dt-bindings: dma: Convert stm32 DMA bindings to json-schema

Convert the STM32 DMA binding to DT schema format using json-schema

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>

1 files changed, 0 insertions, 83 deletions

diff --git a/Documentation/devicetree/bindings/dma/stm32-dma.txt b/Documentation/devicetree/bindings/dma/stm32-dma.txt
deleted file mode 100644
index c5f519097204..000000000000
--- a/Documentation/devicetree/bindings/dma/stm32-dma.txt
+++ /dev/null
@@ -1,83 +0,0 @@
-* STMicroelectronics STM32 DMA controller
-
-The STM32 DMA is a general-purpose direct memory access controller capable of
-supporting 8 independent DMA channels. Each channel can have up to 8 requests.
-
-Required properties:
-- compatible: Should be "st,stm32-dma"
-- reg: Should contain DMA registers location and length. This should include
-  all of the per-channel registers.
-- interrupts: Should contain all of the per-channel DMA interrupts in
-  ascending order with respect to the DMA channel index.
-- clocks: Should contain the input clock of the DMA instance.
-- #dma-cells : Must be <4>. See DMA client paragraph for more details.
-
-Optional properties:
-- dma-requests : Number of DMA requests supported.
-- resets: Reference to a reset controller asserting the DMA controller
-- st,mem2mem: boolean; if defined, it indicates that the controller supports
-  memory-to-memory transfer
-
-Example:
-
-	dma2: dma-controller@40026400 {
-		compatible = "st,stm32-dma";
-		reg = <0x40026400 0x400>;
-		interrupts = <56>,
-			     <57>,
-			     <58>,
-			     <59>,
-			     <60>,
-			     <68>,
-			     <69>,
-			     <70>;
-		clocks = <&clk_hclk>;
-		#dma-cells = <4>;
-		st,mem2mem;
-		resets = <&rcc 150>;
-		dma-requests = <8>;
-	};
-
-* DMA client
-
-DMA clients connected to the STM32 DMA controller must use the format
-described in the dma.txt file, using a four-cell specifier for each
-channel: a phandle to the DMA controller plus the following four integer cells:
-
-1. The channel id
-2. The request line number
-3. A 32bit mask specifying the DMA channel configuration which are device
-   dependent:
-  -bit 9: Peripheral Increment Address
-	0x0: no address increment between transfers
-	0x1: increment address between transfers
- -bit 10: Memory Increment Address
-	0x0: no address increment between transfers
-	0x1: increment address between transfers
- -bit 15: Peripheral Increment Offset Size
-	0x0: offset size is linked to the peripheral bus width
-	0x1: offset size is fixed to 4 (32-bit alignment)
- -bit 16-17: Priority level
-	0x0: low
-	0x1: medium
-	0x2: high
-	0x3: very high
-4. A 32bit bitfield value specifying DMA features which are device dependent:
- -bit 0-1: DMA FIFO threshold selection
-	0x0: 1/4 full FIFO
-	0x1: 1/2 full FIFO
-	0x2: 3/4 full FIFO
-	0x3: full FIFO
-
-
-Example:
-
-	usart1: serial@40011000 {
-		compatible = "st,stm32-uart";
-		reg = <0x40011000 0x400>;
-		interrupts = <37>;
-		clocks = <&clk_pclk2>;
-		dmas = <&dma2 2 4 0x10400 0x3>,
-		       <&dma2 7 5 0x10200 0x3>;
-		dma-names = "rx", "tx";
-	};