| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Len Brown <[email protected]>
|
|
Most CPUs do not have a hardware c1 counter,
and so turbostat derives c1 residency:
c1 = TSC - MPERF - other_core_cstate_counters
As it is not possible to atomically read these coutners,
measurement jitter can case this calcuation to "go negative"
when very close to 0. Turbostat detect that case and
simply prints c1 = 0.00%
But that check neglected to account for systems where the TSC
crystal clock domain and the MPERF BCLK domain are differ by
a small amount. That allowed very small negative c1 numbers
to escape this check and be printed as huge positve numbers.
This code begs for a bit of cleanup, but this patch
is the minimal change to fix the issue.
Signed-off-by: Len Brown <[email protected]>
|
|
Add GFX%rc6 and GFXMHz to the column descriptions section
of the turbostat man page.
Signed-off-by: Doug Smythies <[email protected]>
Signed-off-by: Len Brown <[email protected]>
|
|
Syntax only.
The HWP CAPABILTIES and REQUEST ratios are more easily
viewed in decimal -- just multiply by 100 and you get MHz...
new:
cpu0: MSR_HWP_CAPABILITIES: 0x010c1b23 (high 35 guar 27 eff 12 low 1)
cpu0: MSR_HWP_REQUEST: 0x80002301 (min 1 max 35 des 0 epp 0x80 window 0x0 pkg 0x0)
old:
cpu0: MSR_HWP_CAPABILITIES: 0x010c1b23 (high 0x23 guar 0x1b eff 0xc low 0x1)
cpu0: MSR_HWP_REQUEST: 0x80002301 (min 0x1 max 0x23 des 0x0 epp 0x80 window 0x0 pkg 0x0)
Signed-off-by: Len Brown <[email protected]>
|
|
cpu0: MSR_IA32_TEMPERATURE_TARGET: 0x00641400 (100 C)
cpu0: MSR_IA32_PACKAGE_THERM_STATUS: 0x884b0800 (25 C)
cpu0: MSR_IA32_PACKAGE_THERM_INTERRUPT: 0x00000003 (100 C, 100 C)
Enable the same per-core output, but hide it behind --debug
because it is too verbose on big systems.
Signed-off-by: Len Brown <[email protected]>
|
|
While the current SDM is silent on the matter, the Core and GFX
RAPL power meters on SKL and KBL appear to work -- so show them.
Reported-by: Yaroslav Isakov <[email protected]>
Signed-off-by: Len Brown <[email protected]>
|
|
( This is a rebased version of https://lkml.org/lkml/2017/2/7/662 )
Python's CC and link Makefile variables were not passed to feature
detection, causing feature detection to use system's Python rather than
PYTHON_CONFIG's one. This created a mismatch between the detected Python
support and the one actually used by perf when PYTHON_CONFIG is
specified.
Fix it by moving Python's variable initialization to before feature
detection and pass FLAGS_PYTHON_EMBED to Python's feature detection's
build target.
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The check between the hardware state and our shadow of it is
checked in the signal handler for all bounds exceptions,
even for the ones where we don't keep the shadow up2date.
This is a problem because when no shadow is kept the handler
fails at this point and hides the real reason of the
exception.
Move the check into the code-path evaluating normal bounds
exceptions to prevent this.
Signed-off-by: Joerg Roedel <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: Dave Hansen <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Shuah Khan <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull 'perf annotate' fix for s390:
- The move to support cross arch annotation introduced per arch
initialization requirements, fullfill them for s/390 (Christian Borntraeger)
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
|
|
When parsing disassemble lines for source line number, use a stripped
line instead of raw line.
Signed-off-by: Taeung Song <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
When parsing disassemble lines, use ltrim() and rtrim() to strip them,
not using just while loop and isspace().
Signed-off-by: Taeung Song <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Pipe-mode has no perf.data header, hence no upfront knowledge of presend
and missing features, hence, do not print missing features in pipe-mode.
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Session sets a number parameters that rely on evlist. These parameters
are not used in pipe-mode and should not be set, since evlist is
unavailable. Fix that.
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
[ Check if file != NULL in perf_session__new(), like when used by builtin-top.c ]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
perf annotate did not get some love for pipe-mode, and did not have
.attr and .buil_id setup (while record and inject did. Fix that.
