| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add an overlay to change from the default OSPI NOR to QSPI NOR
for all am6xx-phycore-som boards.
The EEPROM on am6xx-phycore-soms contains information about the
configuration of the SOM. The standard configuration of the SOM
has an ospi nor, but if qspi nor is populated, the EEPROM will
indicate that change and we can use this overlay to cleanly change to
qspi nor.
Signed-off-by: Nathan Morrisson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
MIT license was added to the AM64x SoC DTSIs in commit 6248b20e3203
("arm64: dts: ti: k3-am64: Add MIT license along with GPL-2.0"). Apply
the same license change to the TQMa64xxL SoM and MBaX4XxL baseboard
Device Trees.
The copyright year is updated to indicate the license change.
Signed-off-by: Matthias Schiffer <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
In current configuration, nau8822 codec on development carrier board
provides distorted audio output. This happens due to reference clock
is fixed to 25MHz and no PLL is enabled. Following is the calculation
of deviation error for different frequencies:
44100Hz:
fs = 256 (fixed)
prescaler = 2
target frequency = 44100 * 256 * 2 = 22579200
deviation = 22579200 vs 25000000 = 9.6832%
48000Hz:
fs = 256 (fixed)
prescaler = 2
target frequency = 48000 * 256 * 2 = 24576000
deviation = 24576000 vs 25000000 = 1.696%
Enabling nau822 PLL via providing mclk-fs property to simple-audio-card
configures clocks properly, but also adjusts audio reference clock
(mclk), which in case of TI AM62 should be avoided, as it only
supports 25MHz output [1][2].
This change enables PLL on nau8822 by providing mclk-fs, and moves
away audio reference clock from DAI configuration, which prevents
simple-audio-card to adjust it before every playback [3].
[1]: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1175479/processor-sdk-am62x-output-audio_ext_refclk0-as-mclk-for-codec-and-mcbsp/4444986#4444986
[2]: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1188051/am625-audio_ext_refclk1-clock-output---dts-support/4476322#4476322
[3]: sound/soc/generic/simple-card-utils.c#L441
Signed-off-by: Andrejs Cainikovs <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Add TPM device found on Verdin iMX8M Mini PID4 0090 variant.
While adding the node, rename `pinctrl_pmic_tpm_ena` to
`pinctrl_tpm_spi_cs`.
Signed-off-by: Vitor Soares <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Add audio XCVR sound card, which supports SPDIF TX & RX,
eARC RX, ARC RX functions.
HDMI_HPD is shared with the HDMI module so use pinctrl_hog.
Signed-off-by: Shengjiu Wang <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
XCVR (Audio Transceiver) is a on-chip functional module found
on i.MX8MP. It supports HDMI2.1 eARC, HDMI1.4 ARC and SPDIF.
The reset controller is provided by the audio block control driver.
Signed-off-by: Shengjiu Wang <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
i.MX8MP DHCOM rev.200
The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses
for the Fast ethernet PHYs. Update the base SoM DT to cater for this change.
Prototype rev.100 SoM was never publicly available and was manufactured in
limited series, anything currently available is rev.200 or newer, so it is
safe to update the DT this way.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The DH i.MX8M Plus DHCOM SoM uses Audio PLL2 to supply clock to CLKOUT2
output. Those clock are used to supply on-SoM TC9595 DSI-to-(e)DP bridge
with RefClk and must not be reconfigured, otherwise the bridge cannot
work correctly. Stop reconfiguring Audio PLL2 on this SoM.
Fixes: f560da940e32 ("arm64: dts: imx8mp: Initialize audio PLLs from audiomix subsystem")
Signed-off-by: Marek Vasut <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Rename b(q)man-portals to b(q)man-portals-bus to fix below CHECK_DTB
warnings.
arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dtb:
bman-portals@508000000: $nodename:0: 'bman-portals@508000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Add thermal subfix for thermal node to fix below CHECK_DTB warnings.
thermal-zones: '...' do not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$'
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
clk-name is undocument property and never used in watchdog driver. Remove
it and fix below CHECK_DTB warning.
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: watchdog@2ad0000: Unevaluated properties are not allowed ('big-endian', 'clock-names' were unexpected)
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Rename aux_bus to aux-bus to fix below CHECK_DTBS warning.
