| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Test that each supported packet trap is triggered under the right
conditions and that packets are indeed dropped and not forwarded.
Signed-off-by: Amit Cohen <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add proto parameter in order to enable the use of devlink_trap_cleanup()
in tests that use IPv6 protocol.
Signed-off-by: Amit Cohen <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
l2_drops_test() is used to check that drop traps are functioning as
intended. Currently it is only used in the layer 2 test, but it is also
useful for the layer 3 test introduced in the subsequent patch.
l2_drops_cleanup() is used to clean configurations and kill mausezahn
proccess.
Export the functions to the common devlink library to allow it to be
re-used by future tests.
Signed-off-by: Amit Cohen <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add tests to verify routes with source address set are deleted when
source address is deleted.
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix warnings on __u64 and pointer translation on arm and
other 32bit architectures. Since the pointer is 32bits on
those archs, we should not directly cast those types.
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Emilio López <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
Fix printf format warnings on arm (and other 32bit arch).
- udpgso.c and udpgso_bench_tx use %lu for size_t but it
should be unsigned long long on 32bit arch.
- so_txtime.c uses %ld for int64_t, but it should be
unsigned long long on 32bit arch.
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Willem de Bruijn <[email protected]>
Cc: David S. Miller <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
Use size_t and ssize_t correctly for counting send file size
instead of unsigned long and long, because long is 32bit on
32bit arch, which is not enough for counting long file size (>4GB).
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Eric Dumazet <[email protected]>
Cc: David S. Miller <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
Some virtual address range tests requires 64bit address space,
and we can not build and run those tests on the 32bit machine.
Filter the 64bit architectures in Makefile and run_vmtests,
so that those tests are built/run only on 64bit archs.
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Anshuman Khandual <[email protected]>
Cc: Aneesh Kumar K.V <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
Currently proc-self-map-files-002.c sets va_max (max test address
of user virtual address) to 4GB, but it is too big for 32bit
arch and 1UL << 32 is overflow on 32bit long.
Also since this value should be enough bigger than vm.mmap_min_addr
(64KB or 32KB by default), 1MB should be enough.
Make va_max 1MB unconditionally.
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Alexey Dobriyan <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
As per commit 131b30c94fbc ("kselftest: exclude failed TARGETS from
runlist") failed targets were excluded from the runlist. But value
$$INSTALL_PATH is always NULL. It should be $INSTALL_PATH instead
$$INSTALL_PATH.
So, fix Makefile to use $INSTALL_PATH.
Fixes: 131b30c94fbc ("kselftest: exclude failed TARGETS from runlist")
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: Cristian Marussi <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
The kselftest_module.sh file was not being installed by the Makefile
"install" target, rendering the lib/*.sh tests nonfunction. This fixes
that and takes the opportunity to move it into the kselftest/ subdirectory
which is where the kselftest infrastructure bits are collecting.
Reported-by: Naresh Kamboju <[email protected]>
Link: https://lore.kernel.org/lkml/CA+G9fYsfJpXQvOvHdjtg8z4a89dSStOQZOKa9zMjjQgWKng1aw@mail.gmail.com
Fixes: d3460527706e ("kselftest: Add test runner creation script")
Signed-off-by: Kees Cook <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
The default installation location for gen_kselftest_tar.sh was still
"kselftest/" which collides with the existing directory. Instead, this
moves the installation target into "kselftest_install/kselftest/" and
adjusts the tar creation accordingly. This also adjusts indentation and
logic to be consistent.
Fixes: 42d46e57ec97 ("selftests: Extract single-test shell logic from lib.mk")
Signed-off-by: Kees Cook <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
Since commit 5821ba969511 ("selftests: Add test plan API to kselftest.h
and adjust callers") accidentally introduced 'a' typo in the front of
run_test() function, breakpoint_test_arm64.c became not able to be
compiled.
Remove the 'a' from arun_test().
Fixes: 5821ba969511 ("selftests: Add test plan API to kselftest.h and adjust callers")
Reported-by: Jun Takahashi <[email protected]>
Signed-off-by: Masami Hiramatsu <[email protected]>
Cc: Kees Cook <[email protected]>
Reviewed-by: Kees Cook <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
Pull on for-linus to resolve what otherwise would have been a conflict
with the cgroups rstat patchset from Tejun.
* for-linus: (942 commits)
blkcg: make blkcg_print_stat() print stats only for online blkgs
nvme: change nvme_passthru_cmd64 to explicitly mark rsvd
nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths
nvme-rdma: fix a segmentation fault during module unload
iocost: don't nest spin_lock_irq in ioc_weight_write()
io_uring: ensure we clear io_kiocb->result before each issue
um-ubd: Entrust re-queue to the upper layers
nvme-multipath: remove unused groups_only mode in ana log
nvme-multipath: fix possible io hang after ctrl reconnect
io_uring: don't touch ctx in setup after ring fd install
io_uring: Fix leaked shadow_req
Linux 5.4-rc5
riscv: cleanup do_trap_break
nbd: verify socket is supported during setup
ata: libahci_platform: Fix regulator_get_optional() misuse
nbd: handle racing with error'ed out commands
nbd: protect cmd->status with cmd->lock
io_uring: fix bad inflight accounting for SETUP_IOPOLL|SETUP_SQTHREAD
io_uring: used cached copies of sq->dropped and cq->overflow
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
...
|
|
Access the skb->cb[] in the kfree_skb test.
