| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On the switch on the MT7988 SoC, as shown in Block Diagram 8.1.1.3 on page
125 of "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open
Version) v0.1", there are only 4 PHYs. That's port 0 to 3. Set the case for
ports which connect to switch PHYs to '0 ... 3'.
Port 4 and 5 are not used at all in this design.
Link: https://wiki.banana-pi.org/Banana_Pi_BPI-R4#Documents [1]
Acked-by: Daniel Golle <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-6-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The pad_setup function pointer was introduced with 88bdef8be9f6 ("net: dsa:
mt7530: Extend device data ready for adding a new hardware"). It was being
used to set up the core clock and port 6 of the MT7530 switch, and pll of
the MT7531 switch.
All of these were moved to more appropriate locations, and it was never
used for the switch on the MT7988 SoC. Therefore, this function pointer
hasn't got a use anymore. Remove it.
Acked-by: Daniel Golle <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-5-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
mt7530_pad_clk_setup() is called if port 6 is enabled. It used to do more
things than setting up port 6. That part was moved to more appropriate
locations, mt7530_setup() and mt7530_pll_setup().
Now that all it does is set up port 6, rename it to mt7530_setup_port6(),
and move it to a more appropriate location, under mt7530_mac_config().
Change mt7530_setup_port6() to void as there're no error cases.
Leave an empty mt7530_pad_clk_setup() to satisfy the pad_setup function
pointer.
This is the code path for setting up the ports before:
dsa_switch_ops :: phylink_mac_config() -> mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt753x_info :: mac_port_config() -> mt7530_mac_config()
-> mt7530_setup_port5()
-> mt753x_pad_setup()
-> mt753x_info :: pad_setup() -> mt7530_pad_clk_setup()
This is after:
dsa_switch_ops :: phylink_mac_config() -> mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt753x_info :: mac_port_config() -> mt7530_mac_config()
-> mt7530_setup_port5()
-> mt7530_setup_port6()
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-4-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This code is from before this driver was converted to phylink API. Phylink
deals with the unsupported interface cases before mt7530_pad_clk_setup() is
run. Therefore, the default case would never run. However, it must be
defined nonetheless to handle all the remaining enumeration values, the
phy-modes.
Switch to if statement for RGMII and return which simplifies the code and
saves an indent.
Set P6_INTF_MODE, which is the three least significant bits of the
MT7530_P6ECR register, to 0 for RGMII even though it will already be 0
after reset. This is to keep supporting dynamic reconfiguration of the port
in the case the interface changes from TRGMII to RGMII.
Disable the TRGMII clocks for all cases. They will be enabled if TRGMII is
being used.
Read XTAL after checking for RGMII as it's only needed for the TRGMII
interface mode.
Reviewed-by: Daniel Golle <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-3-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The crystal frequency concerns the switch core. The frequency should be
checked when the switch is being set up so the driver can reject the
unsupported hardware earlier and without requiring port 6 to be used.
Move it to mt7530_setup(). Drop the unnecessary function printing.
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-2-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
There're two code paths for setting up port 5:
mt7530_setup()
-> mt7530_setup_port5()
mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt7530_mac_config()
-> mt7530_setup_port5()
On the first code path, priv->p5_intf_sel is either set to
P5_INTF_SEL_PHY_P0 or P5_INTF_SEL_PHY_P4 when mt7530_setup_port5() is run.
On the second code path, priv->p5_intf_sel is set to P5_INTF_SEL_GMAC5 when
mt7530_setup_port5() is run.
Empty the default case which will never run but is needed nonetheless to
handle all the remaining enumeration values.
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Arınç ÜNAL <[email protected]>
Link: https://lore.kernel.org/r/20240206-for-netnext-mt7530-improvements-2-v5-1-d7d92a185cb1@arinc9.com
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
After 1c75c424bd43 ("leds: class: If no default trigger is given, make
hw_control trigger the default trigger") this line isn't needed any
longer.
