| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The tool uses topo.max_cpu_num to determine number of entries needed for
fd_percpu[] and irqs_per_cpu[]. For example on a system with 4 CPUs
topo.max_cpu_num is 3 so we get too small array for holding per-CPU items.
Fix this to use right number of entries, which is topo.max_cpu_num + 1.
Signed-off-by: Mika Westerberg <[email protected]>
Signed-off-by: Len Brown <[email protected]>
|
|
Switch to tab-delimited output from fixed-width columns
to make it simpler to import into spreadsheets.
As the fixed width columnns were 8-spaces wide,
the output on the screen should not change.
Signed-off-by: Len Brown <[email protected]>
|
|
turbostat gives valid results across suspend to idle, aka freeze,
whether invoked in interval mode, or in command mode.
Indeed, this can be used to measure suspend to idle:
turbostat echo freeze > /sys/power/state
But this does not work across suspend to ACPI S3, because the
processor counters, including the TSC, are reset on resume.
Further, when turbostat detects a problem, it does't forgive
the hardware, and interval mode will print *'s from there on out.
Instead, upon detecting counters going backwards, simply
reset and start over.
Interval mode across ACPI S3: (observe TSC going backwards)
root@sharkbay:/home/lenb/turbostat-src# ./turbostat -M 0x10
CPU Avg_MHz Busy% Bzy_MHz TSC_MHz MSR 0x010
- 1 0.06 858 2294 0x0000000000000000
0 0 0.06 847 2294 0x0000002a254b98ac
1 1 0.06 878 2294 0x0000002a254efa3a
2 1 0.07 843 2294 0x0000002a2551df65
3 0 0.05 863 2294 0x0000002a2553fea2
turbostat: re-initialized with num_cpus 4
CPU Avg_MHz Busy% Bzy_MHz TSC_MHz MSR 0x010
- 2 0.20 849 2294 0x0000000000000000
0 2 0.26 856 2294 0x0000000449abb60d
1 2 0.20 844 2294 0x0000000449b087ec
2 2 0.21 850 2294 0x0000000449b35d5d
3 1 0.12 839 2294 0x0000000449b5fd5a
^C
Command mode across ACPI S3:
root@sharkbay:/home/lenb/turbostat-src# ./turbostat -M 0x10 sleep 10
./turbostat: Counter reset detected
14.196299 sec
Signed-off-by: Len Brown <[email protected]>
|
|
The RAPL Joules counter is limited in capacity.
Turbostat estimates how soon it can roll-over
based on the max TDP of the processor --
which tells us the maximum increment rate.
eg.
RAPL: 2759 sec. Joule Counter Range, at 95 Watts
So if a sample duration is longer than 2759 seconds on this system,
'**' replace the decimal place in the display to indicate
that the results may be suspect.
But the display had an extra ' ' in this case, throwing off the columns.
Also, the -J "Joules" option appended an extra "time" column
to the display. While this may be useful, it printed the interval time,
which may not be the accurate time per processor. Remove this column,
which appeared only when using '-J',
as we plan to add accurate per-cpu interval times in a future commit.
Signed-off-by: Len Brown <[email protected]>
|
|
This is a test to verify that
bpf: fix states equal logic for varlen access
actually fixed the problem. The problem was if the register we added to our map
register was UNKNOWN in both the false and true branches and the only thing that
changed was the range then we'd incorrectly assume that the true branch was
valid, which it really wasnt. This tests this case and properly fails without
my fix in place and passes with it in place.
Signed-off-by: Josef Bacik <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Acked-by: Daniel Borkmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Trivial fix to spelling mistake
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: John Stultz <[email protected]>
Cc: Prarit Bhargava <[email protected]>
Cc: Richard Cochran <[email protected]>
Cc: Shuah Khan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
Allow user to specify list of symbols which cause the dump of callchains
to stop at that symbol.
Committer notes:
Testing it:
# perf record -ag usleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 1.177 MB perf.data (33 samples) ]
#
# # Without it:
#
# perf script
swapper 0 [000] 9693.370039: 1 cycles:ppp:
2072ad x86_pmu_enable (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a29d7 perf_pmu_enable.part.90 (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a713a ctx_resched (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a76c1 __perf_event_enable (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a0390 event_function (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a1cff remote_function (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
326978 flush_smp_call_function_queue (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
327413 generic_smp_call_function_single_interrupt (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
249b37 smp_call_function_single_interrupt (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
a04b2c call_function_single_interrupt (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
889427 cpuidle_enter (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
2e534a call_cpuidle (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
2e5730 cpu_startup_entry (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
9f5167 rest_init (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
137ffeb start_kernel ([kernel.vmlinux].init.text)
137f2ca x86_64_start_reservations ([kernel.vmlinux].init.text)
137f419 x86_64_start_kernel ([kernel.vmlinux].init.text)
swapper 0 [000] 9693.370044: 1 cycles:ppp:
20ca1b intel_pmu_handle_irq (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
205b0c perf_event_nmi_handler (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
22a14a nmi_handle (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
22a6b3 default_do_nmi (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
22a83c do_nmi (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
a03fb1 end_repeat_nmi (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a29d7 perf_pmu_enable.part.90 (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a713a ctx_resched (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a76c1 __perf_event_enable (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a0390 event_function (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a1cff remote_function (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
326978 flush_smp_call_function_queue (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
327413 generic_smp_call_function_single_interrupt (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
249b37 smp_call_function_single_interrupt (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
a04b2c call_function_single_interrupt (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
889427 cpuidle_enter (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
2e534a call_cpuidle (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
2e5730 cpu_startup_entry (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
9f5167 rest_init (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
137ffeb start_kernel ([kernel.vmlinux].init.text)
137f2ca x86_64_start_reservations ([kernel.vmlinux].init.text)
#
# # Using it to see just what are the calls from the 'remote_function' function:
#
# perf script --stop-bt remote_function
swapper 0 [000] 9693.370039: 1 cycles:ppp:
2072ad x86_pmu_enable (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a29d7 perf_pmu_enable.part.90 (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a713a ctx_resched (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a76c1 __perf_event_enable (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a0390 event_function (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a1cff remote_function (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
swapper 0 [000] 9693.370044: 1 cycles:ppp:
20ca1b intel_pmu_handle_irq (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
205b0c perf_event_nmi_handler (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
22a14a nmi_handle (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
22a6b3 default_do_nmi (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
22a83c do_nmi (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
a03fb1 end_repeat_nmi (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a29d7 perf_pmu_enable.part.90 (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a713a ctx_resched (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a76c1 __perf_event_enable (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a0390 event_function (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
3a1cff remote_function (/usr/lib/debug/lib/modules/4.8.8-300.fc25.x86_64/vmlinux)
Signed-off-by: David Ahern <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Track freed memory as well as allocations and show the net in the
summary.
