| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Needed for XFRM metadata tests.
Signed-off-by: Eyal Birger <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin KaFai Lau <[email protected]>
|
|
Add per port priority support for bonding active slave re-selection during
failover. A higher number means higher priority in selection. The primary
slave still has the highest priority. This option also follows the
primary_reselect rules.
This option could only be configured via netlink.
Signed-off-by: Hangbin Liu <[email protected]>
Acked-by: Jonathan Toppins <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
New netlink attributes IFLA_TSO_MAX_SIZE and IFLA_TSO_MAX_SEGS
are used to report to user-space the device TSO limits.
ip -d link sh dev eth1
...
tso_max_size 65536 tso_max_segs 65535
Signed-off-by: Eric Dumazet <[email protected]>
Acked-by: Alexander Duyck <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch add a new bonding option ns_ip6_target, which correspond
to the arp_ip_target. With this we set IPv6 targets and send IPv6 NS
request to determine the health of the link.
For other related options like the validation, we still use
arp_validate, and will change to ns_validate later.
Note: the sysfs configuration support was removed based on
https://lore.kernel.org/netdev/8863.1645071997@famine
Signed-off-by: Hangbin Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Eric Dumazet suggested to allow users to modify max GRO packet size.
We have seen GRO being disabled by users of appliances (such as
wifi access points) because of claimed bufferbloat issues,
or some work arounds in sch_cake, to split GRO/GSO packets.
Instead of disabling GRO completely, one can chose to limit
the maximum packet size of GRO packets, depending on their
latency constraints.
This patch adds a per device gro_max_size attribute
that can be changed with ip link command.
ip link set dev eth0 gro_max_size 16000
Suggested-by: Eric Dumazet <[email protected]>
Signed-off-by: Coco Li <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently, we use hard code number to verify if we are in the
arp_interval timeslice. But some user may want to reduce/extend
the verify timeslice. With the similar team option 'missed_max'
the uers could change that number based on their own environment.
Acked-by: Jay Vosburgh <[email protected]>
Signed-off-by: Hangbin Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This file has not been updated for a while.
Sync it before BIG TCP patch series.
Signed-off-by: Eric Dumazet <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The kernel provides a "/proc/sys/net/ipv6/conf/<iface>/mtu"
file, which can temporarily record the mtu value of the last
received RA message when the RA mtu value is lower than the
interface mtu, but this proc has following limitations:
(1) when the interface mtu (/sys/class/net/<iface>/mtu) is
updeated, mtu6 (/proc/sys/net/ipv6/conf/<iface>/mtu) will
be updated to the value of interface mtu;
(2) mtu6 (/proc/sys/net/ipv6/conf/<iface>/mtu) only affect
ipv6 connection, and not affect ipv4.
Therefore, when the mtu option is carried in the RA message,
there will be a problem that the user sometimes cannot obtain
RA mtu value correctly by reading mtu6.
After this patch set, if a RA message carries the mtu option,
you can send a netlink msg which nlmsg_type is RTM_GETLINK,
and then by parsing the attribute of IFLA_INET6_RA_MTU to
get the mtu value carried in the RA message received on the
inet6 device. In addition, you can also get a link notification
when ra_mtu is updated so it doesn't have to poll.
In this way, if the MTU values that the device receives from
the network in the PCO IPv4 and the RA IPv6 procedures are
different, the user can obtain the correct ipv6 ra_mtu value
and compare the value of ra_mtu and ipv4 mtu, then the device
can use the lower MTU value for both IPv4 and IPv6.
Signed-off-by: Rocco Yue <[email protected]>
Reviewed-by: David Ahern <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add an option lacp_active, which is similar with team's runner.active.
This option specifies whether to send LACPDU frames periodically. If set
on, the LACPDU frames are sent along with the configured lacp_rate
setting. If set off, the LACPDU frames acts as "speak when spoken to".
Note, the LACPDU state frames still will be sent when init or unbind port.
v2: remove module parameter
Signed-off-by: Hangbin Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Background:
Broadcast and multicast packages are enqueued for later processing.