It can easily be reproduced by:
perf record -o - noploop | perf annotate
that in my system shows:
0xd8 [0x28]: failed to process type: 9
Committer Testing:
Before:
$ perf record -o - stress -t 2 -c 2 | perf annotate --stdio
stress: info: [11060] dispatching hogs: 2 cpu, 0 io, 0 vm, 0 hdd
0x4470 [0x28]: failed to process type: 9
$ stress: info: [11060] successful run completed in 2s
$
After:
$ perf record -o - stress -t 2 -c 2 | perf annotate --stdio
stress: info: [11871] dispatching hogs: 2 cpu, 0 io, 0 vm, 0 hdd
stress: info: [11871] successful run completed in 2s
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
no symbols found in /usr/bin/stress, maybe install a debug package?
Percent | Source code & Disassembly of libc-2.24.so for cycles:uhH (6117 samples)
---------------------------------------------------------------------------------------
:
: Disassembly of section .text:
:
: 000000000003b050 <random_r>:
: __random_r():
10.56 : 3b050: test %rdi,%rdi
0.00 : 3b053: je 3b0d0 <random_r+0x80>
0.34 : 3b055: test %rsi,%rsi
0.00 : 3b058: je 3b0d0 <random_r+0x80>
0.46 : 3b05a: mov 0x18(%rdi),%eax
12.44 : 3b05d: mov 0x10(%rdi),%r8
0.18 : 3b061: test %eax,%eax
0.00 : 3b063: je 3b0b0 <random_r+0x60>
<SNIP>
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Add a minimal description of pipe's data format.
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
__perf_session__process_pipe_events reuses the same memory buffer to
process all events in the pipe.
When reordering is needed (e.g. -b option), events are not immediately
flushed, but kept around until reordering is possible, causing
memory corruption.
The problem is usually observed by a "Unknown sample error" output. It
can easily be reproduced by:
perf record -o - noploop | perf inject -b > output
Committer testing:
Before:
$ perf record -o - stress -t 2 -c 2 | perf inject -b > /dev/null
stress: info: [8297] dispatching hogs: 2 cpu, 0 io, 0 vm, 0 hdd
stress: info: [8297] successful run completed in 2s
[ perf record: Woken up 3 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
Warning:
Found 1 unknown events!
Is this an older tool processing a perf.data file generated by a more recent tool?
If that is not the case, consider reporting to [email protected].
$
After:
$ perf record -o - stress -t 2 -c 2 | perf inject -b > /dev/null
stress: info: [9027] dispatching hogs: 2 cpu, 0 io, 0 vm, 0 hdd
stress: info: [9027] successful run completed in 2s
[ perf record: Woken up 3 times to write data ]
[ perf record: Captured and wrote 0.000 MB - ]
no symbols found in /usr/bin/stress, maybe install a debug package?
no symbols found in /usr/bin/stress, maybe install a debug package?
$
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
All paths following perf_session__process_event() in __cmd_inject() are
useless if __cmd_inject() is to fail, some depend on a correct
session->evlist.
First commit to add code that depends on session->evlist without checking
error was commmit e558a5bd8b ("perf inject: Work with files"). It has
grown since then.
Change __cmd_inject() to fail immediately after
perf_session__process_event() fails.
Signed-off-by: David Carrillo-Cisneros <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Andrew Vagin <[email protected]>
Cc: He Kuang <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Paul Turner <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Simon Que <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Wang Nan <[email protected]>
Fixes: e558a5bd8b74 ("perf inject: Work with files")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Implement simple detection for all kind of jumps and branches.
Signed-off-by: Christian Borntraeger <[email protected]>
Cc: Andreas Krebbel <[email protected]>
Cc: Hendrik Brueckner <[email protected]>
Cc: Martin Schwidefsky <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: linux-s390 <[email protected]>
Cc: [email protected] # v4.10+
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
since 4.10 perf annotate exits on s390 with an "unknown error -95".
Turns out that commit 786c1b51844d ("perf annotate: Start supporting
cross arch annotation") added a hard requirement for architecture
support when objdump is used but only provided x86 and arm support.
Meanwhile power was added so lets add s390 as well.