Signed-off-by: Martin KaFai Lau <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Since the tool now adds support for another Intel SST implementation,
increment version number.
Signed-off-by: Srinivas Pandruvada <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
Some firmware implementation gives error when a command is sent get mask
for core count 32-61. So use core count to decide.
But there is no function to get core count. So introduce one function to
get core count.
Signed-off-by: Srinivas Pandruvada <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
Speed Select
There are some platforms, where there limited support of Intel(R) SST
features. Here perf-profile has only one base configuration and limited
support of commands. But still has support for discovery of base-freq and
turbo-freq features. So it is important to show minimum features to use
base-freq and turbo-freq features.
Here the change are:
- When there is no support of CONFIG_TDP_GET_LEVELS_INFO, then instead
of treating this as fatal error, treat this with number of config levels
= 0, that means only base level 0 is present.
- There is no support of mail box commands to get base frequencies or
turbo frequencies. Here present base frequency by reading cpufreq
base freq and turbo frequency by reading MSR 0x1AD.
- Don't display any field, which has value == 0.
Signed-off-by: Srinivas Pandruvada <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
Use different frequency weights for CLOS 0 and and CLOS1-3, to define
relative priority for power budgeting. This will be used for --auto
mode to enable base-freq and turbo-freq feature.
Signed-off-by: Srinivas Pandruvada <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
To be consistant with the other frequency units, change the CLOS
unit to MHz instead of ratios.
Signed-off-by: Srinivas Pandruvada <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
Use mailbox to read/write CLOS_PM_QOS_CONFIG instead of read/write to
MMIO offset.
Signed-off-by: Srinivas Pandruvada <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
There is an expectation in the CLX platform for SST base-freq feature that
Scaling min frequency be different for high and low priority cores.
This is the way the firmware will understand the priority.
So this change will look at high priority and low priority cores, and set
scaling_min_freq to P1High for high priority cores and P1Low to low
priority cores.
Signed-off-by: Srinivas Pandruvada <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
In CLX_N base_frequency is read from cpufreq sysfs, where units are in
KHz. The internal units in the code matches the real ratios which are
in 100MHz scale. So when storing units for CLX-N frequencies, convert
to 100MHz scale.
Signed-off-by: Srinivas Pandruvada <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
Make the avx level display consistent. Except for "turbo-ratio-limits-avx",
everywhere else it is avx2. So change "turbo-ratio-limits-avx"
to "turbo-ratio-limits-avx2".
Signed-off-by: Srinivas Pandruvada <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
Add support for uncore P0, uncore P1, P1 for base and AVX levels and
memory frequency. These commands are optional, so continue on
failure.
Signed-off-by: Srinivas Pandruvada <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
|
|
If we get ELF file with "maps" section, but no symbols pointing to it, we'll
end up with division by zero. Add check against this situation and exit early
with error. Found by Coverity scan against Github libbpf sources.
Fixes: bf82927125dd ("libbpf: refactor map initialization")
Signed-off-by: Andrii Nakryiko <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Perform size check always in btf__resolve_size. Makes the logic a bit more
robust against corrupted BTF and silences LGTM/Coverity complaining about
always true (size < 0) check.
Fixes: 69eaab04c675 ("btf: extract BTF type size calculation")
Signed-off-by: Andrii Nakryiko <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Fix few issues found by Coverity and LGTM.
Fixes: b053b439b72a ("bpf: libbpf: bpftool: Print bpf_line_info during prog dump")
Signed-off-by: Andrii Nakryiko <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Fix a potential overflow issue found by LGTM analysis, based on Github libbpf
source code.
Fixes: 3d65014146c6 ("bpf: libbpf: Add btf_line_info support to libbpf")
Signed-off-by: Andrii Nakryiko <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Coverity scan against Github libbpf code found the issue of not freeing memory and
leaving already freed memory still referenced from bpf_program. Fix it by
re-assigning successfully reallocated memory sooner.
Fixes: 2993e0515bb4 ("tools/bpf: add support to read .BTF.ext sections")
Signed-off-by: Andrii Nakryiko <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Fix issue reported by static analysis (Coverity). If bpf_prog_get_fd_by_id()
fails, xsk_lookup_bpf_maps() will fail as well and clean-up code will attempt
close() with fd=-1. Fix by checking bpf_prog_get_fd_by_id() return result and
exiting early.
Fixes: 10a13bb40e54 ("libbpf: remove qidconf and better support external bpf programs.")
Signed-off-by: Andrii Nakryiko <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
When compiling larger programs with bpf_asm, it's possible to
accidentally exceed jt/jf range, in which case it won't complain, but
rather silently emit a truncated offset, leading to a "happy debugging"
situation.
Add a warning to help detecting such issues. It could be made an error
instead, but this might break compilation of existing code (which might
be working by accident).
Signed-off-by: Ilya Leoshkevich <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Previous patch has implemented a new option "--total-cycles". But only
stdio mode is supported.
This patch supports the tui mode and support '--percent-limit'.