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb:
aux_bus: $nodename:0: 'aux_bus' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yam
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Change pcie interrupt order to fix below warning.
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dtb: pcie@3400000: interrupt-names:0: 'pme' was expected
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml#
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dtb: pcie@3400000: interrupt-names:1: 'aer' was expected
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml#
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Rename node name "wdt" to "watchdog" to fix below warning:
arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dtb:
wdt@c000000: $nodename:0: 'wdt@c000000' does not match '^(timer|watchdog)(@.*|-([0-9]|[1-9][0-9]+))?$
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Add #dma-cells for qdma to fix below warning.
dma-controller@8380000: '#dma-cells' is a required property
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Fman3 should use 'fsl,fman-memac-mdio'. 'fsl,fman-xmdio' is for fman2.
Fix below CHECK_DTBS warning.
fman@1a00000: mdio@eb000:compatible: ['fsl,fman-memac-mdio', 'fsl,fman-xmdio'] is too long
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Replace node name 'nor' with 'flash' to fix below CHECK_DTBS warning.
nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Workaround already applied unconditional at
commit a6ba1e453174 ("usb: dwc3: apply snps,host-vbus-glitches workaround unconditionally")
Remove it to fix CHECK_DTBS warning:
usb@2f00000: Unevaluated properties are not allowed ('snps,host-vbus-glitches' was unexpected)
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Change #addres-cells to 1 and #size-cells to 0 to align binding doc
requiremement.
Fix below warning:
arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dtb: pinmux@70010012c: #address-cells:0:0: 1 was expected
from schema $id: http://devicetree.org/schemas/pinctrl/pinctrl-single.yaml#
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Add platform special compatible string for all gpio controller to fix
below warning.
gpio@2300000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,qoriq-gpio'] is too short
'fsl,qoriq-gpio' is not one of ['fsl,mpc5121-gpio', 'fsl,mpc5125-gpio', 'fsl,mpc8349-gpio', 'fsl,mpc8572-gpio', 'fsl,mpc8610-gpio', 'fsl,pq3-gpio']
'fsl,qoriq-gpio' is not one of ['fsl,ls1021a-gpio', 'fsl,ls1028a-gpio', 'fsl,ls1043a-gpio', 'fsl,ls1088a-gpio', 'fsl,ls2080a-gpio']
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
ftm_alarm is rtc. Correct the name as 'rtc' to fix DTB_CHECK warning.
timer@29d0000: $nodename:0: 'timer@29d0000' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/fsl,ls-ftm-alarm.yaml
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
According to fsl,dsp.yaml, 'memory-region' is a required property.
Pass 'memory-region' to fix the following dt-schema warning:
imx8qxp-mek.dtb: dsp@596e8000: 'memory-region' is a required property
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Add PCIe[0,1] and all dependent nodes.
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Add lpi2c7 and expander gpio pcal6524.
Signed-off-by: Frank Li <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Add pcie[0,1] and pcie-ep[0,1] support.
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Add '#address-cells' and '#size-cells' for all I2C to avoid duplicate these
at every board files.
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Use SPI common properties 'spi-cs-setup-delay-ns' and
'spi-cs-hold-delay-ns', mark private properties 'fsl,spi-cs-sck-delay'
and 'fsl,spi-sck-cs-delay' as deprecated.
Signed-off-by: Frank Li <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Reorder lpi2c2, lpi2c3, mu1 and mu2 label in alphabetical order.
Signed-off-by: Joy Zou <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Move node "rtc@53" to existed "&lpi2c3" and remove redundant
"&lpi2c3" label.
Signed-off-by: Joy Zou <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
i.MX fixes for 6.10:
- Fix GPIO number for reg_usdhc2_vmmc on imx8qm-mek board.
- Enable hysteresis for SODIMM_17 pin on imx8mm-verdin board to increase
immunity against noise.
- Remove 'no-sdio' property for uSDHC2 on imx93-11x11-evk board, so that
SDIO cards could also work.
- Fix BT shutdown GPIO for imx8mp-venice-gw73xx-2x board.
- Fix panel node deleting on imx53-qsb-hdmi, as /delete-node/ directive
doesn't really delete a node in a DT overlay.
- Fix TC9595 input clock on DH i.MX8M Plus DHCOM SoM.
