From b597a6f54280cdb20fb19c0224757f70cfb731c4 Mon Sep 17 00:00:00 2001 From: Baruch Siach Date: Tue, 16 Oct 2018 13:50:52 +0300 Subject: arm64: dts: clearfog-gt-8k: fix USB regulator gpio polarity The fixed regulator driver ignores the gpio flags, so this change has no practical effect in the current implementation. Fix it anyway to correct the hardware description. Signed-off-by: Baruch Siach Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts index 9473d40a292a..f03740d5ce62 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts @@ -42,7 +42,7 @@ v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 { compatible = "regulator-fixed"; - gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>; + gpio = <&cp0_gpio2 15 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&cp0_xhci_vbus_pins>; regulator-name = "v_5v0_usb3_hst_vbus"; -- cgit From babc5544c2933a5cbf9389679507dfa4911101ee Mon Sep 17 00:00:00 2001 From: Baruch Siach Date: Tue, 16 Oct 2018 13:50:53 +0300 Subject: arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal This reset signal controls the Marvell 1512 1G PHY. Note that current implementation queries the PHY over the MDIO bus (get_phy_device() call from of_mdiobus_register_phy()) before reset signal deassert. If the PHY reset signal is asserted at boot time, PHY registration fails. So current code relies on the bootloader to deassert the reset signal. Signed-off-by: Baruch Siach Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts index f03740d5ce62..f2e5b98f0c32 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts @@ -333,6 +333,10 @@ */ marvell,reg-init = <3 16 0 0x1017>; reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_copper_eth_phy_reset>; + reset-gpios = <&cp1_gpio1 11 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; }; switch0: switch0@4 { -- cgit From 235df2d80d3b196943043203bcb900325013a80a Mon Sep 17 00:00:00 2001 From: Baruch Siach Date: Fri, 19 Oct 2018 07:57:54 +0300 Subject: arm64: dts: clearfog-gt-8k: enable mini-PCIe CON2 USB Deassert the reset and wireless disable signals on the CON2 mini-PCIe socket. That allows the host to detect USB devices on the mini-PCIe socket. Signed-off-by: Baruch Siach Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts index f2e5b98f0c32..dfb26661a88e 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts @@ -246,6 +246,18 @@ gpios = <1 GPIO_ACTIVE_HIGH>; output-high; }; + + lte_reset { + gpio-hog; + gpios = <2 GPIO_ACTIVE_LOW>; + output-low; + }; + + lte_disable { + gpio-hog; + gpios = <21 GPIO_ACTIVE_LOW>; + output-low; + }; }; &cp0_ethernet { -- cgit From eefe328439642101774f0f5c4ea0dc6ba1cfb687 Mon Sep 17 00:00:00 2001 From: Ding Tao Date: Fri, 26 Oct 2018 11:50:27 +0000 Subject: arm64: dts: marvell: armada37xx: Add emmc/sdio pinctrl definition Add emmc/sdio pinctrl definition for marvell armada37xx SoCs. Signed-off-by: Ding Tao Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi index 4472bcd8f9fb..e05594ea15fb 100644 --- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi @@ -234,6 +234,11 @@ groups = "uart2"; function = "uart"; }; + + mmc_pins: mmc-pins { + groups = "emmc_nb"; + function = "emmc"; + }; }; nb_pm: syscon@14000 { @@ -266,6 +271,11 @@ function = "mii"; }; + sdio_pins: sdio-pins { + groups = "sdio_sb"; + function = "sdio"; + }; + }; eth0: ethernet@30000 { -- cgit From 43ebc7c1b3ed8198b9acf3019eca16e722f7331c Mon Sep 17 00:00:00 2001 From: Ding Tao Date: Fri, 26 Oct 2018 11:50:28 +0000 Subject: arm64: dts: marvell: armada-37xx: Enable emmc on