Merge branch 'qca8337-improvements'

Ansuel Smith says:

====================
Multiple improvement for qca8337 switch

This series is the final step of a long process of porting 80+ devices
to use the new qca8k driver instead of the hacky qca one based on never
merged swconfig platform.
Some background to justify all these additions.
QCA used a special binding to declare raw initval to set the swich. I
made a script to convert all these magic values and convert 80+ dts and
scan all the needed "unsupported regs". We find a baseline where we
manage to find the common and used regs so in theory hopefully we don't
have to add anymore things.
We discovered lots of things with this, especially about how differently
qca8327 works compared to qca8337.

In short, we found that qca8327 have some problem with suspend/resume for
their internal phy. It instead sets some dedicated regs that suspend the
phy without setting the standard bit. First 4 patch are to fix this.
There is also a patch about preferring master. This is directly from the
original driver and it seems to be needed to prevent some problem with
the pause frame.

Every ipq806x target sets the mac power sel and this specific reg
regulates the output voltage of the regulator. Without this some
instability can occur.

Some configuration (for some reason) swap mac6 with mac0. We add support
for this.
Also, we discovered that some device doesn't work at all with pll enabled
for sgmii line. In the original code this was based on the switch
revision. In later revision the pll regs were decided based on the switch
type (disabled for qca8327 and enabled for qca8337) but still some
device had that disabled in the initval regs.
Considering we found at least one qca8337 device that required pll
disabled to work (no traffic problem) we decided to introduce a binding
to enable pll and set it only with that.

Lastly, we add support for led open drain that require the power-on-sel
to set. Also, some device have only the power-on-sel set in the initval
so we add also support for that. This is needed for the correct function
of the switch leds.
Qca8327 have a special reg in the pws regs that set it to a reduced
48pin layout. This is needed or the switch doesn't work.

These are all the special configuration we find on all these devices that
are from various targets. Mostly ath79, ipq806x and bcm53xx.
Changes v7:
- Fix missing newline in yaml
- Handle error with wrong cpu port detected
- Move yaml commit as last to fix bot error

Changes v6:
- Convert Documentation to yaml
- Add extra check for cpu port and invalid phy mode
- Add co developed by tag to give credits to Matthew

Changes v5:
- Swap patch. Document first then implement.
- Fix some grammar error reported.
- Rework function. Remove phylink mac_config DT scan and move everything
  to dedicated function in probe.
- Introduce new logic for delay selection where is also supported with
  internal delay declared and rgmii set as phy mode
- Start working on ymal conversion. Will later post this in v6 when we
  finally take final decision about mac swap.

Changes v4:
- Fix typo in SGMII falling edge about using PHY id instead of
  switch id

Changes v3:
- Drop phy patches (proposed separateley)
- Drop special pwr binding. Rework to ipq806x specific
- Better describe compatible and add serial print on switch chip
- Drop mac exchange. Rework falling edge and move it to mac_config
- Add support for port 6 cpu port. Drop hardcoded cpu port to port0
- Improve port stability with sgmii. QCA source have intenal delay also
  for sgmii
- Add warning with pll enabled on wrong configuration

Changes v2:
- Reword Documentation patch to dt-bindings
- Propose first 2 phy patch to net
- Better describe and add hint on how to use all the new
  bindings
- Rework delay scan function and move to phylink mac_config
- Drop package48 wrong binding
- Introduce support for qca8328 switch
- Fix wrong binding name power-on-sel
- Return error on wrong config with led open drain and
  ignore-power-on-sel not set
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 288 insertions, 77 deletions

diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
index a984f06f6f04..bf58d4d1ae9b 100644
--- a/drivers/net/dsa/qca8k.c
+++ b/drivers/net/dsa/qca8k.c
@@ -889,62 +889,183 @@ qca8k_setup_mdio_bus(struct qca8k_priv *priv)
 }
 
 static int
-qca8k_setup_of_rgmii_delay(struct qca8k_priv *priv)
+qca8k_setup_mac_pwr_sel(struct qca8k_priv *priv)
 {
-	struct device_node *port_dn;
-	phy_interface_t mode;
-	struct dsa_port *dp;
-	u32 val;
+	u32 mask = 0;
+	int ret = 0;
 