Committer notes:
Testing it:
# perf kmem record usleep 1
[ perf record: Woken up 0 times to write data ]
[ perf record: Captured and wrote 1.626 MB perf.data (4208 samples) ]
[root@jouet ~]# perf kmem stat --slab
SUMMARY (SLAB allocator)
========================
Total bytes requested: 234,011
Total bytes allocated: 234,504
Total bytes freed: 213,328 <------
Net total bytes allocated: 21,176
Total bytes wasted on internal fragmentation: 493
Internal fragmentation: 0.210231%
Cross CPU allocations: 4/1,963
#
Signed-off-by: David Ahern <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Having "test" in almost all test descriptions is redundant, simplify it
removing and rewriting tests with such descriptions.
End result:
# perf test
1: vmlinux symtab matches kallsyms : Ok
2: Detect openat syscall event : Ok
3: Detect openat syscall event on all cpus : Ok
4: Read samples using the mmap interface : Ok
5: Parse event definition strings : Ok
6: PERF_RECORD_* events & perf_sample fields : Ok
7: Parse perf pmu format : Ok
8: DSO data read : Ok
9: DSO data cache : Ok
10: DSO data reopen : Ok
11: Roundtrip evsel->name : Ok
12: Parse sched tracepoints fields : Ok
13: syscalls:sys_enter_openat event fields : Ok
14: Setup struct perf_event_attr : Ok
15: Match and link multiple hists : Ok
16: 'import perf' in python : Ok
17: Breakpoint overflow signal handler : Ok
18: Breakpoint overflow sampling : Ok
19: Number of exit events of a simple workload : Ok
20: Software clock events period values : Ok
21: Object code reading : Ok
22: Sample parsing : Ok
23: Use a dummy software event to keep tracking: Ok
24: Parse with no sample_id_all bit set : Ok
25: Filter hist entries : Ok
26: Lookup mmap thread : Ok
27: Share thread mg : Ok
28: Sort output of hist entries : Ok
29: Cumulate child hist entries : Ok
30: Track with sched_switch : Ok
31: Filter fds with revents mask in a fdarray : Ok
32: Add fd to a fdarray, making it autogrow : Ok
33: kmod_path__parse : Ok
34: Thread map : Ok
35: LLVM search and compile :
35.1: Basic BPF llvm compile : Ok
35.2: kbuild searching : Ok
35.3: Compile source for BPF prologue generation: Ok
35.4: Compile source for BPF relocation : Ok
36: Session topology : Ok
37: BPF filter :
37.1: Basic BPF filtering : Ok
37.2: BPF prologue generation : Ok
37.3: BPF relocation checker : Ok
38: Synthesize thread map : Ok
39: Synthesize cpu map : Ok
40: Synthesize stat config : Ok
41: Synthesize stat : Ok
42: Synthesize stat round : Ok
43: Synthesize attr update : Ok
44: Event times : Ok
45: Read backward ring buffer : Ok
46: Print cpu map : Ok
47: Probe SDT events : Ok
48: is_printable_array : Ok
49: Print bitmap : Ok
50: perf hooks : Ok
51: x86 rdpmc : Ok
52: Convert perf time to TSC : Ok
53: DWARF unwind : Ok
54: x86 instruction decoder - new instructions : Ok
55: Intel cqm nmi context read : Skip
#
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Perf hooks allow hooking user code at perf events. They can be used for
manipulation of BPF maps, taking snapshot and reporting results. In this
patch two perf hook points are introduced: record_start and record_end.
To avoid buggy user actions, a SIGSEGV signal handler is introduced into
'perf record'. It turns off perf hook if it causes a segfault and report
an error to help debugging.
A test case for perf hook is introduced.
Test result:
$ ./buildperf/perf test -v hook
50: Test perf hooks :
--- start ---
test child forked, pid 10311
SIGSEGV is observed as expected, try to recover.
Fatal error (SEGFAULT) in perf hook 'test'
test child finished with 0
---- end ----
Test perf hooks: Ok
Signed-off-by: Wang Nan <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Joe Stringer <[email protected]>
Cc: Zefan Li <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Add a new API to libbpf, caller is able to get bpf_map through the
offset of bpf_map_def to 'maps' section.