espressobin The ESPRESSObin board has a emmc interface available on U11: declare it and let the bootloader enable it if the emmc is present. [gregory.clement@bootlin.com: disable the emmc by default] Signed-off-by: Ding Tao Signed-off-by: Gregory CLEMENT --- .../boot/dts/marvell/armada-3720-espressobin.dts | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts index 3ab25ad402b9..846003bb480c 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts @@ -60,9 +60,31 @@ cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>; marvell,pad-type = "sd"; vqmmc-supply = <&vcc_sd_reg1>; + + pinctrl-names = "default"; + pinctrl-0 = <&sdio_pins>; status = "okay"; }; +/* U11 */ +&sdhci0 { + non-removable; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs400-1_8v; + marvell,xenon-emmc; + marvell,xenon-tun-count = <9>; + marvell,pad-type = "fixed-1-8v"; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc_pins>; +/* + * This eMMC is not populated on all boards, so disable it by + * default and let the bootloader enable it, if it is present + */ + status = "disabled"; +}; + &spi0 { status = "okay"; -- cgit From b1f0bbe2700051886b954192b6c1751233fe0f52 Mon Sep 17 00:00:00 2001 From: Russell King Date: Mon, 5 Nov 2018 17:25:41 +0000 Subject: arm64: dts: add support for Macchiatobin Single Shot board Add DT support for the Macchiatobin Single Shot board from SolidRun, which is similar to the Double Shot board, but does not have the 10G 3310 PHYs - the two ethernet ports are instead connected directly to the SFP+ cages. Signed-off-by: Russell King Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/Makefile | 1 + .../dts/marvell/armada-8040-mcbin-singleshot.dts | 29 ++ arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts | 333 +------------------- arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi | 346 +++++++++++++++++++++ 4 files changed, 380 insertions(+), 329 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts create mode 100644 arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index eca8bac6303a..2eff1f927471 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -6,4 +6,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb +dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts b/arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts new file mode 100644 index 000000000000..c3e18fd5bc27 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts @@ -0,0 +1,29 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2016 Marvell Technology Group Ltd. + * + * Device Tree file for MACCHIATOBin Armada 8040 community board platform + */ + +#include "armada-8040-mcbin.dtsi" + +/ { + model = "Marvell 8040 MACCHIATOBin Single-shot"; + compatible = "marvell,armada8040-mcbin-singleshot", + "marvell,armada8040-mcbin", "marvell,armada8040", + "marvell,armada-ap806-quad", "marvell,armada-ap806"; +}; + +&cp0_eth0 { + status = "okay"; + phy-mode = "10gbase-kr"; + managed = "in-band-status"; + sfp = <&sfp_eth0>; +}; + +&cp1_eth0 { + status = "okay"; + phy-mode = "10gbase-kr"; + managed = "in-band-status"; + sfp = <&sfp_eth1>; +}; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts index 56fa44860909..d06f5ab7ddab 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dts @@ -5,226 +5,13 @@ * Device Tree file for MACCHIATOBin Armada 8040 community board platform */ -#include "armada-8040.dtsi" - -#include +#include "armada-8040-mcbin.dtsi" / { - model = "Marvell 8040 MACCHIATOBin"; - compatible = "marvell,armada8040-mcbin", "marvell,armada8040", + model = "Marvell 8040 