From 1b02383c385b16b4b275e30a3dd5860c0fd95c4a Mon Sep 17 00:00:00 2001
From: Marek Vasut <marex@denx.de>
Date: Sun, 23 Jun 2024 21:51:56 +0200
Subject: ARM: dts: stm32: Add ethernet support for DH STM32MP13xx DHCOR DHSBC
 board

Add ethernet support for the DH STM32MP13xx DHCOR DHSBC carrier board.
This carrier board is populated with two gigabit ethernet ports and two
Realtek RTL8211F PHYs, both are described in this DT patch.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
---
 arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts | 56 ++++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts b/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
index 5f4f6b6e427a..bacb70b4256b 100644
--- a/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
+++ b/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
@@ -22,6 +22,8 @@
 		     "st,stm32mp135";
 
 	aliases {
+		ethernet0 = &ethernet1;
+		ethernet1 = &ethernet2;
 		serial2 = &usart1;
 		serial3 = &usart2;
 	};
@@ -72,6 +74,60 @@
 	};
 };
 
+&ethernet1 {
+	phy-handle = <&ethphy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&eth1_rgmii_pins_a>;
+	pinctrl-1 = <&eth1_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	st,ext-phyclk;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		ethphy1: ethernet-phy@1 {
+			/* RTL8211F */
+			compatible = "ethernet-phy-id001c.c916";
+			interrupt-parent = <&gpiog>;
+			interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+			reg = <1>;
+			reset-assert-us = <15000>;
+			reset-deassert-us = <55000>;
+			reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&ethernet2 {
+	phy-handle = <&ethphy2>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&eth2_rgmii_pins_a>;
+	pinctrl-1 = <&eth2_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	st,ext-phyclk;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		ethphy2: ethernet-phy@1 {
+			/* RTL8211F */
+			compatible = "ethernet-phy-id001c.c916";
+			interrupt-parent = <&gpiog>;
+			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+			reg = <1>;
+			reset-assert-us = <15000>;
+			reset-deassert-us = <55000>;
+			reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
 &gpioa {
 	gpio-line-names = "", "", "", "",
 			  "", "DHSBC_USB_PWR_CC1", "", "",
-- 
cgit