diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/linux/acpi_amd_wbrf.h | 91 | ||||
| -rw-r--r-- | include/net/cfg80211.h | 99 | ||||
| -rw-r--r-- | include/net/mac80211.h | 23 | ||||
| -rw-r--r-- | include/uapi/linux/nl80211.h | 136 |
4 files changed, 288 insertions, 61 deletions
diff --git a/include/linux/acpi_amd_wbrf.h b/include/linux/acpi_amd_wbrf.h new file mode 100644 index 000000000000..898f31d536d4 --- /dev/null +++ b/include/linux/acpi_amd_wbrf.h @@ -0,0 +1,91 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Wifi Band Exclusion Interface (AMD ACPI Implementation) + * Copyright (C) 2023 Advanced Micro Devices + */ + +#ifndef _ACPI_AMD_WBRF_H +#define _ACPI_AMD_WBRF_H + +#include <linux/device.h> +#include <linux/notifier.h> + +/* The maximum number of frequency band ranges */ +#define MAX_NUM_OF_WBRF_RANGES 11 + +/* Record actions */ +#define WBRF_RECORD_ADD 0x0 +#define WBRF_RECORD_REMOVE 0x1 + +/** + * struct freq_band_range - Wifi frequency band range definition + * @start: start frequency point (in Hz) + * @end: end frequency point (in Hz) + */ +struct freq_band_range { + u64 start; + u64 end; +}; + +/** + * struct wbrf_ranges_in_out - wbrf ranges info + * @num_of_ranges: total number of band ranges in this struct + * @band_list: array of Wifi band ranges + */ +struct wbrf_ranges_in_out { + u64 num_of_ranges; + struct freq_band_range band_list[MAX_NUM_OF_WBRF_RANGES]; +}; + +/** + * enum wbrf_notifier_actions - wbrf notifier actions index + * @WBRF_CHANGED: there was some frequency band updates. The consumers + * should retrieve the latest active frequency bands. + */ +enum wbrf_notifier_actions { + WBRF_CHANGED, +}; + +#if IS_ENABLED(CONFIG_AMD_WBRF) +bool acpi_amd_wbrf_supported_producer(struct device *dev); +int acpi_amd_wbrf_add_remove(struct device *dev, uint8_t action, struct wbrf_ranges_in_out *in); +bool acpi_amd_wbrf_supported_consumer(struct device *dev); +int amd_wbrf_retrieve_freq_band(struct device *dev, struct wbrf_ranges_in_out *out); +int amd_wbrf_register_notifier(struct notifier_block *nb); +int amd_wbrf_unregister_notifier(struct notifier_block *nb); +#else +static inline +bool acpi_amd_wbrf_supported_consumer(struct device *dev) +{ + return false; +} + +static inline +int acpi_amd_wbrf_add_remove(struct device *dev, uint8_t action, struct wbrf_ranges_in_out *in) +{ + return -ENODEV; +} + +static inline +bool acpi_amd_wbrf_supported_producer(struct device *dev) +{ + return false; +} +static inline +int amd_wbrf_retrieve_freq_band(struct device *dev, struct wbrf_ranges_in_out *out) +{ + return -ENODEV; +} +static inline +int amd_wbrf_register_notifier(struct notifier_block *nb) +{ + return -ENODEV; +} +static inline +int amd_wbrf_unregister_notifier(struct notifier_block *nb) +{ + return -ENODEV; +} +#endif /* CONFIG_AMD_WBRF */ + +#endif /* _ACPI_AMD_WBRF_H */ diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 1b3345129a95..ac1fb326dcda 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -52,7 +52,7 @@ * such wiphy can have zero, one, or many virtual interfaces associated with * it, which need to be identified as such by pointing the network interface's * @ieee80211_ptr pointer to a &struct wireless_dev which further describes - * the wireless part of the interface, normally this struct is embedded in the + * the wireless part of the interface. Normally this struct is embedded in the * network interface's private data area. Drivers can optionally allow creating * or destroying virtual interfaces on the fly, but without at least one or the * ability to create some the wireless device isn't useful. @@ -977,6 +977,15 @@ cfg80211_chandef_compatible(const struct cfg80211_chan_def *chandef1, const struct cfg80211_chan_def *chandef2); /** + * nl80211_chan_width_to_mhz - get the channel width in MHz + * @chan_width: the channel width from &enum nl80211_chan_width + * + * Return: channel width in MHz if the chan_width from &enum nl80211_chan_width + * is valid. -1 otherwise. + */ +int nl80211_chan_width_to_mhz(enum nl80211_chan_width chan_width); + +/** * cfg80211_chandef_valid - check if a channel definition is valid * @chandef: the channel definition to check * Return: %true if the channel definition is valid. %false otherwise. @@ -1665,6 +1674,21 @@ struct link_station_del_parameters { }; /** + * struct cfg80211_ttlm_params: TID to link mapping parameters + * + * Used for setting a TID to link mapping. + * + * @dlink: Downlink TID to link mapping, as defined in section 9.4.2.314 + * (TID-To-Link Mapping element) in Draft P802.11be_D4.0. + * @ulink: Uplink TID to link