MACCHIATOBin Double-shot"; + compatible = "marvell,armada8040-mcbin-doubleshot", + "marvell,armada8040-mcbin", "marvell,armada8040", "marvell,armada-ap806-quad", "marvell,armada-ap806"; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x0 0x0 0x80000000>; - }; - - aliases { - ethernet0 = &cp0_eth0; - ethernet1 = &cp1_eth0; - ethernet2 = &cp1_eth1; - ethernet3 = &cp1_eth2; - }; - - /* Regulator labels correspond with schematics */ - v_3_3: regulator-3-3v { - compatible = "regulator-fixed"; - regulator-name = "v_3_3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - status = "okay"; - }; - - v_vddo_h: regulator-1-8v { - compatible = "regulator-fixed"; - regulator-name = "v_vddo_h"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - status = "okay"; - }; - - v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 { - compatible = "regulator-fixed"; - enable-active-high; - gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_xhci_vbus_pins>; - regulator-name = "v_5v0_usb3_hst_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - status = "okay"; - }; - - usb3h0_phy: usb3_phy0 { - compatible = "usb-nop-xceiv"; - vcc-supply = <&v_5v0_usb3_hst_vbus>; - }; - - sfp_eth0: sfp-eth0 { - /* CON15,16 - CPM lane 4 */ - compatible = "sff,sfp"; - i2c-bus = <&sfpp0_i2c>; - los-gpio = <&cp1_gpio1 28 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp1_gpio1 27 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp1_gpio1 26 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_sfpp0_pins>; - }; - - sfp_eth1: sfp-eth1 { - /* CON17,18 - CPS lane 4 */ - compatible = "sff,sfp"; - i2c-bus = <&sfpp1_i2c>; - los-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp0_gpio2 30 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&cp1_sfpp1_pins &cp0_sfpp1_pins>; - }; - - sfp_eth3: sfp-eth3 { - /* CON13,14 - CPS lane 5 */ - compatible = "sff,sfp"; - i2c-bus = <&sfp_1g_i2c>; - los-gpio = <&cp0_gpio2 22 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp0_gpio2 21 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 24 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_sfp_1g_pins &cp1_sfp_1g_pins>; - }; -}; - -&uart0 { - status = "okay"; - pinctrl-0 = <&uart0_pins>; - pinctrl-names = "default"; -}; - -&ap_sdhci0 { - bus-width = <8>; - /* - * Not stable in HS modes - phy needs "more calibration", so add - * the "slow-mode" and disable SDR104, SDR50 and DDR50 modes. - */ - marvell,xenon-phy-slow-mode; - no-1-8-v; - no-sd; - no-sdio; - non-removable; - status = "okay"; - vqmmc-supply = <&v_vddo_h>; -}; - -&cp0_i2c0 { - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_i2c0_pins>; - status = "okay"; -}; - -&cp0_i2c1 { - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_i2c1_pins>; - status = "okay"; - - i2c-switch@70 { - compatible = "nxp,pca9548"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x70>; - - sfpp0_i2c: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - }; - sfpp1_i2c: i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - }; - sfp_1g_i2c: i2c@2 { - #address-cells = <1>; - #size-cells = <0>; - reg = <2>; - }; - }; -}; - -/* J25 UART header */ -&cp0_uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&cp0_uart1_pins>; - status = "okay"; -}; - -&cp0_mdio { - pinctrl-names = "default"; - pinctrl-0 = <&cp0_ge_mdio_pins>; - status = "okay"; - - ge_phy: ethernet-phy@0 { - reg = <0>; - }; -}; - -&cp0_pcie0 { - pinctrl-names = "default"; - pinctrl-0 = <&cp0_pcie_pins>; - num-lanes = <4>; - num-viewport = <8>; - reset-gpio = <&cp0_gpio1 20 