| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
"A fix to implicit declaration warns in drivers/dma-buf test"
* tag 'linux-kselftest-fixes-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: drivers/dma-buf: Fix implicit declaration warns
|
|
For this test we are exercising the VCAP ES0 block's ability to match on
a packet with a given VLAN ID, and push an ES0 TAG A with a VID derived
from VID_A_VAL plus the classified VLAN.
$eth3.200 is the generator port
$eth0 is the bridged DUT port that receives
$eth1 is the bridged DUT port that forwards and rewrites VID 200 to 300
on egress via VCAP ES0
$eth2 is the port that receives from the DUT port $eth1
Since the egress rewriting happens outside the bridging service, VID 300
does not need to be in the bridge VLAN table of $eth1.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There will be one more VLAN modification selftest added, this time for
egress. Rename the one that exists right now to be more specific.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Looks like when I wrote the selftests I was using a network manager that
brought up the ports automatically. In order to not rely on that, let
the script open them up.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
udmabuf has the following implicit declaration warns:
udmabuf.c:30:10: warning: implicit declaration of function 'open';
udmabuf.c:42:8: warning: implicit declaration of function 'fcntl'
These are caused due to not including fcntl.h and including just
linux/fcntl.h. Fix it to include fcntl.h which will bring in the
linux/fcntl.h. In addition, define __EXPORTED_HEADERS__ to bring in
F_ADD_SEALS and F_SEAL_SHRINK defines and fix the following error
that show up when just fcntl.h is included.
udmabuf.c:45:21: error: 'F_ADD_SEALS' undeclared
45 | ret = fcntl(memfd, F_ADD_SEALS, F_SEAL_SHRINK);
| ^~~~~~~~~~~
udmabuf.c:45:34: error: 'F_SEAL_SHRINK' undeclared
45 | ret = fcntl(memfd, F_ADD_SEALS, F_SEAL_SHRINK);
| ^~~~~~~~~~~~~
Signed-off-by: Shuah Khan <[email protected]>
|
|
net/mptcp/protocol.c
977d293e23b4 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce01 ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add a selftest for checking mq children are visible after ethtool -L.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
drop statistics
Add hard drop counter check testcase, to make sure netdevsim driver
properly handles the devlink hard drop counters get/set callbacks.
Signed-off-by: Oleksandr Mazur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the commit referenced below, a check was added to devlink_lib that
asserts the existence of a devlink device referenced by $DEVLINK_DEV.
Unfortunately, several netdevsim tests point DEVLINK_DEV at a device that
does not exist at the time that devlink_lib is sourced. Thus these tests
spuriously fail.
Fix this by introducing an override. By setting DEVLINK_DEV to an empty
string, the user declares their intention to handle DEVLINK_DEV management
on their own.
In all netdevsim tests that use devlink_lib and set DEVLINK_DEV, set
instead an empty DEVLINK_DEV just before sourcing devlink_lib, and set it
to the correct value right afterwards.
Fixes: 557c4d2f780c ("selftests: devlink_lib: add check for devlink device existence")
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Several tests do not set some ports down as part of their cleanup(),
resulting in IPv6 link-local addresses and associated routes not being
deleted.
These leaks were found using a BPF tool that monitors ASIC resources.
Solve this by setting the ports down at the end of the tests.
Signed-off-by: Amit Cohen <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
To check how many routes are installed in hardware, the test runs "ip
route" and greps for "offload", which includes routes with state
"offload_failed".
Till now, this wrong check was not found because after one failure in
route insertion, the driver moved to "abort" mode, which means that user
cannot try to add more routes.
The previous patch removed the abort mechanism and now failed routes are
counted as offloaded.
Fix this by not considering routes with "offload_failed" flag as
offloaded.
Signed-off-by: Amit Cohen <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test verifies that netdevsim correctly implements devlink ops callbacks
that set node as a parent of devlink leaf or node rate object.
