diff options
Diffstat (limited to 'drivers/usb/dwc2/core.h')
| -rw-r--r-- | drivers/usb/dwc2/core.h | 324 |
1 files changed, 103 insertions, 221 deletions
diff --git a/drivers/usb/dwc2/core.h b/drivers/usb/dwc2/core.h index 2a21a0414b1d..9548d3e03453 100644 --- a/drivers/usb/dwc2/core.h +++ b/drivers/usb/dwc2/core.h @@ -172,6 +172,11 @@ struct dwc2_hsotg_req; * @periodic: Set if this is a periodic ep, such as Interrupt * @isochronous: Set if this is a isochronous ep * @send_zlp: Set if we need to send a zero-length packet. + * @desc_list_dma: The DMA address of descriptor chain currently in use. + * @desc_list: Pointer to descriptor DMA chain head currently in use. + * @desc_count: Count of entries within the DMA descriptor chain of EP. + * @isoc_chain_num: Number of ISOC chain currently in use - either 0 or 1. + * @next_desc: index of next free descriptor in the ISOC chain under SW control. * @total_data: The total number of data bytes done. * @fifo_size: The size of the FIFO (for periodic IN endpoints) * @fifo_load: The amount of data loaded into the FIFO (periodic IN) @@ -219,6 +224,13 @@ struct dwc2_hsotg_ep { #define TARGET_FRAME_INITIAL 0xFFFFFFFF bool frame_overrun; + dma_addr_t desc_list_dma; + struct dwc2_dma_desc *desc_list; + u8 desc_count; + + unsigned char isoc_chain_num; + unsigned int next_desc; + char name[10]; }; @@ -286,7 +298,7 @@ enum dwc2_ep0_state { * @otg_ver: OTG version supported * 0 - 1.3 (default) * 1 - 2.0 - * @dma_enable: Specifies whether to use slave or DMA mode for accessing + * @host_dma: Specifies whether to use slave or DMA mode for accessing * the data FIFOs. The driver will automatically detect the * value for this parameter if none is specified. * 0 - Slave (always available) @@ -314,7 +326,8 @@ enum dwc2_ep0_state { * @enable_dynamic_fifo: 0 - Use coreConsultant-specified FIFO size parameters * 1 - Allow dynamic FIFO sizing (default, if available) * @en_multiple_tx_fifo: Specifies whether dedicated per-endpoint transmit FIFOs - * are enabled + * are enabled for non-periodic IN endpoints in device + * mode. * @host_rx_fifo_size: Number of 4-byte words in the Rx FIFO in host mode when * dynamic FIFO sizing is enabled * 16 to 32768 @@ -417,6 +430,20 @@ enum dwc2_ep0_state { * needed. * 0 - No (default) * 1 - Yes + * @g_dma: Enables gadget dma usage (default: autodetect). + * @g_dma_desc: Enables gadget descriptor DMA (default: autodetect). + * @g_rx_fifo_size: The periodic rx fifo size for the device, in + * DWORDS from 16-32768 (default: 2048 if + * possible, otherwise autodetect). + * @g_np_tx_fifo_size: The non-periodic tx fifo size for the device in + * DWORDS from 16-32768 (default: 1024 if + * possible, otherwise autodetect). + * @g_tx_fifo_size: An array of TX fifo sizes in dedicated fifo + * mode. Each value corresponds to one EP + * starting from EP1 (max 15 values). Sizes are + * in DWORDS with possible values from from + * 16-32768 (default: 256, 256, 256, 256, 768, + * 768, 768, 768, 0, 0, 0, 0, 0, 0, 0). * * The following parameters may be specified when starting the module. These * parameters define how the DWC_otg controller should be configured. A @@ -430,11 +457,18 @@ struct dwc2_core_params { * dwc2_set_all_params! */ int otg_cap; +#define DWC2_CAP_PARAM_HNP_SRP_CAPABLE 0 +#define DWC2_CAP_PARAM_SRP_ONLY_CAPABLE 1 +#define DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE 2 + int otg_ver; - int dma_enable; int dma_desc_enable; int dma_desc_fs_enable; int speed; +#define DWC2_SPEED_PARAM_HIGH 0 +#define DWC2_SPEED_PARAM_FULL 1 +#define DWC2_SPEED_PARAM_LOW 2 + int enable_dynamic_fifo; int en_multiple_tx_fifo; int host_rx_fifo_size; @@ -444,19 +478,44 @@ struct dwc2_core_params { int max_packet_count; int host_channels; int phy_type; +#define DWC2_PHY_TYPE_PARAM_FS 0 +#define DWC2_PHY_TYPE_PARAM_UTMI 1 +#define DWC2_PHY_TYPE_PARAM_ULPI 2 + int phy_utmi_width; int phy_ulpi_ddr; int phy_ulpi_ext_vbus; +#define DWC2_PHY_ULPI_INTERNAL_VBUS 0 +#define DWC2_PHY_ULPI_EXTERNAL_VBUS 1 + int i2c_enable; int ulpi_fs_ls; int host_support_fs_ls_low_power; int host_ls_low_power_phy_clk; +#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ 0 +#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ 1 + int ts_dline; int reload_ctl; int ahbcfg; int uframe_sched; int external_id_pin_ctl; int hibernation; + + /* + * The following parameters are *only* set via device + * properties and cannot be set directly in this structure. + */ + + /* Host parameters */ + bool host_dma; + + /* Gadget parameters */ + bool g_dma; + bool g_dma_desc; + u16 g_rx_fifo_size; + u16 g_np_tx_fifo_size; + u32 g_tx_fifo_size[MAX_EPS_CHANNELS]; }; /** @@ -516,10 +575,9 @@ struct dwc2_hw_params { unsigned op_mode:3; unsigned arch:2; unsigned dma_desc_enable:1; - unsigned dma_desc_fs_enable:1; unsigned enable_dynamic_fifo:1; unsigned en_multiple_tx_fifo:1; - unsigned host_rx_fifo_size:16; + unsigned rx_fifo_size:16; unsigned host_nperio_tx_fifo_size:16; unsigned dev_nperio_tx_fifo_size:16; unsigned host_perio_tx_fifo_size:16; @@ -839,11 +897,13 @@ struct dwc2_hregs_backup { * @ctrl_req: Request for EP0 control packets. * @ep0_state: EP0 control transfers state * @test_mode: USB test mode requested by the host + * @setup_desc_dma: EP0 setup stage desc chain DMA address + * @setup_desc: EP0 setup stage desc chain pointer + * @ctrl_in_desc_dma: EP0 IN data phase desc chain DMA address + * @ctrl_in_desc: EP0 IN data phase desc chain pointer + * @ctrl_out_desc_dma: EP0 OUT data phase desc chain DMA address + * @ctrl_out_desc: EP0 OUT data phase desc chain pointer * @eps: The endpoints being supplied to the gadget framework - * @g_using_dma: Indicate if dma usage is enabled - * @g_rx_fifo_sz: Contains rx fifo size value - * @g_np_g_tx_fifo_sz: Contains Non-Periodic tx fifo size value - * @g_tx_fifo_sz: Contains tx fifo size value per endpoints */ struct dwc2_hsotg { struct device *dev; @@ -851,7 +911,7 @@ struct dwc2_hsotg { /** Params detected from hardware */ struct dwc2_hw_params hw_params; /** Params to actually use */ - struct dwc2_core_params *core_params; + struct dwc2_core_params params; enum usb_otg_state op_state; enum usb_dr_mode dr_mode; unsigned int hcd_enabled:1; @@ -891,6 +951,8 @@ struct dwc2_hsotg { #define DWC2_CORE_REV_2_94a 0x4f54294a #define DWC2_CORE_REV_3_00a 0x4f54300a #define DWC2_CORE_REV_3_10a 0x4f54310a +#define DWC2_FS_IOT_REV_1_00a 0x5531100a +#define DWC2_HS_IOT_REV_1_00a 0x5532100a #if IS_ENABLED(CONFIG_USB_DWC2_HOST) || IS_ENABLED(CONFIG_USB_DWC2_DUAL_ROLE) union dwc2_hcd_internal_flags { @@ -986,15 +1048,18 @@ struct dwc2_hsotg { enum dwc2_ep0_state ep0_state; u8 test_mode; + dma_addr_t setup_desc_dma[2]; + struct dwc2_dma_desc *setup_desc[2]; + dma_addr_t ctrl_in_desc_dma; + struct dwc2_dma_desc *ctrl_in_desc; + dma_addr_t ctrl_out_desc_dma; + struct dwc2_dma_desc *ctrl_out_desc; + struct usb_gadget gadget; unsigned int enabled:1; unsigned int connected:1; struct dwc2_hsotg_ep *eps_in[MAX_EPS_CHANNELS]; struct dwc2_hsotg_ep *eps_out[MAX_EPS_CHANNELS]; - u32 g_using_dma; - u32 g_rx_fifo_sz; - u32 g_np_g_tx_fifo_sz; - u32 g_tx_fifo_sz[MAX_EPS_CHANNELS]; #endif /* CONFIG_USB_DWC2_PERIPHERAL || CONFIG_USB_DWC2_DUAL_ROLE */ }; @@ -1016,6 +1081,22 @@ enum dwc2_halt_status { DWC2_HC_XFER_URB_DEQUEUE, }; +/* Core version information */ +static inline bool dwc2_is_iot(struct dwc2_hsotg *hsotg) +{ + return (hsotg->hw_params.snpsid & 0xfff00000) == 0x55300000; +} + +static inline bool dwc2_is_fs_iot(struct dwc2_hsotg *hsotg) +{ + return (hsotg->hw_params.snpsid & 0xffff0000) == 0x55310000; +} + +static inline bool dwc2_is_hs_iot(struct dwc2_hsotg *hsotg) +{ + return (hsotg->hw_params.snpsid & 0xffff0000) == 0x55320000; +} + /* * The following functions support initialization of the core driver component * and the DWC_otg controller @@ -1025,6 +1106,8 @@ extern int dwc2_core_reset_and_force_dr_mode(struct dwc2_hsotg *hsotg); extern int dwc2_enter_hibernation(struct dwc2_hsotg *hsotg); extern int dwc2_exit_hibernation(struct dwc2_hsotg *hsotg, bool restore); +bool dwc2_force_mode_if_needed(struct dwc2_hsotg *hsotg, bool host); +void dwc2_clear_force_mode(struct dwc2_hsotg *hsotg); void dwc2_force_dr_mode(struct dwc2_hsotg *hsotg); extern bool dwc2_is_controller_alive(struct dwc2_hsotg *hsotg); @@ -1044,217 +1127,16 @@ extern void dwc2_disable_global_interrupts(struct dwc2_hsotg *hcd); /* This function should be called on every hardware interrupt. */ extern irqreturn_t dwc2_handle_common_intr(int irq, void *dev); -/* OTG Core Parameters */ - -/* - * Specifies the OTG capabilities. The driver will automatically - * detect the value for this parameter if none is specified. - * 0 - HNP and SRP capable (default) - * 1 - SRP Only capable - * 2 - No HNP/SRP capable - */ -extern void dwc2_set_param_otg_cap(struct dwc2_hsotg *hsotg, int val); -#define DWC2_CAP_PARAM_HNP_SRP_CAPABLE 0 -#define DWC2_CAP_PARAM_SRP_ONLY_CAPABLE 1 -#define DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE 2 - -/* - * Specifies whether to use slave or DMA mode for accessing the data - * FIFOs. The driver will automatically detect the value for this - * parameter if none is specified. - * 0 - Slave - * 1 - DMA (default, if available) - */ -extern void dwc2_set_param_dma_enable(struct dwc2_hsotg *hsotg, int val); - -/* - * When DMA mode is enabled specifies whether to use - * address DMA or DMA Descritor mode for accessing the data - * FIFOs in device mode. The driver will automatically