GPIO_ACTIVE_LOW>; - status = "okay"; -}; - -&cp0_pinctrl { - cp0_ge_mdio_pins: ge-mdio-pins { - marvell,pins = "mpp32", "mpp34"; - marvell,function = "ge"; - }; - cp0_i2c1_pins: i2c1-pins { - marvell,pins = "mpp35", "mpp36"; - marvell,function = "i2c1"; - }; - cp0_i2c0_pins: i2c0-pins { - marvell,pins = "mpp37", "mpp38"; - marvell,function = "i2c0"; - }; - cp0_uart1_pins: uart1-pins { - marvell,pins = "mpp40", "mpp41"; - marvell,function = "uart1"; - }; - cp0_xhci_vbus_pins: xhci0-vbus-pins { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - cp0_sfp_1g_pins: sfp-1g-pins { - marvell,pins = "mpp51", "mpp53", "mpp54"; - marvell,function = "gpio"; - }; - cp0_pcie_pins: pcie-pins { - marvell,pins = "mpp52"; - marvell,function = "gpio"; - }; - cp0_sdhci_pins: sdhci-pins { - marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59", - "mpp60", "mpp61"; - marvell,function = "sdio"; - }; - cp0_sfpp1_pins: sfpp1-pins { - marvell,pins = "mpp62"; - marvell,function = "gpio"; - }; }; &cp0_xmdio { @@ -243,46 +30,11 @@ }; }; -&cp0_ethernet { - status = "okay"; -}; - &cp0_eth0 { status = "okay"; /* Network PHY */ phy = <&phy0>; phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp0_comphy4 0>; -}; - -&cp0_sata0 { - /* CPM Lane 0 - U29 */ - status = "okay"; -}; - -&cp0_sdhci0 { - /* U6 */ - broken-cd; - bus-width = <4>; - pinctrl-names = "default"; - pinctrl-0 = <&cp0_sdhci_pins>; - status = "okay"; - vqmmc-supply = <&v_3_3>; -}; - -&cp0_usb3_0 { - /* J38? - USB2.0 only */ - status = "okay"; -}; - -&cp0_usb3_1 { - /* J38? - USB2.0 only */ - status = "okay"; -}; - -&cp1_ethernet { - status = "okay"; }; &cp1_eth0 { @@ -290,81 +42,4 @@ /* Network PHY */ phy = <&phy8>; phy-mode = "10gbase-kr"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy4 0>; -}; - -&cp1_eth1 { - /* CPS Lane 0 - J5 (Gigabit RJ45) */ - status = "okay"; - /* Network PHY */ - phy = <&ge_phy>; - phy-mode = "sgmii"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy0 1>; -}; - -&cp1_eth2 { - /* CPS Lane 5 */ - status = "okay"; - /* Network PHY */ - phy-mode = "2500base-x"; - managed = "in-band-status"; - /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy5 2>; - sfp = <&sfp_eth3>; -}; - -&cp1_pinctrl { - cp1_sfpp1_pins: sfpp1-pins { - marvell,pins = "mpp8", "mpp10", "mpp11"; - marvell,function = "gpio"; - }; - cp1_spi1_pins: spi1-pins { - marvell,pins = "mpp12", "mpp13", "mpp14", "mpp15", "mpp16"; - marvell,function = "spi1"; - }; - cp1_uart0_pins: uart0-pins { - marvell,pins = "mpp6", "mpp7"; - marvell,function = "uart0"; - }; - cp1_sfp_1g_pins: sfp-1g-pins { - marvell,pins = "mpp24"; - marvell,function = "gpio"; - }; - cp1_sfpp0_pins: sfpp0-pins { - marvell,pins = "mpp26", "mpp27", "mpp28", "mpp29"; - marvell,function = "gpio"; - }; -}; - -/* J27 UART header */ -&cp1_uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&cp1_uart0_pins>; - status = "okay"; -}; - -&cp1_sata0 { - /* CPS Lane 1 - U32 */ - /* CPS Lane 3 - U31 */ - status = "okay"; -}; - -&cp1_spi1 { - pinctrl-names = "default"; - pinctrl-0 = <&cp1_spi1_pins>; - status = "okay"; - - spi-flash@0 { - compatible = "st,w25q32"; - spi-max-frequency = <50000000>; - reg = <0>; - }; -}; - -&cp1_usb3_0 { - /* CPS Lane 2 - CON7 */ - usb-phy = <&usb3h0_phy>; - status = "okay"; }; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi new file mode 100644 index 000000000000..29ea7e81ec4c --- /dev/null +++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi @@ -0,0 +1,346 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2016 Marvell Technology Group