While at it make sure to implement the branch and jump types.
Signed-off-by: Christian Borntraeger <[email protected]>
Cc: Andreas Krebbel <[email protected]>
Cc: Hendrik Brueckner <[email protected]>
Cc: Martin Schwidefsky <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: linux-s390 <[email protected]>
Cc: [email protected] # v4.10+
Fixes: 786c1b51844 "perf annotate: Start supporting cross arch annotation"
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
We don't need to use strlen(), a var, or check for the end explicitely,
isspace('\0') is false:
[acme@jouet c]$ cat ltrim.c
#include <ctype.h>
#include <stdio.h>
static char *ltrim(char *s)
{
while (isspace(*s))
++s;
return s;
}
int main(void)
{
printf("ltrim(\"\")='%s'\n", ltrim(""));
return 0;
}
[acme@jouet c]$ ./ltrim
ltrim("")=''
[acme@jouet c]$
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Taeung Song <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
After reading command name from /proc/<pid>/status, use ltrim() and
rtrim() to strip command name, not using just while loop, isspace() and
etc.
Signed-off-by: Taeung Song <[email protected]>
Acked-by: David Ahern <[email protected]>
Cc: Don Zickus <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Man page of mmap() says that portable applications should ensure fd
argument to be -1 if MAP_ANONYMOUS flag is set as below:
```
The mapping is not backed by any file; its contents are initialized to
zero. The fd and offset arguments are ignored; however, some
implementations require fd to be -1 if MAP_ANONYMOUS (or
MAP_ANON) is specified, and portable applications
should ensure this.
```
However, few mmap() calls under selftests/vm/ uses 0 as fd though they
use MAP_ANONYMOUS flag. This commit changes the argument to be -1 as
recommended.
Signed-off-by: SeongJae Park <[email protected]>
Acked-by: Andrew Morton <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
The use of $$OUTPUT in the target shell commands resulted in an empty
string followed by an absolute path for which mkdir failed:
$ make -C tools/testing/selftests/futex
make: Entering directory '/home/dvhart/source/linux/linux-pdx86/tools/testing/selftests/futex'
Makefile:36: warning: overriding recipe for target 'clean'
../lib.mk:55: warning: ignoring old recipe for target 'clean'
for DIR in functional; do \
BUILD_TARGET=$OUTPUT/$DIR; \
mkdir $BUILD_TARGET -p; \
make OUTPUT=$BUILD_TARGET -C $DIR all;\
done
mkdir: cannot create directory ‘/functional’: Permission denied
Replace $$OUTPUT with $(OUTPUT) when referring to the Makefile OUTPUT
variable. The above make command now completes successfully.
Fixes: a8ba798bc8ec ("selftests: enable O and KBUILD_OUTPUT")
Signed-off-by: Darren Hart (VMware) <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: Shuah Khan <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
Fix to compare a zero-filled hexadecimal value with a part of
string of long hexadecimal value.
In check_types(), the last part of testcase compares with
the hex value formatted by "%x" with a part of a string of
long hex value (trimmed by tail -c and head -c). However,
if that part of long hex value contains zero (e.g. "05" of
"a3082059"), printf generated value (e.g. "5") is diffrent
string, and the test case failed.
To fix this, pass "%02x" instead of "%x" to printf.
Signed-off-by: Masami Hiramatsu <[email protected]>
Acked-by: Steven Rostedt (VMware) <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
vm tests rely on shared memory settings. Enable system V IPC to run these
tests.
Signed-off-by: Fathi Boudra <[email protected]>
Tested-by: Naresh Kamboju <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
ftrace/kprobe tests require kprobes events. Enable kprobes to run these
tests.
Signed-off-by: Fathi Boudra <[email protected]>
Tested-by: Naresh Kamboju <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
test_bitmap, test_printf and prime_numbers are expected to be built as
modules.
Signed-off-by: Fathi Boudra <[email protected]>
Tested-by: Naresh Kamboju <[email protected]>
Signed-off-by: Shuah Khan <[email protected]>
|
|
Signed-off-by: Taeung Song <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
When parsing {fore, back} ground color configs, use ltrim() instead of
just while loop and isspace().
Signed-off-by: Taeung Song <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
To strip csv output, use ltrim() instead of just while loop and
isspace() at print_metric_{only}_csv().