- Fix GPU speed for imx8mm-verdin board by enabling overdrive mode in
the SOM dtsi.
|
|
The various pgv_vpu nodes have a mismatch between the value after
the @ symbol and what is referenced by 'reg' so reorder the nodes
to align.
Fixes: df680992dd62 ("arm64: dts: imx8mp: add vpu pgc nodes")
Suggested-by: Alexander Stein <[email protected]>
Signed-off-by: Adam Ford <[email protected]>
Reviewd-by: Alexander Stein <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The GW7400 has an onboard DP83867 RGMII GbE PHY:
- add RGMII delay and FIFO configuration
- add LED configuration required to use them via netdev trigger:
two LED's (LED1 and LED2, skipping LED0).
Signed-off-by: Tim Harvey <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The GW702x SoM has an onboard DP83867 RGMII GbE PHY that drives two
LED's (LED1 and LED2, skipping LED0). Add the appropriate dt bindings to
allow these PHY LED's to be controlled via a netdev trigger.
Signed-off-by: Tim Harvey <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The GW700x SoM has an onboard DP83867 RGMII GbE PHY that drives two
LED's (LED1 and LED2, skipping LED0). Add the appropriate dt bindings to
allow these PHY LED's to be controlled via a netdev trigger.
Signed-off-by: Tim Harvey <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Fix the dt-schema warnings due to #address-cells/#size-cells being
unnecessary when there are no children with reg cells.
Signed-off-by: Tim Harvey <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
The pgc_mlmix shows a power-domain@24, but the reg value is
IMX8MP_POWER_DOMAIN_MLMIX which is set to 4.
The stuff after the @ symbol should match the stuff referenced
by 'reg' so reorder the pgc_mlmix so it to appear as power-domain@4.
Fixes: 834464c8504c ("arm64: dts: imx8mp: add mlmix power domain")
Fixes: 4bedc468b725 ("arm64: dts: imx8mp: Add NPU Node")
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Alexander Stein <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
Add imx8dxl_cm4, lsio mu5 and related memory region.
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
This adds support for TQMa8MPQL module on MBa8MP-RAS314 board.
Signed-off-by: Martin Schmiedel <[email protected]>
Signed-off-by: Alexander Stein <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into soc/dt
Amlogic ARM64 DT changes for v6.11:
- New Boards:
- OSMC Vero 4K
- Dreambox One & Two
- GXLX/S905L p271 Reference Boards
- Amlogic A4 Power Domain
- A bunch of DT fixes to allmost solve all remaining check errors
- Amlogic S4 PWM
- Fixes for:
- SM1 SPDIF compatibles
- Bump G12 SPDIF driver strength
- Add power domain to HDMI TX
- Correct HDMI TX clocks
* tag 'amlogic-arm64-dt-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux: (32 commits)
arm64: dts: amlogic: setup hdmi system clock
arm64: dts: amlogic: gx: correct hdmi clocks
arm64: dts: amlogic: Add Amlogic S4 PWM
arm64: dts: amlogic: add power domain to hdmitx
arm64: dts: amlogic: g12: bump spdif output drive strength
arm64: dts: amlogic: sm1: fix spdif compatibles
arm64: dts: amlogic: ad402: fix thermal zone node name
arm64: dts: meson: add initial support for Dreambox One/Two
dt-bindings: arm: amlogic: add support for Dreambox One/Two
dt-bindings: add dream vendor prefix
arm64: dts: meson: add support for OSMC Vero 4K
dt-bindings: arm: amlogic: add OSMC Vero 4K
arm64: dts: amlogic: gxbb-odroidc2: fix invalid reset-gpio property
arm64: dts: amlogic: a1: drop the invalid reset-name for usb@fe004400
arm64: dts: amlogic: a1: use correct node name for mmc controller
arm64: dts: amlogic: c3: use correct compatible for gpio_intc node
arm64: dts: amlogic: axg: fix tdm audio-controller clock order
arm64: dts: amlogic: g12a-u200: add missing AVDD-supply to acodec
arm64: dts: amlogic: g12a-u200: drop invalid sound-dai-cells
arm64: dts: amlogic: sm1: fix tdm controllers compatible
...
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
With the recent defining of preferred naming for fixed clock and
regulator nodes, convert the Arm Ltd. boards to use the preferred
names. In the cases which had a unit-address, warnings about missing
"reg" property are fixed.