The API will be used to help jitted perf hook code find fd of a map.
Signed-off-by: Wang Nan <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Joe Stringer <[email protected]>
Cc: Zefan Li <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Similar to other classes defined in libbpf.h (map and program), allow
'object' class has its own private data.
Signed-off-by: Wang Nan <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Joe Stringer <[email protected]>
Cc: Zefan Li <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Add more BPF map operations to libbpf. Also add bpf_obj_{pin,get}(). They
can be used on not only BPF maps but also BPF programs.
Signed-off-by: Wang Nan <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Joe Stringer <[email protected]>
Cc: Zefan Li <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
1) The test_lru_map and test_lru_dist fails building on my machine since
the sys/resource.h header is not included.
2) test_verifier fails in one test case where we try to call an invalid
function, since the verifier log output changed wrt printing function
names.
3) Current selftest suite code relies on sysconf(_SC_NPROCESSORS_CONF) for
retrieving the number of possible CPUs. This is broken at least in our
scenario and really just doesn't work.
glibc tries a number of things for retrieving _SC_NPROCESSORS_CONF.
First it tries equivalent of /sys/devices/system/cpu/cpu[0-9]* | wc -l,
if that fails, depending on the config, it either tries to count CPUs
in /proc/cpuinfo, or returns the _SC_NPROCESSORS_ONLN value instead.
If /proc/cpuinfo has some issue, it returns just 1 worst case. This
oddity is nothing new [1], but semantics/behaviour seems to be settled.
_SC_NPROCESSORS_ONLN will parse /sys/devices/system/cpu/online, if
that fails it looks into /proc/stat for cpuX entries, and if also that
fails for some reason, /proc/cpuinfo is consulted (and returning 1 if
unlikely all breaks down).
While that might match num_possible_cpus() from the kernel in some
cases, it's really not guaranteed with CPU hotplugging, and can result
in a buffer overflow since the array in user space could have too few
number of slots, and on perpcu map lookup, the kernel will write beyond
that memory of the value buffer.
William Tu reported such mismatches:
[...] The fact that sysconf(_SC_NPROCESSORS_CONF) != num_possible_cpu()
happens when CPU hotadd is enabled. For example, in Fusion when
setting vcpu.hotadd = "TRUE" or in KVM, setting ./qemu-system-x86_64
-smp 2, maxcpus=4 ... the num_possible_cpu() will be 4 and sysconf()
will be 2 [2]. [...]
Documentation/cputopology.txt says /sys/devices/system/cpu/possible
outputs cpu_possible_mask. That is the same as in num_possible_cpus(),
so first step would be to fix the _SC_NPROCESSORS_CONF calls with our
own implementation. Later, we could add support to bpf(2) for passing
a mask via CPU_SET(3), for example, to just select a subset of CPUs.
BPF samples code needs this fix as well (at least so that people stop
copying this). Thus, define bpf_num_possible_cpus() once in selftests
and import it from there for the sample code to avoid duplicating it.
The remaining sysconf(_SC_NPROCESSORS_CONF) in samples are unrelated.
After all three issues are fixed, the test suite runs fine again:
# make run_tests | grep self
selftests: test_verifier [PASS]
selftests: test_maps [PASS]
selftests: test_lru_map [PASS]
selftests: test_kmod.sh [PASS]
[1] https://www.sourceware.org/ml/libc-alpha/2011-06/msg00079.html
[2] https://www.mail-archive.com/[email protected]/msg121183.html
Fixes: 3059303f59cf ("samples/bpf: update tracex[23] examples to use per-cpu maps")
Fixes: 86af8b4191d2 ("Add sample for adding simple drop program to link")
Fixes: df570f577231 ("samples/bpf: unit test for BPF_MAP_TYPE_PERCPU_ARRAY")
Fixes: e15596717948 ("samples/bpf: unit test for BPF_MAP_TYPE_PERCPU_HASH")
Fixes: ebb676daa1a3 ("bpf: Print function name in addition to function id")
Fixes: 5db58faf989f ("bpf: Add tests for the LRU bpf_htab")
Signed-off-by: Daniel Borkmann <[email protected]>
Cc: William Tu <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Leverage pid/tid filtering done by symbol_conf hooks.
Signed-off-by: David Ahern <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Add handlers for sched:sched_migrate_task event. Total number of
migrations is added to summary display and -M/--migrations can be used
to show migration events.
Signed-off-by: David Ahern <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Namhyung Kim <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
To help in debugging when the wrong offset is being used, like in:
│13d98: ↓ jne 13dd1 <lzma_lzma_preset@@XZ_5.0+0x28e1>
That is the full line from objdump, and it seems what should be used is
13dd1, not 28e1.
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
To print some values, like in the annotation code with invalid jump
offsets.
Cc: Adrian Hunter <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
It is not correct to assimilate the elf data of the maps section to an
array of map definition. In fact the sizes differ. The offset provided
in the symbol section has to be used instead.
This patch fixes a bug causing a elf with two maps not to load
correctly.
Wang Nan added:
This patch requires a name for each BPF map, so array of BPF maps is not
allowed. This restriction is reasonable, because kernel verifier forbid
indexing BPF map from such array unless the index is a fixed value, but
if the index is fixed why not merging it into name?
For example:
Program like this:
...
unsigned long cpu = get_smp_processor_id();
int *pval = map_lookup_elem(&map_array[cpu], &key);
...