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2024-02-01
1) IPSec global stats for xfrm and mlx5
2) XSK memory improvements for non-linear SKBs
3) Software steering debug dump to use seq_file ops
4) Various code clean-ups
* tag 'mlx5-updates-2024-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: XDP, Exclude headroom and tailroom from memory calculations
net/mlx5e: XSK, Exclude tailroom from non-linear SKBs memory calculations
net/mlx5: DR, Change SWS usage to debug fs seq_file interface
net/mlx5: Change missing SyncE capability print to debug
net/mlx5: Remove initial segmentation duplicate definitions
net/mlx5: Return specific error code for timeout on wait_fw_init
net/mlx5: SF, Stop waiting for FW as teardown was called
net/mlx5: remove fw reporter dump option for non PF
net/mlx5: remove fw_fatal reporter dump option for non PF
net/mlx5: Rename mlx5_sf_dev_remove
Documentation: Fix counter name of mlx5 vnic reporter
net/mlx5e: Delete obsolete IPsec code
net/mlx5e: Connect mlx5 IPsec statistics with XFRM core
xfrm: get global statistics from the offloaded device
xfrm: generalize xdo_dev_state_update_curlft to allow statistics update
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Hangbin Liu says:
====================
selftests: bonding: use slowwait when waiting
There are a lot waitings in bonding tests use sleep. Let's replace them with
slowwait(added in the first patch). This could save much test time. e.g.
bond-break-lacpdu-tx.sh
before: 0m16.346s
after: 0m2.824s
bond_options.sh
before: 9m25.299s
after: 6m14.439s
bond-lladdr-target.sh
before: 0m7.090s
after: 0m6.148s
In total, we could save about 180 seconds.
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Use slowwait instead of hard code sleep for bonding tests.
In function setup_prepare(), the client_create() will be called after
server_create(). So I think there is no need to sleep in server_create()
and remove it.
For lab_lib.sh, remove bonding module may affect other running bonding tests.
And some test env may buildin bond which can't be removed. The bonding
link should be removed by lag_reset_network() or netns delete.
Signed-off-by: Hangbin Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The purpose of grat_arp is testing commit 9949e2efb54e ("bonding: fix
send_peer_notif overflow"). As the send_peer_notif was defined to u8,
to overflow it, we need to
send_peer_notif = num_peer_notif * peer_notif_delay = num_grat_arp * peer_notify_delay / miimon > 255
(kernel) (kernel parameter) (user parameter)
e.g. 30 (num_grat_arp) * 1000 (peer_notify_delay) / 100 (miimon) > 255.
Which need 30s to complete sending garp messages. To save the testing time,
the only way is reduce the miimon number. Something like
30 (num_grat_arp) * 100 (peer_notify_delay) / 10 (miimon) > 255.
To save more time, the 50 num_grat_arp testing could be removed.
The arp_validate_test also need to check the mii_status, which sleep
too long. Use slowwait to save some time.
For other connection checkings, make sure active slave changed first.
Reviewed-by: Przemek Kitszel <[email protected]>
Signed-off-by: Hangbin Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Use tc filter to check if LACP was sent, which is accurate and save
more time.
No need to remove bonding module as some test env may buildin bonding.
And the bond link has been deleted.
Reviewed-by: Przemek Kitszel <[email protected]>
Signed-off-by: Hangbin Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add slowwait functions to wait for some operations that may need a long time
to finish. The busywait executes the cmd too fast, which is kind of wasting
cpu in this scenario. At the same time, if shell debugging is enabled with
`set -x`. the busywait will output too much logs.
Reviewed-by: Przemek Kitszel <[email protected]>
Signed-off-by: Hangbin Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
According to latest release of SMCv2.1[1], the term 'virtual ISM' has
been changed to 'Emulated-ISM' to avoid the ambiguity of the word
'virtual' in different contexts. So the names or comments in the code
need be modified accordingly.
