diff options
| author | Anand Moon <linux.amoon@gmail.com> | 2024-06-13 18:00:15 +0530 |
|---|---|---|
| committer | Greg Kroah-Hartman <gregkh@linuxfoundation.org> | 2024-06-20 19:39:00 +0200 |
| commit | ccff36934137b426ca988429b5890f83d89f9ed9 (patch) | |
| tree | 77f8528868c57333302280032db216100fc76582 | |
| parent | 3d9894e26e556cd83f1c0ef9f757e375e2cf52c7 (diff) | |
arm64: dts: amlogic: Used onboard usb hub reset on odroid n2
On Odroid n2/n2+ previously use gpio-hog to reset the usb hub,
switch to used on-board usb hub reset to enable the usb hub
and enable power to hub.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240613123020.43500-2-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| -rw-r--r-- | arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi | 36 |
1 files changed, 24 insertions, 12 deletions
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi index d80dd9a3da31..86eb81112232 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi @@ -31,6 +31,30 @@ enable-active-high; }; + /* USB hub supports both USB 2.0 and USB 3.0 root hub */ + usb-hub { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; + + /* 2.0 hub on port 1 */ + hub_2_0: hub@1 { + compatible = "usb5e3,610"; + reg = <1>; + peer-hub = <&hub_3_0>; + vdd-supply = <&usb_pwr_en>; + }; + + /* 3.0 hub on port 4 */ + hub_3_0: hub@2 { + compatible = "usb5e3,620"; + reg = <2>; + peer-hub = <&hub_2_0>; + reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>; + vdd-supply = <&vcc_5v>; + }; + }; + sound { compatible = "amlogic,axg-sound-card"; model = "ODROID-N2"; @@ -234,18 +258,6 @@ "PIN_3", /* GPIOX_17 */ "PIN_5", /* GPIOX_18 */ "PIN_36"; /* GPIOX_19 */ - /* - * WARNING: The USB Hub on the Odroid-N2 needs a reset signal - * to be turned high in order to be detected by the USB Controller - * This signal should be handled by a USB specific power sequence - * in order to reset the Hub when USB bus is powered down. - */ - usb-hub-hog { - gpio-hog; - gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "usb-hub-reset"; - }; }; &i2c3 { |