mapping, as defined in section 9.4.2.314 + * (TID-To-Link Mapping element) in Draft P802.11be_D4.0. + */ +struct cfg80211_ttlm_params { + u16 dlink[8]; + u16 ulink[8]; +}; + +/** * struct station_parameters - station parameters * * Used to change and create a new station. @@ -2560,7 +2584,7 @@ struct cfg80211_scan_info { * @short_ssid: short ssid to scan for * @bssid: bssid to scan for * @channel_idx: idx of the channel in the channel array in the scan request - * which the above info relvant to + * which the above info is relevant to * @unsolicited_probe: the AP transmits unsolicited probe response every 20 TU * @short_ssid_valid: @short_ssid is valid and can be used * @psc_no_listen: when set, and the channel is a PSC channel, no need to wait @@ -2819,6 +2843,13 @@ enum cfg80211_signal_type { * the BSS that requested the scan in which the beacon/probe was received. * @chains: bitmask for filled values in @chain_signal. * @chain_signal: per-chain signal strength of last received BSS in dBm. + * @restrict_use: restrict usage, if not set, assume @use_for is + * %NL80211_BSS_USE_FOR_NORMAL. + * @use_for: bitmap of possible usage for this BSS, see + * &enum nl80211_bss_use_for + * @cannot_use_reasons: the reasons (bitmap) for not being able to connect, + * if @restrict_use is set and @use_for is zero (empty); may be 0 for + * unspecified reasons; see &enum nl80211_bss_cannot_use_reasons * @drv_data: Data to be passed through to @inform_bss */ struct cfg80211_inform_bss { @@ -2830,6 +2861,9 @@ struct cfg80211_inform_bss { u8 chains; s8 chain_signal[IEEE80211_MAX_CHAINS]; + u8 restrict_use:1, use_for:7; + u8 cannot_use_reasons; + void *drv_data; }; @@ -2881,6 +2915,11 @@ struct cfg80211_bss_ies { * @chain_signal: per-chain signal strength of last received BSS in dBm. * @bssid_index: index in the multiple BSS set * @max_bssid_indicator: max number of members in the BSS set + * @use_for: bitmap of possible usage for this BSS, see + * &enum nl80211_bss_use_for + * @cannot_use_reasons: the reasons (bitmap) for not being able to connect, + * if @restrict_use is set and @use_for is zero (empty); may be 0 for + * unspecified reasons; see &enum nl80211_bss_cannot_use_reasons * @priv: private area for driver use, has at least wiphy->bss_priv_size bytes */ struct cfg80211_bss { @@ -2906,6 +2945,9 @@ struct cfg80211_bss { u8 bssid_index; u8 max_bssid_indicator; + u8 use_for; + u8 cannot_use_reasons; + u8 priv[] __aligned(sizeof(void *)); }; @@ -4496,6 +4538,7 @@ struct mgmt_frame_regs { * @del_link_station: Remove a link of a station. * * @set_hw_timestamp: Enable/disable HW timestamping of TM/FTM frames. + * @set_ttlm: set the TID to link mapping. */ struct cfg80211_ops { int (*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow); @@ -4855,6 +4898,8 @@ struct cfg80211_ops { struct link_station_del_parameters *params); int (*set_hw_timestamp)(struct wiphy *wiphy, struct net_device *dev, struct cfg80211_set_hw_timestamp *hwts); + int (*set_ttlm)(struct wiphy *wiphy, struct net_device *dev, + struct cfg80211_ttlm_params *params); }; /* @@ -4913,6 +4958,8 @@ struct cfg80211_ops { * NL80211_REGDOM_SET_BY_DRIVER. * @WIPHY_FLAG_CHANNEL_CHANGE_ON_BEACON: reg_call_notifier() is called if driver * set this flag to update channels on beacon hints. + * @WIPHY_FLAG_SUPPORTS_NSTR_NONPRIMARY: support connection to non-primary link + * of an NSTR mobile AP MLD. */ enum wiphy_flags { WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK = BIT(0), @@ -4926,7 +4973,7 @@ enum wiphy_flags { WIPHY_FLAG_IBSS_RSN = BIT(8), WIPHY_FLAG_MESH_AUTH = BIT(10), WIPHY_FLAG_SUPPORTS_EXT_KCK_32 = BIT(11), - /* use hole at 12 */ + WIPHY_FLAG_SUPPORTS_NSTR_NONPRIMARY = BIT(12), WIPHY_FLAG_SUPPORTS_FW_ROAM = BIT(13), WIPHY_FLAG_AP_UAPSD = BIT(14), WIPHY_FLAG_SUPPORTS_TDLS = BIT(15), @@ -7165,6 +7212,25 @@ cfg80211_inform_bss(struct wiphy *wiphy, } /** + * __cfg80211_get_bss - get a BSS reference + * @wiphy: the wiphy this BSS struct belongs to + * @channel: the channel to search on (or %NULL) + * @bssid: the desired BSSID (or %NULL) + * @ssid: the desired SSID (or %NULL) + * @ssid_len: length of the SSID (or 0) + * @bss_type: type of BSS, see &enum ieee80211_bss_type + * @privacy: privacy filter, see &enum ieee80211_privacy + * @use_for: indicates which use is intended + */ +struct cfg80211_bss *__cfg80211_get_bss(struct wiphy *wiphy, + struct ieee80211_channel *channel, + const u8 *bssid, + const u8 *ssid, size_t ssid_len, + enum ieee80211_bss_type bss_type, + enum ieee80211_privacy privacy, + u32 use_for); + +/** * cfg80211_get_bss - get a BSS reference * @wiphy: the wiphy this BSS struct belongs to * @channel: the channel to search on (or %NULL) @@ -7173,13 +7239,20 @@ cfg80211_inform_bss(struct wiphy *wiphy, * @ssid_len: length of the SSID (or 0) * @bss_type: type of BSS, see &enum ieee80211_bss_type * @privacy: privacy filter, see &enum ieee80211_privacy + * + * This version implies regular usage, %NL80211_BSS_USE_FOR_NORMAL. */ -struct cfg80211_bss *cfg80211_get_bss(struct wiphy *wiphy, - struct ieee80211_channel *channel, - const u8 *bssid, - const u8 *ssid, size_t ssid_len, - enum ieee80211_bss_type bss_type, - enum ieee80211_privacy privacy); +static inline struct cfg80211_bss * +cfg80211_get_bss(struct wiphy *wiphy, struct ieee80211_channel *channel, + const u8 *bssid, const u8 *ssid, size_t ssid_len, + enum ieee80211_bss_type bss_type, + enum ieee80211_privacy privacy) +{ + return __cfg80211_get_bss(wiphy, channel, bssid, ssid, ssid_len, + bss_type, privacy, + NL80211_BSS_USE_FOR_NORMAL); +} + static inline struct cfg80211_bss * cfg80211_get_ibss(struct wiphy *wiphy, struct ieee80211_channel *channel, @@ -7312,7 +7385,7 @@ struct cfg80211_rx_assoc_resp_data { * This function may sleep. The caller must hold the corresponding wdev's mutex. */ void cfg80211_rx_assoc_resp(struct net_device *dev, - struct cfg80211_rx_assoc_resp_data *data); + const struct cfg80211_rx_assoc_resp_data *data); /** * struct cfg80211_assoc_failure - association failure data @@ -7431,7 +7504,7 @@ void cfg80211_notify_new_peer_candidate(struct net_device *dev, * RFkill integration in cfg80211 is almost invisible to drivers, * as cfg80211 automatically registers an rfkill instance for each * wireless device it knows about. Soft kill is also translated - * into disconnecting and turning all interfaces off, drivers are + * into disconnecting and turning all interfaces off. Drivers are * expected to turn off the device when all interfaces are down. * * However, devices may have a hard RFkill line, in which case they @@ -7479,7 +7552,7 @@ static inline void wiphy_rfkill_stop_polling(struct wiphy *wiphy) * the configuration mechanism. * * A driver supporting vendor commands must register them as an array - * in struct wiphy, with handlers for each one, each command has an + * in struct wiphy, with handlers for each one. Each command has an * OUI and sub command ID to identify it. * * Note that this feature should not be (ab)used to implement protocol @@ -7643,7 +7716,7 @@ static inline void cfg80211_vendor_event(struct sk_buff *skb, gfp_t gfp) * interact with driver-specific tools to aid, for instance, * factory programming. * - * This chapter describes how drivers interact with it, for more + * This chapter describes how drivers interact with it. For more * information see the nl80211 book's chapter on it. */ diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 580781ff9dcf..77a71b1396b1 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -2686,6 +2686,9 @@ struct ieee80211_txq { * @IEEE80211_HW_MLO_MCAST_MULTI_LINK_TX: Hardware/driver handles transmitting * multicast frames on all links, mac80211 should not do that. * + * @IEEE80211_HW_DISALLOW_PUNCTURING: HW requires disabling puncturing in EHT + * and connecting with a lower bandwidth instead + * * @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays */ enum ieee80211_hw_flags { @@ -2743,6 +2746,7 @@ enum ieee80211_hw_flags { IEEE80211_HW_SUPPORTS_CONC_MON_RX_DECAP, IEEE80211_HW_DETECTS_COLOR_COLLISION, IEEE80211_HW_MLO_MCAST_MULTI_LINK_TX, + IEEE80211_HW_DISALLOW_PUNCTURING, /* keep last, obviously */ NUM_IEEE80211_HW_FLAGS @@ -5809,12 +5813,11 @@ void ieee80211_set_key_rx_seq(struct ieee80211_key_conf *keyconf, * ieee80211_remove_key - remove the given key * @keyconf: the parameter passed with the set key * + * Context: Must be called with the wiphy mutex held. + * * Remove the given key. If the key was uploaded to the hardware at the * time this function is called, it is not deleted in the hardware but * instead assumed to have been removed already. - * - * Note that due to locking considerations this function can (currently) - * only be called during key iteration (ieee80211_iter_keys().) */ void ieee80211_remove_key(struct ieee80211_key_conf *keyconf); @@ -6368,12 +6371,12 @@ ieee80211_txq_airtime_check(struct ieee80211_hw *hw, struct ieee80211_txq *txq); * @iter: iterator function that will be called for each key * @iter_data: custom data to pass to the iterator function * + * Context: Must be called with wiphy mutex held; can sleep. + * * This function can be used to iterate all the keys known to * mac80211, even those