Co-developed-by: Vlad Buslov <[email protected]>
Signed-off-by: Vlad Buslov <[email protected]>
Signed-off-by: Dmytro Linkin <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test verifies that it is possible to create, delete and set min/max tx
rate of devlink rate node on netdevsim VF.
Co-developed-by: Vlad Buslov <[email protected]>
Signed-off-by: Vlad Buslov <[email protected]>
Signed-off-by: Dmytro Linkin <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test verifies that netdevsim VFs can set and retrieve shared/max tx
rate through new devlink API.
Co-developed-by: Vlad Buslov <[email protected]>
Signed-off-by: Vlad Buslov <[email protected]>
Signed-off-by: Dmytro Linkin <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test verifies that all netdevsim VF ports have rate leaf object created
by default.
Co-developed-by: Vlad Buslov <[email protected]>
Signed-off-by: Vlad Buslov <[email protected]>
Signed-off-by: Dmytro Linkin <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Now that the two users of this helper have been converted to iproute2 dcb,
it is not necessary anymore. Drop it.
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There is a dedicated tool for configuration of DCB in iproute2 now. Use it
in the selftest instead of mlnx_qos.
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There is a dedicated tool for configuration of DCB in iproute2 now. Use it
in the selftest instead of mlnx_qos.
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The test sometimes fails with an error message such as:
TEST: tc sample (w/ flower) rate (egress) [FAIL]
Expected 100 packets, got 70 packets, which is -30% off. Required accuracy is +-25%
Make the test more robust by generating more packets, therefore
increasing the number of expected samples. Decrease the transmission
delay in order not to needlessly prolong the test.
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, the array of the ports that were split in the port_scale test
is local, so the port_cleanup() unsplits an empty array.
Make the array global so the cleanup will be preformed properly.
Suggested-by: Petr Machata <[email protected]>
Signed-off-by: Danielle Ratson <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The mirror_gre_scale test creates as many ERSPAN sessions as the underlying
chip supports, and tests that they all work. In order to determine that it
issues a stream of ICMP packets and checks if they are mirrored as
expected.
However, the mausezahn invocation missed the -6 flag to identify the use of
IPv6 protocol, and was sending ICMP messages over IPv6, as opposed to
ICMP6. It also didn't pass an explicit source IP address, which apparently
worked at some point in the past, but does not anymore.
To fix these issues, extend the function mirror_test() in mirror_lib by
detecting the IPv6 protocol addresses, and using a different ICMP scheme.
Fix __mirror_gre_test() in the selftest itself to pass a source IP address.
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The intention behind this test is to make sure that qdisc limit is
correctly projected to the HW. However, first, due to rounding in the
qdisc, and then in the driver, the number cannot actually be accurate. And
second, the approach to testing this is to oversubscribe the port with
traffic generated on the same switch. The actual backlog size therefore
fluctuates.
In practice, this test proved to be noisier than the rest, and spuriously
fails every now and then. Increase the tolerance to 10 % to avoid these
issues.
Signed-off-by: Petr Machata <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, the resource scale test checks a few cases, when the error code
resets between the cases. So for example, if one case fails and the
consecutive case passes, the error code eventually will fit the last test
and will be 0.
Save a new return code that will hold the 'or' return codes of all the
cases, so the final return code will consider all the cases.
Signed-off-by: Danielle Ratson <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, the error return code of the failure condition is lost after
using an if statement, so the test doesn't fail when it should.
Remove the if statement that separates the condition and the error code
check, so the test won't always pass.
Fixes: abfce9e062021 ("selftests: mlxsw: Reduce running time using offload indication")
Reported-by: Ido Schimmel <[email protected]>
Signed-off-by: Danielle Ratson <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, the error return code of the failure condition is lost after
using an if statement, so the test doesn't fail when it should.
Remove the if statement that separates the condition and the error code
check, so the test won't always pass.
Fixes: 5154b1b826d9b ("selftests: mlxsw: Add a scale test for physical ports")
Reported-by: Ido Schimmel <[email protected]>
Signed-off-by: Danielle Ratson <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
There was a bug introduced during the rework which cause non-zero backlog
being stuck at ETS. Introduce a selftest that would have caught the issue
earlier.