detect - * the value for this parameter if none is specified. - * 0 - address DMA - * 1 - DMA Descriptor(default, if available) - */ -extern void dwc2_set_param_dma_desc_enable(struct dwc2_hsotg *hsotg, int val); - -/* - * When DMA mode is enabled specifies whether to use - * address DMA or DMA Descritor mode with full speed devices - * for accessing the data FIFOs in host mode. - * 0 - address DMA - * 1 - FS DMA Descriptor(default, if available) - */ -extern void dwc2_set_param_dma_desc_fs_enable(struct dwc2_hsotg *hsotg, - int val); - -/* - * Specifies the maximum speed of operation in host and device mode. - * The actual speed depends on the speed of the attached device and - * the value of phy_type. The actual speed depends on the speed of the - * attached device. - * 0 - High Speed (default) - * 1 - Full Speed - */ -extern void dwc2_set_param_speed(struct dwc2_hsotg *hsotg, int val); -#define DWC2_SPEED_PARAM_HIGH 0 -#define DWC2_SPEED_PARAM_FULL 1 - -/* - * Specifies whether low power mode is supported when attached - * to a Full Speed or Low Speed device in host mode. - * - * 0 - Don't support low power mode (default) - * 1 - Support low power mode - */ -extern void dwc2_set_param_host_support_fs_ls_low_power( - struct dwc2_hsotg *hsotg, int val); - -/* - * Specifies the PHY clock rate in low power mode when connected to a - * Low Speed device in host mode. This parameter is applicable only if - * HOST_SUPPORT_FS_LS_LOW_POWER is enabled. If PHY_TYPE is set to FS - * then defaults to 6 MHZ otherwise 48 MHZ. - * - * 0 - 48 MHz - * 1 - 6 MHz - */ -extern void dwc2_set_param_host_ls_low_power_phy_clk(struct dwc2_hsotg *hsotg, - int val); -#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ 0 -#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ 1 - -/* - * 0 - Use cC FIFO size parameters - * 1 - Allow dynamic FIFO sizing (default) - */ -extern void dwc2_set_param_enable_dynamic_fifo(struct dwc2_hsotg *hsotg, - int val); - -/* - * Number of 4-byte words in the Rx FIFO in host mode when dynamic - * FIFO sizing is enabled. - * 16 to 32768 (default 1024) - */ -extern void dwc2_set_param_host_rx_fifo_size(struct dwc2_hsotg *hsotg, int val); - -/* - * Number of 4-byte words in the non-periodic Tx FIFO in host mode - * when Dynamic FIFO sizing is enabled in the core. - * 16 to 32768 (default 256) - */ -extern void dwc2_set_param_host_nperio_tx_fifo_size(struct dwc2_hsotg *hsotg, - int val); - -/* - * Number of 4-byte words in the host periodic Tx FIFO when dynamic - * FIFO sizing is enabled. - * 16 to 32768 (default 256) - */ -extern void dwc2_set_param_host_perio_tx_fifo_size(struct dwc2_hsotg *hsotg, - int val); - -/* - * The maximum transfer size supported in bytes. - * 2047 to 65,535 (default 65,535) - */ -extern void dwc2_set_param_max_transfer_size(struct dwc2_hsotg *hsotg, int val); - -/* - * The maximum number of packets in a transfer. - * 15 to 511 (default 511) - */ -extern void dwc2_set_param_max_packet_count(struct dwc2_hsotg *hsotg, int val); - -/* - * The number of host channel registers to use. - * 1 to 16 (default 11) - * Note: The FPGA configuration supports a maximum of 11 host