that weren't previously programmed into * the device. This is intended for use in WoWLAN if the device - * needs reprogramming of the keys during suspend. Note that due - * to locking reasons, it is also only safe to call this at few - * spots since it must hold the RTNL and be able to sleep. + * needs reprogramming of the keys during suspend. * * The order in which the keys are iterated matches the order * in which they were originally installed and handed to the @@ -7435,6 +7438,9 @@ static inline bool ieee80211_is_tx_data(struct sk_buff *skb) * @vif: interface to set active links on * @active_links: the new active links bitmap * + * Context: Must be called with wiphy mutex held; may sleep; calls + * back into the driver. + * * This changes the active links on an interface. The interface * must be in client mode (in AP mode, all links are always active), * and @active_links must be a subset of the vif's valid_links. @@ -7442,6 +7448,7 @@ static inline bool ieee80211_is_tx_data(struct sk_buff *skb) * If a link is switched off and another is switched on at the same * time (e.g. active_links going from 0x1 to 0x10) then you will get * a sequence of calls like + * * - change_vif_links(0x11) * - unassign_vif_chanctx(link_id=0) * - change_sta_links(0x11) for each affected STA (the AP) @@ -7451,10 +7458,6 @@ static inline bool ieee80211_is_tx_data(struct sk_buff *skb) * - change_sta_links(0x10) for each affected STA (the AP) * - assign_vif_chanctx(link_id=4) * - change_vif_links(0x10) - * - * Note: This function acquires some mac80211 locks and must not - * be called with any driver locks held that could cause a - * lock dependency inversion. Best call it without locks. */ int ieee80211_set_active_links(struct ieee80211_vif *vif, u16 active_links); diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index 0cd1da2c2902..a682b54bd3ba 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -72,7 +72,7 @@ * For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS * and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows: * - a setup station entry is added, not yet authorized, without any rate - * or capability information, this just exists to avoid race conditions + * or capability information; this just exists to avoid race conditions * - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid * to add rate and capability information to the station and at the same * time mark it authorized. @@ -87,7 +87,7 @@ * DOC: Frame transmission/registration support * * Frame transmission and registration support exists to allow userspace - * management entities such as wpa_supplicant react to management frames + * management entities such as wpa_supplicant to react to management frames * that are not being handled by the kernel. This includes, for example, * certain classes of action frames that cannot be handled in the kernel * for various reasons. @@ -113,7 +113,7 @@ * * Frame transmission allows userspace to send for example the required * responses to action frames. It is subject to some sanity checking, - * but many frames can be transmitted. When a frame was transmitted, its + * but many frames can be transmitted. When a frame is transmitted, its * status is indicated to the sending socket. * * For more technical details, see the corresponding command descriptions @@ -123,7 +123,7 @@ /** * DOC: Virtual interface / concurrency capabilities * - * Some devices are able to operate with virtual MACs, they can have + * Some devices are able to operate with virtual MACs; they can have * more than one virtual interface. The capability handling for this * is a bit complex though, as there may be a number of restrictions * on the types of concurrency that are supported. @@ -135,7 +135,7 @@ * Once concurrency is desired, more attributes must be observed: * To start with, since some interface types are purely managed in * software, like the AP-VLAN type in mac80211 for example, there's - * an additional list of these, they can be added at any time and + * an additional list of these; they can be added at any time and * are only restricted by some semantic restrictions (e.g. AP-VLAN * cannot be added without a corresponding AP interface). This list * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute. @@ -164,7 +164,7 @@ * Packet coalesce feature helps to reduce number of received interrupts * to host by buffering these packets in firmware/hardware for some * predefined time. Received interrupt will be generated when one of the - * following events occur. + * following events occurs. * a) Expiration of hardware timer whose