From 888771a9d04ff7bf96e5ecad37969002c88a95d7 Mon Sep 17 00:00:00 2001 From: Jonathan Marek Date: Mon, 29 Mar 2021 15:00:48 +0300 Subject: arm64: dts: qcom: sm8250: fix display nodes Apply these fixes to the newly added sm8250 display ndoes - Remove "notused" interconnect (which apparently was blindly copied from my old patches) - Use dispcc node example from dt-bindings, removing clocks which aren't documented or used by the driver and fixing the region size. Fixes: 7c1dffd471b1 ("arm64: dts: qcom: sm8250.dtsi: add display system nodes") Signed-off-by: Jonathan Marek [DB: compatibility changes split into separate patch] Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210329120051.3401567-2-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 27 ++++++--------------------- 1 file changed, 6 insertions(+), 21 deletions(-) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 9fe1d39664fe..394973e778f7 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -2287,10 +2287,9 @@ reg = <0 0x0ae00000 0 0x1000>; reg-names = "mdss"; - interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_DISPLAY_CFG>, - <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, + interconnects = <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, <&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>; - interconnect-names = "notused", "mdp0-mem", "mdp1-mem"; + interconnect-names = "mdp0-mem", "mdp1-mem"; power-domains = <&dispcc MDSS_GDSC>; @@ -2540,7 +2539,7 @@ dispcc: clock-controller@af00000 { compatible = "qcom,sm8250-dispcc"; - reg = <0 0x0af00000 0 0x20000>; + reg = <0 0x0af00000 0 0x10000>; mmcx-supply = <&mmcx_reg>; clocks = <&rpmhcc RPMH_CXO_CLK>, <&dsi0_phy 0>, @@ -2548,28 +2547,14 @@ <&dsi1_phy 0>, <&dsi1_phy 1>, <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <&sleep_clk>; + <0>; clock-names = "bi_tcxo", "dsi0_phy_pll_out_byteclk", "dsi0_phy_pll_out_dsiclk", "dsi1_phy_pll_out_byteclk", "dsi1_phy_pll_out_dsiclk", - "dp_link_clk_divsel_ten", - "dp_vco_divided_clk_src_mux", - "dptx1_phy_pll_link_clk", - "dptx1_phy_pll_vco_div_clk", - "dptx2_phy_pll_link_clk", - "dptx2_phy_pll_vco_div_clk", - "edp_phy_pll_link_clk", - "edp_phy_pll_vco_div_clk", - "sleep_clk"; + "dp_phy_pll_link_clk", + "dp_phy_pll_vco_div_clk"; #clock-cells = <1>; #reset-cells = <1>; #power-domain-cells = <1>; -- cgit From 9cf3ebd16eae7957d15e1c08944054fe9035ca8b Mon Sep 17 00:00:00 2001 From: Caleb Connolly Date: Sun, 21 Mar 2021 17:46:21 +0000 Subject: arm64: dts: qcom: sm8150: add other QUP nodes and iommus Add the first and third qupv3 nodes used to hook up peripherals on some devices, as well as the iommus properties for all of them. Signed-off-by: Caleb Connolly Link: https://lore.kernel.org/r/20210321174522.123036-2-caleb@connolly.tech Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8150.dtsi | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index 778613d3410b..01b3f14ff452 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -577,12 +577,26 @@ <&sleep_clk>; }; + qupv3_id_0: geniqup@8c0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x008c0000 0x0 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; + iommus = <&apps_smmu 0xc3 0x0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + }; + qupv3_id_1: geniqup@ac0000 { compatible = "qcom,geni-se-qup"; reg = <0x0 0x00ac0000 0x0 0x6000>; clock-names = "m-ahb", "s-ahb"; clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; + iommus = <&apps_smmu 0x603 0x0>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -598,6 +612,20 @@ }; }; + qupv3_id_2: geniqup@cc0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x00cc0000 0x0 0x6000>; + + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>; + iommus = <&apps_smmu 0x7a3 0x0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + }; + config_noc: interconnect@1500000 { compatible = "qcom,sm8150-config-noc"; reg = <0 0x01500000 0 0x7400>; -- cgit From 81bee6953b581cf35f9a2cd7944dc220630df441 Mon Sep 17 00:00:00 2001 From: Caleb Connolly Date: Sun, 21 Mar 2021 17:46:26 +0000 Subject: arm64: dts: qcom: sm8150: add i2c nodes Tested on the OnePlus 7 Pro (including DMA). Signed-off-by: Caleb Connolly Reviewed-by: Vinod Koul Reviewed-by: Bhupesh Sharma Link: https://lore.kernel.org/r/20210321174522.123036-3-caleb@connolly.tech Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8150.dtsi | 521 +++++++++++++++++++++++++++++++++++ 1 file changed, 521 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index 01b3f14ff452..962882655188 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -588,6 +588,111 @@ #size-cells = <2>; ranges; status = "disabled"; + + i2c0: i2c@880000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00880000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c0_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@884000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00884000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c1_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@888000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00888000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c2_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@88c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x0088c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c3_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c@890000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00890000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c4_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c5: i2c@894000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00894000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c5_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c6: i2c@898000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00898000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c6_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c7: i2c@89c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x0089c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c7_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; qupv3_id_1: geniqup@ac0000 { @@ -602,6 +707,58 @@ ranges; status = "disabled"; + i2c8: i2c@a80000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a80000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c8_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c9: i2c@a84000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a84000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c9_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c10: i2c@a88000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a88000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c10_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c11: i2c@a8c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a8c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c11_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + uart2: serial@a90000 { compatible = "qcom,geni-debug-uart"; reg = <0x0 0x00a90000 0x0 0x4000>; @@ -610,6 +767,32 @@ interrupts = ; status = "disabled"; }; + + i2c12: i2c@a90000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a90000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c12_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c16: i2c@94000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x0094000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c16_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; qupv3_id_2: geniqup@cc0000 { @@ -624,6 +807,84 @@ #size-cells = <2>; ranges; status = "disabled"; + + i2c17: i2c@c80000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c80000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c17_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c18: i2c@c84000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c84000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c18_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c19: i2c@c88000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c88000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c19_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c13: i2c@c8c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c8c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c13_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c14: i2c@c90000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c90000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c14_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c15: i2c@c94000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c94000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c15_default>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; config_noc: interconnect@1500000 { @@ -947,6 +1208,266 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + + qup_i2c0_default: qup-i2c0-default { + mux { + pins = "gpio0", "gpio1"; + function = "qup0"; + }; + + config { + pins = "gpio0", "gpio1"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c1_default: qup-i2c1-default { + mux { + pins = "gpio114", "gpio115"; + function = "qup1"; + }; + + config { + pins = "gpio114", "gpio115"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c2_default: qup-i2c2-default { + mux { + pins = "gpio126", "gpio127"; + function = "qup2"; + }; + + config { + pins = "gpio126", "gpio127"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c3_default: qup-i2c3-default { + mux { + pins = "gpio144", "gpio145"; + function = "qup3"; + }; + + config { + pins = "gpio144", "gpio145"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c4_default: qup-i2c4-default { + mux { + pins = "gpio51", "gpio52"; + function = "qup4"; + }; + + config { + pins = "gpio51", "gpio52"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c5_default: qup-i2c5-default { + mux { + pins = "gpio121", "gpio122"; + function = "qup5"; + }; + + config { + pins = "gpio121", "gpio122"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c6_default: qup-i2c6-default { + mux { + pins = "gpio6", "gpio7"; + function = "qup6"; + }; + + config { + pins = "gpio6", "gpio7"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c7_default: qup-i2c7-default { + mux { + pins = "gpio98", "gpio99"; + function = "qup7"; + }; + + config { + pins = "gpio98", "gpio99"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c8_default: qup-i2c8-default { + mux { + pins = "gpio88", "gpio89"; + function = "qup8"; + }; + + config { + pins = "gpio88", "gpio89"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c9_default: qup-i2c9-default { + mux { + pins = "gpio39", "gpio40"; + function = "qup9"; + }; + + config { + pins = "gpio39", "gpio40"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c10_default: qup-i2c10-default { + mux { + pins = "gpio9", "gpio10"; + function = "qup10"; + }; + + config { + pins = "gpio9", "gpio10"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c11_default: qup-i2c11-default { + mux { + pins = "gpio94", "gpio95"; + function = "qup11"; + }; + + config { + pins = "gpio94", "gpio95"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c12_default: qup-i2c12-default { + mux { + pins = "gpio83", "gpio84"; + function = "qup12"; + }; + + config { + pins = "gpio83", "gpio84"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c13_default: qup-i2c13-default { + mux { + pins = "gpio43", "gpio44"; + function = "qup13"; + }; + + config { + pins = "gpio43", "gpio44"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c14_default: qup-i2c14-default { + mux { + pins = "gpio47", "gpio48"; + function = "qup14"; + }; + + config { + pins = "gpio47", "gpio48"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c15_default: qup-i2c15-default { + mux { + pins = "gpio27", "gpio28"; + function = "qup15"; + }; + + config { + pins = "gpio27", "gpio28"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c16_default: qup-i2c16-default { + mux { + pins = "gpio86", "gpio85"; + function = "qup16"; + }; + + config { + pins = "gpio86", "gpio85"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c17_default: qup-i2c17-default { + mux { + pins = "gpio55", "gpio56"; + function = "qup17"; + }; + + config { + pins = "gpio55", "gpio56"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c18_default: qup-i2c18-default { + mux { + pins = "gpio23", "gpio24"; + function = "qup18"; + }; + + config { + pins = "gpio23", "gpio24"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c19_default: qup-i2c19-default { + mux { + pins = "gpio57", "gpio58"; + function = "qup19"; + }; + + config { + pins = "gpio57", "gpio58"; + drive-strength = <0x02>; + bias-disable; + }; + }; }; remoteproc_mpss: remoteproc@4080000 { -- cgit From 20f9d94e680fb976eb0d7ed253bf791ef3bfc4c9 Mon Sep 17 00:00:00 2001 From: Robert Foss Date: Wed, 24 Mar 2021 13:43:10 +0100 Subject: arm64: dts: qcom: sm8350: Add thermal zones and throttling support sm8350 has 29 thermal sensors split across two tsens controllers. Add the thermal zones to expose them and wireup the cpus to throttle their frequencies on crossing passive temperature thresholds. Signed-off-by: Robert Foss Reviewed-by: Vinod Koul Link: https://lore.kernel.org/r/20210324124308.1265626-2-robert.foss@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8350.dtsi | 826 +++++++++++++++++++++++++++++++++++ 1 file changed, 826 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi index ea285147e43f..513ae00b4740 100644 --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi @@ -10,6 +10,7 @@ #include #include #include +#include / { interrupt-parent = <&intc>; @@ -45,6 +46,7 @@ enable-method = "psci"; next-level-cache = <&L2_0>; qcom,freq-domain = <&cpufreq_hw 0>; + #cooling-cells = <2>; L2_0: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -61,6 +63,7 @@ enable-method = "psci"; next-level-cache = <&L2_100>; qcom,freq-domain = <&cpufreq_hw 0>; + #cooling-cells = <2>; L2_100: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -74,6 +77,7 @@ enable-method = "psci"; next-level-cache = <&L2_200>; qcom,freq-domain = <&cpufreq_hw 0>; + #cooling-cells = <2>; L2_200: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -87,6 +91,7 @@ enable-method = "psci"; next-level-cache = <&L2_300>; qcom,freq-domain = <&cpufreq_hw 0>; + #cooling-cells = <2>; L2_300: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -100,6 +105,7 @@ enable-method = "psci"; next-level-cache = <&L2_400>; qcom,freq-domain = <&cpufreq_hw 1>; + #cooling-cells = <2>; L2_400: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -113,6 +119,7 @@ enable-method = "psci"; next-level-cache = <&L2_500>; qcom,freq-domain = <&cpufreq_hw 1>; + #cooling-cells = <2>; L2_500: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -127,6 +134,7 @@ enable-method = "psci"; next-level-cache = <&L2_600>; qcom,freq-domain = <&cpufreq_hw 1>; + #cooling-cells = <2>; L2_600: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -140,6 +148,7 @@ enable-method = "psci"; next-level-cache = <&L2_700>; qcom,freq-domain = <&cpufreq_hw 2>; + #cooling-cells = <2>; L2_700: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -622,6 +631,28 @@ interrupt-controller; }; + tsens0: thermal-sensor@c222000 { + compatible = "qcom,sm8350-tsens", "qcom,tsens-v2"; + reg = <0 0x0c263000 0 0x1ff>, /* TM */ + <0 0x0c222000 0 0x8>; /* SROT */ + #qcom,sensors = <15>; + interrupts = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 28 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + + tsens1: thermal-sensor@c223000 { + compatible = "qcom,sm8350-tsens", "qcom,tsens-v2"; + reg = <0 0x0c265000 0 0x1ff>, /* TM */ + <0 0x0c223000 0 0x8>; /* SROT */ + #qcom,sensors = <14>; + interrupts = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 29 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + aoss_qmp: power-controller@c300000 { compatible = "qcom,sm8350-aoss-qmp"; reg = <0 0x0c300000 0 0x100000>; @@ -1201,6 +1232,801 @@ }; }; + thermal-zones { + cpu0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 1>; + + trips { + cpu0_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu0_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu0_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu0_alert0>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu0_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 2>; + + trips { + cpu1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu1_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu1_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu1_alert0>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu1_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu2-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 3>; + + trips { + cpu2_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu2_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu2_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu2_alert0>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu2_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu3-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 4>; + + trips { + cpu3_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu3_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu3_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu3_alert0>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu3_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu4-top-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 7>; + + trips { + cpu4_top_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu4_top_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu4_top_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu4_top_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu4_top_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu5-top-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 8>; + + trips { + cpu5_top_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu5_top_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu5_top_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu5_top_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu5_top_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu6-top-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 9>; + + trips { + cpu6_top_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu6_top_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu6_top_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu6_top_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu6_top_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu7-top-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 10>; + + trips { + cpu7_top_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu7_top_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu7_top_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu7_top_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu7_top_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu4-bottom-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 11>; + + trips { + cpu4_bottom_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu4_bottom_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu4_bottom_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu4_bottom_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu4_bottom_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu5-bottom-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 12>; + + trips { + cpu5_bottom_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu5_bottom_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu5_bottom_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu5_bottom_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu5_bottom_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu6-bottom-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 13>; + + trips { + cpu6_bottom_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu6_bottom_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu6_bottom_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu6_bottom_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu6_bottom_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu7-bottom-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 14>; + + trips { + cpu7_bottom_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu7_bottom_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu7_bottom_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu7_bottom_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu7_bottom_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + aoss0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 0>; + + trips { + aoss0_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + cluster0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 5>; + + trips { + cluster0_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + cluster0_crit: cluster0_crit { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cluster1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 6>; + + trips { + cluster1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + cluster1_crit: cluster1_crit { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + aoss1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 0>; + + trips { + aoss1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + gpu-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 1>; + + trips { + gpu1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + gpu-thermal-bottom { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 2>; + + trips { + gpu2_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + nspss1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 3>; + + trips { + nspss1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + nspss2-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 4>; + + trips { + nspss2_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + nspss3-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 5>; + + trips { + nspss3_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + video-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 6>; + + trips { + video_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + mem-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 7>; + + trips { + mem_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + modem1-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 8>; + + trips { + modem1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + modem2-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 9>; + + trips { + modem2_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + modem3-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 10>; + + trips { + modem3_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + modem4-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 11>; + + trips { + modem4_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + camera-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 12>; + + trips { + camera1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + camera-thermal-bottom { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 13>; + + trips { + camera2_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts = , -- cgit From 644e4d972d148628b6094258af913b6b38f4da81 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sat, 3 Apr 2021 02:39:44 +0300 Subject: arm64: dts: qcom: sdm845: add required clocks on the gcc Specify input clocks to the SDM845's Global Clock Controller as required by the bindings. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210402233944.273275-4-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sdm845.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi index 7395ef20b90e..0b2077bce8fa 100644 --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi @@ -1061,6 +1061,16 @@ gcc: clock-controller@100000 { compatible = "qcom,gcc-sdm845"; reg = <0 0x00100000 0 0x1f0000>; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&rpmhcc RPMH_CXO_CLK_A>, + <&sleep_clk>, + <&pcie0_lane>, + <&pcie1_lane>; + clock-names = "bi_tcxo", + "bi_tcxo_ao", + "sleep_clk", + "pcie_0_pipe_clk", + "pcie_1_pipe_clk"; #clock-cells = <1>; #reset-cells = <1>; #power-domain-cells = <1>; @@ -2062,6 +2072,7 @@ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; clock-names = "pipe0"; + #clock-cells = <0>; #phy-cells = <0>; clock-output-names = "pcie_0_pipe_clk"; }; @@ -2170,6 +2181,7 @@ clocks = <&gcc GCC_PCIE_1_PIPE_CLK>; clock-names = "pipe0"; + #clock-cells = <0>; #phy-cells = <0>; clock-output-names = "pcie_1_pipe_clk"; }; -- cgit From 60eb631f5d6eb52fbb5ee257017fb622bc60915f Mon Sep 17 00:00:00 2001 From: satya priya Date: Wed, 31 Mar 2021 17:35:37 +0530 Subject: arm64: dts: qcom: sc7280: Add RPMh regulators for sc7280-idp Add regulator devices for SC7280 as RPMh regulators. This ensures that consumers are able to modify the physical state of PMIC regulators. Reviewed-by: Matthias Kaehlcke Signed-off-by: satya priya Link: https://lore.kernel.org/r/1617192339-3760-4-git-send-email-skakit@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7280-idp.dts | 212 ++++++++++++++++++++++++++++++++ 1 file changed, 212 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts index 950ecb25f281..54d2cb365b71 100644 --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts @@ -22,6 +22,218 @@ }; }; +&apps_rsc { + pm7325-regulators { + compatible = "qcom,pm7325-rpmh-regulators"; + qcom,pmic-id = "b"; + + vreg_s1b_1p8: smps1 { + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7b_0p9: smps7 { + regulator-min-microvolt = <535000>; + regulator-max-microvolt = <1120000>; + }; + + vreg_s8b_1p2: smps8 { + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1500000>; + }; + + vreg_l1b_0p8: ldo1 { + regulator-min-microvolt = <825000>; + regulator-max-microvolt = <925000>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_l6b_1p2: ldo6 { + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1260000>; + }; + + vreg_l7b_2p9: ldo7 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l8b_0p9: ldo8 { + regulator-min-microvolt = <870000>; + regulator-max-microvolt = <970000>; + }; + + vreg_l9b_1p2: ldo9 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1304000>; + }; + + vreg_l11b_1p7: ldo11 { + regulator-min-microvolt = <1504000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l12b_0p8: ldo12 { + regulator-min-microvolt = <751000>; + regulator-max-microvolt = <824000>; + }; + + vreg_l13b_0p8: ldo13 { + regulator-min-microvolt = <530000>; + regulator-max-microvolt = <824000>; + }; + + vreg_l14b_1p2: ldo14 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1304000>; + }; + + vreg_l15b_0p8: ldo15 { + regulator-min-microvolt = <765000>; + regulator-max-microvolt = <1020000>; + }; + + vreg_l16b_1p2: ldo16 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + }; + + vreg_l17b_1p8: ldo17 { + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + }; + + vreg_l18b_1p8: ldo18 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l19b_1p8: ldo19 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + + pm8350c-regulators { + compatible = "qcom,pm8350c-rpmh-regulators"; + qcom,pmic-id = "c"; + + vreg_s1c_2p2: smps1 { + regulator-min-microvolt = <2190000>; + regulator-max-microvolt = <2210000>; + }; + + vreg_s9c_1p0: smps9 { + regulator-min-microvolt = <1010000>; + regulator-max-microvolt = <1170000>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1980000>; + }; + + vreg_l2c_1p8: ldo2 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <1980000>; + }; + + vreg_l3c_3p0: ldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3540000>; + }; + + vreg_l4c_1p8: ldo4 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + }; + + vreg_l5c_1p8: ldo5 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + }; + + vreg_l6c_2p9: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + vreg_l7c_3p0: ldo7 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l9c_2p9: ldo9 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l10c_0p8: ldo10 { + regulator-min-microvolt = <720000>; + regulator-max-microvolt = <1050000>; + }; + + vreg_l11c_2p8: ldo11 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_l12c_1p8: ldo12 { + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l13c_3p0: ldo13 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + }; + }; + + pmr735a-regulators { + compatible = "qcom,pmr735a-rpmh-regulators"; + qcom,pmic-id = "e"; + + vreg_l2e_1p2: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vreg_l3e_0p9: ldo3 { + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1020000>; + }; + + vreg_l4e_1p7: ldo4 { + regulator-min-microvolt = <1776000>; + regulator-max-microvolt = <1890000>; + }; + + vreg_l5e_0p8: ldo5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + + vreg_l6e_0p8: ldo6 { + regulator-min-microvolt = <480000>; + regulator-max-microvolt = <904000>; + }; + }; +}; + &qupv3_id_0 { status = "okay"; }; -- cgit From 24e3eb2e32c688c2c5f6b92bc899b22eea5d5f60 Mon Sep 17 00:00:00 2001 From: Robert Foss Date: Thu, 1 Apr 2021 12:15:36 +0200 Subject: arm64: dts: qcom: sm8350: Add support for PRNG EE RNG (Random Number Generator) in SM8350 features PRNG EE (Execution Environment), hence add devicetree support for it. Reviewed-by: Vinod Koul Signed-off-by: Robert Foss Link: https://lore.kernel.org/r/20210401101536.1014560-1-robert.foss@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8350.