diff options
Diffstat (limited to 'drivers/pci/pci.c')
| -rw-r--r-- | drivers/pci/pci.c | 59 |
1 files changed, 42 insertions, 17 deletions
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c index 9afb6114a4cf..60230da957e0 100644 --- a/drivers/pci/pci.c +++ b/drivers/pci/pci.c @@ -65,6 +65,13 @@ struct pci_pme_device { #define PME_TIMEOUT 1000 /* How long between PME checks */ /* + * Following exit from Conventional Reset, devices must be ready within 1 sec + * (PCIe r6.0 sec 6.6.1). A D3cold to D0 transition implies a Conventional + * Reset (PCIe r6.0 sec 5.8). + */ +#define PCI_RESET_WAIT 1000 /* msec */ + +/* * Devices may extend the 1 sec period through Request Retry Status * completions (PCIe r6.0 sec 2.3.1). The spec does not provide an upper * limit, but 60 sec ought to be enough for any device to become @@ -2968,13 +2975,13 @@ static const struct dmi_system_id bridge_d3_blacklist[] = { { /* * Downstream device is not accessible after putting a root port - * into D3cold and back into D0 on Elo i2. + * into D3cold and back into D0 on Elo Continental Z2 board */ - .ident = "Elo i2", + .ident = "Elo Continental Z2", .matches = { - DMI_MATCH(DMI_SYS_VENDOR, "Elo Touch Solutions"), - DMI_MATCH(DMI_PRODUCT_NAME, "Elo i2"), - DMI_MATCH(DMI_PRODUCT_VERSION, "RevB"), + DMI_MATCH(DMI_BOARD_VENDOR, "Elo Touch Solutions"), + DMI_MATCH(DMI_BOARD_NAME, "Geminilake"), + DMI_MATCH(DMI_BOARD_VERSION, "Continental Z2"), }, }, #endif @@ -5102,11 +5109,9 @@ int pci_bridge_wait_for_secondary_bus(struct pci_dev *dev, char *reset_type) * * However, 100 ms is the minimum and the PCIe spec says the * software must allow at least 1s before it can determine that the - * device that did not respond is a broken device. There is - * evidence that 100 ms is not always enough, for example certain - * Titan Ridge xHCI controller does not always respond to - * configuration requests if we only wait for 100 ms (see - * https://bugzilla.kernel.org/show_bug.cgi?id=203885). + * device that did not respond is a broken device. Also device can + * take longer than that to respond if it indicates so through Request + * Retry Status completions. * * Therefore we wait for 100 ms and check for the device presence * until the timeout expires. @@ -5115,16 +5120,36 @@ int pci_bridge_wait_for_secondary_bus(struct pci_dev *dev, char *reset_type) return 0; if (pcie_get_speed_cap(dev) <= PCIE_SPEED_5_0GT) { + u16 status; + pci_dbg(dev, "waiting %d ms for downstream link\n", delay); msleep(delay); - } else { - pci_dbg(dev, "waiting %d ms for downstream link, after activation\n", - delay); - if (!pcie_wait_for_link_delay(dev, true, delay)) { - /* Did not train, no need to wait any further */ - pci_info(dev, "Data Link Layer Link Active not set in 1000 msec\n"); + + if (!pci_dev_wait(child, reset_type, PCI_RESET_WAIT - delay)) + return 0; + + /* + * If the port supports active link reporting we now check + * whether the link is active and if not bail out early with + * the assumption that the device is not present anymore. + */ + if (!dev->link_active_reporting) return -ENOTTY; - } + + pcie_capability_read_word(dev, PCI_EXP_LNKSTA, &status); + if (!(status & PCI_EXP_LNKSTA_DLLLA)) + return -ENOTTY; + + return pci_dev_wait(child, reset_type, + PCIE_RESET_READY_POLL_MS - PCI_RESET_WAIT); + } + + pci_dbg(dev, "waiting %d ms for downstream link, after activation\n", + delay); + if (!pcie_wait_for_link_delay(dev, true, delay)) { + /* Did not train, no need to wait any further */ + pci_info(dev, "Data Link Layer Link Active not set in 1000 msec\n"); + return -ENOTTY; } return pci_dev_wait(child, reset_type, |