expiration time is set to maximum * coalescing delay of matching coalesce rule. * b) Coalescing buffer in hardware reaches its limit. @@ -174,7 +174,7 @@ * rule. * a) Maximum coalescing delay * b) List of packet patterns which needs to be matched - * c) Condition for coalescence. pattern 'match' or 'no match' + * c) Condition for coalescence: pattern 'match' or 'no match' * Multiple such rules can be created. */ @@ -213,7 +213,7 @@ /** * DOC: FILS shared key authentication offload * - * FILS shared key authentication offload can be advertized by drivers by + * FILS shared key authentication offload can be advertised by drivers by * setting @NL80211_EXT_FEATURE_FILS_SK_OFFLOAD flag. The drivers that support * FILS shared key authentication offload should be able to construct the * authentication and association frames for FILS shared key authentication and @@ -239,7 +239,7 @@ * The PMKSA can be maintained in userspace persistently so that it can be used * later after reboots or wifi turn off/on also. * - * %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertized by a FILS + * %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertised by a FILS * capable AP supporting PMK caching. It specifies the scope within which the * PMKSAs are cached in an ESS. %NL80211_CMD_SET_PMKSA and * %NL80211_CMD_DEL_PMKSA are enhanced to allow support for PMKSA caching based @@ -290,12 +290,12 @@ * If the configuration needs to be applied for specific peer then the MAC * address of the peer needs to be passed in %NL80211_ATTR_MAC, otherwise the * configuration will be applied for all the connected peers in the vif except - * any peers that have peer specific configuration for the TID by default; if - * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer specific values + * any peers that have peer-specific configuration for the TID by default; if + * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer-specific values * will be overwritten. * - * All this configuration is valid only for STA's current connection - * i.e. the configuration will be reset to default when the STA connects back + * All this configuration is valid only for STA's current connection, + * i.e., the configuration will be reset to default when the STA connects back * after disconnection/roaming, and this configuration will be cleared when * the interface goes down. */ @@ -521,7 +521,7 @@ * %NL80211_ATTR_SCHED_SCAN_PLANS. If %NL80211_ATTR_SCHED_SCAN_PLANS is * not specified and only %NL80211_ATTR_SCHED_SCAN_INTERVAL is specified, * scheduled scan will run in an infinite loop with the specified interval. - * These attributes are mutually exculsive, + * These attributes are mutually exclusive, * i.e. NL80211_ATTR_SCHED_SCAN_INTERVAL must not be passed if * NL80211_ATTR_SCHED_SCAN_PLANS is defined. * If for some reason scheduled scan is aborted by the driver, all scan @@ -552,7 +552,7 @@ * %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface * is brought down while a scheduled scan was running. * - * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation + * @NL80211_CMD_GET_SURVEY: get survey results, e.g. channel occupation * or noise level * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to * NL80211_CMD_GET_SURVEY and on the "scan" multicast group) @@ -563,12 +563,13 @@ * using %NL80211_ATTR_SSID, %NL80211_ATTR_FILS_CACHE_ID, * %NL80211_ATTR_PMKID, and %NL80211_ATTR_PMK in case of FILS * authentication where %NL80211_ATTR_FILS_CACHE_ID is the identifier - * advertized by a FILS capable AP identifying the scope of PMKSA in an + * advertised by a FILS capable AP identifying the scope of PMKSA in an * ESS. * @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC * (for the BSSID) and %NL80211_ATTR_PMKID or using %NL80211_ATTR_SSID, * %NL80211_ATTR_FILS_CACHE_ID, and %NL80211_ATTR_PMKID in case of FILS - * authentication. + * authentication. Additionally in case of SAE offload and OWE offloads + * PMKSA entry can be deleted using %NL80211_ATTR_SSID. * @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries. * * @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain @@ -607,7 +608,7 @@ * BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify * the SSID (mainly for association, but is included in authentication * request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ + - * %NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequence of the + * %NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequency of the * channel in MHz. %NL80211_ATTR_AUTH_TYPE is used to specify the * authentication type. %NL80211_ATTR_IE is used to