Generates bytecode like this:
0: (b7) r1 = 0
1: (63) *(u32 *)(r10 -4) = r1
2: (b7) r1 = 680997
3: (63) *(u32 *)(r10 -8) = r1
4: (85) call 8
5: (67) r0 <<= 4
6: (18) r1 = 0x112dd000
8: (0f) r0 += r1
9: (bf) r2 = r10
10: (07) r2 += -4
11: (bf) r1 = r0
12: (85) call 1
Where instruction 8 is the computation, 8 and 11 render r1 to an invalid
value for function map_lookup_elem, causes verifier report error.
Signed-off-by: Eric Leblond <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Wang Nan <[email protected]>
[ Merge bpf_object__init_maps_name into bpf_object__init_maps.
Fix segfault for buggy BPF script Validate obj->maps ]
Cc: Zefan Li <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Wang Nan <[email protected]>
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Commit 0b3c2264ae30 ("perf symbols: Fix kallsyms perf test on ppc64le")
refers struct symbol in probe_event.h, but forgets to include its
definition. Gcc will complain about it when that definition is not
added, by sheer luck, by some other header included before
probe_event.h.
Signed-off-by: Wang Nan <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Naveen N. Rao <[email protected]>
Cc: Zefan Li <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Before this patch perf panics if kptr_restrict is set to 1 and perf is
owned by root with suid set:
$ whoami
wangnan
$ ls -l ./perf
-rwsr-xr-x 1 root root 19781908 Sep 21 19:29 /home/wangnan/perf
$ cat /proc/sys/kernel/kptr_restrict
1
$ cat /proc/sys/kernel/perf_event_paranoid
-1
$ ./perf record -a
Segmentation fault (core dumped)
$
The reason is that perf assumes it is allowed to read kptr from
/proc/kallsyms when euid is root, but in fact the kernel doesn't allow
reading kptr when euid and uid do not match with each other:
$ cp /bin/cat .
$ sudo chown root:root ./cat
$ sudo chmod u+s ./cat
$ cat /proc/kallsyms | grep do_fork
0000000000000000 T _do_fork <--- kptr is hidden even euid is root
$ sudo cat /proc/kallsyms | grep do_fork
ffffffff81080230 T _do_fork
See lib/vsprintf.c for kernel side code.
This patch fixes this problem by checking both uid and euid.
Signed-off-by: Wang Nan <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Zefan Li <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
On ubuntu the internal kernel version code is different from what can
be retrived from uname:
$ uname -r
4.4.0-47-generic
$ cat /lib/modules/`uname -r`/build/include/generated/uapi/linux/version.h
#define LINUX_VERSION_CODE 263192
#define KERNEL_VERSION(a,b,c) (((a) << 16) + ((b) << 8) + (c))
$ cat /lib/modules/`uname -r`/build/include/generated/utsrelease.h
#define UTS_RELEASE "4.4.0-47-generic"
#define UTS_UBUNTU_RELEASE_ABI 47
$ cat /proc/version_signature
Ubuntu 4.4.0-47.68-generic 4.4.24
The macro LINUX_VERSION_CODE is set to 4.4.24 (263192 == 0x40418), but
`uname -r` reports 4.4.0.
This mismatch causes LINUX_VERSION_CODE macro passed to BPF script become
an incorrect value, results in magic failure in BPF loading:
$ sudo ./buildperf/perf record -e ./tools/perf/tests/bpf-script-example.c ls
event syntax error: './tools/perf/tests/bpf-script-example.c'
\___ Failed to load program for unknown reason
According to Ubuntu document (https://wiki.ubuntu.com/Kernel/FAQ), the
correct kernel version can be retrived through /proc/version_signature, which
is ubuntu specific.
This patch checks the existance of /proc/version_signature, and returns
version number through parsing this file instead of uname. Version string
is untouched (value returns from uname) because `uname -r` is required
to be consistence with path of kbuild directory in /lib/module.
Signed-off-by: Wang Nan <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Zefan Li <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
When it records callchains, they will always have 2 scheduler functions
(__schedule + schedule or __schedule + preempt_schedule) and get
ignored. So it should collect 2 more functions to show the expected
number of callchains to user.
Committer Notes:
Example of final result, using the same perf.data file as in the
previous cset comment, but this time redirecting the output of 'perf
sched timehist' to a file instead of copy'n'pasting from xterm:
[root@jouet experimental]# perf sched timehist > /tmp/bla
[root@jouet experimental]# cat /tmp/bla
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
-------- ---- -------------------- ------ ------ -----
6.494998 [01] <idle> 0.000 0.000 0.000
6.495027 [02] perf[519] 0.000 0.000 0.000 schedule_hrtimeout_range_clock <- schedule_hrtimeout_range <- poll_schedule_timeout <- do_sys_poll <- sys_poll
6.495096 [03] <idle> 0.000 0.000 0.000
6.495100 [03] rcuos/0[9] 0.000 0.005 0.003 rcu_nocb_kthread <- kthread <- ret_from_fork
6.495113 [01] perf[520] 0.000 0.008 0.114 preempt_schedule_common <- _cond_resched <- wait_for_completion <- stop_one_cpu <- sched_exec <- do_execveat_common.isra.35
6.495121 [00] <idle> 0.000 0.000 0.000
6.495129 [01] migration/1[17] 0.000 0.003 0.016 smpboot_thread_fn <- kthread <- ret_from_fork
6.496085 [02] <idle> 0.000 0.000 1.057
6.496096 [02] kworker/u16:1[31169] 0.000 0.004 0.011 worker_thread <- kthread <- ret_from_fork
6.496096 [03] <idle> 0.003 0.000 0.996
6.496169 [02] <idle> 0.011 0.000 0.072
6.496171 [00] ls[520] 0.008 0.000 1.049 do_exit <- do_group_exit <- [unknown] <- entry_SYSCALL_64_fastpath
6.496172 [03] gnome-terminal-[4391] 0.000 0.003 0.076 schedule_hrtimeout_range_clock <- schedule_hrtimeout_range <- poll_schedule_timeout <- do_sys_poll <- sys_poll
Signed-off-by: Namhyung Kim <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The sched_switch event always captured from the scheduler function. So
it'd be great omit them from the callchain. This patch marks the
functions to be omitted by later patch.