For example,
perf record -b ./div
perf report --total-cycles --percent-limit 1
# Samples: 2753248 of event 'cycles'
Sampled Cycles% Sampled Cycles Avg Cycles% Avg Cycles [Program Block Range] Shared Object
26.04% 2.8M 0.40% 18 [div.c:42 -> div.c:39] div
15.17% 1.2M 0.16% 7 [random_r.c:357 -> random_r.c:380] libc-2.27.so
5.11% 402.0K 0.04% 2 [div.c:27 -> div.c:28] div
4.87% 381.6K 0.04% 2 [random.c:288 -> random.c:291] libc-2.27.so
4.53% 381.0K 0.04% 2 [div.c:40 -> div.c:40] div
3.85% 300.9K 0.02% 1 [div.c:22 -> div.c:25] div
3.08% 241.1K 0.02% 1 [rand.c:26 -> rand.c:27] libc-2.27.so
3.06% 240.0K 0.02% 1 [random.c:291 -> random.c:291] libc-2.27.so
2.78% 215.7K 0.02% 1 [random.c:298 -> random.c:298] libc-2.27.so
2.52% 198.3K 0.02% 1 [random.c:293 -> random.c:293] libc-2.27.so
2.36% 184.8K 0.02% 1 [rand.c:28 -> rand.c:28] libc-2.27.so
2.33% 180.5K 0.02% 1 [random.c:295 -> random.c:295] libc-2.27.so
2.28% 176.7K 0.02% 1 [random.c:295 -> random.c:295] libc-2.27.so
2.20% 168.8K 0.02% 1 [rand@plt+0 -> rand@plt+0] div
1.98% 158.2K 0.02% 1 [random_r.c:388 -> random_r.c:388] libc-2.27.so
1.57% 123.3K 0.02% 1 [div.c:42 -> div.c:44] div
1.44% 116.0K 0.42% 19 [random_r.c:357 -> random_r.c:394] libc-2.27.so
--------------------------------------------------
v7:
---
1. Since we have used use_browser in report__browse_block_hists
to support stdio mode, now we also add supporting for tui.
2. Move block tui browser code from ui/browsers/hists.c
to block-info.c.
v6:
---
Create report__tui_browse_block_hists in block-info.c
(codes are moved from builtin-report.c).
v5:
---
Fix a crash issue when running perf report without
'--total-cycles'. The issue is because the internal flag
is renamed from 'total_cycles' to 'total_cycles_mode' in
previous patch but this patch still uses 'total_cycles'
to check if the '--total-cycles' option is enabled, which
causes the code to be inconsistent.
v4:
---
Since the block collection is moved out of printing in
previous patch, this patch is updated accordingly for
tui supporting.
v3:
---
Minor change since the function name is changed:
block_total_cycles_percent -> block_info__total_cycles_percent
Signed-off-by: Jin Yao <[email protected]>
Reviewed-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
We have already supported the '--total-cycles' option in previous patch.
It's also useful to show entries only above a threshold percent.
This patch enables '--percent-limit' for not showing entries
under that percent.
For example:
perf report --total-cycles --stdio --percent-limit 1
# To display the perf.data header info, please use --header/--header-only options.
#
#
# Total Lost Samples: 0
#
# Samples: 2M of event 'cycles'
# Event count (approx.): 2753248
#
# Sampled Cycles% Sampled Cycles Avg Cycles% Avg Cycles [Program Block Range] Shared Object
# ............... .............. ........... .......... ................................................................. ....................
#
26.04% 2.8M 0.40% 18 [div.c:42 -> div.c:39] div
15.17% 1.2M 0.16% 7 [random_r.c:357 -> random_r.c:380] libc-2.27.so
5.11% 402.0K 0.04% 2 [div.c:27 -> div.c:28] div
4.87% 381.6K 0.04% 2 [random.c:288 -> random.c:291] libc-2.27.so
4.53% 381.0K 0.04% 2 [div.c:40 -> div.c:40] div
3.85% 300.9K 0.02% 1 [div.c:22 -> div.c:25] div
3.08% 241.1K 0.02% 1 [rand.c:26 -> rand.c:27] libc-2.27.so
3.06% 240.0K 0.02% 1 [random.c:291 -> random.c:291] libc-2.27.so
2.78% 215.7K 0.02% 1 [random.c:298 -> random.c:298] libc-2.27.so
2.52% 198.3K 0.02% 1 [random.c:293 -> random.c:293] libc-2.27.so
2.36% 184.8K 0.02% 1 [rand.c:28 -> rand.c:28] libc-2.27.so
2.33% 180.5K 0.02% 1 [random.c:295 -> random.c:295] libc-2.27.so
2.28% 176.7K 0.02% 1 [random.c:295 -> random.c:295] libc-2.27.so
2.20% 168.8K 0.02% 1 [rand@plt+0 -> rand@plt+0] div
1.98% 158.2K 0.02% 1 [random_r.c:388 -> random_r.c:388] libc-2.27.so
1.57% 123.3K 0.02% 1 [div.c:42 -> div.c:44] div
1.44% 116.0K 0.42% 19 [random_r.c:357 -> random_r.c:394] libc-2.27.so
Committer testing:
From second exapmple onwards slightly edited for brevity:
# perf report --total-cycles --percent-limit 2 --stdio
# To display the perf.data header info, please use --header/--header-only options.
#
#
# Total Lost Samples: 0
#
# Samples: 6M of event 'cycles'
# Event count (approx.): 6299936
#
# Sampled Cycles% Sampled Cycles Avg Cycles% Avg Cycles [Program Block Range] Shared Object
# ............... .............. ........... .......... ...................................................................... ....................
