| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull 6.11 devel branch. The conflicts in HD-audio Realtek codec driver
got resolved.
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Implement sync, output format, and input status mixer controls, to allow
the interface to be used as a straight ADAT/SPDIF (+ Headphones) I/O
interface.
This does not implement the matrix mixer, output gain controls, or input
level meter feedback. The full mixer interface is only really usable
using a dedicated userspace control app (there are too many mixer nodes
for alsamixer to be usable), so for now we leave it up to userspace to
directly control these features using raw USB control messages. This is
similar to how it's done with some FireWire interfaces (ffado-mixer).
Signed-off-by: Asahi Lina <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Add trivial support for audio streaming on the RME Digiface USB. Binds
only to the first interface to allow userspace to directly drive the
complex I/O and matrix mixer controls.
Signed-off-by: Cyan Nyan <[email protected]>
[Lina: Added 2x/4x sample rate support & boot/format quirks]
Co-developed-by: Asahi Lina <[email protected]>
Signed-off-by: Asahi Lina <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The mic in those laptops suffers too high gain resulting in mostly (fan
or else) noise being recorded. In addition to the existing fixup about
mic detection, apply also limiting its boost. While at it, extend the
quirk to also V5[46]0TNE models, which have the same issue.
Signed-off-by: Marek Marczykowski-Górecki <[email protected]>
Cc: <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Add acp71 revision id to support i2s/tdm mode.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add i2s master generation support for acp7.1 platform based on pci device
id.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add page table entry configurations to support higher sample rate
streams with multiple channels for ACP7.0 platforms.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add acp70 revision id to support I2S TDM.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Modify max channels and max sample rate support in the dai driver for
acp7.0 platform.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Set i2s bclk and lrclk for acp7.0 platform.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add I2S master clock generation support for acp7.0 platforms.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Update pcm hardware capabilities for acp7.0 platform.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add slots selection and 32-channels TDM support for
acp6.3 platform.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Update pcm hardware capabilities based on acp revision id.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
All I2S instances are connected to different powertile form acp6.0
onwards, refactor dai driver to support all I2S instances for all acp
platforms.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Refactor TDM slots selection based on acp revision id.
Signed-off-by: Venkata Prasad Potturu <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
In this function, the assignment ret is unnecessary,
thus remove it.
Signed-off-by: tangbin <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Use str_enabled_disabled() helper instead of open
coding the same.
Signed-off-by: Hongbo Li <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This patch added the support for version C.
Signed-off-by: Shuming Fan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
We used to wrap with no_free_ptr() for the return value from
memdup_user() with errors where the auto cleanup is applied. This was
a workaround because the initial implementation of kfree auto-cleanup
checked only NULL pointers.
Since recently, though, the kfree auto-cleanup checks with
IS_ERR_OR_NULL() (by the commit cd7eb8f83fcf ("mm/slab: make
__free(kfree) accept error pointers")), hence those workarounds became
superfluous. Let's drop them now.
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
1000000000L is number of ns per second, use NSEC_PER_SEC macro to replace
it to make it more readable
Signed-off-by: Jinjie Ruan <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The previous fix brought yet another compile warning at pr_debug()
call with the changed size.
Reported-by: Stephen Rothwell <[email protected]>
Closes: https://lore.kernel.org/[email protected]
Fixes: 43b42ed438bf ("ALSA: pcm: Fix the previous conversion to kstrtoul()")
Tested-by: Stephen Rothwell <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
There is a extraneous space after a newline in a dev_dbg message.
Remove it.
Signed-off-by: Colin Ian King <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The previous replacement from simple_strtoul() to kstrtoul() forgot
that the passed pointer must be an unsigned long int pointer, while
the value used there is a sized_t pointer. Fix it.
Fixes: 61bc4deff033 ("ALSA: pcm: replace simple_strtoul to kstrtoul")
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
As mentioned in [1], "...simple_strtol(), simple_strtoll(),
simple_strtoul(), and simple_strtoull() functions explicitly
ignore overflows, which may lead to unexpected results in callers."
Hence, the use of those functions is discouraged.
This patch replace the use of the simple_strtoul with the safer
alternatives kstrtoul.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#simple-strtol-simple-strtoll-simple-strtoul-simple-strtoull
Signed-off-by: Hongbo Li <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Add a test case for commit bb4485562f59 ("ASoC: cs-amp-lib: Ignore
empty UEFI calibration entries").
Any entries in the calibration blob that have calTime==0 are empty
entries. So they must not be returned by a lookup.
Signed-off-by: Richard Fitzgerald <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
sm8250 and sc7280 have lpass codec version 1.0, as these are very old
platforms, they do not have a reliable way to get the codec version
from core_id registers.
On codec versions below 2.0, even though the core_id registers are
available to read, the values of these registers are not unique to be
able to determine the version of the codec dynamically.
Add the version info into of_data, so that driver does not need to use
core_id registers to get version number for such situations.
Fixes: 378918d59181 ("ASoC: codecs: lpass-macro: add helpers to get codec version")
Signed-off-by: Srinivas Kandagatla <[email protected]>
Tested-by: Amit Pundir <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Tested-by: Bryan O'Donoghue <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add HDMI codec ID for Intel Panther Lake platform.
Signed-off-by: Kai Vehmanen <[email protected]>
Reviewed-by: Péter Ujfalusi <[email protected]>
Reviewed-by: Ranjani Sridharan <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Lenovo V145 is having phase inverted dmic but simply applying inverted
dmic fixups does not work. Chaining up verb fixes for ALC283 enables
inverting dmic fixup to work properly.
