1 files changed, 0 insertions, 114 deletions
diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
deleted file mode 100644
index c69f4f065d23..000000000000
--- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+++ /dev/null
@@ -1,114 +0,0 @@
-CFI or JEDEC memory-mapped NOR flash, MTD-RAM (NVRAM...)
-
-Flash chips (Memory Technology Devices) are often used for solid state
-file systems on embedded devices.
-
- - compatible : should contain the specific model of mtd chip(s)
-   used, if known, followed by either "cfi-flash", "jedec-flash",
-   "mtd-ram" or "mtd-rom".
- - reg : Address range(s) of the mtd chip(s)
-   It's possible to (optionally) define multiple "reg" tuples so that
-   non-identical chips can be described in one node.
- - bank-width : Width (in bytes) of the bank.  Equal to the
-   device width times the number of interleaved chips.
- - device-width : (optional) Width of a single mtd chip.  If
-   omitted, assumed to be equal to 'bank-width'.
- - #address-cells, #size-cells : Must be present if the device has
-   sub-nodes representing partitions (see below).  In this case
-   both #address-cells and #size-cells must be equal to 1.
- - no-unaligned-direct-access: boolean to disable the default direct
-   mapping of the flash.
-   On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause
-   problems with JFFS2 usage, as the local bus (LPB) doesn't support
-   unaligned accesses as implemented in the JFFS2 code via memcpy().
-   By defining "no-unaligned-direct-access", the flash will not be
-   exposed directly to the MTD users (e.g. JFFS2) any more.
- - linux,mtd-name: allow to specify the mtd name for retro capability with
-   physmap-flash drivers as boot loader pass the mtd partition via the old
-   device name physmap-flash.
- - use-advanced-sector-protection: boolean to enable support for the
-   advanced sector protection (Spansion: PPB - Persistent Protection
-   Bits) locking.
- - addr-gpios : (optional) List of GPIO descriptors that will be used to
-   address the MSBs address lines. The order goes from LSB to MSB.
-
-For JEDEC compatible devices, the following additional properties
-are defined:
-
- - vendor-id : Contains the flash chip's vendor id (1 byte).
- - device-id : Contains the flash chip's device id (1 byte).
-
-For ROM compatible devices (and ROM fallback from cfi-flash), the following
-additional (optional) property is defined:
-
- - erase-size : The chip's physical erase block size in bytes.
-
- The device tree may optionally contain endianness property.
- little-endian or big-endian : It Represents the endianness that should be used
-                               by the controller to  properly read/write data
-			       from/to the flash. If this property is missing,
-			       the endianness is chosen by the system
-			       (potentially based on extra configuration options).
-
-The device tree may optionally contain sub-nodes describing partitions of the
-address space. See partition.txt for more detail.
-
-Example:
-
-	flash@ff000000 {
-		compatible = "amd,am29lv128ml", "cfi-flash";
-		reg = <ff000000 01000000>;
-		bank-width = <4>;
-		device-width = <1>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		fs@0 {
-			label = "fs";
-			reg = <0 f80000>;
-		};
-		firmware@f80000 {
-			label ="firmware";
-			reg = <f80000 80000>;
-			read-only;
-		};
-	};
-
-Here an example with multiple "reg" tuples:
-
-	flash@f0000000,0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "intel,PC48F4400P0VB", "cfi-flash";
-		reg = <0 0x00000000 0x02000000
-		       0 0x02000000 0x02000000>;
-		bank-width = <2>;
-		partition@0 {
-			label = "test-part1";
-			reg = <0 0x04000000>;
-		};
-	};
-
-An example using SRAM:
-
-	sram@2,0 {
-		compatible = "samsung,k6f1616u6a", "mtd-ram";
-		reg = <2 0 0x00200000>;
-		bank-width = <2>;
-	};
-
-An example using gpio-addrs
-
-	flash@20000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "cfi-flash", "jedec-flash";
-		reg = <0x20000000 0x02000000>;
-		ranges = <0 0x00000000 0x02000000
-		          1 0x02000000 0x02000000>;
-		bank-width = <2>;
-		addr-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-		partition@0 {
-			label = "test-part1";
-			reg = <0 0x04000000>;
-		};
-	};