diff options
| -rw-r--r-- | arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 128 |
1 files changed, 123 insertions, 5 deletions
diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts index bb161b536da4..6a036f9ba1c9 100644 --- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts +++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts @@ -54,6 +54,17 @@ gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>; }; }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <<9611_out>; + }; + }; + }; }; &apps_rsc { @@ -359,12 +370,112 @@ status = "okay"; }; +&gpi_dma1 { + status = "okay"; +}; + &gpu { - /* - * NOTE: "amd,imageon" makes Adreno start in headless mode, remove it - * after display support is added on this board. - */ - compatible = "qcom,adreno-640.1", "qcom,adreno", "amd,imageon"; + status = "okay"; +}; + +&i2c9 { + status = "okay"; + clock-frequency = <400000>; + + lt9611_codec: hdmi-bridge@3b { + compatible = "lontium,lt9611"; + reg = <0x3b>; + #sound-dai-cells = <1>; + + interrupts-extended = <&tlmm 9 IRQ_TYPE_EDGE_FALLING>; + + reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>; + + vdd-supply = <&vreg_s4a_1p8>; + vcc-supply = <&vreg_bob>; + + pinctrl-names = "default"; + pinctrl-0 = <<9611_irq_pin>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lt9611_a: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + + lt9611_b: endpoint { + remote-endpoint = <&mdss_dsi1_out>; + }; + }; + + port@2 { + reg = <2>; + + lt9611_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dsi0 { + status = "okay"; + vdda-supply = <&vreg_l3c_1p2>; + + qcom,dual-dsi-mode; + qcom,master-dsi; + + ports { + port@1 { + endpoint { + remote-endpoint = <<9611_a>; + data-lanes = <0 1 2 3>; + }; + }; + }; +}; + +&mdss_dsi0_phy { + status = "okay"; + vdds-supply = <&vreg_l5a_0p875>; +}; + +&mdss_dsi1 { + vdda-supply = <&vreg_l3c_1p2>; + + qcom,dual-dsi-mode; + + /* DSI1 is slave, so use DSI0 clocks */ + assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>; + + status = "okay"; + + ports { + port@1 { + endpoint { + remote-endpoint = <<9611_b>; + data-lanes = <0 1 2 3>; + }; + }; + }; +}; + +&mdss_dsi1_phy { + vdds-supply = <&vreg_l5a_0p875>; status = "okay"; }; @@ -402,6 +513,13 @@ &tlmm { gpio-reserved-ranges = <0 4>, <126 4>; + + lt9611_irq_pin: lt9611-irq-state { + pins = "gpio9"; + function = "gpio"; + bias-disable; + }; + }; &uart2 { |