This will fix the reported hang. Reported-by: Filipe Manana <[email protected]> Fixes: c2e39305299f01 ("btrfs: clear extent buffer uptodate when we fail to write it") CC: [email protected] # 5.4+ Reviewed-by: Filipe Manana <[email protected]> Signed-off-by: Josef Bacik <[email protected]> Signed-off-by: David Sterba <[email protected]>
2021-12-15Merge tag 'wireless-drivers-2021-12-15' of ↵David S. Miller8-19/+24
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.16 Second set of fixes for v5.16, hopefully also the last one. I changed my email in MAINTAINERS, one crash fix in iwlwifi and some build problems fixed. iwlwifi * fix crash caused by a warning * fix LED linking problem brcmsmac * rework LED dependencies for being consistent with other drivers mt76 * mt7921: fix build regression ==================== Signed-off-by: David S. Miller <[email protected]>
2021-12-15x86/boot: Move EFI range reservation after cmdline parsingMike Rapoport1-3/+3
The memory reservation in arch/x86/platform/efi/efi.c depends on at least two command line parameters. Put it back later in the boot process and move efi_memblock_x86_reserve_range() out of early_memory_reserve(). An attempt to fix this was done in 8d48bf8206f7 ("x86/boot: Pull up cmdline preparation and early param parsing") but that caused other troubles so it got reverted. The bug this is addressing is: Dan reports that Anjaneya Chagam can no longer use the efi=nosoftreserve kernel command line parameter to suppress "soft reservation" behavior. This is due to the fact that the following call-chain happens at boot: early_reserve_memory |-> efi_memblock_x86_reserve_range |-> efi_fake_memmap_early which does if (!efi_soft_reserve_enabled()) return; and that would have set EFI_MEM_NO_SOFT_RESERVE after having parsed "nosoftreserve". However, parse_early_param() gets called *after* it, leading to the boot cmdline not being taken into account. See also https://lore.kernel.org/r/[email protected] [ bp: Turn into a proper patch. ] Signed-off-by: Mike Rapoport <[email protected]> Signed-off-by: Borislav Petkov <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-15tomoyo: use hwight16() in tomoyo_domain_quota_is_ok()Tetsuo Handa1-10/+7
hwight16() is much faster. While we are at it, no need to include "perm =" part into data_race() macro, for perm is a local variable that cannot be accessed by other threads. Signed-off-by: Tetsuo Handa <[email protected]>
2021-12-15tomoyo: Check exceeded quota early in tomoyo_domain_quota_is_ok().Dmitry Vyukov1-7/+7
If tomoyo is used in a testing/fuzzing environment in learning mode, for lots of domains the quota will be exceeded and stay exceeded for prolonged periods of time. In such cases it's pointless (and slow) to walk the whole acl list again and again just to rediscover that the quota is exceeded. We already have the TOMOYO_DIF_QUOTA_WARNED flag that notes the overflow condition. Check it early to avoid the slowdown. [penguin-kernel] This patch causes a user visible change that the learning mode will not be automatically resumed after the quota is increased. To resume the learning mode, administrator will need to explicitly clear TOMOYO_DIF_QUOTA_WARNED flag after increasing the quota. But I think that this change is generally preferable, for administrator likely wants to optimize the acl list for that domain before increasing the quota, or that domain likely hits the quota again. Therefore, don't try to care to clear TOMOYO_DIF_QUOTA_WARNED flag automatically when the quota for that domain changed. Signed-off-by: Dmitry Vyukov <[email protected]> Signed-off-by: Tetsuo Handa <[email protected]>
2021-12-15Merge branch '100GbE' of ↵David S. Miller2-8/+11