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi index 513ae00b4740..5d944588180e 100644 --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi @@ -704,6 +704,13 @@ }; }; + rng: rng@10d3000 { + compatible = "qcom,prng-ee"; + reg = <0 0x010d3000 0 0x1000>; + clocks = <&rpmhcc RPMH_HWKM_CLK>; + clock-names = "core"; + }; + intc: interrupt-controller@17a00000 { compatible = "arm,gic-v3"; #interrupt-cells = <3>; -- cgit From da6b24828d5734128b872dc5319e34d764449098 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Thu, 1 Apr 2021 17:02:52 +0530 Subject: arm64: dts: qcom: sm8350: Add interconnects Add interconnect nodes and add them for modem and cdsp nodes Signed-off-by: Vinod Koul Link: https://lore.kernel.org/r/20210401113252.3078466-1-vkoul@kernel.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8350.dtsi | 78 ++++++++++++++++++++++++++++++++++++ 1 file changed, 78 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi index 5d944588180e..ed0b51bc03ea 100644 --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi @@ -573,6 +573,62 @@ ; }; + config_noc: interconnect@1500000 { + compatible = "qcom,sm8350-config-noc"; + reg = <0 0x01500000 0 0xa580>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + mc_virt: interconnect@1580000 { + compatible = "qcom,sm8350-mc-virt"; + reg = <0 0x01580000 0 0x1000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + system_noc: interconnect@1680000 { + compatible = "qcom,sm8350-system-noc"; + reg = <0 0x01680000 0 0x1c200>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + aggre1_noc: interconnect@16e0000 { + compatible = "qcom,sm8350-aggre1-noc"; + reg = <0 0x016e0000 0 0x1f180>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + aggre2_noc: interconnect@1700000 { + compatible = "qcom,sm8350-aggre2-noc"; + reg = <0 0x01700000 0 0x33000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + mmss_noc: interconnect@1740000 { + compatible = "qcom,sm8350-mmss-noc"; + reg = <0 0x01740000 0 0x1f080>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + lpass_ag_noc: interconnect@3c40000 { + compatible = "qcom,sm8350-lpass-ag-noc"; + reg = <0 0x03c40000 0 0xf080>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + compute_noc: interconnect@a0c0000{ + compatible = "qcom,sm8350-compute-noc"; + reg = <0 0x0a0c0000 0 0xa180>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + tcsr_mutex: hwlock@1f40000 { compatible = "qcom,tcsr-mutex"; reg = <0x0 0x01f40000 0x0 0x40000>; @@ -600,6 +656,8 @@ <&rpmhpd 12>; power-domain-names = "load_state", "cx", "mss"; + interconnects = <&mc_virt 0 &mc_virt 1>; + memory-region = <&pil_modem_mem>; qcom,smem-states = <&smp2p_modem_out 0>; @@ -850,6 +908,10 @@ }; }; }; + + apps_bcm_voter: bcm_voter { + compatible = "qcom,bcm-voter"; + }; }; cpufreq_hw: cpufreq@18591000 { @@ -1001,6 +1063,8 @@ <&rpmhpd 10>; power-domain-names = "load_state", "cx", "mxc"; + interconnects = <&compute_noc 1 &mc_virt 1>; + memory-region = <&pil_cdsp_mem>; qcom,smem-states = <&smp2p_cdsp_out 0>; @@ -1112,6 +1176,20 @@ }; }; + dc_noc: interconnect@90e0000 { + compatible = "qcom,sm8350-dc-noc"; + reg = <0 0x090c0000 0 0x4200>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + gem_noc: interconnect@9100000 { + compatible = "qcom,sm8350-gem-noc"; + reg = <0 0x09100000 0 0xb4000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + usb_1: usb@a6f8800 { compatible = "qcom,sm8350-dwc3", "qcom,dwc3"; reg = <0 0x0a6f8800 0 0x400>; -- cgit From 5b9ec225d4ed222c411c7fbd9b6c781448aa8576 Mon Sep 17 00:00:00 2001 From: "jonathan@marek.ca" Date: Thu, 1 Apr 2021 18:42:55 +0100 Subject: arm64: dts: qcom: sm8250: Add videocc DT node This commit adds the videocc DTS node for sm8250. Signed-off-by: Jonathan Marek Signed-off-by: Bryan O'Donoghue Tested-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210401174256.1810044-2-bryan.odonoghue@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 394973e778f7..3a58b53e0f77 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -17,6 +17,7 @@ #include #include #include +#include / { interrupt-parent = <&intc>; @@ -2282,6 +2283,19 @@ }; }; + videocc: clock-controller@abf0000 { + compatible = "qcom,sm8250-videocc"; + reg = <0 0x0abf0000 0 0x10000>; + clocks = <&gcc GCC_VIDEO_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&rpmhcc RPMH_CXO_CLK_A>; + mmcx-supply = <&mmcx_reg>; + clock-names = "iface", "bi_tcxo", "bi_tcxo_ao"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + mdss: mdss@ae00000 { compatible = "qcom,sdm845-mdss"; reg = <0 0x0ae00000 0 0x1000>; -- cgit From fa245b3f06cd0d3f47799d3fddd1b124806bfa06 Mon Sep 17 00:00:00 2001 From: Bryan O'Donoghue Date: Thu, 1 Apr 2021 18:42:56 +0100 Subject: arm64: dts: qcom: sm8250: Add venus DT node Add DT entries for the sm8250 venus encoder/decoder. Co-developed-by: Jonathan Marek Signed-off-by: Jonathan Marek Co-developed-by: Dikshita Agarwal Signed-off-by: Dikshita Agarwal Signed-off-by: Bryan O'Donoghue Tested-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210401174256.1810044-3-bryan.odonoghue@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 59 ++++++++++++++++++++++++++++++++++++ 1 file changed, 59 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 3a58b53e0f77..edbcdb90614a 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -2283,6 +2283,65 @@ }; }; + venus: video-codec@aa00000 { + compatible = "qcom,sm8250-venus"; + reg = <0 0x0aa00000 0 0x100000>; + interrupts = ; + power-domains = <&videocc MVS0C_GDSC>, + <&videocc MVS0_GDSC>, + <&rpmhpd SM8250_MX>; + power-domain-names = "venus", "vcodec0", "mx"; + operating-points-v2 = <&venus_opp_table>; + + clocks = <&gcc GCC_VIDEO_AXI0_CLK>, + <&videocc VIDEO_CC_MVS0C_CLK>, + <&videocc VIDEO_CC_MVS0_CLK>; + clock-names = "iface", "core", "vcodec0_core"; + + interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_VENUS_CFG>, + <&mmss_noc MASTER_VIDEO_P0 &mc_virt SLAVE_EBI_CH0>; + interconnect-names = "cpu-cfg", "video-mem"; + + iommus = <&apps_smmu 0x2100 0x0400>; + memory-region = <&video_mem>; + + resets = <&gcc GCC_VIDEO_AXI0_CLK_ARES>, + <&videocc VIDEO_CC_MVS0C_CLK_ARES>; + reset-names = "bus", "core"; + + video-decoder { + compatible = "venus-decoder"; + }; + + video-encoder { + compatible = "venus-encoder"; + }; + + venus_opp_table: venus-opp-table { + compatible = "operating-points-v2"; + + opp-720000000 { + opp-hz = /bits/ 64 <720000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-1014000000 { + opp-hz = /bits/ 64 <1014000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-1098000000 { + opp-hz = /bits/ 64 <1098000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-1332000000 { + opp-hz = /bits/ 64 <1332000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + videocc: clock-controller@abf0000 { compatible = "qcom,sm8250-videocc"; reg = <0 0x0abf0000 0 0x10000>; -- cgit From 5aa0d1becd5b3e010302ab1c703fe3357cc44f2e Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Wed, 31 Mar 2021 18:16:13 +0300 Subject: arm64: dts: qcom: sm8250: switch usb1 qmp phy to USB3+DP mode USB1 QMP PHY is not just a USB3 PHY, but USB3+DP PHY. Change device tree nodes accordingly. Signed-off-by: Dmitry Baryshkov Reviewed-by: Bjorn Andersson Link: https://lore.kernel.org/r/20210331151614.3810197-7-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 23 ++++++++++++++++++----- 1 file changed, 18 insertions(+), 5 deletions(-) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index edbcdb90614a..c1b7e28df3d9 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -2058,12 +2058,11 @@ }; usb_1_qmpphy: phy@88e9000 { - compatible = "qcom,sm8250-qmp-usb3-phy"; + compatible = "qcom,sm8250-qmp-usb3-dp-phy"; reg = <0 0x088e9000 0 0x200>, - <0 0x088e8000 0 0x20>; - reg-names = "reg-base", "dp_com"; + <0 0x088e8000 0 0x40>, + <0 0x088ea000 0 0x200>; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -2077,7 +2076,7 @@ <&gcc GCC_USB3_PHY_PRIM_BCR>; reset-names = "phy", "common"; - usb_1_ssphy: lanes@88e9200 { + usb_1_ssphy: usb3-phy@88e9200 { reg = <0 0x088e9200 0 0x200>, <0 0x088e9400 0 0x200>, <0 0x088e9c00 0 0x400>, @@ -2089,6 +2088,20 @@ clock-names = "pipe0"; clock-output-names = "usb3_phy_pipe_clk_src"; }; + + dp_phy: dp-phy@88ea200 { + reg = <0 0x088ea200 0 0x200>, + <0 0x088ea400 0 0x200>, + <0 0x088eac00 0 0x400>, + <0 0x088ea600 0 0x200>, + <0 0x088ea800 0 0x200>, + <0 0x088eaa00 0 0x100>; + #phy-cells = <0>; + #clock-cells = <1>; + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "usb3_phy_pipe_clk_src"; + }; }; usb_2_qmpphy: phy@88eb000 { -- cgit From 9b3153248fbac78fdaaa6e154dadb1f29fcbb81c Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Wed, 31 Mar 2021 18:16:14 +0300 Subject: arm64: dts: qcom: use dp_phy to provide clocks to dispcc Plug dp_phy-provided clocks to display clock controller. Signed-off-by: Dmitry Baryshkov Reviewed-by: Bjorn Andersson Link: https://lore.kernel.org/r/20210331151614.3810197-8-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index c1b7e28df3d9..9aeee4e415c3 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -2632,8 +2632,8 @@ <&dsi0_phy 1>, <&dsi1_phy 0>, <&dsi1_phy 1>, - <0>, - <0>; + <&dp_phy 0>, + <&dp_phy 1>; clock-names = "bi_tcxo", "dsi0_phy_pll_out_byteclk", "dsi0_phy_pll_out_dsiclk", -- cgit From 29bd62ee951b6ee8c0f20f924b80523cf4f179c0 Mon Sep 17 00:00:00 2001 From: Ajit Pandey Date: Sun, 14 Mar 2021 11:40:53 +0530 Subject: arm64: dts: qcom: sc7180-trogdor: Add lpass dai link for I2S driver Add dai link for supporting lpass I2S driver, which is used for audio capture and playback. Add lpass-cpu node with pin controls and i2s primary and secondary dai-links. Tested-by: Douglas Anderson Reviewed-by: Douglas Anderson Reviewed-by: Stephen Boyd Reviewed-by: Srinivas Kandagatla Signed-off-by: Ajit Pandey Signed-off-by: V Sujith Kumar Reddy Signed-off-by: Srinivasa Rao Mandadapu Link: https://lore.kernel.org/r/20210314061054.19451-2-srivasam@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 58 ++++++++++++++++++++++++++++ 1 file changed, 58 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi index 192e2e424fde..5a01aacb81fd 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi @@ -9,6 +9,7 @@ #include #include #include +#include /* PMICs depend on spmi_bus label and so must come after SoC */ #include "pm6150.dtsi" @@ -283,6 +284,42 @@ max-brightness = <1023>; }; }; + + sound: sound { + compatible = "google,sc7180-trogdor"; + model = "sc7180-rt5682-max98357a-1mic"; + + audio-routing = + "Headphone Jack", "HPOL", + "Headphone Jack", "HPOR"; + + #address-cells = <1>; + #size-cells = <0>; + + dai-link@0 { + link-name = "MultiMedia0"; + reg = ; + cpu { + sound-dai = <&lpass_cpu MI2S_PRIMARY>; + }; + + sound_multimedia0_codec: codec { + sound-dai = <&alc5682 0 /* aif1 */>; + }; + }; + + dai-link@1 { + link-name = "MultiMedia1"; + reg = ; + cpu { + sound-dai = <&lpass_cpu MI2S_SECONDARY>; + }; + + sound_multimedia1_codec: codec { + sound-dai = <&max98357a>; + }; + }; + }; }; &qfprom { @@ -720,6 +757,27 @@ hp_i2c: &i2c9 { modem-init; }; +&lpass_cpu { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&sec_mi2s_active>, <&pri_mi2s_active>, <&pri_mi2s_mclk_active>; + + #address-cells = <1>; + #size-cells = <0>; + + mi2s@0 { + reg = ; + qcom,playback-sd-lines = <1>; + qcom,capture-sd-lines = <0>; + }; + + mi2s@1 { + reg = ; + qcom,playback-sd-lines = <0>; + }; +}; + &mdp { status = "okay"; }; -- cgit From f158e7a378f2b375c19cda6a1f35783b7c0615ad Mon Sep 17 00:00:00 2001 From: Srinivasa Rao Mandadapu Date: Sun, 14 Mar 2021 11:40:54 +0530 Subject: arm64: dts: qcom: Add sound node for sc7180-trogdor-coachz This is a trgodor variant, required to have sound node variable for coachz specific platform. Tested-by: Douglas Anderson Signed-off-by: Srinivasa Rao Mandadapu Reviewed-by: Stephen Boyd Reviewed-by: Douglas Anderson Link: https://lore.kernel.org/r/20210314061054.19451-3-srivasam@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi index 4ad520f00485..e2ffe71c2d52 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi @@ -89,6 +89,16 @@ ap_ts_pen_1v8: &i2c4 { data-lanes = <0 1 2 3>; }; +&sound { + compatible = "google,sc7180-coachz"; + model = "sc7180-adau7002-max98357a"; + audio-routing = "PDM_DAT", "DMIC"; +}; + +&sound_multimedia0_codec { + sound-dai = <&adau7002>; +}; + /* PINCTRL - modifications to sc7180-trogdor.dtsi */ &en_pp3300_dx_edp { -- cgit From f66965b06b15a02c0c7da3e5424b029a094a4862 Mon Sep 17 00:00:00 2001 From: Sujit Kautkar Date: Mon, 29 Mar 2021 18:46:10 -0700 Subject: arm64: dts: qcom: Move rmtfs memory region Move rmtfs memory region so that it does not overlap with system RAM (kernel data) when KAsan is enabled. This puts rmtfs right after mba_mem which is not supposed to increase beyond 0x94600000 Reviewed-by: Stephen Boyd Signed-off-by: Sujit Kautkar Link: https://lore.kernel.org/r/20210330014610.1451198-1-sujitka@chromium.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 2 +- arch/arm64/boot/dts/qcom/sc7180.dtsi | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi index 5a01aacb81fd..24d293ef56d7 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi @@ -49,7 +49,7 @@ /* Increase the size from 2MB to 8MB */ &rmtfs_mem { - reg = <0x0 0x84400000 0x0 0x800000>; + reg = <0x0 0x94600000 0x0 0x800000>; }; / { diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi index 83fbb481cae5..a6da78d31fdd 100644 --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi @@ -110,9 +110,9 @@ no-map; }; - rmtfs_mem: memory@84400000 { + rmtfs_mem: memory@94600000 { compatible = "qcom,rmtfs-mem"; - reg = <0x0 0x84400000 0x0 0x200000>; + reg = <0x0 0x94600000 0x0 0x200000>; no-map; qcom,client-id = <1>; -- cgit From 03041cd25d9858649accab60395c613aa97b7d5b Mon Sep 17 00:00:00 2001 From: Jami Kettunen Date: Tue, 6 Apr 2021 04:07:08 +0300 Subject: arm64: dts: qcom: msm8998: Disable MSS remoteproc by default This was already the case for ADSP and SLPI remoteprocs & doesn't affect existing boards where it has been re-enabled. Signed-off-by: Jami Kettunen Link: https://lore.kernel.org/r/20210406010708.2376807-3-jamipkettunen@gmail.com Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi | 4 ++++ arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi | 4 ++++ arch/arm64/boot/dts/qcom/msm8998.dtsi | 2 ++ 3 files changed, 10 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi index b500f24d47bc..125d7923d713 100644 --- a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi @@ -281,6 +281,10 @@ }; }; +&remoteproc_mss { + status = "okay"; +}; + &tlmm { gpio-reserved-ranges = <0 4>, <81 4>; diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi index c1ef0c71d5f5..a1d15eab8553 100644 --- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi @@ -328,6 +328,10 @@ status = "okay"; }; +&remoteproc_mss { + status = "okay"; +}; + &remoteproc_slpi { status = "okay"; }; diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi index 1f2e93aa6553..e9d3ce29937c 100644 --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi @@ -1398,6 +1398,8 @@ <&rpmpd MSM8998_VDDMX>; power-domain-names = "cx", "mx"; + status = "disabled"; + mba { memory-region = <&mba_mem>; }; -- cgit From 47498916afea14cee97d8ff137ad68ea67c15784 Mon Sep 17 00:00:00 2001 From: Jami Kettunen Date: Tue, 6 Apr 2021 04:07:07 +0300 Subject: arm64: dts: qcom: Add support for OnePlus 5/5T Add device trees for OnePlus 5 (cheeseburger) and 5T (dumpling) MSM8998 SoC smartphones with initial support included for: - UFS internal storage - USB peripheral mode - Display - Touch - Bluetooth - Hall effect sensor - Power and volume buttons - Capacitive keypad button backlight (on cheeseburger) Signed-off-by: Jami Kettunen Link: https://lore.kernel.org/r/20210406010708.2376807-2-jamipkettunen@gmail.com Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/Makefile | 2 + .../boot/dts/qcom/msm8998-oneplus-cheeseburger.dts | 42 ++ .../boot/dts/qcom/msm8998-oneplus-common.dtsi | 514 +++++++++++++++++++++ .../boot/dts/qcom/msm8998-oneplus-dumpling.dts | 25 + 4 files changed, 583 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts create mode 100644 arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi create mode 100644 arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 22dadd2ae814..456502aeee49 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -27,6 +27,8 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-asus-novago-tp370ql.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-hp-envy-x2.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-lenovo-miix-630.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-cheeseburger.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts b/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts new file mode 100644 index 000000000000..66b9297588ab --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts @@ -0,0 +1,42 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * OnePlus 5 (cheeseburger) device tree + * + * Copyright (c) 2021, Jami Kettunen + */ + +#include +#include "msm8998-oneplus-common.dtsi" + +/ { + model = "OnePlus 5"; + compatible = "oneplus,cheeseburger", "qcom,msm8998"; + /* Required for bootloader to select correct board */ + qcom,board-id = <8 0 16859 23>; + + /* Capacitive keypad button backlight */ + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&button_backlight_default>; + + button-backlight { + gpios = <&pmi8998_gpio 5 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_KBD_BACKLIGHT; + default-state = "off"; + }; + }; +}; + +&pmi8998_gpio { + button_backlight_default: button-backlight-default { + pinconf { + pins = "gpio5"; + function = "normal"; + bias-pull-down; + qcom,drive-strength = ; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi new file mode 100644 index 000000000000..0f5c7828a901 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi @@ -0,0 +1,514 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * OnePlus 5(T) (cheeseburger / dumpling) common device tree source based on msm8998-mtp.dtsi + * + * Copyright (c) 2021, Jami Kettunen + * Copyright (c) 2016, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include +#include +#include "msm8998.dtsi" +#include "pm8998.dtsi" +#include "pmi8998.dtsi" +#include "pm8005.dtsi" + +/ { + /* Required for bootloader to select correct board */ + qcom,msm-id = <292 0x20001>; /* 8998 v2.1 */ + + chosen { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* Use display framebuffer setup by the UEFI XBL bootloader for simplefb */ + framebuffer0: framebuffer@9d400000 { + compatible = "simple-framebuffer"; + reg = <0x0 0x9d400000 0x0 0x2400000>; + width = <1080>; + height = <1920>; + stride = <(1080 * 4)>; + format = "a8r8g8b8"; + }; + }; + + reserved-memory { + /* Bootloader display framebuffer region */ + cont_splash_mem: memory@9d400000 { + reg = <0x0 0x9d400000 0x0 0x2400000>; + no-map; + }; + + /* For getting crash logs using Android downstream kernels */ + ramoops@ac000000 { + compatible = "ramoops"; + reg = <0x0 0xac000000 0x0 0x200000>; + console-size = <0x80000>; + pmsg-size = <0x40000>; + record-size = <0x8000>; + ftrace-size = <0x20000>; + }; + + /* + * The following memory regions on downstream are "dynamically allocated" + * but given the same addresses every time. Hard code them as these addresses + * are where the OnePlus signed firmware expects them to be. + */ + ipa_fws_region: ipa@f6800000 { + compatible = "shared-dma-pool"; + reg = <0x0 0xf6800000 0x0 0x5000>; + no-map; + }; + zap_shader_region: gpu@f6900000 { + compatible = "shared-dma-pool"; + reg = <0x0 0xf6900000 0x0 0x2000>; + no-map; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + label = "Volume buttons"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&vol_keys_default>; + + vol-down { + label = "Volume down"; + gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <15>; + wakeup-source; + }; + + vol-up { + label = "Volume up"; + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <15>; + wakeup-source; + }; + }; + + gpio-hall-sensor { + compatible = "gpio-keys"; + label = "Hall effect sensor"; + + pinctrl-names = "default"; + pinctrl-0 = <&hall_sensor_default>; + + hall-sensor { + label = "Hall Effect Sensor"; + gpios = <&tlmm 124 GPIO_ACTIVE_LOW>; + linux,input-type = ; + linux,code = ; + linux,can-disable; + wakeup-source; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-always-on; + regulator-boot-on; + }; +}; + +/* + * OnePlus' ADSP firmware requires 30 MiB in total, so increase the adsp_mem + * region by 4 MiB to account for this while relocating the other now + * conflicting memory nodes accordingly. + */ +&adsp_mem { + reg = <0x0 0x8b200000 0x0 0x1e00000>; +}; +&mpss_mem { + reg = <0x0 0x8d000000 0x0 0x7000000>; +}; +&venus_mem { + reg = <0x0 0x94000000 0x0 0x500000>; +}; +&mba_mem { + reg = <0x0 0x94500000 0x0 0x200000>; +}; +&slpi_mem { + reg = <0x0 0x94700000 0x0 0xf00000>; +}; +&ipa_fw_mem { + reg = <0x0 0x95600000 0x0 0x10000>; +}; +&ipa_gsi_mem { + reg = <0x0 0x95610000 0x0 0x5000>; +}; +&gpu_mem { + reg = <0x0 0x95615000 0x0 0x100000>; +}; +&wlan_msa_mem { + reg = <0x0 0x95715000 0x0 0x100000>; +}; + +&blsp1_i2c5 { + status = "okay"; + + touchscreen@20 { + compatible = "syna,rmi4-i2c"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&tlmm>; + interrupts = <125 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_active &ts_reset_active>; + + vdd-supply = <&vreg_l28_3p0>; + vio-supply = <&vreg_l6a_1p8>; + + syna,reset-delay-ms = <20>; + syna,startup-delay-ms = <20>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4_f12: rmi4-f12@12 { + reg = <0x12>; + syna,rezero-wait-ms = <20>; + syna,sensor-type = <1>; + touchscreen-x-mm = <68>; + touchscreen-y-mm = <122>; + }; + }; +}; + +&blsp1_uart3 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; + +&blsp1_uart3_on { + rx { + /delete-property/ bias-disable; + /* + * Configure a pull-up on 46 (RX). This is needed to + * avoid garbage data when the TX pin of the Bluetooth + * module is in tri-state (module powered off or not + * driving the signal yet). + */ + bias-pull-up; + }; + + cts { + /delete-property/ bias-disable; + /* + * Configure a pull-down on 47 (CTS) to match the pull + * of the Bluetooth module. + */ + bias-pull-down; + }; +}; + +&blsp2_uart1 { + status = "okay"; +}; + +&pm8005_lsid1 { + pm8005-regulators { + compatible = "qcom,pm8005-regulators"; + + vdd_s1-supply = <&vph_pwr>; + + pm8005_s1: s1 { /* VDD_GFX supply */ + regulator-min-microvolt = <524000>; + regulator-max-microvolt = <1100000>; + regulator-enable-ramp-delay = <500>; + + /* hack until we rig up the gpu consumer */ + regulator-always-on; + }; + }; +}; + +&pm8998_gpio { + vol_keys_default: vol-keys-default { + pinconf { + pins = "gpio5", "gpio6"; + function = "normal"; + bias-pull-up; + input-enable; + qcom,drive-strength = ; + }; + }; +}; + +&qusb2phy { + status = "okay"; + + vdda-pll-supply = <&vreg_l12a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; +}; + +&rpm_requests { + pm8998-regulators { + compatible = "qcom,rpm-pm8998-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_s13-supply = <&vph_pwr>; + vdd_l1_l27-supply = <&vreg_s7a_1p025>; + vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; + vdd_l3_l11-supply = <&vreg_s7a_1p025>; + vdd_l4_l5-supply = <&vreg_s7a_1p025>; + vdd_l6-supply = <&vreg_s5a_2p04>; + vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; + vdd_l9-supply = <&vreg_bob>; + vdd_l10_l23_l25-supply = <&vreg_bob>; + vdd_l13_l19_l21-supply = <&vreg_bob>; + vdd_l16_l28-supply = <&vreg_bob>; + vdd_l18_l22-supply = <&vreg_bob>; + vdd_l20_l24-supply = <&vreg_bob>; + vdd_l26-supply = <&vreg_s3a_1p35>; + vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; + + vreg_s3a_1p35: s3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + vreg_s4a_1p8: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + }; + vreg_s5a_2p04: s5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + vreg_s7a_1p025: s7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + vreg_l1a_0p875: l1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + }; + vreg_l2a_1p2: l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + vreg_l3a_1p0: l3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + vreg_l5a_0p8: l5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + vreg_l6a_1p8: l6 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <1808000>; + }; + vreg_l7a_1p8: l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l8a_1p2: l8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + vreg_l9a_1p8: l9 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + vreg_l10a_1p8: l10 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + vreg_l11a_1p0: l11 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + vreg_l12a_1p8: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l13a_2p95: l13 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + vreg_l14a_1p88: l14 { + regulator-min-microvolt = <1880000>; + regulator-max-microvolt = <1880000>; + }; + vreg_l15a_1p8: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l16a_2p7: l16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + }; + vreg_l17a_1p3: l17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + }; + vreg_l18a_2p7: l18 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + }; + vreg_l19a_3p0: l19 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + }; + vreg_l20a_2p95: l20 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-allow-set-load; + }; + vreg_l21a_2p95: l21 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-allow-set-load; + regulator-system-load = <800000>; + }; + vreg_l22a_2p85: l22 { + regulator-min-microvolt = <2864000>; + regulator-max-microvolt = <2864000>; + }; + vreg_l23a_3p3: l23 { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3312000>; + }; + vreg_l24a_3p075: l24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + }; + vreg_l25a_3p3: l25 { + regulator-min-microvolt = <3104000>; + regulator-max-microvolt = <3312000>; + }; + vreg_l26a_1p2: l26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-allow-set-load; + }; + vreg_l28_3p0: l28 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + }; + vreg_lvs1a_1p8: lvs1 { }; + vreg_lvs2a_1p8: lvs2 { }; + }; + + pmi8998-regulators { + compatible = "qcom,rpm-pmi8998-regulators"; + + vdd_bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3600000>; + }; + }; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + hall_sensor_default: hall-sensor-default { + pins = "gpio124"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + + ts_int_active: ts-int-active { + pins = "gpio125"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + ts_reset_active: ts-reset-active { + pins = "gpio89"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; +}; + +&ufshc { + status = "okay"; + + vcc-supply = <&vreg_l20a_2p95>; + vccq-supply = <&vreg_l26a_1p2>; + vccq2-supply = <&vreg_s4a_1p8>; + vcc-max-microamp = <750000>; + vccq-max-microamp = <560000>; + vccq2-max-microamp = <750000>; +}; + +&ufsphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l2a_1p2>; + vddp-ref-clk-supply = <&vreg_l26a_1p2>; + vdda-phy-max-microamp = <51400>; + vdda-pll-max-microamp = <14600>; + vddp-ref-clk-max-microamp = <100>; + vddp-ref-clk-always-on; +}; + +&usb3 { + status = "okay"; + + /* Disable USB3 clock requirement as the device only supports USB2 */ + qcom,select-utmi-as-pipe-clk; +}; + +&usb3_dwc3 { + /* Drop the unused USB 3 PHY */ + phys = <&qusb2phy>; + phy-names = "usb2-phy"; + + /* Fastest mode for USB 2 */ + maximum-speed = "high-speed"; + + /* Force to peripheral until we can switch modes */ + dr_mode = "peripheral"; +}; + +&wifi { + /* Leave disabled until MSS is functional */ + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts b/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts new file mode 100644 index 000000000000..544b9b0ae44b --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * OnePlus 5T (dumpling) device tree + * + * Copyright (c) 2021, Jami Kettunen + */ + +#include "msm8998-oneplus-common.dtsi" + +/ { + model = "OnePlus 5T"; + compatible = "oneplus,dumpling", "qcom,msm8998"; + /* Required for bootloader to select correct board */ + qcom,board-id = <8 0 17801 43>; +}; + +/* Update the screen height values from 1920 to 2160 on the 5T */ +&framebuffer0 { + height = <2160>; +}; + +/* Adjust digitizer area height to match the 5T's taller panel */ +&rmi4_f12 { + touchscreen-y-mm = <137>; +}; -- cgit From 0392968dbe099d343c676ea8fd1e878f1fd4682a Mon Sep 17 00:00:00 2001 From: Sai Prakash Ranjan Date: Tue, 16 Mar 2021 00:05:46 +0530 Subject: arm64: dts: qcom: sc7280: Add device tree node for LLCC Add a DT node for Last level cache (aka. system cache) controller which provides control over the last level cache present on SC7280 SoC. Signed-off-by: Sai Prakash Ranjan Reviewed-by: Stephen Boyd Link: https://lore.kernel.org/r/5bacaa8350e0d9553dccd623a15513590e795b47.1615832893.git.saiprakash.ranjan@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7280.