Ltd. + * + * Device Tree file for MACCHIATOBin Armada 8040 community board platform + */ + +#include "armada-8040.dtsi" + +#include + +/ { + model = "Marvell 8040 MACCHIATOBin"; + compatible = "marvell,armada8040-mcbin", "marvell,armada8040", + "marvell,armada-ap806-quad", "marvell,armada-ap806"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + aliases { + ethernet0 = &cp0_eth0; + ethernet1 = &cp1_eth0; + ethernet2 = &cp1_eth1; + ethernet3 = &cp1_eth2; + }; + + /* Regulator labels correspond with schematics */ + v_3_3: regulator-3-3v { + compatible = "regulator-fixed"; + regulator-name = "v_3_3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + status = "okay"; + }; + + v_vddo_h: regulator-1-8v { + compatible = "regulator-fixed"; + regulator-name = "v_vddo_h"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + status = "okay"; + }; + + v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_xhci_vbus_pins>; + regulator-name = "v_5v0_usb3_hst_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + status = "okay"; + }; + + usb3h0_phy: usb3_phy0 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&v_5v0_usb3_hst_vbus>; + }; + + sfp_eth0: sfp-eth0 { + /* CON15,16 - CPM lane 4 */ + compatible = "sff,sfp"; + i2c-bus = <&sfpp0_i2c>; + los-gpio = <&cp1_gpio1 28 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp1_gpio1 27 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp1_gpio1 26 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_sfpp0_pins>; + }; + + sfp_eth1: sfp-eth1 { + /* CON17,18 - CPS lane 4 */ + compatible = "sff,sfp"; + i2c-bus = <&sfpp1_i2c>; + los-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp0_gpio2 30 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_sfpp1_pins &cp0_sfpp1_pins>; + }; + + sfp_eth3: sfp-eth3 { + /* CON13,14 - CPS lane 5 */ + compatible = "sff,sfp"; + i2c-bus = <&sfp_1g_i2c>; + los-gpio = <&cp0_gpio2 22 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&cp0_gpio2 21 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp1_gpio1 24 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_sfp_1g_pins &cp1_sfp_1g_pins>; + }; +}; + +&uart0 { + status = "okay"; + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; +}; + +&ap_sdhci0 { + bus-width = <8>; + /* + * Not stable in HS modes - phy needs "more calibration", so add + * the "slow-mode" and disable SDR104, SDR50 and DDR50 modes. + */ + marvell,xenon-phy-slow-mode; + no-1-8-v; + no-sd; + no-sdio; + non-removable; + status = "okay"; + vqmmc-supply = <&v_vddo_h>; +}; + +&cp0_i2c0 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c0_pins>; + status = "okay"; +}; + +&cp0_i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c1_pins>; + status = "okay"; + + i2c-switch@70 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + sfpp0_i2c: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + sfpp1_i2c: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + sfp_1g_i2c: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + }; +}; + +/* J25 UART header */ +&cp0_uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_uart1_pins>; + status = "okay"; +}; + +&cp0_mdio { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_ge_mdio_pins>; + status = "okay"; + + ge_phy: ethernet-phy@0 { + reg = <0>; + }; +}; + +&cp0_pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&cp0_pcie_pins>; + num-lanes = <4>; + num-viewport = <8>; + reset-gpio = <&cp0_gpio1 20 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&cp0_pinctrl { + cp0_ge_mdio_pins: ge-mdio-pins { + marvell,pins = "mpp32", "mpp34"; + marvell,function = "ge"; + }; + cp0_i2c1_pins: i2c1-pins { + marvell,pins = "mpp35", "mpp36"; + marvell,function = "i2c1"; + }; + cp0_i2c0_pins: i2c0-pins { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + cp0_uart1_pins: uart1-pins { + marvell,pins = "mpp40", "mpp41"; + marvell,function = "uart1"; + }; + cp0_xhci_vbus_pins: xhci0-vbus-pins { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + cp0_sfp_1g_pins: sfp-1g-pins { + marvell,pins = "mpp51", "mpp53", "mpp54"; + marvell,function = "gpio"; + }; + cp0_pcie_pins: pcie-pins { + marvell,pins = "mpp52"; + marvell,function = "gpio"; + }; + cp0_sdhci_pins: sdhci-pins { + marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59", + "mpp60", "mpp61"; + marvell,function = "sdio"; + }; + cp0_sfpp1_pins: sfpp1-pins { + marvell,pins = "mpp62"; + marvell,function = "gpio"; + }; +}; + +&cp0_ethernet { + status = "okay"; +}; + +&cp0_eth0 { + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy4 0>; +}; + +&cp0_sata0 { + /* CPM Lane 0 - U29 */ + status = "okay"; +}; + +&cp0_sdhci0 { + /* U6 */ + broken-cd; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_sdhci_pins>; + status = "okay"; + vqmmc-supply = <&v_3_3>; +}; + +&cp0_usb3_0 { + /* J38? - USB2.0 only */ + status = "okay"; +}; + +&cp0_usb3_1 { + /* J38? - USB2.0 only */ + status = "okay"; +}; + +&cp1_ethernet { + status = "okay"; +}; + +&cp1_eth0 { + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy4 0>; +}; + +&cp1_eth1 { + /* CPS Lane 0 - J5 (Gigabit RJ45) */ + status = "okay"; + /* Network PHY */ + phy = <&ge_phy>; + phy-mode = "sgmii"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy0 1>; +}; + +&cp1_eth2 { + /* CPS Lane 5 */ + status = "okay"; + /* Network PHY */ + phy-mode = "2500base-x"; + managed = "in-band-status"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp1_comphy5 2>; + sfp = <&sfp_eth3>; +}; + +&cp1_pinctrl { + cp1_sfpp1_pins: sfpp1-pins { + marvell,pins = "mpp8", "mpp10", "mpp11"; + marvell,function = "gpio"; + }; + cp1_spi1_pins: spi1-pins { + marvell,pins = "mpp12", "mpp13", "mpp14", "mpp15", "mpp16"; + marvell,function = "spi1"; + }; + cp1_uart0_pins: uart0-pins { + marvell,pins = "mpp6", "mpp7"; + marvell,function = "uart0"; + }; + cp1_sfp_1g_pins: sfp-1g-pins { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; + cp1_sfpp0_pins: sfpp0-pins { + marvell,pins = "mpp26", "mpp27", "mpp28", "mpp29"; + marvell,function = "gpio"; + }; +}; + +/* J27 UART header */ +&cp1_uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&cp1_uart0_pins>; + status = "okay"; +}; + +&cp1_sata0 { + /* CPS Lane 1 - U32 */ + /* CPS Lane 3 - U31 */ + status = "okay"; +}; + +&cp1_spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&cp1_spi1_pins>; + status = "okay"; + + spi-flash@0 { + compatible = "st,w25q32"; + spi-max-frequency = <50000000>; + reg = <0>; + }; +}; + +&cp1_usb3_0 { + /* CPS Lane 2 - CON7 */ + usb-phy = <&usb3h0_phy>; + status = "okay"; +}; -- cgit From dfc1259a3f7a116b96e23e3467607c713c38a383 Mon Sep 17 00:00:00 2001 From: Baruch Siach Date: Thu, 6 Dec 2018 13:19:09 +0200 Subject: arm64: dts: clearfog-gt-8k: describe mini-PCIe CON2 USB Enable the USB3 peripheral that is wired to CON2 on the Clearfog GT-8K board. Signed-off-by: Baruch Siach Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts index dfb26661a88e..5b4a9609e31f 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts @@ -282,6 +282,10 @@ vqmmc-supply = <&v_3_3>; }; +&cp0_usb3_1 { + status = "okay"; +}; + &cp1_pinctrl { /* * MPP Bus: -- cgit