diff options
Diffstat (limited to 'arch/arm/boot/dts/imx28-duckbill-2-485.dts')
| -rw-r--r-- | arch/arm/boot/dts/imx28-duckbill-2-485.dts | 174 |
1 files changed, 14 insertions, 160 deletions
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-485.dts b/arch/arm/boot/dts/imx28-duckbill-2-485.dts index d451fa018d83..b73020ff1053 100644 --- a/arch/arm/boot/dts/imx28-duckbill-2-485.dts +++ b/arch/arm/boot/dts/imx28-duckbill-2-485.dts @@ -5,172 +5,13 @@ */ /dts-v1/; -#include <dt-bindings/interrupt-controller/irq.h> -#include <dt-bindings/gpio/gpio.h> -#include "imx28.dtsi" +#include "imx28-duckbill-2.dts" / { model = "I2SE Duckbill 2 485"; compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28"; - memory@40000000 { - device_type = "memory"; - reg = <0x40000000 0x08000000>; - }; - - apb@80000000 { - apbh@80000000 { - ssp0: spi@80010000 { - compatible = "fsl,imx28-mmc"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_8bit_pins_a - &mmc0_cd_cfg &mmc0_sck_cfg>; - bus-width = <8>; - vmmc-supply = <®_3p3v>; - status = "okay"; - non-removable; - }; - - ssp2: spi@80014000 { - compatible = "fsl,imx28-mmc"; - pinctrl-names = "default"; - pinctrl-0 = <&mmc2_4bit_pins_b - &mmc2_cd_cfg &mmc2_sck_cfg_b>; - bus-width = <4>; - vmmc-supply = <®_3p3v>; - status = "okay"; - }; - - pinctrl@80018000 { - pinctrl-names = "default"; - pinctrl-0 = <&hog_pins_a>; - - hog_pins_a: hog@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */ - >; - fsl,drive-strength = <MXS_DRIVE_4mA>; - fsl,voltage = <MXS_VOLTAGE_HIGH>; - fsl,pull-up = <MXS_PULL_DISABLE>; - }; - - mac0_phy_reset_pin: mac0-phy-reset@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_GPMI_ALE__GPIO_0_26 /* PHY Reset */ - >; - fsl,drive-strength = <MXS_DRIVE_4mA>; - fsl,voltage = <MXS_VOLTAGE_HIGH>; - fsl,pull-up = <MXS_PULL_DISABLE>; - }; - - mac0_phy_int_pin: mac0-phy-int@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_GPMI_D07__GPIO_0_7 /* PHY Interrupt */ - >; - fsl,drive-strength = <MXS_DRIVE_4mA>; - fsl,voltage = <MXS_VOLTAGE_HIGH>; - fsl,pull-up = <MXS_PULL_DISABLE>; - }; - - led_pins: leds@0 { - reg = <0>; - fsl,pinmux-ids = < - MX28_PAD_SAIF0_MCLK__GPIO_3_20 - MX28_PAD_SAIF0_LRCLK__GPIO_3_21 - MX28_PAD_I2C0_SCL__GPIO_3_24 - MX28_PAD_I2C0_SDA__GPIO_3_25 - >; - fsl,drive-strength = <MXS_DRIVE_4mA>; - fsl,voltage = <MXS_VOLTAGE_HIGH>; - fsl,pull-up = <MXS_PULL_DISABLE>; - }; - }; - }; - - apbx@80040000 { - lradc@80050000 { - status = "okay"; - }; - - auart0: serial@8006a000 { - pinctrl-names = "default"; - pinctrl-0 = <&auart0_2pins_a>; - status = "okay"; - }; - - duart: serial@80074000 { - pinctrl-names = "default"; - pinctrl-0 = <&duart_pins_a>; - status = "okay"; - }; - - usbphy0: usbphy@8007c000 { - status = "okay"; - }; - }; - }; - - ahb@80080000 { - usb0: usb@80080000 { - status = "okay"; - dr_mode = "peripheral"; - }; - - mac0: ethernet@800f0000 { - phy-mode = "rmii"; - pinctrl-names = "default"; - pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>; - phy-supply = <®_3p3v>; - phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; - phy-reset-duration = <25>; - phy-handle = <ðphy>; - status = "okay"; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - ethphy: ethernet-phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&mac0_phy_int_pin>; - interrupt-parent = <&gpio0>; - interrupts = <7 IRQ_TYPE_EDGE_FALLING>; - max-speed = <100>; - }; - }; - }; - }; - - reg_3p3v: regulator-3p3v { - compatible = "regulator-fixed"; - regulator-name = "3P3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins>; - - status-red { - label = "duckbill:red:status"; - gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "default-on"; - }; - - status-green { - label = "duckbill:green:status"; - gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - }; - rs485-red { label = "duckbill:red:rs485"; gpios = <&gpio3 24 GPIO_ACTIVE_LOW>; @@ -182,3 +23,16 @@ }; }; }; + +&i2c0 { + status = "disabled"; +}; + +&led_pins { + fsl,pinmux-ids = < + MX28_PAD_SAIF0_MCLK__GPIO_3_20 + MX28_PAD_SAIF0_LRCLK__GPIO_3_21 + MX28_PAD_I2C0_SCL__GPIO_3_24 + MX28_PAD_I2C0_SDA__GPIO_3_25 + >; +}; |