channels. - */ -extern void dwc2_set_param_host_channels(struct dwc2_hsotg *hsotg, int val); - -/* - * Specifies the type of PHY interface to use. By default, the driver - * will automatically detect the phy_type. - * - * 0 - Full Speed PHY - * 1 - UTMI+ (default) - * 2 - ULPI - */ -extern void dwc2_set_param_phy_type(struct dwc2_hsotg *hsotg, int val); -#define DWC2_PHY_TYPE_PARAM_FS 0 -#define DWC2_PHY_TYPE_PARAM_UTMI 1 -#define DWC2_PHY_TYPE_PARAM_ULPI 2 - -/* - * Specifies the UTMI+ Data Width. This parameter is - * applicable for a PHY_TYPE of UTMI+ or ULPI. (For a ULPI - * PHY_TYPE, this parameter indicates the data width between - * the MAC and the ULPI Wrapper.) Also, this parameter is - * applicable only if the OTG_HSPHY_WIDTH cC parameter was set - * to "8 and 16 bits", meaning that the core has been - * configured to work at either data path width. - * - * 8 or 16 bits (default 16) - */ -extern void dwc2_set_param_phy_utmi_width(struct dwc2_hsotg *hsotg, int val); - -/* - * Specifies whether the ULPI operates at double or single - * data rate. This parameter is only applicable if PHY_TYPE is - * ULPI. - * - * 0 - single data rate ULPI interface with 8 bit wide data - * bus (default) - * 1 - double data rate ULPI interface with 4 bit wide data - * bus - */ -extern void dwc2_set_param_phy_ulpi_ddr(struct dwc2_hsotg *hsotg, int val); - -/* - * Specifies whether to use the internal or external supply to - * drive the vbus with a ULPI phy. - */ -extern void dwc2_set_param_phy_ulpi_ext_vbus(struct dwc2_hsotg *hsotg, int val); -#define DWC2_PHY_ULPI_INTERNAL_VBUS 0 -#define DWC2_PHY_ULPI_EXTERNAL_VBUS 1 - -/* - * Specifies whether to use the I2Cinterface for full speed PHY. This - * parameter is only applicable if PHY_TYPE is FS. - * 0 - No (default) - * 1 - Yes - */ -extern void dwc2_set_param_i2c_enable(struct dwc2_hsotg *hsotg, int val); - -extern void dwc2_set_param_ulpi_fs_ls(struct dwc2_hsotg *hsotg, int val); - -extern void dwc2_set_param_ts_dline(struct dwc2_hsotg *hsotg, int val); - -/* - * Specifies whether dedicated transmit FIFOs are - * enabled for non periodic IN endpoints in device mode - * 0 - No - * 1 - Yes - */ -extern void dwc2_set_param_en_multiple_tx_fifo(struct dwc2_hsotg *hsotg, - int val); - -extern void dwc2_set_param_reload_ctl(struct dwc2_hsotg *hsotg, int val); - -extern void dwc2_set_param_ahbcfg(struct dwc2_hsotg *hsotg, int val); - -extern void dwc2_set_param_otg_ver(struct dwc2_hsotg *hsotg, int val); - -extern void dwc2_set_parameters(struct dwc2_hsotg *hsotg, - const struct dwc2_core_params *params); - -extern void dwc2_set_all_params(struct dwc2_core_params *params, int value); - -extern int dwc2_get_hwparams(struct dwc2_hsotg *hsotg); +/* The device ID match table */ +extern const struct of_device_id dwc2_of_match_table[]; extern int dwc2_lowlevel_hw_enable(struct dwc2_hsotg *hsotg); extern int dwc2_lowlevel_hw_disable(struct dwc2_hsotg *hsotg); +/* Parameters */ +int dwc2_get_hwparams(struct dwc2_hsotg *hsotg); +int dwc2_init_params(struct dwc2_hsotg *hsotg); + /* * The following functions check the controller's OTG operation mode * capability (GHWCFG2.OTG_MODE). |