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-12-14 This series contains updates to ice driver only. Karol corrects division that was causing incorrect calculations and adds a check to ensure stale timestamps are not being used. ==================== Signed-off-by: David S. Miller <[email protected]>
2021-12-15Revert "x86/boot: Pull up cmdline preparation and early param parsing"Borislav Petkov1-39/+27
This reverts commit 8d48bf8206f77aa8687f0e241e901e5197e52423. It turned out to be a bad idea as it broke supplying mem= cmdline parameters due to parse_memopt() requiring preparatory work like setting up the e820 table in e820__memory_setup() in order to be able to exclude the range specified by mem=. Pulling that up would've broken Xen PV again, see threads at https://lkml.kernel.org/r/[email protected] due to xen_memory_setup() needing the first reservations in early_reserve_memory() - kernel and initrd - to have happened already. This could be fixed again by having Xen do those reservations itself... Long story short, revert this and do a simpler fix in a later patch. Signed-off-by: Borislav Petkov <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-15Revert "x86/boot: Mark prepare_command_line() __init"Borislav Petkov1-1/+1
This reverts commit c0f2077baa4113f38f008b8e912b9fb3ff8d43df. Signed-off-by: Borislav Petkov <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-12-15ALSA: hda/realtek: fix mute/micmute LEDs for a HP ProBookJeremy Szu1-0/+1
There is a HP ProBook which using ALC236 codec and need the ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make mute LED and micmute LED work. Signed-off-by: Jeremy Szu <[email protected]> Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-12-14bpf, selftests: Update test case for atomic cmpxchg on r0 with pointerDaniel Borkmann1-2/+65
Fix up unprivileged test case results for 'Dest pointer in r0' verifier tests given they now need to reject R0 containing a pointer value, and add a couple of new related ones with 32bit cmpxchg as well. root@foo:~/bpf/tools/testing/selftests/bpf# ./test_verifier #0/u invalid and of negative number OK #0/p invalid and of negative number OK [...] #1268/p XDP pkt read, pkt_meta' <= pkt_data, bad access 1 OK #1269/p XDP pkt read, pkt_meta' <= pkt_data, bad access 2 OK #1270/p XDP pkt read, pkt_data <= pkt_meta', good access OK #1271/p XDP pkt read, pkt_data <= pkt_meta', bad access 1 OK #1272/p XDP pkt read, pkt_data <= pkt_meta', bad access 2 OK Summary: 1900 PASSED, 0 SKIPPED, 0 FAILED Acked-by: Brendan Jackman <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]>
2021-12-14bpf: Fix kernel address leakage in atomic cmpxchg's r0 aux regDaniel Borkmann1-1/+8
The implementation of BPF_CMPXCHG on a high level has the following parameters: .-[old-val] .-[new-val] BPF_R0 = cmpxchg{32,64}(DST_REG + insn->off, BPF_R0, SRC_REG) `-[mem-loc] `-[old-val] Given a BPF insn can only have two registers (dst, src), the R0 is fixed and used as an auxilliary register for input (old value) as well as output (returning old value from memory location). While the verifier performs a number of safety checks, it misses to reject unprivileged programs where R0 contains a pointer as old value. Through brute-forcing it takes about ~16sec on my machine to leak a kernel pointer with BPF_CMPXCHG. The PoC is basically probing for kernel addresses by storing the guessed address into the map slot as a scalar, and using the map value pointer as R0 while SRC_REG has a canary value to detect a matching address. Fix it by checking R0 for pointers, and reject if that's the case for unprivileged programs. Fixes: 5ffa25502b5a ("bpf: Add instructions for atomic_[cmp]xchg") Reported-by: Ryota Shiga (Flatt Security) Acked-by: Brendan Jackman <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]>
2021-12-14bpf, selftests: Add test case for atomic fetch on spilled pointerDaniel Borkmann2-0/+117