-	/* CPU port is already checked */
-	dp = dsa_to_port(priv->ds, 0);
+	/* SoC specific settings for ipq8064.
+	 * If more device require this consider adding
+	 * a dedicated binding.
+	 */
+	if (of_machine_is_compatible("qcom,ipq8064"))
+		mask |= QCA8K_MAC_PWR_RGMII0_1_8V;
+
+	/* SoC specific settings for ipq8065 */
+	if (of_machine_is_compatible("qcom,ipq8065"))
+		mask |= QCA8K_MAC_PWR_RGMII1_1_8V;
+
+	if (mask) {
+		ret = qca8k_rmw(priv, QCA8K_REG_MAC_PWR_SEL,
+				QCA8K_MAC_PWR_RGMII0_1_8V |
+				QCA8K_MAC_PWR_RGMII1_1_8V,
+				mask);
+	}
 
-	port_dn = dp->dn;
+	return ret;
+}
+
+static int qca8k_find_cpu_port(struct dsa_switch *ds)
+{
+	struct qca8k_priv *priv = ds->priv;
 
-	/* Check if port 0 is set to the correct type */
-	of_get_phy_mode(port_dn, &mode);
-	if (mode != PHY_INTERFACE_MODE_RGMII_ID &&
-	    mode != PHY_INTERFACE_MODE_RGMII_RXID &&
-	    mode != PHY_INTERFACE_MODE_RGMII_TXID) {
+	/* Find the connected cpu port. Valid port are 0 or 6 */
+	if (dsa_is_cpu_port(ds, 0))
 		return 0;
+
+	dev_dbg(priv->dev, "port 0 is not the CPU port. Checking port 6");
+
+	if (dsa_is_cpu_port(ds, 6))
+		return 6;
+
+	return -EINVAL;
+}
+
+static int
+qca8k_setup_of_pws_reg(struct qca8k_priv *priv)
+{
+	struct device_node *node = priv->dev->of_node;
+	const struct qca8k_match_data *data;
+	u32 val = 0;
+	int ret;
+
+	/* QCA8327 require to set to the correct mode.
+	 * His bigger brother QCA8328 have the 172 pin layout.
+	 * Should be applied by default but we set this just to make sure.
+	 */
+	if (priv->switch_id == QCA8K_ID_QCA8327) {
+		data = of_device_get_match_data(priv->dev);
+
+		/* Set the correct package of 148 pin for QCA8327 */
+		if (data->reduced_package)
+			val |= QCA8327_PWS_PACKAGE148_EN;
+
+		ret = qca8k_rmw(priv, QCA8K_REG_PWS, QCA8327_PWS_PACKAGE148_EN,
+				val);
+		if (ret)
+			return ret;
 	}
 
-	switch (mode) {
-	case PHY_INTERFACE_MODE_RGMII_ID:
-	case PHY_INTERFACE_MODE_RGMII_RXID:
-		if (of_property_read_u32(port_dn, "rx-internal-delay-ps", &val))
-			val = 2;
-		else
-			/* Switch regs accept value in ns, convert ps to ns */
-			val = val / 1000;
+	if (of_property_read_bool(node, "qca,ignore-power-on-sel"))
+		val |= QCA8K_PWS_POWER_ON_SEL;
 
-		if (val > QCA8K_MAX_DELAY) {
-			dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value");
-			val = 3;
+	if (of_property_read_bool(node, "qca,led-open-drain")) {
+		if (!(val & QCA8K_PWS_POWER_ON_SEL)) {
+			dev_err(priv->dev, "qca,led-open-drain require qca,ignore-power-on-sel to be set.");
+			return -EINVAL;
 		}
 