[1] https://www.ibm.com/support/pages/node/7112343
Signed-off-by: Wen Gu <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Wenjia Zhang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
'net-phy-realtek-complete-5gbps-support-and-replace-private-constants'
Heiner Kallweit says:
====================
net: phy: realtek: complete 5Gbps support and replace private constants
Realtek maps standard C45 registers to vendor-specific registers which
can be accessed via C22 w/o MMD. For an unknown reason C22 MMD access
to C45 registers isn't supported for integrated PHY's.
However the vendor-specific registers preserve the format of the C45
registers, so we can use standard constants. First two patches are
cherry-picked from a series posted by Marek some time ago.
RTL8126 supports 5Gbps, therefore add the missing 5Gbps support to
rtl822x_config_aneg().
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
RTL8126 as an evolution of RTL8125 supports 5Gbps. rtl822x_config_aneg()
is used by the PHY driver for the integrated PHY, therefore add 5Gbps
support to it.
Signed-off-by: Heiner Kallweit <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Drop the ad-hoc MDIO constants used in the driver and use generic
constants instead.
Signed-off-by: Marek Behún <[email protected]>
Signed-off-by: Heiner Kallweit <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add constants indicating 2.5g and 5g ability in the MMD PMA speed
register.
Signed-off-by: Marek Behún <[email protected]>
Signed-off-by: Heiner Kallweit <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
xt_check_{match,target} expects u16, but NFTA_RULE_COMPAT_PROTO is u32.
NLA_POLICY_MAX(NLA_BE32, 65535) cannot be used because .max in
nla_policy is s16, see 3e48be05f3c7 ("netlink: add attribute range
validation to policy").
Fixes: 0ca743a55991 ("netfilter: nf_tables: add compatibility layer for x_tables")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Flag (1 << 0) is ignored is set, never used, reject it it with EINVAL
instead.
Fixes: 0ca743a55991 ("netfilter: nf_tables: add compatibility layer for x_tables")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
xt_find_revision() expects u8, restrict it to this datatype.
Fixes: 0ca743a55991 ("netfilter: nf_tables: add compatibility layer for x_tables")
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Similar to what is done in dpll_device_unregister(), add assertion to
__dpll_pin_unregister() to make sure driver does not try to unregister
non-registered pin.
Signed-off-by: Jiri Pirko <[email protected]>
Reviewed-by: Vadim Fedorenko <[email protected]>
Reviewed-by: Arkadiusz Kubalewski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.8-rc4
This time we have unusually large wireless pull request. Several
functionality fixes to both stack and iwlwifi. Lots of fixes to
warnings, especially to MODULE_DESCRIPTION().
* tag 'wireless-2024-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (31 commits)
wifi: mt76: mt7996: fix fortify warning
wifi: brcmfmac: Adjust n_channels usage for __counted_by
wifi: iwlwifi: do not announce EPCS support
wifi: iwlwifi: exit eSR only after the FW does
wifi: iwlwifi: mvm: fix a battery life regression
wifi: mac80211: accept broadcast probe responses on 6 GHz
wifi: mac80211: adding missing drv_mgd_complete_tx() call
wifi: mac80211: fix waiting for beacons logic
wifi: mac80211: fix unsolicited broadcast probe config
wifi: mac80211: initialize SMPS mode correctly
wifi: mac80211: fix driver debugfs for vif type change
wifi: mac80211: set station RX-NSS on reconfig
wifi: mac80211: fix RCU use in TDLS fast-xmit
wifi: mac80211: improve CSA/ECSA connection refusal
wifi: cfg80211: detect stuck ECSA element in probe resp
wifi: iwlwifi: remove extra kernel-doc
wifi: fill in MODULE_DESCRIPTION()s for mt76 drivers
wifi: fill in MODULE_DESCRIPTION()s for wilc1000
wifi: fill in MODULE_DESCRIPTION()s for wl18xx
wifi: fill in MODULE_DESCRIPTION()s for p54spi
...