This queue was previously hardcoded to 1000.
This proved insufficient for handling very high packet rates.
This resulted in packet drops for multicast.
While at the same time unicast worked fine.
The change:
This patch make the queue length adjustable to accommodate
for environments with very high multicast packet rate.
But still keeps the default value of 1000 unless specified.
The queue length is specified as a request per macvlan
using the IFLA_MACVLAN_BC_QUEUE_LEN parameter.
The actual used queue length will then be the maximum of
any macvlan connected to the same port. The actual used
queue length for the port can be retrieved (read only)
by the IFLA_MACVLAN_BC_QUEUE_LEN_USED parameter for verification.
This will be followed up by a patch to iproute2
in order to adjust the parameter from userspace.
Signed-off-by: Thomas Karlsson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
This patch adds a new port attribute, IFLA_BRPORT_MRP_IN_OPEN, which
allows to notify the userspace when the node lost the contiuity of
MRP_InTest frames.
Signed-off-by: Horatiu Vultur <[email protected]>
Acked-by: Nikolay Aleksandrov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds a new port attribute, IFLA_BRPORT_MRP_RING_OPEN, which allows
to notify the userspace when the port lost the continuite of MRP frames.
This attribute is set by kernel whenever the SW or HW detects that the ring is
being open or closed.
Reviewed-by: Nikolay Aleksandrov <[email protected]>
Signed-off-by: Horatiu Vultur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch adds new netlink attribute to allow a user to (optionally)
specify the desired offload mode immediately upon MACSec link creation.
Separate iproute patch will be required to support this from user space.
Signed-off-by: Mark Starovoytov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This adds the IFLA_XDP_EXPECTED_FD netlink attribute definition and the
XDP_FLAGS_REPLACE flag to if_link.h in tools/include.
Signed-off-by: Toke Høiland-Jørgensen <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
This patch adds a new MACsec offloading option, MACSEC_OFFLOAD_MAC,
allowing a user to select a MAC as a provider for MACsec offloading
operations.
Signed-off-by: Antoine Tenart <[email protected]>
Signed-off-by: Mark Starovoytov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-01-22
The following pull-request contains BPF updates for your *net-next* tree.
We've added 92 non-merge commits during the last 16 day(s) which contain
a total of 320 files changed, 7532 insertions(+), 1448 deletions(-).
The main changes are:
1) function by function verification and program extensions from Alexei.
2) massive cleanup of selftests/bpf from Toke and Andrii.
3) batched bpf map operations from Brian and Yonghong.
4) tcp congestion control in bpf from Martin.
5) bulking for non-map xdp_redirect form Toke.
6) bpf_send_signal_thread helper from Yonghong.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
This patch introduces the macsec_context structure. It will be used
in the kernel to exchange information between the common MACsec
implementation (macsec.c) and the MACsec hardware offloading
implementations. This structure contains pointers to MACsec specific
structures which contain the actual MACsec configuration, and to the
underlying device (phydev for now).
Signed-off-by: Antoine Tenart <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Sync uapi/linux/if_link.h into tools to avoid out of sync warnings during
libbpf build.
Signed-off-by: Andrii Nakryiko <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
Sync if_link.h into tools/ and get rid of annoying libbpf Makefile warning.
Signed-off-by: Andrii Nakryiko <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
To pick the changes in:
07a4ddec3ce9 ("bonding: add an option to specify a delay between peer notifications")
And silence this build warning:
Kernel ABI header at 'tools/include/uapi/linux/if_link.h' differs from latest version at 'include/uapi/linux/if_link.h'
Cc: Adrian Hunter <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Luis Cláudio Gonçalves <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Vincent Bernat <[email protected]>
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Currently, gratuitous ARP/ND packets are sent every `miimon'
milliseconds. This commit allows a user to specify a custom delay
through a new option, `peer_notif_delay'.