#
2.17% 1.7M 0.08% 607 [compiler.h:199 -> common.c:221] [kernel.vmlinux]
#
# (Tip: Create an archive with symtabs to analyse on other machine: perf archive)
#
# perf report --total-cycles --percent-limit 1 --stdio
# Sampled Cycles% Sampled Cycles Avg Cycles% Avg Cycles [Program Block Range] Shared Object
2.17% 1.7M 0.08% 607 [compiler.h:199 -> common.c:221] [kernel.vmlinux]
1.75% 1.3M 8.34% 65.5K [memset-vec-unaligned-erms.S:147 -> memset-vec-unaligned-erms.S:151] libc-2.29.so
#
# perf report --total-cycles --percent-limit 0.7 --stdio
# Sampled Cycles% Sampled Cycles Avg Cycles% Avg Cycles [Program Block Range] Shared Object
2.17% 1.7M 0.08% 607 [compiler.h:199 -> common.c:221] [kernel.vmlinux]
1.75% 1.3M 8.34% 65.5K [memset-vec-unaligned-erms.S:147 -> memset-vec-unaligned-erms.S:151] libc-2.29.so
0.72% 544.5K 0.03% 230 [entry_64.S:657 -> entry_64.S:662] [kernel.vmlinux]
#
-------------------------------------------
It only shows the entries which 'Sampled Cycles%' > 1%.
v7:
---
No functional change. Only fix the conflict issue because
previous patches are changed.
v6:
---
No functional change. Only fix the conflict issue because
previous patches are changed.
v5:
---
No functional change. Only fix the conflict issue because
previous patches are changed.
v4:
---
No functional change. Only fix the build issue because
previous patches are changed.
Signed-off-by: Jin Yao <[email protected]>
Reviewed-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
It would be useful to support sorting for all blocks by the sampled
cycles percent per block. This is useful to concentrate on the globally
hottest blocks.
This patch implements a new option "--total-cycles" which sorts all
blocks by 'Sampled Cycles%'. The 'Sampled Cycles%' is the percent:
percent = block sampled cycles aggregation / total sampled cycles
Note that, this patch only supports "--stdio" mode.
For example,
# perf record -b ./div
# perf report --total-cycles --stdio
# To display the perf.data header info, please use --header/--header-only options.
#
# Total Lost Samples: 0
#
# Samples: 2M of event 'cycles'
# Event count (approx.): 2753248
#
# Sampled Cycles% Sampled Cycles Avg Cycles% Avg Cycles [Program Block Range] Shared Object
# ............... .............. ........... .......... ................................................ .................
#
26.04% 2.8M 0.40% 18 [div.c:42 -> div.c:39] div
15.17% 1.2M 0.16% 7 [random_r.c:357 -> random_r.c:380] libc-2.27.so
5.11% 402.0K 0.04% 2 [div.c:27 -> div.c:28] div
4.87% 381.6K 0.04% 2 [random.c:288 -> random.c:291] libc-2.27.so
4.53% 381.0K 0.04% 2 [div.c:40 -> div.c:40] div
3.85% 300.9K 0.02% 1 [div.c:22 -> div.c:25] div
3.08% 241.1K 0.02% 1 [rand.c:26 -> rand.c:27] libc-2.27.so
3.06% 240.0K 0.02% 1 [random.c:291 -> random.c:291] libc-2.27.so
2.78% 215.7K 0.02% 1 [random.c:298 -> random.c:298] libc-2.27.so
2.52% 198.3K 0.02% 1 [random.c:293 -> random.c:293] libc-2.27.so
2.36% 184.8K 0.02% 1 [rand.c:28 -> rand.c:28] libc-2.27.so
2.33% 180.5K 0.02% 1 [random.c:295 -> random.c:295] libc-2.27.so
2.28% 176.7K 0.02% 1 [random.c:295 -> random.c:295] libc-2.27.so
2.20% 168.8K 0.02% 1 [rand@plt+0 -> rand@plt+0] div
1.98% 158.2K 0.02% 1 [random_r.c:388 -> random_r.c:388] libc-2.27.so
1.57% 123.3K 0.02% 1 [div.c:42 -> div.c:44] div
1.44% 116.0K 0.42% 19 [random_r.c:357 -> random_r.c:394] libc-2.27.so
0.25% 182.5K 0.02% 1 [random_r.c:388 -> random_r.c:391] libc-2.27.so
0.00% 48 1.07% 48 [x86_pmu_enable+284 -> x86_pmu_enable+298] [kernel.kallsyms]
0.00% 74 1.64% 74 [vm_mmap_pgoff+0 -> vm_mmap_pgoff+92] [kernel.kallsyms]
0.00% 73 1.62% 73 [vm_mmap+0 -> vm_mmap+48] [kernel.kallsyms]
0.00% 63 0.69% 31 [up_write+0 -> up_write+34] [kernel.kallsyms]
0.00% 13 0.29% 13 [setup_arg_pages+396 -> setup_arg_pages+413] [kernel.kallsyms]
0.00% 3 0.07% 3 [setup_arg_pages+418 -> setup_arg_pages+450] [kernel.kallsyms]
0.00% 616 6.84% 308 [security_mmap_file+0 -> security_mmap_file+72] [kernel.kallsyms]
0.00% 23 0.51% 23 [security_mmap_file+77 -> security_mmap_file+87] [kernel.kallsyms]
0.00% 4 0.02% 1 [sched_clock+0 -> sched_clock+4] [kernel.kallsyms]
0.00% 4 0.02% 1 [sched_clock+9 -> sched_clock+12] [kernel.kallsyms]
0.00% 1 0.02% 1 [rcu_nmi_exit+0 -> rcu_nmi_exit+9] [kernel.kallsyms]
Committer testing:
This should provide material for hours of endless joy, both from looking
for suspicious things in the implementation of this patch, such as the
top one:
# Sampled Cycles% Sampled Cycles Avg Cycles% Avg Cycles [Program Block Range] Shared Object
2.17% 1.7M 0.08% 607 [compiler.h:199 -> common.c:221] [kernel.vmlinux]
As well from things that look legit:
# Sampled Cycles% Sampled Cycles Avg Cycles% Avg Cycles [Program Block Range] Shared Object
0.16% 123.0K 0.60% 4.7K [nospec-branch.h:265 -> nospec-branch.h:278] [kernel.vmlinux]
:-)
Very short system wide taken branches session:
# perf record -h -b
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-b, --branch-any sample any taken branches
#
# perf record -b
^C[ perf record: Woken up 595 times to write data ]
[ perf record: Captured and wrote 156.672 MB perf.data (196873 samples) ]
#
# perf evlist -v
cycles: size: 112, { sample_period, sample_freq }: 4000, sample_type: IP|TID|TIME|CPU|PERIOD|BRANCH_STACK, read_format: ID, disabled: 1, inherit: 1, mmap: 1, comm: 1, freq: 1, task: 1, precise_ip: 3, sample_id_all: 1, exclude_guest: 1, mmap2: 1, comm_exec: 1, ksymbol: 1, bpf_event: 1, branch_sample_type: ANY