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix acpi_core_pic[] array overflow, fix earlycon parameter if KASAN
enabled, disable UBSAN instrumentation for vDSO build, and two Kconfig
cleanups"
* tag 'loongarch-fixes-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: vDSO: Disable UBSAN instrumentation
LoongArch: Fix earlycon parameter if KASAN enabled
LoongArch: Change acpi_core_pic[NR_CPUS] to acpi_core_pic[MAX_CORE_PIC]
LoongArch: Select HAVE_ARCH_SECCOMP to use the common SECCOMP menu
LoongArch: Select ARCH_ENABLE_THP_MIGRATION instead of redefining it
|
|
Pull kvm fixes from Paolo Bonzini:
"x86 guest:
- Avoid false positive for check that only matters on AMD processors
x86:
- Give a hint when Win2016 might fail to boot due to XSAVES &&
!XSAVEC configuration
- Do not allow creating an in-kernel PIT unless an IOAPIC already
exists
RISC-V:
- Allow ISA extensions that were enabled for bare metal in 6.8 (Zbc,
scalar and vector crypto, Zfh[min], Zihintntl, Zvfh[min], Zfa)
S390:
- fix CC for successful PQAP instruction
- fix a race when creating a shadow page"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86/coco: Define cc_vendor without CONFIG_ARCH_HAS_CC_PLATFORM
x86/kvm: Fix SEV check in sev_map_percpu_data()
KVM: x86: Give a hint when Win2016 might fail to boot due to XSAVES erratum
KVM: x86: Check irqchip mode before create PIT
KVM: riscv: selftests: Add Zfa extension to get-reg-list test
RISC-V: KVM: Allow Zfa extension for Guest/VM
KVM: riscv: selftests: Add Zvfh[min] extensions to get-reg-list test
RISC-V: KVM: Allow Zvfh[min] extensions for Guest/VM
KVM: riscv: selftests: Add Zihintntl extension to get-reg-list test
RISC-V: KVM: Allow Zihintntl extension for Guest/VM
KVM: riscv: selftests: Add Zfh[min] extensions to get-reg-list test
RISC-V: KVM: Allow Zfh[min] extensions for Guest/VM
KVM: riscv: selftests: Add vector crypto extensions to get-reg-list test
RISC-V: KVM: Allow vector crypto extensions for Guest/VM
KVM: riscv: selftests: Add scaler crypto extensions to get-reg-list test
RISC-V: KVM: Allow scalar crypto extensions for Guest/VM
KVM: riscv: selftests: Add Zbc extension to get-reg-list test
RISC-V: KVM: Allow Zbc extension for Guest/VM
KVM: s390: fix cc for successful PQAP
KVM: s390: vsie: fix race during shadow creation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fix from Chuck Lever:
- Address a deadlock regression in RELEASE_LOCKOWNER
* tag 'nfsd-6.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: don't take fi_lock in nfsd_break_deleg_cb()
|
|
All filtering parameters such as EtherType and VLAN TCI are stored in host
byte order except for the VLAN EtherType. Unify it.
Signed-off-by: Kurt Kanzenbach <[email protected]>
Acked-by: Vinicius Costa Gomes <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Naama Meir <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
All igc filter implementations use netdev_*() printing functions except for
the flex filters. Unify it.
Signed-off-by: Kurt Kanzenbach <[email protected]>
Acked-by: Vinicius Costa Gomes <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Naama Meir <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
Use reverse xmas tree coding style convention in igc_add_flex_filter().