Signed-off-by: Taeung Song <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Wang Nan <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The kernel has a special check for a specific irq_vectors trace event.
TRACE_EVENT_PERF_PERM(irq_work_exit,
is_sampling_event(p_event) ? -EPERM : 0);
The perf-record fails for this irq_vectors event when it is present,
like when using a wildcard:
root@skl:/tmp# perf record -a -e irq_vectors:* sleep 2
Error:
You may not have permission to collect system-wide stats.
Consider tweaking /proc/sys/kernel/perf_event_paranoid,
which controls use of the performance events system by
unprivileged users (without CAP_SYS_ADMIN).
The current value is 2:
-1: Allow use of (almost) all events by all users
>= 0: Disallow raw tracepoint access by users without CAP_IOC_LOCK
>= 1: Disallow CPU event access by users without CAP_SYS_ADMIN
>= 2: Disallow kernel profiling by users without CAP_SYS_ADMIN
To make this setting permanent, edit /etc/sysctl.conf too, e.g.:
kernel.perf_event_paranoid = -1
This patch prints out the exact sub event that failed with EPERM for
wildcards to help in understanding what went wrong when this event is
present:
After the patch:
root@skl:/tmp# perf record -a -e irq_vectors:* sleep 2
Error:
No permission to enable irq_vectors:irq_work_exit event.
You may not have permission to collect system-wide stats.
......
Committer notes:
So we have a lot of irq_vectors events:
[root@jouet ~]# perf list irq_vectors:*
List of pre-defined events (to be used in -e):
irq_vectors:call_function_entry [Tracepoint event]
irq_vectors:call_function_exit [Tracepoint event]
irq_vectors:call_function_single_entry [Tracepoint event]
irq_vectors:call_function_single_exit [Tracepoint event]
irq_vectors:deferred_error_apic_entry [Tracepoint event]
irq_vectors:deferred_error_apic_exit [Tracepoint event]
irq_vectors:error_apic_entry [Tracepoint event]
irq_vectors:error_apic_exit [Tracepoint event]
irq_vectors:irq_work_entry [Tracepoint event]
irq_vectors:irq_work_exit [Tracepoint event]
irq_vectors:local_timer_entry [Tracepoint event]
irq_vectors:local_timer_exit [Tracepoint event]
irq_vectors:reschedule_entry [Tracepoint event]
irq_vectors:reschedule_exit [Tracepoint event]
irq_vectors:spurious_apic_entry [Tracepoint event]
irq_vectors:spurious_apic_exit [Tracepoint event]
irq_vectors:thermal_apic_entry [Tracepoint event]
irq_vectors:thermal_apic_exit [Tracepoint event]
irq_vectors:threshold_apic_entry [Tracepoint event]
irq_vectors:threshold_apic_exit [Tracepoint event]
irq_vectors:x86_platform_ipi_entry [Tracepoint event]
irq_vectors:x86_platform_ipi_exit [Tracepoint event]
#
And some may be sampled:
[root@jouet ~]# perf record -e irq_vectors:local* sleep 20s
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.020 MB perf.data (2 samples) ]
[root@jouet ~]# perf report -D | egrep 'stats:|events:'
Aggregated stats:
TOTAL events: 155
MMAP events: 144
COMM events: 2
EXIT events: 1
SAMPLE events: 2
MMAP2 events: 4
FINISHED_ROUND events: 1
TIME_CONV events: 1
irq_vectors:local_timer_entry stats:
TOTAL events: 1
SAMPLE events: 1
irq_vectors:local_timer_exit stats:
TOTAL events: 1
SAMPLE events: 1
[root@jouet ~]#
But, as shown in the tracepoint definition at the start of this message,
some, like "irq_vectors:irq_work_exit", may not be sampled, just counted,
i.e. if we try to sample, as when using 'perf record', we get an error:
[root@jouet ~]# perf record -e irq_vectors:irq_work_exit
Error:
You may not have permission to collect system-wide stats.