#
# perf report --total-cycles --stdio
# To display the perf.data header info, please use --header/--header-only options.
#
# Total Lost Samples: 0
#
# Samples: 6M of event 'cycles'
# Event count (approx.): 6299936
#
# Sampled Cycles% Sampled Cycles Avg Cycles% Avg Cycles [Program Block Range] Shared Object
# ............... .............. ........... .......... ...................................................................... ....................
#
2.17% 1.7M 0.08% 607 [compiler.h:199 -> common.c:221] [kernel.vmlinux]
1.75% 1.3M 8.34% 65.5K [memset-vec-unaligned-erms.S:147 -> memset-vec-unaligned-erms.S:151] libc-2.29.so
0.72% 544.5K 0.03% 230 [entry_64.S:657 -> entry_64.S:662] [kernel.vmlinux]
0.56% 541.8K 0.09% 672 [compiler.h:199 -> common.c:300] [kernel.vmlinux]
0.39% 293.2K 0.01% 104 [list_debug.c:43 -> list_debug.c:61] [kernel.vmlinux]
0.36% 278.6K 0.03% 272 [entry_64.S:1289 -> entry_64.S:1308] [kernel.vmlinux]
0.30% 260.8K 0.07% 564 [clear_page_64.S:47 -> clear_page_64.S:50] [kernel.vmlinux]
0.28% 215.3K 0.05% 369 [traps.c:623 -> traps.c:628] [kernel.vmlinux]
0.23% 178.1K 0.04% 278 [entry_64.S:271 -> entry_64.S:275] [kernel.vmlinux]
0.20% 152.6K 0.09% 706 [paravirt.c:177 -> paravirt.c:179] [kernel.vmlinux]
0.20% 155.8K 0.05% 373 [entry_64.S:153 -> entry_64.S:175] [kernel.vmlinux]
0.18% 136.6K 0.03% 222 [msr.h:105 -> msr.h:166] [kernel.vmlinux]
0.16% 123.0K 0.60% 4.7K [nospec-branch.h:265 -> nospec-branch.h:278] [kernel.vmlinux]
0.16% 118.3K 0.01% 44 [entry_64.S:632 -> entry_64.S:657] [kernel.vmlinux]
0.14% 104.5K 0.00% 28 [rwsem.c:1541 -> rwsem.c:1544] [kernel.vmlinux]
0.13% 99.2K 0.01% 53 [spinlock.c:150 -> spinlock.c:152] [kernel.vmlinux]
0.13% 95.5K 0.00% 35 [swap.c:456 -> swap.c:471] [kernel.vmlinux]
0.12% 96.2K 0.05% 407 [copy_user_64.S:175 -> copy_user_64.S:209] [kernel.vmlinux]
0.11% 85.9K 0.00% 31 [swap.c:400 -> page-flags.h:188] [kernel.vmlinux]
0.10% 73.0K 0.01% 52 [paravirt.h:763 -> list.h:131] [kernel.vmlinux]
0.07% 56.2K 0.03% 214 [filemap.c:1524 -> filemap.c:1557] [kernel.vmlinux]
0.07% 54.2K 0.02% 145 [memory.c:1032 -> memory.c:1049] [kernel.vmlinux]
0.07% 50.3K 0.00% 39 [mmzone.c:49 -> mmzone.c:69] [kernel.vmlinux]
0.06% 48.3K 0.01% 40 [paravirt.h:768 -> page_alloc.c:3304] [kernel.vmlinux]
0.06% 46.7K 0.02% 155 [memory.c:1032 -> memory.c:1056] [kernel.vmlinux]
0.06% 46.9K 0.01% 103 [swap.c:867 -> swap.c:902] [kernel.vmlinux]
0.06% 47.8K 0.00% 34 [entry_64.S:1201 -> entry_64.S:1202] [kernel.vmlinux]
-----------------------------------------------------------
v7:
---
Use use_browser in report__browse_block_hists for supporting
stdio and potential tui mode.
v6:
---
Create report__browse_block_hists in block-info.c (codes are
moved from builtin-report.c). It's called from
perf_evlist__tty_browse_hists.
v5:
---
1. Move all block functions to block-info.c
2. Move the code of setting ms in block hist_entry to
other patch.
v4:
---
1. Use new option '--total-cycles' to replace
'-s total_cycles' in v3.