Committer notes:
Testing it:
Before:
[root@jouet experimental]# perf sched record -g ls
Dockerfile perf.data x-mips64
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 1.355 MB perf.data (29 samples) ]
[root@jouet experimental]# perf sched timehist
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
----------- ----- ----------------- ------ ------ ------
6.494998 [001] <idle> 0.000 0.000 0.000
6.495027 [002] perf[519] 0.000 0.000 0.000 __schedule <- schedule <- schedule_hrtimeout_range_clock <- schedule_hrtimeou
6.495096 [003] <idle> 0.000 0.000 0.000
6.495100 [003] rcuos/0[9] 0.000 0.005 0.003 __schedule <- schedule <- rcu_nocb_kthread <- kthread <- ret_from_fork
6.495113 [001] perf[520] 0.000 0.008 0.114 __schedule <- preempt_schedule_common <- _cond_resched <- wait_for_completion
6.495121 [000] <idle> 0.000 0.000 0.000
6.495129 [001] migration/1[17] 0.000 0.003 0.016 __schedule <- schedule <- smpboot_thread_fn <- kthread <- ret_from_fork
6.496085 [002] <idle> 0.000 0.000 1.057
6.496096 [002] kworker/u16:1[31169] 0.000 0.004 0.011 __schedule <- schedule <- worker_thread <- kthread <- ret_from_fork
6.496096 [003] <idle> 0.003 0.000 0.996
6.496169 [002] <idle> 0.011 0.000 0.072
6.496171 [000] ls[520] 0.008 0.000 1.049 __schedule <- schedule <- do_exit <- do_group_exit <- [unknown]
6.496172 [003] gnome-terminal-[4391] 0.000 0.003 0.076 __schedule <- schedule <- schedule_hrtimeout_range_clock <- schedule_hrtimeo
After:
[root@jouet experimental]# perf sched timehist
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
----------- ----- ----------------- ----- ----- ------
6.494998 [001] <idle> 0.000 0.000 0.000
6.495027 [002] perf[519] 0.000 0.000 0.000 schedule_hrtimeout_range_clock <- schedule_hrtimeout_range <- poll_schedule_t
6.495096 [003] <idle> 0.000 0.000 0.000
6.495100 [003] rcuos/0[9] 0.000 0.005 0.003 rcu_nocb_kthread <- kthread <- ret_from_fork
6.495113 [001] perf[520] 0.000 0.008 0.114 preempt_schedule_common <- _cond_resched <- wait_for_completion <- stop_one_c
6.495121 [000] <idle> 0.000 0.000 0.000
6.495129 [001] migration/1[17] 0.000 0.003 0.016 smpboot_thread_fn <- kthread <- ret_from_fork
6.496085 [002] <idle> 0.000 0.000 1.057
6.496096 [002] kworker/u16:1[31169] 0.000 0.004 0.011 worker_thread <- kthread <- ret_from_fork
6.496096 [003] <idle> 0.003 0.000 0.996
6.496169 [002] <idle> 0.011 0.000 0.072
6.496171 [000] ls[520] 0.008 0.000 1.049 do_exit <- do_group_exit <- [unknown]
6.496172 [003] gnome-terminal-[4391] 0.000 0.003 0.076 schedule_hrtimeout_range_clock <- schedule_hrtimeout_range <- poll_schedule_
[root@jouet experimental]#
Signed-off-by: Namhyung Kim <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
For tracepoint events, callchains always contain certain functions.
Sometimes it'd be better to skip those functions as they have no value.
Signed-off-by: Namhyung Kim <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Support the PowerPC architecture using the ins_ops association
method.