-		priv->rgmii_rx_delay = val;
-		/* Stop here if we need to check only for rx delay */
-		if (mode != PHY_INTERFACE_MODE_RGMII_ID)
-			break;
+		val |= QCA8K_PWS_LED_OPEN_EN_CSR;
+	}
 
-		fallthrough;
-	case PHY_INTERFACE_MODE_RGMII_TXID:
-		if (of_property_read_u32(port_dn, "tx-internal-delay-ps", &val))
-			val = 1;
-		else
-			/* Switch regs accept value in ns, convert ps to ns */
-			val = val / 1000;
+	return qca8k_rmw(priv, QCA8K_REG_PWS,
+			QCA8K_PWS_LED_OPEN_EN_CSR | QCA8K_PWS_POWER_ON_SEL,
+			val);
+}
 
-		if (val > QCA8K_MAX_DELAY) {
-			dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value");
-			val = 3;
-		}
+static int
+qca8k_parse_port_config(struct qca8k_priv *priv)
+{
+	int port, cpu_port_index = 0, ret;
+	struct device_node *port_dn;
+	phy_interface_t mode;
+	struct dsa_port *dp;
+	u32 delay;
 
-		priv->rgmii_tx_delay = val;
-		break;
-	default:
-		return 0;
+	/* We have 2 CPU port. Check them */
+	for (port = 0; port < QCA8K_NUM_PORTS && cpu_port_index < QCA8K_NUM_CPU_PORTS; port++) {
+		/* Skip every other port */
+		if (port != 0 && port != 6)
+			continue;
+
+		dp = dsa_to_port(priv->ds, port);
+		port_dn = dp->dn;
+		cpu_port_index++;
+
+		if (!of_device_is_available(port_dn))
+			continue;
+
+		ret = of_get_phy_mode(port_dn, &mode);
+		if (ret)
+			continue;
+
+		switch (mode) {
+		case PHY_INTERFACE_MODE_RGMII:
+		case PHY_INTERFACE_MODE_RGMII_ID:
+		case PHY_INTERFACE_MODE_RGMII_TXID:
+		case PHY_INTERFACE_MODE_RGMII_RXID:
+		case PHY_INTERFACE_MODE_SGMII:
+			delay = 0;
+
+			if (!of_property_read_u32(port_dn, "tx-internal-delay-ps", &delay))
+				/* Switch regs accept value in ns, convert ps to ns */
+				delay = delay / 1000;
+			else if (mode == PHY_INTERFACE_MODE_RGMII_ID ||
+				 mode == PHY_INTERFACE_MODE_RGMII_TXID)
+				delay = 1;
+
+			if (delay > QCA8K_MAX_DELAY) {
+				dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value");
+				delay = 3;
+			}
+
+			priv->ports_config.rgmii_tx_delay[cpu_port_index] = delay;
+
+			delay = 0;
+
+			if (!of_property_read_u32(port_dn, "rx-internal-delay-ps", &delay))
+				/* Switch regs accept value in ns, convert ps to ns */
+				delay = delay / 1000;
+			else if (mode == PHY_INTERFACE_MODE_RGMII_ID ||
+				 mode == PHY_INTERFACE_MODE_RGMII_RXID)
+				delay = 2;
+
+			if (delay > QCA8K_MAX_DELAY) {
+				dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value");
+				delay = 3;
+			}
+
+			priv->ports_config.rgmii_rx_delay[cpu_port_index] = delay;
+
+			/* Skip sgmii parsing for rgmii* mode */
+			if (mode == PHY_INTERFACE_MODE_RGMII ||
+			    mode == PHY_INTERFACE_MODE_RGMII_ID ||
+			    mode == PHY_INTERFACE_MODE_RGMII_TXID ||
+			    mode == PHY_INTERFACE_MODE_RGMII_RXID)
+				break;
+
+			if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge"))
+				priv->ports_config.sgmii_tx_clk_falling_edge = true;
+
+			if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge"))
+				priv->ports_config.sgmii_rx_clk_falling_edge = true;
+
+			if (of_property_read_bool(port_dn, "qca,sgmii-enable-pll")) {
+				priv->ports_config.sgmii_enable_pll = true;
+
+				if (priv->switch_id == QCA8K_ID_QCA8327) {
+					dev_err(priv->dev, "SGMII PLL should NOT be enabled for qca8327. Aborting enabling");
+					priv->ports_config.sgmii_enable_pll = false;
+				}
+
+				if (priv->switch_revision < 2)
+					dev_warn(priv->dev, "SGMII PLL should NOT be enabled for qca8337 with revision 2 or more.");
+			}
+
+			break;
+		default:
+			continue;
+		}
 	}
 