define IEs * (VendorSpecificInfo, but also including RSN IE and FT IEs) to be added @@ -816,7 +817,7 @@ * reached. * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ * and the attributes determining channel width) the given interface - * (identifed by %NL80211_ATTR_IFINDEX) shall operate on. + * (identified by %NL80211_ATTR_IFINDEX) shall operate on. * In case multiple channels are supported by the device, the mechanism * with which it switches channels is implementation-defined. * When a monitor interface is given, it can only switch channel while @@ -888,7 +889,7 @@ * inform userspace of the new replay counter. * * @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace - * of PMKSA caching dandidates. + * of PMKSA caching candidates. * * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup). * In addition, this can be used as an event to request userspace to take @@ -924,7 +925,7 @@ * * @NL80211_CMD_PROBE_CLIENT: Probe an associated station on an AP interface * by sending a null data frame to it and reporting when the frame is - * acknowleged. This is used to allow timing out inactive clients. Uses + * acknowledged. This is used to allow timing out inactive clients. Uses * %NL80211_ATTR_IFINDEX and %NL80211_ATTR_MAC. The command returns a * direct reply with an %NL80211_ATTR_COOKIE that is later used to match * up the event with the request. The event includes the same data and @@ -1327,6 +1328,11 @@ * Multi-Link reconfiguration. %NL80211_ATTR_MLO_LINKS is used to provide * information about the removed STA MLD setup links. * + * @NL80211_CMD_SET_TID_TO_LINK_MAPPING: Set the TID to Link Mapping for a + * non-AP MLD station. The %NL80211_ATTR_MLO_TTLM_DLINK and + * %NL80211_ATTR_MLO_TTLM_ULINK attributes are used to specify the + * TID to Link mapping for downlink/uplink traffic. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -1582,6 +1588,8 @@ enum nl80211_commands { NL80211_CMD_LINKS_REMOVED, + NL80211_CMD_SET_TID_TO_LINK_MAPPING, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -1839,7 +1847,7 @@ enum nl80211_commands { * using %CMD_CONTROL_PORT_FRAME. If control port routing over NL80211 is * to be used then userspace must also use the %NL80211_ATTR_SOCKET_OWNER * flag. When used with %NL80211_ATTR_CONTROL_PORT_NO_PREAUTH, pre-auth - * frames are not forwared over the control port. + * frames are not forwarded over the control port. * * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver. * We recommend using nested, driver-specific attributes within this. @@ -1976,10 +1984,10 @@ enum nl80211_commands { * bit. Depending on which antennas are selected in the bitmap, 802.11n * drivers can derive which chainmasks to use (if all antennas belonging to * a particular chain are disabled this chain should be disabled) and if - * a chain has diversity antennas wether diversity should be used or not. + * a chain has diversity antennas whether diversity should be used or not. * HT capabilities (STBC, TX Beamforming, Antenna selection) can be * derived from the available chains after applying the antenna mask. - * Non-802.11n drivers can derive wether to use diversity or not. + * Non-802.11n drivers can derive whether to use diversity or not. * Drivers may reject configurations or RX/TX mask combinations they cannot * support by returning -EINVAL. * @@ -2549,7 +2557,7 @@ enum nl80211_commands { * from successful FILS authentication and is used with * %NL80211_CMD_CONNECT. * - * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertized by a FILS AP + * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertised by a FILS AP * identifying the scope of PMKSAs. This is used with * @NL80211_CMD_SET_PMKSA and @NL80211_CMD_DEL_PMKSA. * @@ -2830,6 +2838,19 @@ enum nl80211_commands { * @NL80211_ATTR_MLO_LINK_DISABLED: Flag attribute indicating that the link is * disabled. * + * @NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA: Include BSS usage data, i.e. + * include BSSes that can only be used in restricted scenarios and/or + * cannot be used at all. + * + * @NL80211_ATTR_MLO_TTLM_DLINK: Binary attribute specifying the downlink TID to + * link mapping. The length is 8 * sizeof(u16). For each TID the link + * mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element) + * in Draft P802.11be_D4.0. + * @NL80211_ATTR_MLO_TTLM_ULINK: Binary attribute specifying the uplink TID to + * link mapping. The length is 8 * sizeof(u16). For each TID the link + * mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element) + * in Draft P802.11be_D4.0. + * * @NUM_NL80211_ATTR: total number of nl80211_attrs available * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use @@ -3368,6 +3389,11 @@ enum nl80211_attrs { NL80211_ATTR_MLO_LINK_DISABLED, + NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA, + + NL80211_ATTR_MLO_TTLM_DLINK, + NL80211_ATTR_MLO_TTLM_ULINK, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -4174,7 +4200,7 @@ enum nl80211_wmm_rule { * (100 * dBm). * @NL80211_FREQUENCY_ATTR_DFS_STATE: current state for DFS * (enum nl80211_dfs_state) - * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in miliseconds for how long + * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in milliseconds for how long * this channel is in this DFS state. * @NL80211_FREQUENCY_ATTR_NO_HT40_MINUS: HT40- isn't possible with this * channel as the control channel @@ -5032,6 +5058,30 @@ enum nl80211_bss_scan_width { }; /** + * enum nl80211_bss_use_for - bitmap indicating possible BSS use + * @NL80211_BSS_USE_FOR_NORMAL: Use this BSS for normal "connection", + * including IBSS/MBSS depending on the type. + * @NL80211_BSS_USE_FOR_MLD_LINK: This BSS can be used as a link in an + * MLO connection. Note that for an MLO connection, all links including + * the assoc link must have this flag set, and the assoc link must + * additionally have %NL80211_BSS_USE_FOR_NORMAL set. + */ +enum nl80211_bss_use_for { + NL80211_BSS_USE_FOR_NORMAL = 1 << 0, + NL80211_BSS_USE_FOR_MLD_LINK = 1 << 1, +}; + +/** + * enum nl80211_bss_cannot_use_reasons - reason(s) connection to a + * BSS isn't possible + * @NL80211_BSS_CANNOT_USE_NSTR_NONPRIMARY: NSTR nonprimary links aren't + * supported by the device, and this BSS entry represents one. + */ +enum nl80211_bss_cannot_use_reasons { + NL80211_BSS_CANNOT_USE_NSTR_NONPRIMARY = 1 << 0, +}; + +/** * enum nl80211_bss - netlink attributes for a BSS * * @__NL80211_BSS_INVALID: invalid @@ -5083,6 +5133,14 @@ enum nl80211_bss_scan_width { * @NL80211_BSS_FREQUENCY_OFFSET: frequency offset in KHz * @NL80211_BSS_MLO_LINK_ID: MLO link ID of the BSS (u8). * @NL80211_BSS_MLD_ADDR: MLD address of this BSS if connected to it. + * @NL80211_BSS_USE_FOR: u32 bitmap attribute indicating what the BSS can be + * used for, see &enum nl80211_bss_use_for. + * @NL80211_BSS_CANNOT_USE_REASONS: Indicates the reason that this BSS cannot + * be used for all or some of the possible uses by the device reporting it, + * even though its presence was detected. + * This is a u64 attribute containing a bitmap of values from + * &enum nl80211_cannot_use_reasons, note that the attribute may be missing + * if no reasons are specified. * @__NL80211_BSS_AFTER_LAST: internal * @NL80211_BSS_MAX: highest BSS attribute */ @@ -5110,6 +5168,8 @@ enum nl80211_bss { NL80211_BSS_FREQUENCY_OFFSET, NL80211_BSS_MLO_LINK_ID, NL80211_BSS_MLD_ADDR, + NL80211_BSS_USE_FOR, + NL80211_BSS_CANNOT_USE_REASONS, /* keep last */ __NL80211_BSS_AFTER_LAST, @@ -5458,7 +5518,7 @@ enum nl80211_tx_rate_setting { * (%NL80211_TID_CONFIG_ATTR_TIDS, %NL80211_TID_CONFIG_ATTR_OVERRIDE). * @NL80211_TID_CONFIG_ATTR_PEER_SUPP: same as the previous per-vif one, but * per peer instead. - * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribue, if set indicates + * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribute, if set indicates * that the new configuration overrides all previous peer * configurations, otherwise previous peer specific configurations * should be left untouched. @@ -5841,7 +5901,7 @@ enum nl80211_attr_coalesce_rule { /** * enum nl80211_coalesce_condition - coalesce rule conditions - * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns + * @NL80211_COALESCE_CONDITION_MATCH: coalesce Rx packets when patterns * in a rule are matched. * @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns * in a rule are not matched. @@ -5940,7 +6000,7 @@ enum nl80211_if_combination_attrs { * enum nl80211_plink_state - state of a mesh peer link finite state machine * * @NL80211_PLINK_LISTEN: initial state, considered the implicit - * state of non existent mesh peer links + * state of non-existent mesh peer links * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to * this mesh peer * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received @@ -6233,7 +6293,7 @@ enum nl80211_feature_flags { * request to use RRM (see %NL80211_ATTR_USE_RRM) with * %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests, which will set * the ASSOC_REQ_USE_RRM flag in the association request even if - * NL80211_FEATURE_QUIET is not advertized. + * NL80211_FEATURE_QUIET is not advertised. * @NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER: This device supports