net: phy: marvell-88q2xxx: Enable auto negotiation for mv88q2110

The initial marvell-88q2xxx driver only supported the Marvell 88Q2110
PHY without auto negotiation support. The reason documented states that
the provided initialization sequence did not to work. Now a method to
enable auto negotiation have been found by comparing the initialization
of other supported devices and an out-of-tree PHY driver.

Perform the minimal needed initialization of the PHY to get auto
negotiation working and remove the limitation that disables the auto
negotiation feature for the mv88q2110 device.

With this change a 1000Mbps full duplex link is able to be negotiated
between two mv88q2110 and the link works perfectly. The other side also
reflects the manually configure settings of the master device.

    # ethtool eth0
    Settings for eth0:
            Supported ports: [  ]
            Supported link modes:   100baseT1/Full
                                    1000baseT1/Full
            Supported pause frame use: Symmetric Receive-only
            Supports auto-negotiation: Yes
            Supported FEC modes: Not reported
            Advertised link modes:  100baseT1/Full
                                    1000baseT1/Full
            Advertised pause frame use: No
            Advertised auto-negotiation: Yes
            Advertised FEC modes: Not reported
            Link partner advertised link modes:  100baseT1/Full
                                                 1000baseT1/Full
            Link partner advertised pause frame use: No
            Link partner advertised auto-negotiation: Yes
            Link partner advertised FEC modes: Not reported
            Speed: 1000Mb/s
            Duplex: Full
            Auto-negotiation: on
            master-slave cfg: preferred master
            master-slave status: slave
            Port: Twisted Pair
            PHYAD: 0
            Transceiver: external
            MDI-X: Unknown
            Link detected: yes
            SQI: 15/15

Before this change I was not able to manually configure 1000Mbps link,
only a 100Mpps link so this change providers an improvement in
performance for this device.

    [  5] local 10.1.0.2 port 5201 connected to 10.1.0.1 port 38346
    [ ID] Interval           Transfer     Bitrate         Retr  Cwnd
    [  5]   0.00-1.00   sec  96.8 MBytes   812 Mbits/sec    0    469 KBytes
    [  5]   1.00-2.00   sec  94.3 MBytes   791 Mbits/sec    0    469 KBytes
    [  5]   2.00-3.00   sec  96.1 MBytes   806 Mbits/sec    0    469 KBytes
    [  5]   3.00-4.00   sec  98.3 MBytes   825 Mbits/sec    0    469 KBytes
    [  5]   4.00-5.00   sec  98.4 MBytes   825 Mbits/sec    0    469 KBytes
    [  5]   5.00-6.00   sec  98.4 MBytes   826 Mbits/sec    0    469 KBytes
    [  5]   6.00-7.00   sec  98.9 MBytes   830 Mbits/sec    0    469 KBytes
    [  5]   7.00-8.00   sec  91.7 MBytes   769 Mbits/sec    0    469 KBytes
    [  5]   8.00-9.00   sec  99.4 MBytes   834 Mbits/sec    0    747 KBytes
    [  5]   9.00-10.00  sec   101 MBytes   851 Mbits/sec    0    747 KBytes

Signed-off-by: Niklas Söderlund <[email protected]>
Tested-by: Stefan Eichenberger <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>

0 files changed, 0 insertions, 0 deletions