Signed-off-by: Kurt Kanzenbach <[email protected]>
Acked-by: Vinicius Costa Gomes <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Tested-by: Naama Meir <[email protected]>
Signed-off-by: Tony Nguyen <[email protected]>
|
|
The kernel build regressions/improvements email contained a couple of
issues with old compilers (in fact all the reports were on different
architectures, but all gcc 5.5) and the FIELD_PREP() and FIELD_GET()
conversions. They're all because an integer #define that should have
been declared as unsigned, was shifted to the point that it could set
the sign bit.
The fix just involves making sure the defines use the "U" identifier on
the constants to make sure they're unsigned. Should make the checkers
happier.
Confirmed with objdump before/after that there is no change to the
binaries.
Issues were reported as follows:
./drivers/net/ethernet/intel/ice/ice_base.c:238:7: note: in expansion of macro 'FIELD_GET'
(FIELD_GET(GLINT_CTL_ITR_GRAN_25_M, regval) == ICE_ITR_GRAN_US))
^
./include/linux/compiler_types.h:435:38: error: call to '__compiletime_assert_1093' declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_nvm.c:709:16: note: in expansion of macro ‘FIELD_GET’
orom->major = FIELD_GET(ICE_OROM_VER_MASK, combo_ver);
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_796’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_common.c:945:18: note: in expansion of macro ‘FIELD_GET’
u8 max_agg_bw = FIELD_GET(GL_PWR_MODE_CTL_CAR_MAX_BW_M,
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_420’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/i40e/i40e_dcb.c:458:8: note: in expansion of macro ‘FIELD_GET’
oui = FIELD_GET(I40E_LLDP_TLV_OUI_MASK, ouisubtype);
^
Reported-by: Geert Uytterhoeven <[email protected]>
Closes: https://lore.kernel.org/lkml/[email protected]/ #i40e #ice
Fixes: 62589808d73b ("i40e: field get conversion")
Fixes: 5a259f8e0baf ("ice: field get conversion")
Signed-off-by: Jesse Brandeburg <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
A wrapper function is available since the commit 890cc39a879906b63912482dfc41944579df2dc6
("drivers: provide devm_platform_get_and_ioremap_resource()").
Thus reuse existing functionality instead of keeping duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <[email protected]>
Tested-by: Gerhard Engleder <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
init_dummy_netdev() always returns zero and all the callers do not check
the returned value. Set the function to not return value, as it is not
really used today.
Signed-off-by: Amit Cohen <[email protected]>
Reviewed-by: Ido Schimmel <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
At this point, Santosh has moved onto other things and I am happy
to take over the role of rds maintainer. Update the MAINTAINERS
accordingly.
Signed-off-by: Allison Henderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Russell King says:
====================
net: eee network driver cleanups
Since commit d1420bb99515 ("net: phy: improve generic EEE ethtool
functions") changed phylib to set eee->eee_active and eee->eee_enabled,
overriding anything that drivers have set these to prior to calling
phy_ethtool_get_eee().
Therefore, drivers setting these members becomes redundant, since
phylib overwrites the values they set. This series finishes off
Heiner's work in the referenced commit by removing these redundant
writes in various drivers and any associated code or structure members
that become unnecessary.
====================
Link: https://lore.kernel.org/r/Zb9/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
b53_get_mac_eee() sets both eee_enabled and eee_active, and then
returns zero.
dsa_slave_get_eee(), which calls this function, will then continue to
call phylink_ethtool_get_eee(), which will return -EOPNOTSUPP if there
is no PHY present, otherwise calling phy_ethtool_get_eee() which in
turn will call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Thus, when there is no PHY, dsa_slave_get_eee() will fail with
-EOPNOTSUPP, meaning eee_enabled and eee_active will not be returned to
userspace. When there is a PHY, eee_enabled and eee_active will be
overwritten by phylib, making the setting of these members in
b53_get_mac_eee() entirely unnecessary.
Remove this code, thus simplifying b53_get_mac_eee().