MU-MIMO air * sniffer which means that it can be configured to hear packets from * certain groups which can be configured by the @@ -6245,7 +6305,7 @@ enum nl80211_feature_flags { * the BSS that the interface that requested the scan is connected to * (if available). * @NL80211_EXT_FEATURE_BSS_PARENT_TSF: Per BSS, this driver reports the - * time the last beacon/probe was received. For a non MLO connection, the + * time the last beacon/probe was received. For a non-MLO connection, the * time is the TSF of the BSS that the interface that requested the scan is * connected to (if available). For an MLO connection, the time is the TSF * of the BSS corresponding with link ID specified in the scan request (if @@ -6253,7 +6313,7 @@ enum nl80211_feature_flags { * @NL80211_EXT_FEATURE_SET_SCAN_DWELL: This driver supports configuration of * channel dwell time. * @NL80211_EXT_FEATURE_BEACON_RATE_LEGACY: Driver supports beacon rate - * configuration (AP/mesh), supporting a legacy (non HT/VHT) rate. + * configuration (AP/mesh), supporting a legacy (non-HT/VHT) rate. * @NL80211_EXT_FEATURE_BEACON_RATE_HT: Driver supports beacon rate * configuration (AP/mesh) with HT rates. * @NL80211_EXT_FEATURE_BEACON_RATE_VHT: Driver supports beacon rate @@ -6589,7 +6649,7 @@ enum nl80211_timeout_reason { * request parameters IE in the probe request * @NL80211_SCAN_FLAG_ACCEPT_BCAST_PROBE_RESP: accept broadcast probe responses * @NL80211_SCAN_FLAG_OCE_PROBE_REQ_HIGH_TX_RATE: send probe request frames at - * rate of at least 5.5M. In case non OCE AP is discovered in the channel, + * rate of at least 5.5M. In case non-OCE AP is discovered in the channel, * only the first probe req in the channel will be sent in high rate. * @NL80211_SCAN_FLAG_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION: allow probe request * tx deferral (dot11FILSProbeDelay shall be set to 15ms) @@ -6625,7 +6685,7 @@ enum nl80211_timeout_reason { * received on the 2.4/5 GHz channels to actively scan only the 6GHz * channels on which APs are expected to be found. Note that when not set, * the scan logic would scan all 6GHz channels, but since transmission of - * probe requests on non PSC channels is limited, it is highly likely that + * probe requests on non-PSC channels is limited, it is highly likely that * these channels would passively be scanned. Also note that when the flag * is set, in addition to the colocated APs, PSC channels would also be * scanned if the user space has asked for it. @@ -6957,7 +7017,7 @@ enum nl80211_nan_func_term_reason { * The instance ID for the follow up Service Discovery Frame. This is u8. * @NL80211_NAN_FUNC_FOLLOW_UP_REQ_ID: relevant if the function's type * is follow up. This is a u8. - * The requestor instance ID for the follow up Service Discovery Frame. + * The requester instance ID for the follow up Service Discovery Frame. * @NL80211_NAN_FUNC_FOLLOW_UP_DEST: the MAC address of the recipient of the * follow up Service Discovery Frame. This is a binary attribute. * @NL80211_NAN_FUNC_CLOSE_RANGE: is this function limited for devices in a @@ -7347,7 +7407,7 @@ enum nl80211_peer_measurement_attrs { * @NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED: flag attribute indicating if * trigger based ranging measurement is supported * @NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED: flag attribute indicating - * if non trigger based ranging measurement is supported + * if non-trigger-based ranging measurement is supported * * @NUM_NL80211_PMSR_FTM_CAPA_ATTR: internal * @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number @@ -7401,7 +7461,7 @@ enum nl80211_peer_measurement_ftm_capa { * if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based * ranging will be used. - * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non trigger based + * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non-trigger-based * ranging measurement (flag) * This attribute and %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED are * mutually exclusive. @@ -7479,7 +7539,7 @@ enum nl80211_peer_measurement_ftm_failure_reasons { * @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_ATTEMPTS: number of FTM Request frames * transmitted (u32, optional) * @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_SUCCESSES: number of FTM Request frames - * that were acknowleged (u32, optional) + * that were acknowledged (u32, optional) * @NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME: retry time received from the * busy peer (u32, seconds) * @NL80211_PMSR_FTM_RESP_ATTR_NUM_BURSTS_EXP: actual number of bursts exponent |