2. Move block info collection out of block info
printing.
v3:
---
1. Use common function block_info__process_sym to
process the blocks per symbol.
2. Remove the nasty hack for skipping calculation
of column length
3. Some minor cleanup
Signed-off-by: Jin Yao <[email protected]>
Reviewed-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
This patch provides helper routines to support new columns for block
info output.
The new columns are:
Sampled Cycles%
Sampled Cycles
Avg Cycles%
Avg Cycles
[Program Block Range]
Shared Object
v5:
---
1. Move more block related functions from builtin-report.c to
block-info.c
2. Set ms (map+sym) in block hist_entry. Because this info
is needed for reporting the block range (i.e. source line)
Committer notes:
Remove unused set_fmt() function, some build were not completing with:
util/block-info.c:396:20: error: unused function 'set_fmt' [-Werror,-Wunused-function]
static inline void set_fmt(struct block_fmt *block_fmt,
^
1 error generated.
Signed-off-by: Jin Yao <[email protected]>
Reviewed-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux
Pull cpupower utility updates for v5.5 from Shuah Khan:
"This cpupower update for Linux 5.5-rc1 consists of bug fixes and
improvements to make it more accurate by removing the userspace
to kernel transition and read_msr initiated IPI delays."
* tag 'linux-cpupower-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux:
cpupower: ToDo: Update ToDo with ideas for per_cpu_schedule handling
cpupower: mperf_monitor: Update cpupower to use the RDPRU instruction
cpupower: mperf_monitor: Introduce per_cpu_schedule flag
cpupower: Move needs_root variable into a sub-struct
cpupower : Handle set and info subcommands correctly
tools/power/cpupower: Fix initializer override in hsw_ext_cstates
|
|
We can get the per sample cycles by hist__account_cycles(). It's also
useful to know the total cycles of all samples in order to get the
cycles coverage for a single program block in further. For example:
coverage = per block sampled cycles / total sampled cycles
This patch creates a new argument 'total_cycles' in hist__account_cycles(),
which will be added with the cycles of each sample.
Signed-off-by: Jin Yao <[email protected]>
Reviewed-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
We have already implemented some block-info related functions.
Now it's time to do some cleanup, refactoring and move the
functions and structures to new block-info.h/block-info.c.
v4:
---
Move code for skipping column length calculation to patch:
'perf diff: Don't use hack to skip column length calculation'
v3:
---
1. Rename the patch title
2. Rename from block.h/block.c to block-info.h/block-info.c
3. Move more common part to block-info, such as
block_info__process_sym.
4. Remove the nasty hack for skipping calculation of column
length
Signed-off-by: Jin Yao <[email protected]>
Reviewed-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Previously we use a nasty hack to skip the hists__calc_col_len for block
since this function is not very suitable for block column length
calculation.
This patch removes the hack code and add a check at the entry of
hists__calc_col_len to skip for block case.
Signed-off-by: Jin Yao <[email protected]>
Reviewed-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The test case 'Read backward ring buffer' failed on 32-bit architectures
which were found by LKFT perf testing. The test failed on arm32 x15
device, qemu_arm32, qemu_i386, and found intermittent failure on i386;
the failure log is as below:
50: Read backward ring buffer :
--- start ---
test child forked, pid 510
Using CPUID GenuineIntel-6-9E-9
mmap size 1052672B
mmap size 8192B
Finished reading overwrite ring buffer: rewind
free(): invalid next size (fast)
test child interrupted
---- end ----
Read backward ring buffer: FAILED!
The log hints there have issue for memory usage, thus free() reports
error 'invalid next size' and directly exit for the case. Finally, this
issue is root caused as out of bounds memory access for the data array
'evsel->id'.
The backward ring buffer test invokes do_test() twice. 'evsel->id' is
allocated at the first call with the flow:
test__backward_ring_buffer()
`-> do_test()
`-> evlist__mmap()
`-> evlist__mmap_ex()
`-> perf_evsel__alloc_id()
So 'evsel->id' is allocated with one item, and it will be used in
function perf_evlist__id_add():
evsel->id[0] = id
evsel->ids = 1
At the second call for do_test(), it skips to initialize 'evsel->id'
and reuses the array which is allocated in the first call. But
'evsel->ids' contains the stale value. Thus:
evsel->id[1] = id -> out of bound access
evsel->ids = 2
To fix this issue, we will use evlist__open() and evlist__close() pair
functions to prepare and cleanup context for evlist; so 'evsel->id' and
'evsel->ids' can be initialized properly when invoke do_test() and avoid
the out of bounds memory access.
Fixes: ee74701ed8ad ("perf tests: Add test to check backward ring buffer")
Signed-off-by: Leo Yan <[email protected]>
Reviewed-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Naresh Kamboju <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Wang Nan <[email protected]>
Cc: [email protected] # v4.10+
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The patch adds a new option to limit the output file size, then based on
it, we can create a wrapper of the perf command that uses the option to
avoid exhausting the disk space by the unconscious user.
In order to make the perf.data parsable, we just limit the sample data
size, since the perf.data consists of many headers and sample data and
other data, the actual size of the recorded file will bigger than the
setting value.
Testing it:
# ./perf record -a -g --max-size=10M
Couldn't synthesize bpf events.