Like for `updelay' and `downdelay', this delay should be a multiple of
`miimon' to avoid managing an additional work queue. The configuration
logic is copied from `updelay' and `downdelay'. However, the default
value cannot be set using a module parameter: Netlink or sysfs should
be used to configure this feature.
When setting `miimon' to 100 and `peer_notif_delay' to 500, we can
observe the 500 ms delay is respected:
20:30:19.354693 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:19.874892 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:20.394919 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:20.914963 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
In bond_mii_monitor(), I have tried to keep the lock logic readable.
The change is due to the fact we cannot rely on a notification to
lower the value of `bond->send_peer_notif' as `NETDEV_NOTIFY_PEERS' is
only triggered once every N times, while we need to decrement the
counter each time.
iproute2 also needs to be updated to be able to specify this new
attribute through `ip link'.
Signed-off-by: Vincent Bernat <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Syncing if_link.h that got out of sync.
Signed-off-by: Andrii Nakryiko <[email protected]>
Acked-by: Martin KaFai Lau <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
|
|
To pick the changes from:
a428afe82f98 ("net: bridge: add support for user-controlled bool options")
a025fb5f49ad ("geneve: Allow configuration of DF behaviour")
b4d3069783bc ("vxlan: Allow configuration of DF behaviour")
Silencing this tools/ build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/if_link.h' differs from latest version at 'include/uapi/linux/if_link.h'
Cc: Adrian Hunter <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Nikolay Aleksandrov <[email protected]>
Cc: Stefano Brivio <[email protected]>
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
To pick the changes from:
9163a0fc1f0c ("net: bridge: add support for per-port vlan stats")
And silence this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/if_link.h' differs from latest version at 'include/uapi/linux/if_link.h'
Cc: Alexei Starovoitov <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Eric Leblond <[email protected]>
Cc: Nikolay Aleksandrov <[email protected]>
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <[email protected]>
|
|
Similar with commit 72f6d71e491e6 ("vxlan: add ttl inherit support"),
currently ttl == 0 means "use whatever default value" on geneve instead
of inherit inner ttl. To respect compatibility with old behavior, let's
add a new IFLA_GENEVE_TTL_INHERIT for geneve ttl inherit support.
Reported-by: Jianlin Shi <[email protected]>
Suggested-by: Jiri Benc <[email protected]>
Signed-off-by: Hangbin Liu <[email protected]>
Reviewed-by: Jiri Benc <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
To get the changes in:
3e7a50ceb11e ("net: report min and max mtu network device settings")
2756f68c3149 ("net: bridge: add support for backup port")
a25717d2b604 ("xdp: support simultaneous driver and hw XDP attachment")
4f91da26c811 ("xdp: add per mode attributes for attached programs")
f203b76d7809 ("xfrm: Add virtual xfrm interfaces")
Silencing this libbpf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/if_link.h' differs from latest version at 'include/uapi/linux/if_link.h'
Cc: Adrian Hunter <[email protected]>
Cc: Daniel Borkmann <[email protected]>
Cc: David Ahern <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Jakub Kicinski <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Nikolay Aleksandrov <[email protected]>
Cc: Steffen Klassert <[email protected]>
Cc: Stephen Hemminger <[email protected]>
Cc: Wang Nan <[email protected]>
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
This adds IFLA_TARGET_NETNSID as an alias for IFLA_IF_NETNSID for
RTM_*LINK requests.
The new name is clearer and also aligns with the newly introduced
IFA_TARGET_NETNSID propert for RTM_*ADDR requests.
