diff options
| -rw-r--r-- | drivers/thermal/mediatek/lvts_thermal.c | 57 |
1 files changed, 33 insertions, 24 deletions
diff --git a/drivers/thermal/mediatek/lvts_thermal.c b/drivers/thermal/mediatek/lvts_thermal.c index 4ec09cb8f667..92f4784bb98c 100644 --- a/drivers/thermal/mediatek/lvts_thermal.c +++ b/drivers/thermal/mediatek/lvts_thermal.c @@ -897,24 +897,6 @@ static int lvts_ctrl_configure(struct device *dev, struct lvts_ctrl *lvts_ctrl) writel(value, LVTS_MSRCTL0(lvts_ctrl->base)); /* - * LVTS_MSRCTL1 : Measurement control - * - * Bits: - * - * 9: Ignore MSRCTL0 config and do immediate measurement on sensor3 - * 6: Ignore MSRCTL0 config and do immediate measurement on sensor2 - * 5: Ignore MSRCTL0 config and do immediate measurement on sensor1 - * 4: Ignore MSRCTL0 config and do immediate measurement on sensor0 - * - * That configuration will ignore the filtering and the delays - * introduced below in MONCTL1 and MONCTL2 - */ - if (lvts_ctrl->mode == LVTS_MSR_IMMEDIATE_MODE) { - value = BIT(9) | BIT(6) | BIT(5) | BIT(4); - writel(value, LVTS_MSRCTL1(lvts_ctrl->base)); - } - - /* * LVTS_MONCTL1 : Period unit and group interval configuration * * The clock source of LVTS thermal controller is 26MHz. @@ -979,6 +961,15 @@ static int lvts_ctrl_start(struct device *dev, struct lvts_ctrl *lvts_ctrl) struct thermal_zone_device *tz; u32 sensor_map = 0; int i; + /* + * Bitmaps to enable each sensor on immediate and filtered modes, as + * described in MSRCTL1 and MONCTL0 registers below, respectively. + */ + u32 sensor_imm_bitmap[] = { BIT(4), BIT(5), BIT(6), BIT(9) }; + u32 sensor_filt_bitmap[] = { BIT(0), BIT(1), BIT(2), BIT(3) }; + + u32 *sensor_bitmap = lvts_ctrl->mode == LVTS_MSR_IMMEDIATE_MODE ? + sensor_imm_bitmap : sensor_filt_bitmap; for (i = 0; i < lvts_ctrl->num_lvts_sensor; i++) { @@ -1016,20 +1007,38 @@ static int lvts_ctrl_start(struct device *dev, struct lvts_ctrl *lvts_ctrl) * map, so we can enable the temperature monitoring in * the hardware thermal controller. */ - sensor_map |= BIT(i); + sensor_map |= sensor_bitmap[i]; } /* - * Bits: - * 9: Single point access flow - * 0-3: Enable sensing point 0-3 - * * The initialization of the thermal zones give us * which sensor point to enable. If any thermal zone * was not described in the device tree, it won't be * enabled here in the sensor map. */ - writel(sensor_map | BIT(9), LVTS_MONCTL0(lvts_ctrl->base)); + if (lvts_ctrl->mode == LVTS_MSR_IMMEDIATE_MODE) { + /* + * LVTS_MSRCTL1 : Measurement control + * + * Bits: + * + * 9: Ignore MSRCTL0 config and do immediate measurement on sensor3 + * 6: Ignore MSRCTL0 config and do immediate measurement on sensor2 + * 5: Ignore MSRCTL0 config and do immediate measurement on sensor1 + * 4: Ignore MSRCTL0 config and do immediate measurement on sensor0 + * + * That configuration will ignore the filtering and the delays + * introduced in MONCTL1 and MONCTL2 + */ + writel(sensor_map, LVTS_MSRCTL1(lvts_ctrl->base)); + } else { + /* + * Bits: + * 9: Single point access flow + * 0-3: Enable sensing point 0-3 + */ + writel(sensor_map | BIT(9), LVTS_MONCTL0(lvts_ctrl->base)); + } return 0; } |