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Russell King (Oracle) <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
bcmasp_get_eee() sets edata->eee_active and edata->eee_enabled from
its own copy, and then calls phy_ethtool_get_eee() which in turn will
call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Therefore, setting these members in bcmasp_get_eee() is redundant, and
can be removed. This also makes intf->eee.eee_active unnecessary, so
remove this and use a local variable where appropriate.
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
bcmgenet_get_eee() sets edata->eee_active and edata->eee_enabled from
its own copy, and then calls phy_ethtool_get_eee() which in turn will
call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Therefore, setting these members in bcmgenet_get_eee() is redundant,
and can be removed. This also makes priv->eee.eee_active unnecessary,
so remove this and use a local variable where appropriate.
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
fec_enet_get_eee() sets edata->eee_active and edata->eee_enabled from
its own copy, and then calls phy_ethtool_get_eee() which in turn will
call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Therefore, setting these members in fec_enet_get_eee() is redundant.
Remove this, and remove the setting of fep->eee.eee_active member which
becomes a write-only variable.
Signed-off-by: Russell King (Oracle) <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
sxgbe_get_eee() sets edata->eee_active and edata->eee_enabled from its
own copy, and then calls phy_ethtool_get_eee() which in turn will call
genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Therefore, setting these members in sxgbe_get_eee() is redundant.
Remove this, and remove the priv->eee_active member which then becomes
a write-only variable.
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Russell King (Oracle) <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
stmmac_ethtool_op_get_eee() sets both eee_enabled and eee_active, and
then goes on to call phylink_ethtool_get_eee().
phylink_ethtool_get_eee() will return -EOPNOTSUPP if there is no PHY
present, otherwise calling phy_ethtool_get_eee() which in turn will call
genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Thus, when there is no PHY, stmmac_ethtool_op_get_eee() will fail with
-EOPNOTSUPP, meaning eee_enabled and eee_active will not be returned to
userspace. When there is a PHY, eee_enabled and eee_active will be
overwritten by phylib, making the setting of these members in
stmmac_ethtool_op_get_eee() entirely unnecessary.
Remove this code, thus simplifying stmmac_ethtool_op_get_eee().
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Russell King (Oracle) <[email protected]>
Reviewed-by: Serge Semin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
From: Andrew Lunn <[email protected]>
To: Heiner Kallweit <[email protected]>,
Russell King <[email protected]>,
"David S. Miller" <[email protected]>,
Eric Dumazet <[email protected]>,
Jakub Kicinski <[email protected]>,
Paolo Abeni <[email protected]>,
Florian Fainelli <[email protected]>,
Vladimir Oltean <[email protected]>
Cc: [email protected],
Tim Menninger <[email protected]>,
Andrew Lunn <[email protected]>
====================
net: Unify C22 and C45 error handling during bus enumeration
When enumerating an MDIO bus, an MDIO bus driver can return -ENODEV to
a C22 read transaction to indicate there is no device at that address
on the bus. Enumeration will then continue with the next address on
the bus.
Modify C45 enumeration so that it also accepts -ENODEV and moves to
the next address on the bus, rather than consider -ENODEV as a fatal
error.
Convert the mv88e6xxx driver to return -ENODEV rather than 0xffff on
read for families which do not support C45 bus transactions. This is
more efficient, since enumeration will scan multiple devices at one
address when 0xffff is returned, where as -EONDEV immediately jumps to
the next address on the bus.
====================
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
MDIO bus drivers can return -ENODEV when they know the bus does not
have a device at the given address, e.g. because of hardware
limitation. One such limitation is that the bus does not support C45
at all. This is more efficient than returning 0xffff, since it
immediately stops the probing on the given address, where as further
reads can be made when 0xffff is returned.
Signed-off-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When scanning the MDIO bus for C22 devices, the driver returning
-ENODEV is not considered fatal, it just indicates the MDIO bus master
knows there is no device at that address, maybe because of hardware
limitation.
Make the C45 scan code act on -ENODEV the same way, to make C22 and
C45 more uniform.