Test whether unprivileged would be able to leak the spilled pointer either by exporting the returned value from the atomic{32,64} operation or by reading and exporting the value from the stack after the atomic operation took place. Note that for unprivileged, the below atomic cmpxchg test case named "Dest pointer in r0 - succeed" is failing. The reason is that in the dst memory location (r10 -8) there is the spilled register r10: 0: R1=ctx(id=0,off=0,imm=0) R10=fp0 0: (bf) r0 = r10 1: R0_w=fp0 R1=ctx(id=0,off=0,imm=0) R10=fp0 1: (7b) *(u64 *)(r10 -8) = r0 2: R0_w=fp0 R1=ctx(id=0,off=0,imm=0) R10=fp0 fp-8_w=fp 2: (b7) r1 = 0 3: R0_w=fp0 R1_w=invP0 R10=fp0 fp-8_w=fp 3: (db) r0 = atomic64_cmpxchg((u64 *)(r10 -8), r0, r1) 4: R0_w=fp0 R1_w=invP0 R10=fp0 fp-8_w=mmmmmmmm 4: (79) r1 = *(u64 *)(r0 -8) 5: R0_w=fp0 R1_w=invP(id=0) R10=fp0 fp-8_w=mmmmmmmm 5: (b7) r0 = 0 6: R0_w=invP0 R1_w=invP(id=0) R10=fp0 fp-8_w=mmmmmmmm 6: (95) exit However, allowing this case for unprivileged is a bit useless given an update with a new pointer will fail anyway: 0: R1=ctx(id=0,off=0,imm=0) R10=fp0 0: (bf) r0 = r10 1: R0_w=fp0 R1=ctx(id=0,off=0,imm=0) R10=fp0 1: (7b) *(u64 *)(r10 -8) = r0 2: R0_w=fp0 R1=ctx(id=0,off=0,imm=0) R10=fp0 fp-8_w=fp 2: (db) r0 = atomic64_cmpxchg((u64 *)(r10 -8), r0, r10) R10 leaks addr into mem Acked-by: Brendan Jackman <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]>
2021-12-14bpf: Fix kernel address leakage in atomic fetchDaniel Borkmann1-3/+9
The change in commit 37086bfdc737 ("bpf: Propagate stack bounds to registers in atomics w/ BPF_FETCH") around check_mem_access() handling is buggy since this would allow for unprivileged users to leak kernel pointers. For example, an atomic fetch/and with -1 on a stack destination which holds a spilled pointer will migrate the spilled register type into a scalar, which can then be exported out of the program (since scalar != pointer) by dumping it into a map value. The original implementation of XADD was preventing this situation by using a double call to check_mem_access() one with BPF_READ and a subsequent one with BPF_WRITE, in both cases passing -1 as a placeholder value instead of register as per XADD semantics since it didn't contain a value fetch. The BPF_READ also included a check in check_stack_read_fixed_off() which rejects the program if the stack slot is of __is_pointer_value() if dst_regno < 0. The latter is to distinguish whether we're dealing with a regular stack spill/ fill or some arithmetical operation which is disallowed on non-scalars, see also 6e7e63cbb023 ("bpf: Forbid XADD on spilled pointers for unprivileged users") for more context on check_mem_access() and its handling of placeholder value -1. One minimally intrusive option to fix the leak is for the BPF_FETCH case to initially check the BPF_READ case via check_mem_access() with -1 as register, followed by the actual load case with non-negative load_reg to propagate stack bounds to registers. Fixes: 37086bfdc737 ("bpf: Propagate stack bounds to registers in atomics w/ BPF_FETCH") Reported-by: <[email protected]> Acked-by: Brendan Jackman <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]>
2021-12-14bcache: fix NULL pointer reference in cached_dev_detach_finishLin Feng1-1/+2