Consider tweaking /proc/sys/kernel/perf_event_paranoid,
<SNIP>
The error message is misleading, this patch will help in pointing out
what is the event causing such an error, but the error message needs
improvement, i.e. we need to figure out a way to check if a tracepoint
is counting only, like this one, when all we can do is to count it with
'perf stat', at most printing the delta using interval printing, as in:
[root@jouet ~]# perf stat -I 5000 -e irq_vectors:irq_work_*
# time counts unit events
5.000168871 0 irq_vectors:irq_work_entry
5.000168871 0 irq_vectors:irq_work_exit
10.000676730 0 irq_vectors:irq_work_entry
10.000676730 0 irq_vectors:irq_work_exit
15.001122415 0 irq_vectors:irq_work_entry
15.001122415 0 irq_vectors:irq_work_exit
20.001298051 0 irq_vectors:irq_work_entry
20.001298051 0 irq_vectors:irq_work_exit
25.001485020 1 irq_vectors:irq_work_entry
25.001485020 1 irq_vectors:irq_work_exit
30.001658706 0 irq_vectors:irq_work_entry
30.001658706 0 irq_vectors:irq_work_exit
^C 32.045711878 0 irq_vectors:irq_work_entry
32.045711878 0 irq_vectors:irq_work_exit
[root@jouet ~]#
But at least, when we use a wildcard, this patch helps a bit.
Signed-off-by: Yao Jin <[email protected]>
Tested-by: Arnaldo Carvalho de Melo <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Just avoiding non-reentrant functions.
Cc: David Ahern <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Trying to keep everything reentrant.
Cc: Namhyung Kim <[email protected]>
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
There's a conflict between ongoing level-5 paging support and
the E820 rewrite. Since the E820 rewrite is essentially ready,
merge it into x86/mm to reduce tree conflicts.
Signed-off-by: Ingo Molnar <[email protected]>
|
|
The E820 rework in WIP.x86/boot has gone through a couple of weeks
of exposure in -tip, merge it in a wider fashion.
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Linux 4.11-rc6
drm-misc needs 4.11-rc5, may as well fix conflicts with rc6.
|
|
o s/bpf_bpf_get_socket_cookie/bpf_get_socket_cookie
Signed-off-by: Alexander Alemayhu <[email protected]>
Acked-by: Daniel Borkmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 4.11:
Headed to stable:
- disable HFSCR[TM] if TM is not supported, fixes a potential host
kernel crash triggered by a hostile guest, but only in
configurations that no one uses
- don't try to fix up misaligned load-with-reservation instructions
- fix flush_(d|i)cache_range() called from modules on little endian
kernels
- add missing global TLB invalidate if cxl is active
- fix missing preempt_disable() in crc32c-vpmsum
And a fix for selftests build changes that went in this release:
- selftests/powerpc: Fix standalone powerpc build
Thanks to: Benjamin Herrenschmidt, Frederic Barrat, Oliver O'Halloran,
Paul Mackerras"
* tag 'powerpc-4.11-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/crypto/crc32c-vpmsum: Fix missing preempt_disable()
powerpc/mm: Add missing global TLB invalidate if cxl is active
powerpc/64: Fix flush_(d|i)cache_range() called from modules
powerpc: Don't try to fix up misaligned load-with-reservation instructions
powerpc: Disable HFSCR[TM] if TM is not supported
selftests/powerpc: Fix standalone powerpc build
|
|
The commit 0775a9cbc694e8c72 ("usbip: vhci extension: modifications
to vhci driver") introduced multiple controllers, and nports as a sys
file, and claimed to read the nports from it, but it didn't.
In addition, the get_nports() has been so wrong that even with 8 port
lines for instance, it gets 7 (I am guessing it is due to a '\n' mess).
Nevertheless, we fix it by reading the nports attribute.
Reviewed-by: Krzysztof Opasiak <[email protected]>
Signed-off-by: Yuyang Du <[email protected]>
Acked-by: Shuah Khan <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
since 4.10 perf annotate exits on s390 with an "unknown error -95".
Turns out that commit 786c1b51844d ("perf annotate: Start supporting
cross arch annotation") added a hard requirement for architecture
support when objdump is used but only provided x86 and arm support.
Meanwhile power was added so lets add s390 as well.
While at it make sure to implement the branch and jump types.