Signed-off-by: Petr Machata <[email protected]>
Reviewed-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test FEC settings, iterate over configs.
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test that two sampling rules cannot be configured on the same port with
the same trigger.
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The driver can only offload matchall rules that do not match on a
protocol. Test that matchall rules that match on a protocol are vetoed.
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test that unsupported resilient nexthop group configurations are
rejected and that offload / trap indication is correctly set on nexthop
buckets in a resilient group.
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The number of nexthop buckets in a resilient nexthop group never
changes, so when the gateway address of a nexthop cannot be resolved,
the nexthop buckets are programmed to trap packets to the CPU in order
to trigger resolution. For example:
# ip nexthop add id 1 via 198.51.100.1 dev swp3
# ip nexthop add id 10 group 1 type resilient buckets 32
# ip nexthop bucket get id 10 index 0
id 10 index 0 idle_time 1.44 nhid 1 trap
Where 198.51.100.1 is a made-up IP.
Test that in this case packets are indeed trapped to the CPU via the
unresolved neigh trap.
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
q_in_vni_veto.sh is not needed anymore because VxLAN with an 802.1ad
bridge and VxLAN with an 802.1d bridge can coexist.
Remove the test.
Signed-off-by: Amit Cohen <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Make sure egress sampling configuration only fails on Spectrum-1, given
that mlxsw now supports it on Spectrum-{2,3}.
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test that packets are sampled when tc-sample is used with matchall
egress binding and flower classifier. Verify that when performing
sampling on egress the end-to-end latency is reported as metadata.
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test that packets are sampled when tc-sample is used and that reported
metadata is correct. Two sets of hosts (with and without LAG) are used,
since metadata extraction in mlxsw is a bit different when LAG is
involved.
# ./tc_sample.sh
TEST: tc sample rate (forward) [ OK ]
TEST: tc sample rate (local receive) [ OK ]
TEST: tc sample maximum rate [ OK ]
TEST: tc sample group conflict test [ OK ]
TEST: tc sample iif [ OK ]
TEST: tc sample lag iif [ OK ]
TEST: tc sample oif [ OK ]
TEST: tc sample lag oif [ OK ]
TEST: tc sample out-tc [ OK ]
TEST: tc sample out-tc-occ [ OK ]
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test various aspects of psample functionality over netdevsim and in
particular test that the psample module correctly reports the provided
metadata.
Example:
# ./psample.sh
TEST: psample enable / disable [ OK ]
TEST: psample group number [ OK ]
TEST: psample metadata [ OK ]
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test various aspects of the resilient nexthop group offload API on top
of the netdevsim implementation. Both good and bad flows are tested.
Signed-off-by: Ido Schimmel <[email protected]>
Co-developed-by: Petr Machata <[email protected]>
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add cases to verify that when debugfs variable "fail_route_offload" is
set, notification with "rt_offload_failed" flag is received.
Extend the existing cases to verify that when sysctl
"fib_notify_on_flag_change" is set to 2, the kernel emits notifications
only for failed route installation.
$ ./fib_notifications.sh
TEST: IPv4 route addition [ OK ]
TEST: IPv4 route deletion [ OK ]
TEST: IPv4 route replacement [ OK ]
TEST: IPv4 route offload failed [ OK ]
TEST: IPv6 route addition [ OK ]
TEST: IPv6 route deletion [ OK ]
TEST: IPv6 route replacement [ OK ]
TEST: IPv6 route offload failed [ OK ]
Signed-off-by: Amit Cohen <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test that setting lanes parameter is working.
Set max speed and max lanes in the list of advertised link modes,
and then try to set max speed with the lanes below max lanes if exists
in the list.
And then, test that setting number of lanes larger than max lanes fails.
Do the above for both autoneg on and off.
$ ./ethtool_lanes.sh
TEST: 4 lanes is autonegotiated [ OK ]
TEST: Lanes number larger than max width is not set [ OK ]
TEST: Autoneg off, 4 lanes detected during force mode [ OK ]
TEST: Lanes number larger than max width is not set [ OK ]
Signed-off-by: Danielle Ratson <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add test to check fib notifications behavior.