 	return 0;
@@ -954,15 +1075,20 @@ static int
 qca8k_setup(struct dsa_switch *ds)
 {
 	struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
-	int ret, i;
+	int cpu_port, ret, i;
 	u32 mask;
 
-	/* Make sure that port 0 is the cpu port */
-	if (!dsa_is_cpu_port(ds, 0)) {
-		dev_err(priv->dev, "port 0 is not the CPU port");
-		return -EINVAL;
+	cpu_port = qca8k_find_cpu_port(ds);
+	if (cpu_port < 0) {
+		dev_err(priv->dev, "No cpu port configured in both cpu port0 and port6");
+		return cpu_port;
 	}
 
+	/* Parse CPU port config to be later used in phy_link mac_config */
+	ret = qca8k_parse_port_config(priv);
+	if (ret)
+		return ret;
+
 	mutex_init(&priv->reg_mutex);
 
 	/* Start by setting up the register mapping */
@@ -975,7 +1101,11 @@ qca8k_setup(struct dsa_switch *ds)
 	if (ret)
 		return ret;
 
-	ret = qca8k_setup_of_rgmii_delay(priv);
+	ret = qca8k_setup_of_pws_reg(priv);
+	if (ret)
+		return ret;
+
+	ret = qca8k_setup_mac_pwr_sel(priv);
 	if (ret)
 		return ret;
 
@@ -993,7 +1123,7 @@ qca8k_setup(struct dsa_switch *ds)
 		dev_warn(priv->dev, "mib init failed");
 
 	/* Enable QCA header mode on the cpu port */
-	ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(QCA8K_CPU_PORT),
+	ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(cpu_port),
 			  QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_TX_S |
 			  QCA8K_PORT_HDR_CTRL_ALL << QCA8K_PORT_HDR_CTRL_RX_S);
 	if (ret) {
@@ -1015,10 +1145,10 @@ qca8k_setup(struct dsa_switch *ds)
 
 	/* Forward all unknown frames to CPU port for Linux processing */
 	ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1,
-			  BIT(0) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S |
-			  BIT(0) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S |
-			  BIT(0) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S |
-			  BIT(0) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S);
+			  BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_S |
+			  BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_BC_DP_S |
+			  BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_MC_DP_S |
+			  BIT(cpu_port) << QCA8K_GLOBAL_FW_CTRL1_UC_DP_S);
 	if (ret)
 		return ret;
 
@@ -1026,7 +1156,7 @@ qca8k_setup(struct dsa_switch *ds)
 	for (i = 0; i < QCA8K_NUM_PORTS; i++) {
 		/* CPU port gets connected to all user ports of the switch */
 		if (dsa_is_cpu_port(ds, i)) {
-			ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(QCA8K_CPU_PORT),
+			ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(cpu_port),
 					QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds));
 			if (ret)
 				return ret;
@@ -1038,7 +1168,7 @@ qca8k_setup(struct dsa_switch *ds)
 
 			ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
 					QCA8K_PORT_LOOKUP_MEMBER,
-					BIT(QCA8K_CPU_PORT));
+					BIT(cpu_port));
 			if (ret)
 				return ret;
 