Committer notes:
Testing it with a perf.data file collected on a PowerPC machine and
cross-annotated on a x86_64 workstation, using the associated vmlinux
file:
$ perf report -i perf.data.f22vm.powerdev --vmlinux vmlinux.powerpc
.ktime_get vmlinux.powerpc
│ clrldi r9,r28,63
8.57 │ ┌──bne e0 <- TUI cursor positioned here
│54:│ lwsync
2.86 │ │ std r2,40(r1)
│ │ ld r9,144(r31)
│ │ ld r3,136(r31)
│ │ ld r30,184(r31)
│ │ ld r10,0(r9)
│ │ mtctr r10
│ │ ld r2,8(r9)
8.57 │ │→ bctrl
│ │ ld r2,40(r1)
│ │ ld r10,160(r31)
│ │ ld r5,152(r31)
│ │ lwz r7,168(r31)
│ │ ld r9,176(r31)
8.57 │ │ lwz r6,172(r31)
│ │ lwsync
2.86 │ │ lwz r8,128(r31)
│ │ cmpw cr7,r8,r28
2.86 │ │↑ bne 48
│ │ subf r10,r10,r3
│ │ mr r3,r29
│ │ and r10,r10,r5
2.86 │ │ mulld r10,r10,r7
│ │ add r9,r10,r9
│ │ srd r9,r9,r6
│ │ add r9,r9,r30
│ │ std r9,0(r29)
│ │ addi r1,r1,144
│ │ ld r0,16(r1)
│ │ ld r28,-32(r1)
│ │ ld r29,-24(r1)
│ │ ld r30,-16(r1)
│ │ mtlr r0
│ │ ld r31,-8(r1)
│ │← blr
5.71 │e0:└─→mr r1,r1
11.43 │ mr r2,r2
11.43 │ lwz r28,128(r31)
Press 'h' for help on key bindings
$ perf report -i perf.data.f22vm.powerdev --header-only
# ========
# captured on: Thu Nov 24 12:40:38 2016
# hostname : pdev-f22-qemu
# os release : 4.4.10-200.fc22.ppc64
# perf version : 4.9.rc1.g6298ce
# arch : ppc64
# nrcpus online : 48
# nrcpus avail : 48
# cpudesc : POWER7 (architected), altivec supported
# cpuid : 74,513
# total memory : 4158976 kB
# cmdline : /home/ravi/Workspace/linux/tools/perf/perf record -a
# event : name = cycles:ppp, , size = 112, { sample_period, sample_freq } = 4000, sample_type = IP|TID|TIME|CPU|PERIOD, disabled = 1, inherit = 1, mmap = 1, comm = 1, freq = 1, task = 1, precise_ip = 3, sample_id_all = 1, exclude_guest = 1, mmap2 = 1, comm_exec = 1
# HEADER_CPU_TOPOLOGY info available, use -I to display
# HEADER_NUMA_TOPOLOGY info available, use -I to display
# pmu mappings: cpu = 4, software = 1, tracepoint = 2, breakpoint = 5
# missing features: HEADER_TRACING_DATA HEADER_BRANCH_STACK HEADER_GROUP_DESC HEADER_AUXTRACE HEADER_STAT HEADER_CACHE
# ========
#
$
Signed-off-by: Ravi Bangoria <[email protected]>
Signed-off-by: Naveen N. Rao <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Kim Phillips <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
By using arch->init() to set up some regular expressions to associate
ins_ops to ARM instructions, ditching that old table that has
instructions not present on ARM.
Take advantage of having an arch->init() to hide more arm specific stuff
from the common code, like the objdump details.
The regular expressions comes from a patch written by Kim Phillips.
Reviewed-by: Ravi Bangoria <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Chris Riyder <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Kim Phillips <[email protected]>
Cc: Markus Trippelsdorf <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Naveen N. Rao <[email protected]>
Cc: Pawel Moll <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Russell King <[email protected]>
Cc: Taeung Song <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Arches like ARM will want to use regular expressions when deciding what
instructions to associate with what ins_ops, provide infrastructure for
that.
Reviewed-by: Ravi Bangoria <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Chris Riyder <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Kim Phillips <[email protected]>
Cc: Markus Trippelsdorf <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Naveen N. Rao <[email protected]>
Cc: Pawel Moll <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Russell King <[email protected]>
Cc: Taeung Song <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Some arches may want to dynamically populate the table using regular
expressions on the instruction names to associate them with a set of
parsing/formatting/etc functions (struct ins_ops), so provide a fallback
for when the ins__find() method fails.
That fall back will be able to resize the arch->instructions, setting
arch->nr_instructions appropriately, helper functions to associate an
ins_ops to an instruction name, growing the arch->instructions if needed
and resorting it are provided, all the arch specific callback needs to
do is to decide if the missing instruction should be added to
arch->instructions with a ins_ops association.
Reviewed-by: Ravi Bangoria <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Chris Riyder <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Kim Phillips <[email protected]>
Cc: Markus Trippelsdorf <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Naveen N. Rao <[email protected]>
Cc: Pawel Moll <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Russell King <[email protected]>
Cc: Taeung Song <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The disasm_line::name field is always equal to ins::name, being used
just to locate the instruction's ins_ops from the per-arch instructions
table.
Eliminate this duplication, nuking that field and instead make
ins__find() return an ins_ops, store it in disasm_line::ins.ops, and
keep just in disasm_line::ins.name what was in disasm_line::name, this
way we end up not keeping a reference to entries in the per-arch
instructions table.
This in turn will help supporting multiple ways to manage the per-arch
instructions table, allowing resorting that array, for instance, when
the entries will move after references to its addresses were made. The
same problem is avoided when one grows the array with realloc.
So architectures simply keeping a constant array will work as well as
architectures building the table using regular expressions or other
logic that involves resorting the table.
Reviewed-by: Ravi Bangoria <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Chris Riyder <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Kim Phillips <[email protected]>
Cc: Markus Trippelsdorf <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Naveen N. Rao <[email protected]>
Cc: Pawel Moll <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Russell King <[email protected]>
Cc: Taeung Song <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
New tool:
- 'perf sched timehist' provides an analysis of scheduling events.