Commit 0259d4498ba4 ("bcache: move calc_cached_dev_sectors to proper place on backing device detach") tries to fix calc_cached_dev_sectors when bcache device detaches, but now we have: cached_dev_detach_finish ... bcache_device_detach(&dc->disk); ... closure_put(&d->c->caching); d->c = NULL; [*explicitly set dc->disk.c to NULL*] list_move(&dc->list, &uncached_devices); calc_cached_dev_sectors(dc->disk.c); [*passing a NULL pointer*] ... Upper codeflows shows how bug happens, this patch fix the problem by caching dc->disk.c beforehand, and cache_set won't be freed under us because c->caching closure at least holds a reference count and closure callback __cache_set_unregister only being called by bch_cache_set_stop which using closure_queue(&c->caching), that means c->caching closure callback for destroying cache_set won't be trigger by previous closure_put(&d->c->caching). So at this stage(while cached_dev_detach_finish is calling) it's safe to access cache_set dc->disk.c. Fixes: 0259d4498ba4 ("bcache: move calc_cached_dev_sectors to proper place on backing device detach") Signed-off-by: Lin Feng <[email protected]> Signed-off-by: Coly Li <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jens Axboe <[email protected]>
2021-12-14block: reduce kblockd_mod_delayed_work_on() CPU consumptionJens Axboe1-0/+2
Dexuan reports that he's seeing spikes of very heavy CPU utilization when running 24 disks and using the 'none' scheduler. This happens off the sched restart path, because SCSI requires the queue to be restarted async, and hence we're hammering on mod_delayed_work_on() to ensure that the work item gets run appropriately. Avoid hammering on the timer and just use queue_work_on() if no delay has been specified. Reported-and-tested-by: Dexuan Cui <[email protected]> Link: https://lore.kernel.org/linux-block/BYAPR21MB1270C598ED214C0490F47400BF719@BYAPR21MB1270.namprd21.prod.outlook.com/ Reviewed-by: Ming Lei <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2021-12-14Merge branch 'mptcp-fixes-for-ulp-a-deadlock-and-netlink-docs'Jakub Kicinski3-11/+14
Mat Martineau says: ==================== mptcp: Fixes for ULP, a deadlock, and netlink docs Two of the MPTCP fixes in this set are related to the TCP_ULP socket option with MPTCP sockets operating in "fallback" mode (the connection has reverted to regular TCP). The other issues are an observed deadlock and missing parameter documentation in the MPTCP netlink API. Patch 1 marks TCP_ULP as unsupported earlier in MPTCP setsockopt code, so the fallback code path in the MPTCP layer does not pass the TCP_ULP option down to the subflow TCP socket. Patch 2 makes sure a TCP fallback socket returned to userspace by accept()ing on a MPTCP listening socket does not allow use of the "mptcp" TCP_ULP type. That ULP is intended only for use by in-kernel MPTCP subflows. Patch 3 fixes the possible deadlock when sending data and there are socket option changes to sync to the subflows. Patch 4 makes sure all MPTCP netlink event parameters are documented in the MPTCP uapi header. ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-12-14mptcp: add missing documented NL paramsMatthieu Baerts1-8/+10
'loc_id' and 'rem_id' are set in all events linked to subflows but those were missing in the events description in the comments. Fixes: b911c97c7dc7 ("mptcp: add netlink event support") Signed-off-by: Matthieu Baerts <[email protected]> Signed-off-by: Mat Martineau <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-12-14mptcp: fix deadlock in __mptcp_push_pending()Maxim Galaganov1-1/+1
__mptcp_push_pending() may call mptcp_flush_join_list() with subflow socket lock held. If such call hits mptcp_sockopt_sync_all() then subsequently __mptcp_sockopt_sync() could try to lock the subflow socket for itself, causing a deadlock. sysrq: Show Blocked State task:ss-server state:D stack: 0 pid: 938 ppid: 1 flags:0x00000000 Call Trace: <TASK> __schedule+0x2d6/0x10c0 ? __mod_memcg_state+0x4d/0x70 ? csum_partial+0xd/0x20 ? _raw_spin_lock_irqsave+0x26/0x50 schedule+0x4e/0xc0 __lock_sock+0x69/0x90 ? do_wait_intr_irq+0xa0/0xa0 __lock_sock_fast+0x35/0x50 mptcp_sockopt_sync_all+0x38/0xc0 __mptcp_push_pending+0x105/0x200 mptcp_sendmsg+0x466/0x490 sock_sendmsg+0x57/0x60 __sys_sendto+0xf0/0x160 ? do_wait_intr_irq+0xa0/0xa0 ? fpregs_restore_userregs+0x12/0xd0 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f9ba546c2d0 