@@ -1137,12 +1267,53 @@ qca8k_setup(struct dsa_switch *ds)
 }
 
 static void
+qca8k_mac_config_setup_internal_delay(struct qca8k_priv *priv, int cpu_port_index,
+				      u32 reg)
+{
+	u32 delay, val = 0;
+	int ret;
+
+	/* Delay can be declared in 3 different way.
+	 * Mode to rgmii and internal-delay standard binding defined
+	 * rgmii-id or rgmii-tx/rx phy mode set.
+	 * The parse logic set a delay different than 0 only when one
+	 * of the 3 different way is used. In all other case delay is
+	 * not enabled. With ID or TX/RXID delay is enabled and set
+	 * to the default and recommended value.
+	 */
+	if (priv->ports_config.rgmii_tx_delay[cpu_port_index]) {
+		delay = priv->ports_config.rgmii_tx_delay[cpu_port_index];
+
+		val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) |
+			QCA8K_PORT_PAD_RGMII_TX_DELAY_EN;
+	}
+
+	if (priv->ports_config.rgmii_rx_delay[cpu_port_index]) {
+		delay = priv->ports_config.rgmii_rx_delay[cpu_port_index];
+
+		val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) |
+			QCA8K_PORT_PAD_RGMII_RX_DELAY_EN;
+	}
+
+	/* Set RGMII delay based on the selected values */
+	ret = qca8k_rmw(priv, reg,
+			QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK |
+			QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK |
+			QCA8K_PORT_PAD_RGMII_TX_DELAY_EN |
+			QCA8K_PORT_PAD_RGMII_RX_DELAY_EN,
+			val);
+	if (ret)
+		dev_err(priv->dev, "Failed to set internal delay for CPU port%d",
+			cpu_port_index == QCA8K_CPU_PORT0 ? 0 : 6);
+}
+
+static void
 qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 			 const struct phylink_link_state *state)
 {
 	struct qca8k_priv *priv = ds->priv;
+	int cpu_port_index, ret;
 	u32 reg, val;
-	int ret;
 
 	switch (port) {
 	case 0: /* 1st CPU port */
@@ -1154,6 +1325,7 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 			return;
 
 		reg = QCA8K_REG_PORT0_PAD_CTRL;
+		cpu_port_index = QCA8K_CPU_PORT0;
 		break;
 	case 1:
 	case 2:
@@ -1172,6 +1344,7 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 			return;
 
 		reg = QCA8K_REG_PORT6_PAD_CTRL;
+		cpu_port_index = QCA8K_CPU_PORT6;
 		break;
 	default:
 		dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
@@ -1186,23 +1359,18 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 
 	switch (state->interface) {
 	case PHY_INTERFACE_MODE_RGMII:
-		/* RGMII mode means no delay so don't enable the delay */
-		qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN);
-		break;
 	case PHY_INTERFACE_MODE_RGMII_ID:
 	case PHY_INTERFACE_MODE_RGMII_TXID:
 	case PHY_INTERFACE_MODE_RGMII_RXID:
-		/* RGMII_ID needs internal delay. This is enabled through
-		 * PORT5_PAD_CTRL for all ports, rather than individual port
-		 * registers
+		qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN);
+
+		/* Configure rgmii delay */
+		qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg);
+
+		/* QCA8337 requires to set rgmii rx delay for all ports.
+		 * This is enabled through PORT5_PAD_CTRL for all ports,
+		 * rather than individual port registers.
 		 */
-		qca8k_write(priv, reg,
-			    QCA8K_PORT_PAD_RGMII_EN |
-			    QCA8K_PORT_PAD_RGMII_TX_DELAY(priv->rgmii_tx_delay) |
-			    QCA8K_PORT_PAD_RGMII_RX_DELAY(priv->rgmii_rx_delay) |
-			    QCA8K_PORT_PAD_RGMII_TX_DELAY_EN |
-			    QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
-		/* QCA8337 requires to set rgmii rx delay */
 		if (priv->switch_id == QCA8K_ID_QCA8337)
 			qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
 				    QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
@@ -1227,8 +1395,11 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 		if (ret)
 			return;
 
