diff options
| author | Marcelo Schmitt <[email protected]> | 2024-07-12 16:20:36 -0300 |
|---|---|---|
| committer | Mark Brown <[email protected]> | 2024-07-29 01:19:51 +0100 |
| commit | f58872f45c36ded048bccc22701b0986019c24d8 (patch) | |
| tree | 1e2057d2e84e9610908c84f55082df11d7a535a6 /include/uapi/linux | |
| parent | 8400291e289ee6b2bf9779ff1c83a291501f017b (diff) | |
spi: Enable controllers to extend the SPI protocol with MOSI idle configuration
The behavior of an SPI controller data output line (SDO or MOSI or COPI
(Controller Output Peripheral Input) for disambiguation) is usually not
specified when the controller is not clocking out data on SCLK edges.
However, there do exist SPI peripherals that require specific MOSI line
state when data is not being clocked out of the controller.
Conventional SPI controllers may set the MOSI line on SCLK edges then bring
it low when no data is going out or leave the line the state of the last
transfer bit. More elaborated controllers are capable to set the MOSI idle
state according to different configurable levels and thus are more suitable
for interfacing with demanding peripherals.
Add SPI mode bits to allow peripherals to request explicit MOSI idle state
when needed.
When supporting a particular MOSI idle configuration, the data output line
state is expected to remain at the configured level when the controller is
not clocking out data. When a device that needs a specific MOSI idle state
is identified, its driver should request the MOSI idle configuration by
setting the proper SPI mode bit.
Acked-by: Nuno Sa <[email protected]>
Reviewed-by: Jonathan Cameron <[email protected]>
Reviewed-by: David Lechner <[email protected]>
Tested-by: David Lechner <[email protected]>
Signed-off-by: Marcelo Schmitt <[email protected]>
Link: https://patch.msgid.link/9802160b5e5baed7f83ee43ac819cb757a19be55.1720810545.git.marcelo.schmitt@analog.com
Signed-off-by: Mark Brown <[email protected]>
Diffstat (limited to 'include/uapi/linux')
| -rw-r--r-- | include/uapi/linux/spi/spi.h | 5 |
1 files changed, 3 insertions, 2 deletions
diff --git a/include/uapi/linux/spi/spi.h b/include/uapi/linux/spi/spi.h index ca56e477d161..ee4ac812b8f8 100644 --- a/include/uapi/linux/spi/spi.h +++ b/include/uapi/linux/spi/spi.h @@ -28,7 +28,8 @@ #define SPI_RX_OCTAL _BITUL(14) /* receive with 8 wires */ #define SPI_3WIRE_HIZ _BITUL(15) /* high impedance turnaround */ #define SPI_RX_CPHA_FLIP _BITUL(16) /* flip CPHA on Rx only xfer */ -#define SPI_MOSI_IDLE_LOW _BITUL(17) /* leave mosi line low when idle */ +#define SPI_MOSI_IDLE_LOW _BITUL(17) /* leave MOSI line low when idle */ +#define SPI_MOSI_IDLE_HIGH _BITUL(18) /* leave MOSI line high when idle */ /* * All the bits defined above should be covered by SPI_MODE_USER_MASK. @@ -38,6 +39,6 @@ * These bits must not overlap. A static assert check should make sure of that. * If adding extra bits, make sure to increase the bit index below as well. */ -#define SPI_MODE_USER_MASK (_BITUL(18) - 1) +#define SPI_MODE_USER_MASK (_BITUL(19) - 1) #endif /* _UAPI_SPI_H */ |