RSP: 002b:00007ffdc3b762d8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007f9ba56c8060 RCX: 00007f9ba546c2d0 RDX: 000000000000077a RSI: 0000000000e5e180 RDI: 0000000000000234 RBP: 0000000000cc57f0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9ba56c8060 R13: 0000000000b6ba60 R14: 0000000000cc7840 R15: 41d8685b1d7901b8 </TASK> Fix the issue by using __mptcp_flush_join_list() instead of plain mptcp_flush_join_list() inside __mptcp_push_pending(), as suggested by Florian. The sockopt sync will be deferred to the workqueue. Fixes: 1b3e7ede1365 ("mptcp: setsockopt: handle SO_KEEPALIVE and SO_PRIORITY") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/244 Suggested-by: Florian Westphal <[email protected]> Reviewed-by: Florian Westphal <[email protected]> Signed-off-by: Maxim Galaganov <[email protected]> Signed-off-by: Mat Martineau <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-12-14mptcp: clear 'kern' flag from fallback socketsFlorian Westphal1-1/+3
The mptcp ULP extension relies on sk->sk_sock_kern being set correctly: It prevents setsockopt(fd, IPPROTO_TCP, TCP_ULP, "mptcp", 6); from working for plain tcp sockets (any userspace-exposed socket). But in case of fallback, accept() can return a plain tcp sk. In such case, sk is still tagged as 'kernel' and setsockopt will work. This will crash the kernel, The subflow extension has a NULL ctx->conn mptcp socket: BUG: KASAN: null-ptr-deref in subflow_data_ready+0x181/0x2b0 Call Trace: tcp_data_ready+0xf8/0x370 [..] Fixes: cf7da0d66cc1 ("mptcp: Create SUBFLOW socket for incoming connections") Signed-off-by: Florian Westphal <[email protected]> Signed-off-by: Mat Martineau <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-12-14mptcp: remove tcp ulp setsockopt supportFlorian Westphal1-1/+0
TCP_ULP setsockopt cannot be used for mptcp because its already used internally to plumb subflow (tcp) sockets to the mptcp layer. syzbot managed to trigger a crash for mptcp connections that are in fallback mode: KASAN: null-ptr-deref in range [0x0000000000000020-0x0000000000000027] CPU: 1 PID: 1083 Comm: syz-executor.3 Not tainted 5.16.0-rc2-syzkaller #0 RIP: 0010:tls_build_proto net/tls/tls_main.c:776 [inline] [..] __tcp_set_ulp net/ipv4/tcp_ulp.c:139 [inline] tcp_set_ulp+0x428/0x4c0 net/ipv4/tcp_ulp.c:160 do_tcp_setsockopt+0x455/0x37c0 net/ipv4/tcp.c:3391 mptcp_setsockopt+0x1b47/0x2400 net/mptcp/sockopt.c:638 Remove support for TCP_ULP setsockopt. Fixes: d9e4c1291810 ("mptcp: only admit explicitly supported sockopt") Reported-by: [email protected] Signed-off-by: Florian Westphal <[email protected]> Signed-off-by: Mat Martineau <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-12-14RDMA/hns: Replace kfree() with kvfree()Jiacheng Shi1-1/+1
Variables allocated by kvmalloc_array() should not be freed by kfree. Because they may be allocated by vmalloc. So we replace kfree() with kvfree() here. Fixes: 6fd610c5733d ("RDMA/hns: Support 0 hop addressing for SRQ buffer") Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jiacheng Shi <[email protected]> Acked-by: Wenpeng Liang <[email protected]> Signed-off-by: Jason Gunthorpe <[email protected]>
2021-12-14IB/qib: Fix memory leak in qib_user_sdma_queue_pkts()José Expósito1-1/+1
The wrong goto label was used for the error case and missed cleanup of the pkt allocation. Fixes: d39bf40e55e6 ("IB/qib: Protect from buffer overflow in struct qib_user_sdma_pkt fields") Link: https://lore.kernel.org/r/[email protected] Addresses-Coverity-ID: 1493352 ("Resource leak") Signed-off-by: José Expósito <[email protected]> Acked-by: Mike Marciniszyn <[email protected]> Signed-off-by: Jason Gunthorpe <[email protected]>
2021-12-14RDMA/hns: Fix RNR retransmission issue for HIP08Yangyang Li2-7/+65