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index 39cf0bee1eb0..3cc4c3e48b9b 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -305,6 +305,13 @@ }; }; + system-cache-controller@9200000 { + compatible = "qcom,sc7280-llcc"; + reg = <0 0x09200000 0 0xd0000>, <0 0x09600000 0 0x50000>; + reg-names = "llcc_base", "llcc_broadcast_base"; + interrupts = ; + }; + pdc: interrupt-controller@b220000 { compatible = "qcom,sc7280-pdc", "qcom,pdc"; reg = <0 0x0b220000 0 0x30000>; -- cgit From 2257fac94bc24d502fca8487517d4cf617f7041b Mon Sep 17 00:00:00 2001 From: Sai Prakash Ranjan Date: Tue, 16 Mar 2021 00:05:47 +0530 Subject: arm64: dts: qcom: sc7280: Add IPCC for SC7280 SoC Add the IPCC DT node which is used to send and receive IPC signals with remoteprocs for SC7280 SoC. Cc: Manivannan Sadhasivam Cc: Jassi Brar Signed-off-by: Sai Prakash Ranjan Reviewed-by: Manivannan Sadhasivam Reviewed-by: Stephen Boyd Link: https://lore.kernel.org/r/8374f407386209d2e7891763de3fa2450a14ad60.1615832893.git.saiprakash.ranjan@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7280.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index 3cc4c3e48b9b..6c6fa4fa1b0f 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -8,6 +8,7 @@ #include #include #include +#include #include #include @@ -282,6 +283,15 @@ #power-domain-cells = <1>; }; + ipcc: mailbox@408000 { + compatible = "qcom,sc7280-ipcc", "qcom,ipcc"; + reg = <0 0x00408000 0 0x1000>; + interrupts = ; + interrupt-controller; + #interrupt-cells = <3>; + #mbox-cells = <2>; + }; + qupv3_id_0: geniqup@9c0000 { compatible = "qcom,geni-se-qup"; reg = <0 0x009c0000 0 0x2000>; -- cgit From 208979a8f9cb8ea2a453f043b4a91cf753a98e37 Mon Sep 17 00:00:00 2001 From: Sai Prakash Ranjan Date: Tue, 16 Mar 2021 00:05:48 +0530 Subject: arm64: dts: qcom: sc7280: Add AOSS QMP node Add a DT node for the AOSS QMP on SC7280 SoC. Signed-off-by: Sai Prakash Ranjan Link: https://lore.kernel.org/r/12f013a09989dbc3075bfb204653dc02d54ae8a1.1615832893.git.saiprakash.ranjan@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7280.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index 6c6fa4fa1b0f..ae3d2b31364a 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -9,6 +9,7 @@ #include #include #include +#include #include #include @@ -335,6 +336,19 @@ interrupt-controller; }; + aoss_qmp: power-controller@c300000 { + compatible = "qcom,sc7280-aoss-qmp"; + reg = <0 0x0c300000 0 0x100000>; + interrupts-extended = <&ipcc IPCC_CLIENT_AOP + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_AOP + IPCC_MPROC_SIGNAL_GLINK_QMP>; + + #clock-cells = <0>; + #power-domain-cells = <1>; + }; + spmi_bus: spmi@c440000 { compatible = "qcom,spmi-pmic-arb"; reg = <0 0x0c440000 0 0x1100>, -- cgit From 544cebe1895638a95ec0cd9e046e707a622592df Mon Sep 17 00:00:00 2001 From: Sai Prakash Ranjan Date: Tue, 16 Mar 2021 00:05:49 +0530 Subject: arm64: dts: qcom: sc7280: Add Coresight support Add coresight components found on SC7280 SoC. Cc: Mathieu Poirier Cc: Suzuki K Poulose Cc: Mike Leach Cc: Leo Yan Signed-off-by: Sai Prakash Ranjan Link: https://lore.kernel.org/r/de07324628f88900b72357f4ef7f0c7db7e3409d.1615832893.git.saiprakash.ranjan@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7280.dtsi | 489 +++++++++++++++++++++++++++++++++++ 1 file changed, 489 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index ae3d2b31364a..2cc478553935 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -316,6 +316,495 @@ }; }; + stm@6002000 { + compatible = "arm,coresight-stm", "arm,primecell"; + reg = <0 0x06002000 0 0x1000>, + <0 0x16280000 0 0x180000>; + reg-names = "stm-base", "stm-stimulus-base"; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + stm_out: endpoint { + remote-endpoint = <&funnel0_in7>; + }; + }; + }; + }; + + funnel@6041000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06041000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + funnel0_out: endpoint { + remote-endpoint = <&merge_funnel_in0>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@7 { + reg = <7>; + funnel0_in7: endpoint { + remote-endpoint = <&stm_out>; + }; + }; + }; + }; + + funnel@6042000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06042000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + funnel1_out: endpoint { + remote-endpoint = <&merge_funnel_in1>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@4 { + reg = <4>; + funnel1_in4: endpoint { + remote-endpoint = <&apss_merge_funnel_out>; + }; + }; + }; + }; + + funnel@6045000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06045000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + merge_funnel_out: endpoint { + remote-endpoint = <&swao_funnel_in>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + merge_funnel_in0: endpoint { + remote-endpoint = <&funnel0_out>; + }; + }; + + port@1 { + reg = <1>; + merge_funnel_in1: endpoint { + remote-endpoint = <&funnel1_out>; + }; + }; + }; + }; + + replicator@6046000 { + compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; + reg = <0 0x06046000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + replicator_out: endpoint { + remote-endpoint = <&etr_in>; + }; + }; + }; + + in-ports { + port { + replicator_in: endpoint { + remote-endpoint = <&swao_replicator_out>; + }; + }; + }; + }; + + etr@6048000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x06048000 0 0x1000>; + iommus = <&apps_smmu 0x04c0 0>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,scatter-gather; + + in-ports { + port { + etr_in: endpoint { + remote-endpoint = <&replicator_out>; + }; + }; + }; + }; + + funnel@6b04000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06b04000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + swao_funnel_out: endpoint { + remote-endpoint = <&etf_in>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@7 { + reg = <7>; + swao_funnel_in: endpoint { + remote-endpoint = <&merge_funnel_out>; + }; + }; + }; + }; + + etf@6b05000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x06b05000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + etf_out: endpoint { + remote-endpoint = <&swao_replicator_in>; + }; + }; + }; + + in-ports { + port { + etf_in: endpoint { + remote-endpoint = <&swao_funnel_out>; + }; + }; + }; + }; + + replicator@6b06000 { + compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; + reg = <0 0x06b06000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + qcom,replicator-loses-context; + + out-ports { + port { + swao_replicator_out: endpoint { + remote-endpoint = <&replicator_in>; + }; + }; + }; + + in-ports { + port { + swao_replicator_in: endpoint { + remote-endpoint = <&etf_out>; + }; + }; + }; + }; + + etm@7040000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07040000 0 0x1000>; + + cpu = <&CPU0>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm0_out: endpoint { + remote-endpoint = <&apss_funnel_in0>; + }; + }; + }; + }; + + etm@7140000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07140000 0 0x1000>; + + cpu = <&CPU1>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm1_out: endpoint { + remote-endpoint = <&apss_funnel_in1>; + }; + }; + }; + }; + + etm@7240000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07240000 0 0x1000>; + + cpu = <&CPU2>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm2_out: endpoint { + remote-endpoint = <&apss_funnel_in2>; + }; + }; + }; + }; + + etm@7340000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07340000 0 0x1000>; + + cpu = <&CPU3>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm3_out: endpoint { + remote-endpoint = <&apss_funnel_in3>; + }; + }; + }; + }; + + etm@7440000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07440000 0 0x1000>; + + cpu = <&CPU4>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm4_out: endpoint { + remote-endpoint = <&apss_funnel_in4>; + }; + }; + }; + }; + + etm@7540000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07540000 0 0x1000>; + + cpu = <&CPU5>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm5_out: endpoint { + remote-endpoint = <&apss_funnel_in5>; + }; + }; + }; + }; + + etm@7640000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07640000 0 0x1000>; + + cpu = <&CPU6>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm6_out: endpoint { + remote-endpoint = <&apss_funnel_in6>; + }; + }; + }; + }; + + etm@7740000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07740000 0 0x1000>; + + cpu = <&CPU7>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm7_out: endpoint { + remote-endpoint = <&apss_funnel_in7>; + }; + }; + }; + }; + + funnel@7800000 { /* APSS Funnel */ + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x07800000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + apss_funnel_out: endpoint { + remote-endpoint = <&apss_merge_funnel_in>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + apss_funnel_in0: endpoint { + remote-endpoint = <&etm0_out>; + }; + }; + + port@1 { + reg = <1>; + apss_funnel_in1: endpoint { + remote-endpoint = <&etm1_out>; + }; + }; + + port@2 { + reg = <2>; + apss_funnel_in2: endpoint { + remote-endpoint = <&etm2_out>; + }; + }; + + port@3 { + reg = <3>; + apss_funnel_in3: endpoint { + remote-endpoint = <&etm3_out>; + }; + }; + + port@4 { + reg = <4>; + apss_funnel_in4: endpoint { + remote-endpoint = <&etm4_out>; + }; + }; + + port@5 { + reg = <5>; + apss_funnel_in5: endpoint { + remote-endpoint = <&etm5_out>; + }; + }; + + port@6 { + reg = <6>; + apss_funnel_in6: endpoint { + remote-endpoint = <&etm6_out>; + }; + }; + + port@7 { + reg = <7>; + apss_funnel_in7: endpoint { + remote-endpoint = <&etm7_out>; + }; + }; + }; + }; + + funnel@7810000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x07810000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + apss_merge_funnel_out: endpoint { + remote-endpoint = <&funnel1_in4>; + }; + }; + }; + + in-ports { + port { + apss_merge_funnel_in: endpoint { + remote-endpoint = <&apss_funnel_out>; + }; + }; + }; + }; + system-cache-controller@9200000 { compatible = "qcom,sc7280-llcc"; reg = <0 0x09200000 0 0xd0000>, <0 0x09600000 0 0x50000>; -- cgit From 0e5a6f27036e93110d3710d489fcc1408a674e62 Mon Sep 17 00:00:00 2001 From: Sumit Semwal Date: Mon, 5 Apr 2021 01:14:37 +0530 Subject: arm64: dts: qcom: sdm845-xiaomi-beryllium: Add DSI and panel bits Enabling the Display panel for beryllium requires DSI labibb regulators and panel dts nodes to be added. It is also required to keep some of the regulators as always-on. Signed-off-by: Sumit Semwal Signed-off-by: Amit Pundir Reviewed-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210404194437.537011-1-amit.pundir@linaro.org Signed-off-by: Bjorn Andersson --- .../boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 71 ++++++++++++++++++++++ 1 file changed, 71 insertions(+) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts index 86cbae63eaf7..7d029425336e 100644 --- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts @@ -157,6 +157,14 @@ regulator-initial-mode = ; }; + vreg_l14a_1p8: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + regulator-boot-on; + regulator-always-on; + }; + vreg_l17a_1p3: ldo17 { regulator-min-microvolt = <1304000>; regulator-max-microvolt = <1304000>; @@ -191,6 +199,7 @@ regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-initial-mode = ; + regulator-boot-on; }; }; }; @@ -200,6 +209,43 @@ firmware-name = "qcom/sdm845/cdsp.mdt"; }; +&dsi0 { + status = "okay"; + vdda-supply = <&vreg_l26a_1p2>; + + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "tianma,fhd-video"; + reg = <0>; + vddi0-supply = <&vreg_l14a_1p8>; + vddpos-supply = <&lab>; + vddneg-supply = <&ibb>; + + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; + + port { + tianma_nt36672a_in_0: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; +}; + +&dsi0_out { + remote-endpoint = <&tianma_nt36672a_in_0>; + data-lanes = <0 1 2 3>; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vreg_l1a_0p875>; +}; + &gcc { protected-clocks = , , @@ -215,6 +261,31 @@ }; }; +&ibb { + regulator-min-microvolt = <4600000>; + regulator-max-microvolt = <6000000>; + regulator-over-current-protection; + regulator-pull-down; + regulator-soft-start; + qcom,discharge-resistor-kohms = <300>; +}; + +&lab { + regulator-min-microvolt = <4600000>; + regulator-max-microvolt = <6000000>; + regulator-over-current-protection; + regulator-pull-down; + regulator-soft-start; +}; + +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + &mss_pil { status = "okay"; firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt"; -- cgit From 7443ff06da45aa68d63dd8c9c173470ba971c56a Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 18 Mar 2021 23:14:05 +0300 Subject: arm64: dts: sdm845-db845c: make firmware filenames follow linux-firmware Cange aDSP and cDSP firmware filenames to follow filenames merged into linux-firmware tree. Switch from split .mdt files to merged .mbn files. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210318201405.2244723-1-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts index 6242475dd720..2d5533dd4ec2 100644 --- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts @@ -244,7 +244,7 @@ &adsp_pas { status = "okay"; - firmware-name = "qcom/sdm845/adsp.mdt"; + firmware-name = "qcom/sdm845/adsp.mbn"; }; &apps_rsc { @@ -390,7 +390,7 @@ &cdsp_pas { status = "okay"; - firmware-name = "qcom/sdm845/cdsp.mdt"; + firmware-name = "qcom/sdm845/cdsp.mbn"; }; &dsi0 { -- cgit From 8385119b3295fa87c43a80faed5644bbdab02b8c Mon Sep 17 00:00:00 2001 From: Stephan Gerhold Date: Wed, 7 Apr 2021 18:36:48 +0200 Subject: arm64: dts: qcom: msm8916: Add GICv2 hypervisor registers/interrupt The ARM Cortex-A53 CPU cores and QGIC2 interrupt controller (an implementation of the ARM GIC 2.0 specification) used in MSM8916 support virtualization, e.g. for KVM on Linux. However, so far it was not possible to make use of this functionality, because Qualcomm's proprietary "hyp" firmware blocks the EL2 mode of the CPU and only allows booting Linux in EL1. However, on devices without (firmware) secure boot there is no need to rely on all of Qualcomm's firmware. The "hyp" firmware on MSM8916 seems simple enough that it can be replaced with an open-source alternative created only based on trial and error - with some similar EL2/EL1 initialization code adapted from Linux and U-Boot. qhypstub [1] is such an open-source firmware for MSM8916 that can be used as drop-in replacement for Qualcomm's "hyp" firmware. It does not implement any hypervisor functionality. Instead, it allows booting Linux/KVM (or other hypervisors) in EL2. With Linux booting in EL2, KVM seems to be working just fine on MSM8916. However, so far it is not possible to make use of the virtualization features in the GICv2. To use KVM's VGICv2 code, the QGIC2 device tree node needs additional resources (according to binding documentation): - The CPU interface region (second reg) must be at least 8 KiB large to access the GICC_DIR register (mapped at 0x1000 offset) - Virtual control/CPU interface register base and size - Hypervisor maintenance interrupt Fortunately, the public APQ8016E TRM [2] provides the required information: - The CPU interface region (at 0x0B002000) actually has a size of 8 KiB - Virtual control/CPU interface register is at 0x0B001000/0x0B004000 - Hypervisor maintenance interrupt is "PPI #0" Note: This is a bit strange since almost all other ARM SoCs use GIC_PPI 9 for this. However, I have verified that this is indeed the interrupt that fires when bits are set in GICH_HCR. Add the additional resources to the QGIC2 device tree node in msm8916.dtsi. There is no functional difference when Linux is started in EL1 since the additional resources are ignored in that case. With these changes (and qhypstub), KVM seems to be fully working on the DragonBoard 410c (apq8016-sbc) and BQ Aquaris X5 (longcheer-l8910). [1]: https://github.com/msm8916-mainline/qhypstub [2]: https://developer.qualcomm.com/download/sd410/snapdragon-410e-technical-reference-manual.pdf Acked-by: Marc Zyngier Signed-off-by: Stephan Gerhold Link: https://lore.kernel.org/r/20210407163648.4708-1-stephan@gerhold.net Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8916.dtsi | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index 4c155735fbc9..4f06c0a9c425 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -1766,7 +1766,9 @@ compatible = "qcom,msm-qgic2"; interrupt-controller; #interrupt-cells = <3>; - reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>; + reg = <0x0b000000 0x1000>, <0x0b002000 0x2000>, + <0x0b001000 0x1000>, <0x0b004000 0x2000>; + interrupts = ; }; apcs: mailbox@b011000 { -- cgit From 7178d4cc0702bfe6a7e0f21e37d6e3dfe8e40f11 Mon Sep 17 00:00:00 2001 From: Jonathan Marek Date: Mon, 23 Nov 2020 09:37:05 -0500 Subject: arm64: dts: qcom: update usb qmp phy clock-cells property The top-level node doesn't provide any clocks, the subnode provides a single clock with of_clk_hw_simple_get. Signed-off-by: Jonathan Marek Link: https://lore.kernel.org/r/20201123143705.14277-1-jonathan@marek.ca Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sdm845.dtsi | 4 ++-- arch/arm64/boot/dts/qcom/sm8150.dtsi | 4 ++-- arch/arm64/boot/dts/qcom/sm8250.dtsi | 3 ++- 3 files changed, 6 insertions(+), 5 deletions(-) (limited to 'arch/arm64') diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi index 0b2077bce8fa..0a86fe71a66d 100644 --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi @@ -3685,7 +3685,6 @@ <0 0x088e8000 0 0x10>; reg-names = "reg-base", "dp_com"; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -3707,6 +3706,7 @@ <0 0x088e9600 0 0x128>, <0 0x088e9800 0 0x200>, <0 0x088e9a00 0 0x100>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; clock-names = "pipe0"; @@ -3718,7 +3718,6 @@ compatible = "qcom,sdm845-qmp-usb3-uni-phy"; reg = <0 0x088eb000 0 0x18c>; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -3738,6 +3737,7 @@ <0 0x088eb400 0 0x1fc>, <0 0x088eb800 0 0x218>, <0 0x088eb600 0 0x70>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; clock-names = "pipe0"; diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index 962882655188..51235a9521c2 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -2161,7 +2161,6 @@ <0 0x088e8000 0 0x10>; reg-names = "reg-base", "dp_com"; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -2183,6 +2182,7 @@ <0 0x088e9600 0 0x200>, <0 0x088e9800 0 0x200>, <0 0x088e9a00 0 0x100>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; clock-names = "pipe0"; @@ -2208,7 +2208,6 @@ compatible = "qcom,sm8150-qmp-usb3-uni-phy"; reg = <0 0x088eb000 0 0x200>; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -2228,6 +2227,7 @@ <0 0x088eb400 0 0x200>, <0 0x088eb800 0 0x800>, <0 0x088eb600 0 0x200>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; clock-names = "pipe0"; diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 9aeee4e415c3..4c0de12aaba6 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -2083,6 +2083,7 @@ <0 0x088e9600 0 0x200>, <0 0x088e9800 0 0x200>, <0 0x088e9a00 0 0x100>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; clock-names = "pipe0"; @@ -2108,7 +2109,6 @@ compatible = "qcom,sm8250-qmp-usb3-uni-phy"; reg = <0 0x088eb000 0 0x200>; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -2127,6 +2127,7 @@ reg = <0 0x088eb200 0 0x200>, <0 0x088eb400 0 0x200>, <0 0x088eb800 0 0x800>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; clock-names = "pipe0"; -- cgit