The test checks route addition, route deletion and route replacement for
both IPv4 and IPv6.
When fib_notify_on_flag_change=0, expect single notification for route
addition/deletion/replacement.
When fib_notify_on_flag_change=1, expect:
- two notification for route addition/replacement, first without RTM_F_TRAP
and second with RTM_F_TRAP.
- single notification for route deletion.
$ ./fib_notifications.sh
TEST: IPv4 route addition [ OK ]
TEST: IPv4 route deletion [ OK ]
TEST: IPv4 route replacement [ OK ]
TEST: IPv6 route addition [ OK ]
TEST: IPv6 route deletion [ OK ]
TEST: IPv6 route replacement [ OK ]
Signed-off-by: Amit Cohen <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Run the test cases with both `fib_notify_on_flag_change` sysctls set to
'1', and then with both sysctls set to '0' to verify there are no
regressions in the test when notifications are added.
Signed-off-by: Amit Cohen <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Query the maximum number of supported physical ports using devlink-resource
and test that this number can be reached by splitting each of the
splittable ports to its width. Test that an error is returned in case
the maximum number is exceeded.
Signed-off-by: Danielle Ratson <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from netfilter, wireless and bpf
trees.
Current release - regressions:
- mt76: fix NULL pointer dereference in mt76u_status_worker and
mt76s_process_tx_queue
- net: ipa: fix interconnect enable bug
Current release - always broken:
- netfilter: fixes possible oops in mtype_resize in ipset
- ath11k: fix number of coding issues found by static analysis tools
and spurious error messages
Previous releases - regressions:
- e1000e: re-enable s0ix power saving flows for systems with the
Intel i219-LM Ethernet controllers to fix power use regression
- virtio_net: fix recursive call to cpus_read_lock() to avoid a
deadlock
- ipv4: ignore ECN bits for fib lookups in fib_compute_spec_dst()
- sysfs: take the rtnl lock around XPS configuration
- xsk: fix memory leak for failed bind and rollback reservation at
NETDEV_TX_BUSY
- r8169: work around power-saving bug on some chip versions
Previous releases - always broken:
- dcb: validate netlink message in DCB handler
- tun: fix return value when the number of iovs exceeds MAX_SKB_FRAGS
to prevent unnecessary retries
- vhost_net: fix ubuf refcount when sendmsg fails
- bpf: save correct stopping point in file seq iteration
- ncsi: use real net-device for response handler
- neighbor: fix div by zero caused by a data race (TOCTOU)
- bareudp: fix use of incorrect min_headroom size and a false
positive lockdep splat from the TX lock
- mvpp2:
- clear force link UP during port init procedure in case
bootloader had set it
- add TCAM entry to drop flow control pause frames
- fix PPPoE with ipv6 packet parsing
- fix GoP Networking Complex Control config of port 3
- fix pkt coalescing IRQ-threshold configuration
- xsk: fix race in SKB mode transmit with shared cq
- ionic: account for vlan tag len in rx buffer len
- stmmac: ignore the second clock input, current clock framework does
not handle exclusive clock use well, other drivers may reconfigure
the second clock
Misc:
- ppp: change PPPIOCUNBRIDGECHAN ioctl request number to follow
existing scheme"
* tag 'net-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits)
net: dsa: lantiq_gswip: Fix GSWIP_MII_CFG(p) register access
net: dsa: lantiq_gswip: Enable GSWIP_MII_CFG_EN also for internal PHYs
net: lapb: Decrease the refcount of "struct lapb_cb" in lapb_device_event
r8169: work around power-saving bug on some chip versions
net: usb: qmi_wwan: add Quectel EM160R-GL
selftests: mlxsw: Set headroom size of correct port
net: macb: Correct usage of MACB_CAPS_CLK_HW_CHG flag
ibmvnic: fix: NULL pointer dereference.