Due to the discrete nature of the HIP08 timer unit, a requester might finish the timeout period sooner, in elapsed real time, than its responder does, even when both sides share the identical RNR timeout length included in the RNR Nak packet and the responder indeed starts the timing prior to the requester. Furthermore, if a 'providential' resend packet arrived before the responder's timeout period expired, the responder is certainly entitled to drop the packet silently in the light of IB protocol. To address this problem, our team made good use of certain hardware facts: 1) The timing resolution regards the transmission arrangements is 1 microsecond, e.g. if cq_period field is set to 3, it would be interpreted as 3 microsecond by hardware 2) A QPC field shall inform the hardware how many timing unit (ticks) constitutes a full microsecond, which, by default, is 1000 3) It takes 14ns for the processor to handle a packet in the buffer, so the RNR timeout length of 10ns would ensure our processing mechanism is disabled during the entire timeout period and the packet won't be dropped silently To achieve (3), we permanently set the QPC field mentioned in (2) to zero which nominally indicates every time tick is equivalent to a microsecond in wall-clock time; now, a RNR timeout period at face value of 10 would only last 10 ticks, which is 10ns in wall-clock time. It's worth noting that we adapt the driver by magnifying certain configuration parameters(cq_period, eq_period and ack_timeout)by 1000 given the user assumes the configuring timing unit to be microseconds. Also, this particular improvisation is only deployed on HIP08 since other hardware has already solved this issue. Fixes: cfc85f3e4b7f ("RDMA/hns: Add profile support for hip08 driver") Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Yangyang Li <[email protected]> Signed-off-by: Wenpeng Liang <[email protected]> Signed-off-by: Jason Gunthorpe <[email protected]>
2021-12-14drm/amd/pm: fix a potential gpu_metrics_table memory leakLang Yu1-0/+3
Memory is allocated for gpu_metrics_table in renoir_init_smc_tables(), but not freed in int smu_v12_0_fini_smc_tables(). Free it! Fixes: 95868b85764a ("drm/amd/powerplay: add Renoir support for gpu metrics export") Signed-off-by: Lang Yu <[email protected]> Reviewed-by: Lijo Lazar <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2021-12-14drm/amdgpu: correct the wrong cached state for GMC on PICASSOEvan Quan3-5/+18
Pair the operations did in GMC ->hw_init and ->hw_fini. That can help to maintain correct cached state for GMC and avoid unintention gate operation dropping due to wrong cached state. BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1828 Signed-off-by: Evan Quan <[email protected]> Acked-by: Guchun Chen <[email protected]> Reviewed-by: Mario Limonciello <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2021-12-14drm/amd/display: Reset DMCUB before HW initNicholas Kazlauskas1-0/+5
[Why] If the firmware wasn't reset by PSP or HW and is currently running then the firmware will hang or perform underfined behavior when we modify its firmware state underneath it. [How] Reset DMCUB before setting up cache windows and performing HW init. Reviewed-by: Aurabindo Jayamohanan Pillai <[email protected]> Acked-by: Pavle Kotarac <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Nicholas Kazlauskas <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2021-12-14drm/amd/display: Set exit_optimized_pwr_state for DCN31Nicholas Kazlauskas1-0/+1
[Why] SMU now respects the PHY refclk disable request from driver. This causes a hang during hotplug when PHY refclk was disabled because it's not being re-enabled and the transmitter control starts on dc_link_detect. [How] We normally would re-enable the clk with exit_optimized_pwr_state but this is only set on DCN21 and DCN301. Set it for dcn31 as well. This fixes DMCUB timeouts in the PHY. Fixes: 64b1d0e8d500 ("drm/amd/display: Add DCN3.1 HWSEQ") Reviewed-by: Eric Yang <[email protected]> Acked-by: Pavle Kotarac <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Nicholas Kazlauskas <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