[ perf record: perf size limit reached (10249 KB), stopping session ]
[ perf record: Woken up 32 times to write data ]
[ perf record: Captured and wrote 10.133 MB perf.data (71964 samples) ]
# ls -lh perf.data
-rw------- 1 root root 11M Oct 22 14:32 perf.data
# ./perf record -a -g --max-size=10K
[ perf record: perf size limit reached (10 KB), stopping session ]
Couldn't synthesize bpf events.
[ perf record: Woken up 0 times to write data ]
[ perf record: Captured and wrote 1.546 MB perf.data (69 samples) ]
# ls -l perf.data
-rw------- 1 root root 1626952 Oct 22 14:36 perf.data
Committer notes:
Fixed the build in multiple distros by using PRIu64 to print u64 struct
members, fixing this:
builtin-record.c: In function 'record__write':
builtin-record.c:150:5: error: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'u64' [-Werror=format=]
rec->bytes_written >> 10);
^
CC /tmp/build/pe
Signed-off-by: Jiwei Sun <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Michael Petlan <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Richard Danter <[email protected]>
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Since debuginfo__find_probes() callback function can be called with the
location which already passed, the callback function must filter out
such overlapped locations.
add_probe_trace_event() has already done it by commit 1a375ae7659a
("perf probe: Skip same probe address for a given line"), but
add_available_vars() doesn't. Thus perf probe -v shows same address
repeatedly as below:
# perf probe -V vfs_read:18
Available variables at vfs_read:18
@<vfs_read+217>
char* buf
loff_t* pos
ssize_t ret
struct file* file
@<vfs_read+217>
char* buf
loff_t* pos
ssize_t ret
struct file* file
@<vfs_read+226>
char* buf
loff_t* pos
ssize_t ret
struct file* file
With this fix, perf probe -V shows it correctly:
# perf probe -V vfs_read:18
Available variables at vfs_read:18
@<vfs_read+217>
char* buf
loff_t* pos
ssize_t ret
struct file* file
@<vfs_read+226>
char* buf
loff_t* pos
ssize_t ret
struct file* file
Fixes: cf6eb489e5c0 ("perf probe: Show accessible local variables")
Signed-off-by: Masami Hiramatsu <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Link: http://lore.kernel.org/lkml/157241938927.32002.4026859017790562751.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Fix to show calling lines of inlined functions (where an inline function
is called).
die_walk_lines() filtered out the lines inside inlined functions based
on the address. However this also filtered out the lines which call
those inlined functions from the target function.
To solve this issue, check the call_file and call_line attributes and do
not filter out if it matches to the line information.
Without this fix, perf probe -L doesn't show some lines correctly.
(don't see the lines after 17)
# perf probe -L vfs_read
<vfs_read@/home/mhiramat/ksrc/linux/fs/read_write.c:0>
0 ssize_t vfs_read(struct file *file, char __user *buf, size_t count, loff_t *pos)
1 {
2 ssize_t ret;
4 if (!(file->f_mode & FMODE_READ))
return -EBADF;
6 if (!(file->f_mode & FMODE_CAN_READ))
return -EINVAL;
8 if (unlikely(!access_ok(buf, count)))
return -EFAULT;
11 ret = rw_verify_area(READ, file, pos, count);
12 if (!ret) {
13 if (count > MAX_RW_COUNT)
count = MAX_RW_COUNT;
15 ret = __vfs_read(file, buf, count, pos);
16 if (ret > 0) {
fsnotify_access(file);
add_rchar(current, ret);
}
With this fix:
# perf probe -L vfs_read
<vfs_read@/home/mhiramat/ksrc/linux/fs/read_write.c:0>
0 ssize_t vfs_read(struct file *file, char __user *buf, size_t count, loff_t *pos)
1 {
2 ssize_t ret;
4 if (!(file->f_mode & FMODE_READ))
return -EBADF;
6 if (!(file->f_mode & FMODE_CAN_READ))
return -EINVAL;
8 if (unlikely(!access_ok(buf, count)))
return -EFAULT;
11 ret = rw_verify_area(READ, file, pos, count);
12 if (!ret) {
13 if (count > MAX_RW_COUNT)
count = MAX_RW_COUNT;
15 ret = __vfs_read(file, buf, count, pos);
16 if (ret > 0) {
17 fsnotify_access(file);
18 add_rchar(current, ret);
}
20 inc_syscr(current);
}
Fixes: 4cc9cec636e7 ("perf probe: Introduce lines walker interface")
Signed-off-by: Masami Hiramatsu <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Link: http://lore.kernel.org/lkml/157241937995.32002.17899884017011512577.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Filter out instances except for inlined_subroutine and subprogram DIE in
die_walk_instances() and die_is_func_instance().
This fixes an issue that perf probe sets some probes on calling address
instead of a target function itself.
When perf probe walks on instances of an abstruct origin (a kind of
function prototype of inlined function), die_walk_instances() can also
pass a GNU_call_site (a GNU extension for call site) to callback. Since
it is not an inlined instance of target function, we have to filter out
when searching a probe point.