Signed-off-by: Rob Herring (Arm) <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Reviewed-by: Sudeep Holla <[email protected]>
Link: https://lore.kernel.org/[email protected]
Signed-off-by: Linus Walleij <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip ARM64 device tree updates for v6.11
It contains:
- cleanups for simple-bus nodes to comply with dtbs_check
* tag 'microchip-dt64-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
arm64: dts: microchip: sparx5_pcb135: move non-MMIO nodes out of axi
arm64: dts: microchip: sparx5_pcb134: move non-MMIO nodes out of axi
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Now that we have the MCU device-tree node, which acts as a GPIO
controller, add GPIO key node for the front button.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Reviewed-by: Conor Dooley <[email protected]>
Acked-by: Bartosz Golaszewski <[email protected]>
Acked-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Turris Omnia's MCU provides various features that can be configured over
I2C at address 0x2a. Add device-tree node.
This does not carry a Fixes tag - we do not want this to get backported
to stable kernels for the following reason: U-Boot since v2022.10
inserts a phy-reset-gpio property into the WAN ethernet node pointing to
the MCU node if it finds the MCU node with a cznic,turris-omnia-mcu
compatible. Thus if this change got backported to a stable kernel, the
WAN interface driver would defer probe indefinitely (since it would wait
for the turris-omnia-mcu driver which would not be present).
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Reviewed-by: Conor Dooley <[email protected]>
Acked-by: Bartosz Golaszewski <[email protected]>
Acked-by: Alexandre Belloni <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
* tag 'renesas-dts-for-v6.11-tag2-v2' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a779h0: R-Car Sound support
arm64: dts: renesas: r8a779g0: Tidy up sound DT settings
arm64: dts: renesas: Add interrupt-names to arch timer nodes
ARM: dts: renesas: Add interrupt-names to arch timer nodes
arm64: dts: renesas: r9a08g045: Add missing hypervisor virtual timer IRQ
arm64: dts: renesas: r9a07g054: Add missing hypervisor virtual timer IRQ
arm64: dts: renesas: r9a07g044: Add missing hypervisor virtual timer IRQ
arm64: dts: renesas: r9a07g043u: Add missing hypervisor virtual timer IRQ
arm64: dts: renesas: r8a779g0: Add missing hypervisor virtual timer IRQ
arm64: dts: renesas: r8a779f0: Add missing hypervisor virtual timer IRQ
arm64: dts: renesas: r8a779a0: Add missing hypervisor virtual timer IRQ
arm64: dts: renesas: r8a779h0: Drop "opp-shared" from opp-table-0
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
Add True Random Number Generator (TRNG) node to Exynos850 SoC dtsi.
Signed-off-by: Sam Protsenko <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Krzysztof Kozlowski <[email protected]>
|
|
Add PCIe dts configuraion for JH7110 SoC platform. The Star64 only has
one exposed PCIe port, so only the Mars and VisionFive 2 get two
enabled.
Signed-off-by: Minda Chen <[email protected]>
Reviewed-by: Hal Feng <[email protected]>
[conor: squash in star64's single exposed port]
Signed-off-by: Conor Dooley <[email protected]>
|
|
Add sound support for R-Car V4M.
[Kuninori: adjusted to latest upstream kernel]
Co-developed-by: Khanh Le <[email protected]>
Signed-off-by: Khanh Le <[email protected]>
Signed-off-by: Kuninori Morimoto <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/[email protected]
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
R-Car V4H (R8A779G0) supports only 1 AUDIO_CLKOUT and 1 SSI,
thus, #clock-cells / #sound-dai-cells are both fixed to zero.
(#sound-dai-cells is needed for Simple-Audio-Card, but not needed for
Audio-Graph-Card). Fix this up.
Signed-off-by: Kuninori Morimoto <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/[email protected]
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
Add interrupt-names properties to device nodes that represent ARM
architected timers for clarity.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/e5e2767011322daaebcc8dd6ecfcadc6966042d5.1718890849.git.geert+renesas@glider.be
|
|
Add interrupt-names properties to device nodes that represent ARM
architected timers for clarity.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/b964e2f916cc23b6272e158c7b24597c971a82a5.1718890849.git.geert+renesas@glider.be
|