docs: networking: packet_mmap: fix old config reference
docs: networking: packet_mmap: fix formatting for C macros
vhost_net: fix ubuf refcount incorrectly when sendmsg fails
bareudp: Fix use of incorrect min_headroom size
bareudp: set NETIF_F_LLTX flag
net: hdlc_ppp: Fix issues when mod_timer is called while timer is running
atlantic: remove architecture depends
erspan: fix version 1 check in gre_parse_header()
net: hns: fix return value check in __lb_other_process()
net: sched: prevent invalid Scell_log shift count
net: neighbor: fix a crash caused by mod zero
ipv4: Ignore ECN bits for fib lookups in fib_compute_spec_dst()
...
|
|
The test was setting the headroom size of the wrong port. This was not
visible because of a firmware bug that canceled this bug.
Set the headroom size of the correct port, so that the test will pass
with both old and new firmware versions.
Fixes: bfa804784e32 ("selftests: mlxsw: Add a PFC test")
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Use /usr/bin/env for shebang lines in scripts
- Remove useless -Wnested-externs warning flag
- Update documents
- Refactor log handling in modpost
- Stop building modules without MODULE_LICENSE() tag
- Make the insane combination of 'static' and EXPORT_SYMBOL an error
- Improve genksyms to handle _Static_assert()
* tag 'kbuild-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
Documentation/kbuild: Document platform dependency practises
Documentation/kbuild: Document COMPILE_TEST dependencies
genksyms: Ignore module scoped _Static_assert()
modpost: turn static exports into error
modpost: turn section mismatches to error from fatal()
modpost: change license incompatibility to error() from fatal()
modpost: turn missing MODULE_LICENSE() into error
modpost: refactor error handling and clarify error/fatal difference
modpost: rename merror() to error()
kbuild: don't hardcode depmod path
kbuild: doc: document subdir-y syntax
kbuild: doc: clarify the difference between extra-y and always-y
kbuild: doc: split if_changed explanation to a separate section
kbuild: doc: merge 'Special Rules' and 'Custom kbuild commands' sections
kbuild: doc: fix 'List directories to visit when descending' section
kbuild: doc: replace arch/$(ARCH)/ with arch/$(SRCARCH)/
kbuild: doc: update the description about kbuild Makefiles
Makefile.extrawarn: remove -Wnested-externs warning
tweewide: Fix most Shebang lines
|
|
Add tests to ensure that the forbidden and unsupported cases are indeed
vetoed by mlxsw driver.
Signed-off-by: Amit Cohen <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Change every shebang which does not need an argument to use /usr/bin/env.
This is needed as not every distro has everything under /usr/bin,
sometimes not even bash.
Signed-off-by: Finn Behrens <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Test that the reference count of a router interface (RIF) configured for
a LAG is incremented / decremented when ports join / leave the LAG. Use
the offload indication on routes configured on the RIF to understand if
it was created / destroyed.
The test fails without the previous patch.
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test that each veto that was added in the previous patch, is indeed
vetoed.
$ ./q_in_q_veto.sh
TEST: create 802.1ad vlan upper on top of a front panel [ OK ]
TEST: create 802.1ad vlan upper on top of a bridge port [ OK ]
TEST: create 802.1ad vlan upper on top of a lag [ OK ]
TEST: create 802.1ad vlan upper on top 802.1q bridge [ OK ]
TEST: create 802.1ad vlan upper on top 802.1ad bridge [ OK ]
TEST: create 802.1q vlan upper on top 802.1ad bridge [ OK ]
TEST: create vlan upper on top of front panel enslaved to 802.1ad bridge
[ OK ]
TEST: create vlan upper on top of lag enslaved to 802.1ad bridge [ OK ]
TEST: enslave front panel with vlan upper to 802.1ad bridge [ OK ]
TEST: enslave lag with vlan upper to 802.1ad bridge [ OK ]
TEST: IP address addition to 802.1ad bridge [ OK ]
TEST: switch bridge protocol [ OK ]
Signed-off-by: Danielle Ratson <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|