Example usage:
perf sched record -- sleep 1
perf sched timehist
By default it shows the individual schedule events, including the wait
time (time between sched-out and next sched-in events for the task), the
task scheduling delay (time between wakeup and actually running) and run
time for the task:
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
-------- ------ ---------------- --------- --------- --------
1.874569 [0011] gcc[31949] 0.014 0.000 1.148
1.874591 [0010] gcc[31951] 0.000 0.000 0.024
1.874603 [0010] migration/10[59] 3.350 0.004 0.011
1.874604 [0011] <idle> 1.148 0.000 0.035
1.874723 [0005] <idle> 0.016 0.000 1.383
1.874746 [0005] gcc[31949] 0.153 0.078 0.022
...
Times are in msec.usec. (David Ahern, Namhyung Kim)
Improvements:
- Make 'perf c2c report' support -f/--force, to allow skipping the
ownership check for root users, for instance, just like the other
tools (Jiri Olsa)
- Allow sorting cachelines by total number of HITMs, in addition to
local and remote numbers (Jiri Olsa)
Fixes:
- Make sure errors aren't suppressed by the TUI reset at the end of
a 'perf c2c report' session (Jiri Olsa)
Infrastructure changes:
- Initial work on having the annotate code better support multiple
architectures, including the ability to cross-annotate, i.e. to
annotate perf.data files collected on an ARM system on a x86_64
workstation (Arnaldo Carvalho de Melo, Ravi Bangoria, Kim Phillips)
- Use USECS_PER_SEC instead of hard coded number in libtraceevent (Steven Rostedt)
- Add retrieval of preempt count and latency flags in libtraceevent (Steven Rostedt)
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Signed-off-by: Ingo Molnar <[email protected]>
|
|
The -V option provides a visual aid for sched switches by cpu:
$ perf sched timehist -V
time cpu 0123456789abc task name b/n time sch delay run time
[tid/pid] (msec) (msec) (msec)
--------------- ------ ------------- -------------------- --------- --------- ---------
...
2412598.429696 [0009] i <idle> 0.000 0.000 0.000
2412598.429767 [0002] s perf[7219] 0.000 0.000 0.000
2412598.429783 [0009] s perf[7220] 0.000 0.006 0.087
2412598.429794 [0010] i <idle> 0.000 0.000 0.000
2412598.429795 [0009] s migration/9[53] 0.000 0.003 0.011
2412598.430370 [0010] s sleep[7220] 0.011 0.000 0.576
2412598.432584 [0003] i <idle> 0.000 0.000 0.000
...
Committer notes:
'i' marks idle time, 's' are scheduler events.
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: Namhyung Kim <[email protected]>
Acked-by: Ingo Molnar <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
[ Add documentation based on above commit message ]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
If callchains were recorded they are appended to the line with a default stack depth of 5:
1.874569 [0011] gcc[31949] 0.014 0.000 1.148 wait_for_completion_killable <- do_fork <- sys_vfork <- stub_vfork <- __vfork
1.874591 [0010] gcc[31951] 0.000 0.000 0.024 __cond_resched <- _cond_resched <- wait_for_completion <- stop_one_cpu <- sched_exec
1.874603 [0010] migration/10[59] 3.350 0.004 0.011 smpboot_thread_fn <- kthread <- ret_from_fork
1.874604 [0011] <idle> 1.148 0.000 0.035 cpu_startup_entry <- start_secondary
1.874723 [0005] <idle> 0.016 0.000 1.383 cpu_startup_entry <- start_secondary
1.874746 [0005] gcc[31949] 0.153 0.078 0.022 do_wait sys_wait4 <- system_call_fastpath <- __GI___waitpid
--no-call-graph can be used to not show the callchains. --max-stack is used
to control the number of frames shown (default of 5). -x/--excl options can
be used to collapse redundant callchains to get more relevant data on screen.
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: Namhyung Kim <[email protected]>
Acked-by: Ingo Molnar <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
[ Add documentation based on above commit message ]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The -w option is to show wakeup events with timehist.
$ perf sched timehist -w
time cpu task name b/n time sch delay run time
[tid/pid] (msec) (msec) (msec)
--------------- ------ -------------------- --------- --------- ---------
2412598.429689 [0002] perf[7219] awakened: perf[7220]
2412598.429696 [0009] <idle> 0.000 0.000 0.000
2412598.429767 [0002] perf[7219] 0.000 0.000 0.000
2412598.429780 [0009] perf[7220] awakened: migration/9[53]
...
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: Namhyung Kim <[email protected]>
Acked-by: Ingo Molnar <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
[ Add documentation based on above commit message ]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The -s/--summary option is to show process runtime statistics. And the
-S/--with-summary option is to show the stats with the normal output.
$ perf sched timehist -s
Runtime summary
comm parent sched-in run-time min-run avg-run max-run stddev
(count) (msec) (msec) (msec) (msec) %
---------------------------------------------------------------------------------------------------------
ksoftirqd/0[3] 2 2 0.011 0.004 0.005 0.006 14.87
rcu_preempt[7] 2 11 0.071 0.002 0.006 0.017 20.23
watchdog/0[11] 2 1 0.002 0.002 0.002 0.002 0.00
watchdog/1[12] 2 1 0.004 0.004 0.004 0.004 0.00
...
Terminated tasks:
sleep[7220] 7219 3 0.770 0.087 0.256 0.576 62.28
Idle stats:
CPU 0 idle for 2352.006 msec
CPU 1 idle for 2764.497 msec
CPU 2 idle for 2998.229 msec
CPU 3 idle for 2967.800 msec
Total number of unique tasks: 52
Total number of context switches: 2532
Total run time (msec): 218.036
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: Namhyung Kim <[email protected]>
Acked-by: Ingo Molnar <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
[ Add documentation from last commit, so that docs comes with the cset that introduces the feature ]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
'perf sched timehist' provides an analysis of scheduling events.