Signed-off-by: Christian Brauner <[email protected]>
Suggested-by: Nicolas Dichtel <[email protected]>
Cc: Jiri Benc <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
IFLA_{BRPORT_ISOLATED,VXLAN_TTL_INHERIT}
The IFLA_BRPORT_ISOLATED and IFLA_VXLAN_TTL_INHERIT defines were added in:
7d850abd5f4e ("net: bridge: add support for port isolation")
72f6d71e491e ("vxlan: add ttl inherit support")
Pick them, silencing this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/if_link.h' differs from latest version at 'include/uapi/linux/if_link.h'
Cc: Alexei Starovoitov <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Eric Leblond <[email protected]>
Cc: Hangbin Liu <[email protected]>
Cc: Nikolay Aleksandrov <[email protected]>
Link: https://lkml.kernel.org/n/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Sync the following tooling headers with the latest kernel version:
tools/arch/arm/include/uapi/asm/kvm.h
- New ABI: KVM_REG_ARM_*
tools/arch/x86/include/asm/required-features.h
- Removal of NEED_LA57 dependency
tools/arch/x86/include/uapi/asm/kvm.h
- New KVM ABI: KVM_SYNC_X86_*
tools/include/uapi/asm-generic/mman-common.h
- New ABI: MAP_FIXED_NOREPLACE flag
tools/include/uapi/linux/bpf.h
- New ABI: BPF_F_SEQ_NUMBER functions
tools/include/uapi/linux/if_link.h
- New ABI: IFLA tun and rmnet support
tools/include/uapi/linux/kvm.h
- New ABI: hyperv eventfd and CONN_ID_MASK support plus header cleanups
tools/include/uapi/sound/asound.h
- New ABI: SNDRV_PCM_FORMAT_FIRST PCM format specifier
tools/perf/arch/x86/entry/syscalls/syscall_64.tbl
- The x86 system call table description changed due to the ptregs changes and the renames, in:
d5a00528b58c: syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()
5ac9efa3c50d: syscalls/core, syscalls/x86: Clean up compat syscall stub naming convention
ebeb8c82ffaf: syscalls/x86: Use 'struct pt_regs' based syscall calling for IA32_EMULATION and x32
Also fix the x86 syscall table warning:
-Warning: Kernel ABI header at 'tools/arch/x86/entry/syscalls/syscall_64.tbl' differs from latest version at 'arch/x86/entry/syscalls/syscall_64.tbl'
+Warning: Kernel ABI header at 'tools/perf/arch/x86/entry/syscalls/syscall_64.tbl' differs from latest version at 'arch/x86/entry/syscalls/syscall_64.tbl'
None of these changes impact existing tooling code, so we only have to copy the kernel version.
Signed-off-by: Ingo Molnar <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: Alexander Potapenko <[email protected]>
Cc: Alexander Shishkin <[email protected]>
Cc: Alexei Starovoitov <[email protected]>
Cc: Alexey Budankov <[email protected]>
Cc: Andi Kleen <[email protected]>
Cc: Andrey Ryabinin <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: Brian Robbins <[email protected]>
Cc: Clark Williams <[email protected]>
Cc: Daniel Borkmann <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Dmitriy Vyukov <[email protected]> <[email protected]>
Cc: Heiko Carstens <[email protected]>
Cc: Hendrik Brueckner <[email protected]>
Cc: Jesper Dangaard Brouer <[email protected]>
Cc: Jin Yao <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Kim Phillips <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Li Zhijian <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: Martin Liška <[email protected]>
Cc: Martin Schwidefsky <[email protected]>
Cc: Matthias Kaehlcke <[email protected]>
Cc: Miguel Bernal Marin <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Naveen N. Rao <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Ravi Bangoria <[email protected]>
Cc: Sandipan Das <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Stephen Rothwell <[email protected]>
Cc: Takuya Yamamoto <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Thomas Richter <[email protected]>
Cc: Wang Nan <[email protected]>
Cc: William Cohen <[email protected]>
Cc: Yonghong Song <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Sync the following tooling headers with the latest kernel version:
tools/arch/powerpc/include/uapi/asm/kvm.h
tools/arch/x86/include/asm/cpufeatures.h
tools/include/uapi/drm/i915_drm.h
tools/include/uapi/linux/if_link.h
tools/include/uapi/linux/kvm.h
All the changes are new ABI additions which don't impact their use
in existing tooling.
Cc: Arnaldo Carvalho de Melo <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Stephen Rothwell <[email protected]>
Cc: [email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
The headers are necessary for libbpf compilation on system with older
version of the headers.
Signed-off-by: Eric Leblond <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
|