Without this patch, perf probe sets probes on call site address too.This
can happen on some function which is marked "inlined", but has actual
symbol. (I'm not sure why GCC mark it "inlined"):
# perf probe -D vfs_read
p:probe/vfs_read _text+2500017
p:probe/vfs_read_1 _text+2499468
p:probe/vfs_read_2 _text+2499563
p:probe/vfs_read_3 _text+2498876
p:probe/vfs_read_4 _text+2498512
p:probe/vfs_read_5 _text+2498627
With this patch:
Slightly different results, similar tho:
# perf probe -D vfs_read
p:probe/vfs_read _text+2498512
Committer testing:
# uname -a
Linux quaco 5.3.8-200.fc30.x86_64 #1 SMP Tue Oct 29 14:46:22 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux
Before:
# perf probe -D vfs_read
p:probe/vfs_read _text+3131557
p:probe/vfs_read_1 _text+3130975
p:probe/vfs_read_2 _text+3131047
p:probe/vfs_read_3 _text+3130380
p:probe/vfs_read_4 _text+3130000
# uname -a
Linux quaco 5.3.8-200.fc30.x86_64 #1 SMP Tue Oct 29 14:46:22 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux
#
After:
# perf probe -D vfs_read
p:probe/vfs_read _text+3130000
#
Fixes: db0d2c6420ee ("perf probe: Search concrete out-of-line instances")
Signed-off-by: Masami Hiramatsu <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Link: http://lore.kernel.org/lkml/157241937063.32002.11024544873990816590.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Skip end-of-sequence and non-statement lines while walking through lines
list.
The "end-of-sequence" line information means:
"the current address is that of the first byte after the
end of a sequence of target machine instructions."
(DWARF version 4 spec 6.2.2)
This actually means out of scope and we can not probe on it.
On the other hand, the statement lines (is_stmt) means:
"the current instruction is a recommended breakpoint location.
A recommended breakpoint location is intended to “represent”
a line, a statement and/or a semantically distinct subpart
of a statement."
(DWARF version 4 spec 6.2.2)
So, non-statement line info also should be skipped.
These can reduce unneeded probe points and also avoid an error.
E.g. without this patch:
# perf probe -a "clear_tasks_mm_cpumask:1"
Added new events:
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask:1)
probe:clear_tasks_mm_cpumask_1 (on clear_tasks_mm_cpumask:1)
probe:clear_tasks_mm_cpumask_2 (on clear_tasks_mm_cpumask:1)
probe:clear_tasks_mm_cpumask_3 (on clear_tasks_mm_cpumask:1)
probe:clear_tasks_mm_cpumask_4 (on clear_tasks_mm_cpumask:1)
You can now use it in all perf tools, such as:
perf record -e probe:clear_tasks_mm_cpumask_4 -aR sleep 1
#
This puts 5 probes on one line, but acutally it's not inlined function.
This is because there are many non statement instructions at the
function prologue.
With this patch:
# perf probe -a "clear_tasks_mm_cpumask:1"
Added new event:
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask:1)
You can now use it in all perf tools, such as:
perf record -e probe:clear_tasks_mm_cpumask -aR sleep 1
#
Now perf-probe skips unneeded addresses.
Committer testing:
Slightly different results, but similar:
Before:
# uname -a
Linux quaco 5.3.8-200.fc30.x86_64 #1 SMP Tue Oct 29 14:46:22 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux
#
# perf probe -a "clear_tasks_mm_cpumask:1"
Added new events:
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask:1)
probe:clear_tasks_mm_cpumask_1 (on clear_tasks_mm_cpumask:1)
probe:clear_tasks_mm_cpumask_2 (on clear_tasks_mm_cpumask:1)
You can now use it in all perf tools, such as:
perf record -e probe:clear_tasks_mm_cpumask_2 -aR sleep 1
#
After:
# perf probe -a "clear_tasks_mm_cpumask:1"
Added new event:
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask:1)
You can now use it in all perf tools, such as:
perf record -e probe:clear_tasks_mm_cpumask -aR sleep 1
# perf probe -l
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask@kernel/cpu.c)
#
Fixes: 4cc9cec636e7 ("perf probe: Introduce lines walker interface")
Signed-off-by: Masami Hiramatsu <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Link: http://lore.kernel.org/lkml/157241936090.32002.12156347518596111660.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Make find_best_scope() returns innermost DIE at given address if there
is no best matched scope DIE. Since Gcc sometimes generates intuitively
strange line info which is out of inlined function address range, we
need this fixup.
Without this, sometimes perf probe failed to probe on a line inside an
inlined function:
# perf probe -D ksys_open:3
Failed to find scope of probe point.
Error: Failed to add events.
With this fix, 'perf probe' can probe it:
# perf probe -D ksys_open:3
p:probe/ksys_open _text+25707308
p:probe/ksys_open_1 _text+25710596
p:probe/ksys_open_2 _text+25711114
p:probe/ksys_open_3 _text+25711343
p:probe/ksys_open_4 _text+25714058
p:probe/ksys_open_5 _text+2819653
p:probe/ksys_open_6 _text+2819701
Signed-off-by: Masami Hiramatsu <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Ravi Bangoria <[email protected]>
Cc: Steven Rostedt (VMware) <[email protected]>
Cc: Tom Zanussi <[email protected]>
Link: http://lore.kernel.org/lkml/157291300887.19771.14936015360963292236.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Fix expand_tabs that copies the source lines '\0' and then appends
another '\0' at a potentially out of bounds address.
Signed-off-by: Ian Rogers <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Song Liu <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lore.kernel.org/lkml/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
To reduce boilerplate in some places.
Cc: Adrian Hunter <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Its sufficient to check if map->groups is NULL before using it to get
->machine value.
Cc: Adrian Hunter <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|