Example usage:
perf sched record -- sleep 1
perf sched timehist
By default it shows the individual schedule events, including the wait
time (time between sched-out and next sched-in events for the task), the
task scheduling delay (time between wakeup and actually running) and run
time for the task:
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
-------------- ------ -------------------- --------- --------- ---------
79371.874569 [0011] gcc[31949] 0.014 0.000 1.148
79371.874591 [0010] gcc[31951] 0.000 0.000 0.024
79371.874603 [0010] migration/10[59] 3.350 0.004 0.011
79371.874604 [0011] <idle> 1.148 0.000 0.035
79371.874723 [0005] <idle> 0.016 0.000 1.383
79371.874746 [0005] gcc[31949] 0.153 0.078 0.022
...
Times are in msec.usec.
Committer note:
Add above explanation as the 'perf sched timehist' entry for 'man
perf-sched'.
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: Namhyung Kim <[email protected]>
Acked-by: Ingo Molnar <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The EVSEL__PRINT_CALLCHAIN_ARROW options can be used to print callchains
with arrows for readability. It will be used 'sched timehist' command
like below:
__schedule <- schedule <- schedule_timeout <- rcu_gp_kthread <- kthread <- ret_from_fork
__schedule <- schedule <- schedule_timeout <- rcu_gp_kthread <- kthread <- ret_from_fork
__schedule <- schedule <- worker_thread <- kthread <- ret_from_fork
Suggested-and-Acked-by: Ingo Molnar <[email protected]>
Signed-off-by: Namhyung Kim <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The __symbol__fprintf_symname_offs() always shows symbol offsets. So
there's no difference between 'perf script -F ip,sym' and 'perf script
-F ip,sym,symoff'. I don't think it's a desired behavior..
Signed-off-by: Namhyung Kim <[email protected]>
Acked-by: Ingo Molnar <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Adding support for cascading options added by Namhyung in:
commit 369a2478973a ("tools lib subcmd: Support cascading options")
This way the report and record command share options with with c2c
command and can save some option duplicates. For now it's the 'v'
option.
Signed-off-by: Jiri Olsa <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Don Zickus <[email protected]>
Cc: Joe Mario <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Currently we display the cacheline list sorted on remote HITMs by
default.
The problem is that they might not be always counted and 'perf c2c
report' displays an empty output. Thus it's more convenient to display
and sort the cacheline list based on the total of HITMs and have the
best change to see data in the default report run.
Signed-off-by: Jiri Olsa <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Don Zickus <[email protected]>
Cc: Joe Mario <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Count total number of HITMs in a special field. This will ease up
addition of total HITM sorting into c2c report in the following patch.
Signed-off-by: Jiri Olsa <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Don Zickus <[email protected]>
Cc: Joe Mario <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Adding -f/--force option to go through ownership validation:
$ sudo perf c2c report
File perf.data not owned by current user or root (use -f to override)
$
$ sudo perf c2c report -f
< c2c report output >
$
Signed-off-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Don Zickus <[email protected]>
Cc: Joe Mario <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Because of the early browser switch we won't get possible error
messages, as it will clear the screen right after showing the message,
e.g.:
Before:
$ sudo perf c2c report -d lcl
$
After:
$ sudo perf c2c report -d lcl
File perf.data not owned by current user or root (use -f to override)
$
$ ls -la perf.data
-rw-------. 1 acme acme 26648 Nov 22 15:11 perf.data
$
Signed-off-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Don Zickus <[email protected]>
Cc: Joe Mario <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
It is useful for debug to see file descriptors for each event.
Before:
$ perf stat -vvv -e cycles,cache-misses ls
...
sys_perf_event_open: pid 12146 cpu -1 group_fd -1 flags 0x8
...
sys_perf_event_open: pid 12146 cpu -1 group_fd 3 flags 0x8
sys_perf_event_open failed, error -13
Now:
$ perf stat -vvv -e cycles,cache-misses ls
...
sys_perf_event_open: pid 12858 cpu -1 group_fd -1 flags 0x8 = 3
...
sys_perf_event_open: pid 12858 cpu -1 group_fd 3 flags 0x8
sys_perf_event_open failed, error -13
Signed-off-by: Jiri Olsa <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Don Zickus <[email protected]>
Cc: Joe Mario <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Add a way to retrieve the preempt count as well as the latency flags from a
pevent_record.
int pevent_data_preempt_count(pevent, record);
returns the preempt count of a record.
int pevent_data_flags(pevent, record);
returns the latency flags for a record.
Signed-off-by: Steven Rostedt <[email protected]>
Acked-by: Namhyung Kim <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Jiri Olsa <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Instead of using 1000000, use the define in time64.h instead.
Also remove the the duplicate defines for NSECS_PER_SEC.
Signed-off-by: Steven Rostedt <[email protected]>
Acked-by: Namhyung Kim <[email protected]>
Cc: Andrew Morton <[email protected]>
Cc: Jiri Olsa <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into core/rcu
Pull RCU updates from Paul E. McKenney:
- Documentation updates, yet again just simple changes.
- Miscellaneous fixes, including a change to call_rcu()'s
rcu_head alignment check.
- Security-motivated list consistency checks, which are
disabled by default behind DEBUG_LIST.
- Torture-test updates.
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Conflicts:
arch/x86/kernel/fpu/core.c
Signed-off-by: Ingo Molnar <[email protected]>
|