2021-12-14drm/amd/pm: fix reading SMU FW version from amdgpu_firmware_info on YCMario Limonciello1-0/+3
This value does not get cached into adev->pm.fw_version during startup for smu13 like it does for other SMU like smu12. Signed-off-by: Mario Limonciello <[email protected]> Reviewed-by: Alex Deucher <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected]
2021-12-14drm/amdgpu: don't override default ECO_BITs settingHawking Zhang8-9/+0
Leave this bit as hardware default setting Signed-off-by: Hawking Zhang <[email protected]> Reviewed-by: Alex Deucher <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected]
2021-12-14drm/amdgpu: correct register access for RLC_JUMP_TABLE_RESTORELe Ma1-2/+2
should count on GC IP base address Signed-off-by: Le Ma <[email protected]> Signed-off-by: Hawking Zhang <[email protected]> Reviewed-by: Hawking Zhang <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Cc: [email protected]
2021-12-14signal: Skip the altstack update when not neededChang S. Bae1-0/+9
== Background == Support for large, "dynamic" fpstates was recently merged. This included code to ensure that sigaltstacks are sufficiently sized for these large states. A new lock was added to remove races between enabling large features and setting up sigaltstacks. == Problem == The new lock (sigaltstack_lock()) is acquired in the sigreturn path before restoring the old sigaltstack. Unfortunately, contention on the new lock causes a measurable signal handling performance regression [1]. However, the common case is that no *changes* are made to the sigaltstack state at sigreturn. == Solution == do_sigaltstack() acquires sigaltstack_lock() and is used for both sys_sigaltstack() and restoring the sigaltstack in sys_sigreturn(). Check for changes to the sigaltstack before taking the lock. If no changes were made, return before acquiring the lock. This removes lock contention from the common-case sigreturn path. [1] https://lore.kernel.org/lkml/20211207012128.GA16074@xsang-OptiPlex-9020/ Fixes: 3aac3ebea08f ("x86/signal: Implement sigaltstack size validation") Reported-by: kernel test robot <[email protected]> Signed-off-by: Chang S. Bae <[email protected]> Signed-off-by: Dave Hansen <[email protected]> Reviewed-by: Thomas Gleixner <[email protected]> Link: https://lkml.kernel.org/r/[email protected]
2021-12-14ice: Don't put stale timestamps in the skbKarol Kolacinski2-7/+10
The driver has to check if it does not accidentally put the timestamp in the SKB before previous timestamp gets overwritten. Timestamp values in the PHY are read only and do not get cleared except at hardware reset or when a new timestamp value is captured. The cached_tstamp field is used to detect the case where a new timestamp has not yet been captured, ensuring that we avoid sending stale timestamp data to the stack. Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices") Signed-off-by: Karol Kolacinski <[email protected]> Tested-by: Gurucharan G <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
2021-12-14ice: Use div64_u64 instead of div_u64 in adjfineKarol Kolacinski1-1/+1
Change the division in ice_ptp_adjfine from div_u64 to div64_u64. div_u64 is used when the divisor is 32 bit but in this case incval is 64 bit and it caused incorrect calculations and incval adjustments. Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices") Signed-off-by: Karol Kolacinski <[email protected]> Tested-by: Gurucharan G <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.