Signed-off-by: Christian Borntraeger <[email protected]>
Cc: Andreas Krebbel <[email protected]>
Cc: Hendrik Brueckner <[email protected]>
Cc: Martin Schwidefsky <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: linux-s390 <[email protected]>
Cc: [email protected] # v4.10+
Fixes: 786c1b51844 "perf annotate: Start supporting cross arch annotation"
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
fix artifact of merge resolution
Signed-off-by: Alexei Starovoitov <[email protected]>
Acked-by: Daniel Borkmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch add a generic testsuite for testing ethernet network device driver.
Signed-off-by: Corentin Labbe <[email protected]>
Tested-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The option 'show-total-period' works fine without a option '-l'. But if
running 'perf annotate --stdio -l --show-total-period', you can see a
problem showing only zero '0' for number of samples.
Before:
$ perf annotate --stdio -l --show-total-period
...
0 : 400816: push %rbp
0 : 400817: mov %rsp,%rbp
0 : 40081a: mov %edi,-0x24(%rbp)
0 : 40081d: mov %rsi,-0x30(%rbp)
0 : 400821: mov -0x24(%rbp),%eax
0 : 400824: mov -0x30(%rbp),%rdx
0 : 400828: mov (%rdx),%esi
0 : 40082a: mov $0x0,%edx
...
The reason is it was missed to set number of samples of
source_line_samples, so set it ordinarily.
After:
$ perf annotate --stdio -l --show-total-period
...
3 : 400816: push %rbp
4 : 400817: mov %rsp,%rbp
0 : 40081a: mov %edi,-0x24(%rbp)
0 : 40081d: mov %rsi,-0x30(%rbp)
1 : 400821: mov -0x24(%rbp),%eax
2 : 400824: mov -0x30(%rbp),%rdx
0 : 400828: mov (%rdx),%esi
1 : 40082a: mov $0x0,%edx
...
Signed-off-by: Taeung Song <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Martin Liska <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Wang Nan <[email protected]>
Fixes: 0c4a5bcea460 ("perf annotate: Display total number of samples with --show-total-period")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Trying to remove die() calls from library functions, postponing exiting
to the tool main code.
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
The callers of perf_read_values__enlarge_counters() already propagate
errors, so just print some debug diagnostics and handle allocation
failures gracefully, not trying to do silly things like 'a =
realloc(a)'.
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
We can just use the exit() right after the branch calling die().
Link: http://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
When a kretprobe is installed on a kernel function, there is a maximum
limit of how many calls in parallel it can catch (aka "maxactive"). A
kernel module could call register_kretprobe() and initialize maxactive
(see example in samples/kprobes/kretprobe_example.c).
But that is not exposed to userspace and it is currently not possible to
choose maxactive when writing to /sys/kernel/debug/tracing/kprobe_events
The default maxactive can be as low as 1 on single-core with a
non-preemptive kernel. This is too low and we need to increase it not
only for recursive functions, but for functions that sleep or resched.
This patch updates the format of the command that can be written to
kprobe_events so that maxactive can be optionally specified.
I need this for a bpf program attached to the kretprobe of
inet_csk_accept, which can sleep for a long time.
This patch includes a basic selftest:
> # ./ftracetest -v test.d/kprobe/
> === Ftrace unit tests ===
> [1] Kprobe dynamic event - adding and removing [PASS]
> [2] Kprobe dynamic event - busy event check [PASS]
> [3] Kprobe dynamic event with arguments [PASS]
> [4] Kprobes event arguments with types [PASS]
> [5] Kprobe dynamic event with function tracer [PASS]
> [6] Kretprobe dynamic event with arguments [PASS]
> [7] Kretprobe dynamic event with maxactive [PASS]
>
> # of passed: 7
> # of failed: 0
> # of unresolved: 0
> # of untested: 0
> # of unsupported: 0
> # of xfailed: 0
> # of undefined(test bug): 0
BugLink: https://github.com/iovisor/bcc/issues/1072
Link: http://lkml.kernel.org/r/[email protected]
Acked-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Alban Crequy <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-misc into perf/core
Pull perf/core improvements from Andi Kleen:
This pull requests contains updates to the Intel PMU events JSON files,
plus two one liner code fixes for the JSON files (also appended as patch)
The most remarkable change is support for Sandy Bridge to Skylake
client uncore event list support.
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|