-		val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX |
-			QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD;
+		val |= QCA8K_SGMII_EN_SD;
+
+		if (priv->ports_config.sgmii_enable_pll)
+			val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX |
+			       QCA8K_SGMII_EN_TX;
 
 		if (dsa_is_cpu_port(ds, port)) {
 			/* CPU port, we're talking to the CPU MAC, be a PHY */
@@ -1243,6 +1414,35 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 		}
 
 		qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val);
+
+		/* For qca8327/qca8328/qca8334/qca8338 sgmii is unique and
+		 * falling edge is set writing in the PORT0 PAD reg
+		 */
+		if (priv->switch_id == QCA8K_ID_QCA8327 ||
+		    priv->switch_id == QCA8K_ID_QCA8337)
+			reg = QCA8K_REG_PORT0_PAD_CTRL;
+
+		val = 0;
+
+		/* SGMII Clock phase configuration */
+		if (priv->ports_config.sgmii_rx_clk_falling_edge)
+			val |= QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE;
+
+		if (priv->ports_config.sgmii_tx_clk_falling_edge)
+			val |= QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE;
+
+		if (val)
+			ret = qca8k_rmw(priv, reg,
+					QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE |
+					QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE,
+					val);
+
+		/* From original code is reported port instability as SGMII also
+		 * require delay set. Apply advised values here or take them from DT.
+		 */
+		if (state->interface == PHY_INTERFACE_MODE_SGMII)
+			qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg);
+
 		break;
 	default:
 		dev_err(ds->dev, "xMII mode %s not supported for port %d\n",
@@ -1522,9 +1722,12 @@ static int
 qca8k_port_bridge_join(struct dsa_switch *ds, int port, struct net_device *br)
 {
 	struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
-	int port_mask = BIT(QCA8K_CPU_PORT);
+	int port_mask, cpu_port;
 	int i, ret;
 
+	cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
+	port_mask = BIT(cpu_port);
+
 	for (i = 1; i < QCA8K_NUM_PORTS; i++) {
 		if (dsa_to_port(ds, i)->bridge_dev != br)
 			continue;
@@ -1551,7 +1754,9 @@ static void
 qca8k_port_bridge_leave(struct dsa_switch *ds, int port, struct net_device *br)
 {
 	struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
-	int i;
+	int cpu_port, i;
+
+	cpu_port = dsa_to_port(ds, port)->cpu_dp->index;
 
 	for (i = 1; i < QCA8K_NUM_PORTS; i++) {
 		if (dsa_to_port(ds, i)->bridge_dev != br)
@@ -1568,7 +1773,7 @@ qca8k_port_bridge_leave(struct dsa_switch *ds, int port, struct net_device *br)
 	 * this port
 	 */
 	qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
-		  QCA8K_PORT_LOOKUP_MEMBER, BIT(QCA8K_CPU_PORT));
+		  QCA8K_PORT_LOOKUP_MEMBER, BIT(cpu_port));
 }
 
 static int
@@ -1939,7 +2144,12 @@ static int qca8k_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(qca8k_pm_ops,
 			 qca8k_suspend, qca8k_resume);
 
-static const struct qca8k_match_data qca832x = {
+static const struct qca8k_match_data qca8327 = {
+	.id = QCA8K_ID_QCA8327,
+	.reduced_package = true,
+};
+
+static const struct qca8k_match_data qca8328 = {
 	.id = QCA8K_ID_QCA8327,
 };
 
@@ -1948,7 +2158,8 @@ static const struct qca8k_match_data qca833x = {
 };
 
 static const struct of_device_id qca8k_of_match[] = {
-	{ .compatible = "qca,qca8327", .data = &qca832x },
+	{ .compatible = "qca,qca8327", .data = &qca8327 },
+	{ .compatible = "qca,qca8328", .data = &qca8328 },
 	{ .compatible = "qca,qca8334", .data = &qca833x },
 	{ .compatible = "qca,qca8337", .data = &qca833x },
 	{ /* sentinel */ },