It is expected all reads for a given address will return -ENODEV, so
within get_phy_c45_ids() only the first place a read occurs has been
changed.
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Now that the driver core can properly handle constant struct bus_type,
move the nsim_bus variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <[email protected]>
Suggested-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Ricardo B. Marliere <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
cmsg_ipv6 test requests tcpdump to capture 4 packets,
and sends until tcpdump quits. Only the first packet
is "real", however, and the rest are basic UDP packets.
So if tcpdump doesn't start in time it will miss
the real packet and only capture the UDP ones.
This makes the test fail on slow machine (no KVM or with
debug enabled) 100% of the time, while it passes in fast
environments.
Repeat the "real" / expected packet.
Fixes: 9657ad09e1fa ("selftests: net: test IPV6_TCLASS")
Fixes: 05ae83d5a4a2 ("selftests: net: test IPV6_HOPLIMIT")
Signed-off-by: Jakub Kicinski <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The 'bool' is already specified for these options.
The second 'bool' under the help message is redundant.
While I am here, I moved 'default y' above, as it is common to place
the help text last.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Randy Dunlap <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Both drivers/net/Kconfig and drivers/net/ethernet/Kconfig contain the
same config entry:
config SUNGEM_PHY
tristate
Commit f860b0522f65 ("drivers/net: Kconfig and Makefile cleanup") moved
SUNGEM_PHY from drivers/net/Kconfig to drivers/net/ethernet/Kconfig.
Shortly after it was applied, commit 19e2f6fe9601 ("net: Fix sungem_phy
sharing.") added the second one to drivers/net/Kconfig.
I kept the one in drivers/net/Kconfig because this CONFIG option controls
the compilation of drivers/net/sungem_phy.c.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Simplify the code from macro NETLBL_CATMAP_MAPTYPE to u64, and fix
warning "Macros with complex values should be enclosed in parentheses"
on "#define NETLBL_CATMAP_BIT (NETLBL_CATMAP_MAPTYPE)0x01", which is
modified to "#define NETLBL_CATMAP_BIT ((u64)0x01)".
Signed-off-by: George Guo <[email protected]>
Acked-by: Paul Moore <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
As explained by a comment in <linux/u64_stats_sync.h>, write side of struct
u64_stats_sync must ensure mutual exclusion, or one seqcount update could
be lost on 32-bit platforms, thus blocking readers forever. Such lockups
have been observed in real world after stmmac_xmit() on one CPU raced with
stmmac_napi_poll_tx() on another CPU.
To fix the issue without introducing a new lock, split the statics into
three parts:
1. fields updated only under the tx queue lock,
2. fields updated only during NAPI poll,
3. fields updated only from interrupt context,
Updates to fields in the first two groups are already serialized through
other locks. It is sufficient to split the existing struct u64_stats_sync
so that each group has its own.
Note that tx_set_ic_bit is updated from both contexts. Split this counter
so that each context gets its own, and calculate their sum to get the total
value in stmmac_get_ethtool_stats().
For the third group, multiple interrupts may be processed by different CPUs
at the same time, but interrupts on the same CPU will not nest. Move fields
from this group to a newly created per-cpu struct stmmac_pcpu_stats.
Fixes: 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics where necessary")
Link: https://lore.kernel.org/netdev/[email protected]/t/
Cc: [email protected]
Signed-off-by: Petr Tesarik <[email protected]>
Reviewed-by: Jisheng Zhang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- two fixes preventing deletion and manual creation of subvolume qgroup
- unify error code returned for unknown send flags
- fix assertion during subvolume creation when anonymous device could
be allocated by other thread (e.g. due to backref walk)
* tag 'for-6.8-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: do not ASSERT() if the newly created subvolume already got read
btrfs: forbid deleting live subvol qgroup
btrfs: forbid creating subvol qgroups
btrfs: send: return EOPNOTSUPP on unknown flags
|