Signed-off-by: Terry Cheong <[email protected]>
Cc: <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
We do not need model specific HDA quirks to construct the component
binding details of Cirrus Logic companion amplifiers as this information
is already present in the ACPI.
Quirks are then only required for special workarounds not described in
the ACPI such as internal configuration of the Realtek codecs.
The codec pointer is now initialized in hda_component_manager_init() so
that we can detect when companion amplifiers are found in the ACPI but
the SSID invokes a quirk that also attempts to create the component
binding.
Signed-off-by: Simon Trimmer <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Pull 6.11 devel branch for applying further updates for Cirrus codecs
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Read temperature of the speaker and expose it via hwmon interface, which
will be later used during calibration of speaker protection algorithms.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This fixes the LRCLK polarity for sun8i-h3 and sun50i-h6 in i2s mode
which was wrongly inverted.
The LRCLK was being set in reversed logic compared to the DAI format:
inverted LRCLK for SND_SOC_DAIFMT_IB_NF and SND_SOC_DAIFMT_NB_NF; normal
LRCLK for SND_SOC_DAIFMT_IB_IF and SND_SOC_DAIFMT_NB_IF. Such reversed
logic applies properly for DSP_A, DSP_B, LEFT_J and RIGHT_J modes but
not for I2S mode, for which the LRCLK signal results reversed to what
expected on the bus. The issue is due to a misinterpretation of the
LRCLK polarity bit of the H3 and H6 i2s controllers. Such bit in this
case does not mean "0 => normal" or "1 => inverted" according to the
expected bus operation, but it means "0 => frame starts on low edge" and
"1 => frame starts on high edge" (from the User Manuals).
This commit fixes the LRCLK polarity by setting the LRCLK polarity bit
according to the selected bus mode and renames the LRCLK polarity bit
definition to avoid further confusion.
Fixes: dd657eae8164 ("ASoC: sun4i-i2s: Fix the LRCK polarity")
Fixes: 73adf87b7a58 ("ASoC: sun4i-i2s: Add support for H6 I2S")
Signed-off-by: Matteo Martelli <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
MSI Bravo 17 (D7VEK), like other laptops from the family,
has broken ACPI tables and needs a quirk for internal mic
to work.
Signed-off-by: Markuss Broks <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
In order to get the correct keys when using the ES8326.We will associate
SND_JACK_BTN_1 to KEY_VOLUMEUP and SND_JACK_BTN_2 to KEY_VOLUMEDOWN
when the ES8326 flag is recognized.
Signed-off-by: Zhang Yi <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Merge series from Bard Liao <[email protected]>:
Some simplifications from Brent Lu for Chromebooks, a new SoundWire codec
support from Bard Liao, new cs42l43 match entries support from
Charles Keepax, Add quirks from some new Dell laptops from Maciej
Strozek, some ACPI match entries from Balamurugan C, and few bug
fixes from Pierre-Louis Bossart.
v2:
- Add "ASoC: SOF: Intel: hda: support BT link mask in mach_params"
commit to fix the build issue in v1.
Balamurugan C (2):
ASoC: Intel: soc-acpi: Add entry for sof_es8336 in ARL match table.
ASoC: Intel: soc-acpi: Add entry for HDMI_In capture support in ARL
match table
Bard Liao (4):
ASoC: Intel: sof_sdw: add rt1320 amp support
ASoC: SOF: Intel: hda: refactoring topology name fixup for HDA mach
ASoC: Intel: sof_sdw: move ignore_internal_dmic check earlier
ASoC: Intel: sof_sdw: overwrite mach_params->dmic_num
Brent Lu (5):
ASoC: SOF: Intel: hda: refactoring topology name fixup for SDW mach
ASoC: SOF: Intel: hda: support BT link mask in mach_params
ASoC: Intel: skl_hda_dsp_generic: support BT audio offload
ASoC: Intel: skl_hda_dsp_generic: remove hdac-hdmi support
ASoC: Intel: skl_hda_dsp_generic: use sof_hdmi_private to init HDMI
Charles Keepax (3):
ASoC: Intel: soc-acpi: arl: Add match entries for new cs42l43 laptops
ASoC: Intel: soc-acpi: adl: Add match entries for new cs42l43 laptops
ASoC: Intel: soc-acpi: lnl: Add match entries for new cs42l43 laptops
Maciej Strozek (1):
ASoC: Intel: sof_sdw: Add quirks from some new Dell laptops
Pierre-Louis Bossart (2):
ASoC: Intel: sof_sdw: make sof_sdw_quirk static
ASoC: Intel: boards: always check the result of
acpi_dev_get_first_match_dev()
include/sound/soc-acpi.h | 2 +
sound/soc/intel/boards/Kconfig | 2 +-
sound/soc/intel/boards/bytcht_cx2072x.c | 4 +
sound/soc/intel/boards/bytcht_da7213.c | 4 +
sound/soc/intel/boards/bytcht_es8316.c | 2 +-
sound/soc/intel/boards/bytcr_rt5640.c | 2 +-
sound/soc/intel/boards/bytcr_rt5651.c | 2 +-
sound/soc/intel/boards/cht_bsw_rt5645.c | 4 +
sound/soc/intel/boards/cht_bsw_rt5672.c | 4 +
sound/soc/intel/boards/skl_hda_dsp_common.c | 56 ++--
sound/soc/intel/boards/skl_hda_dsp_common.h | 39 +--
sound/soc/intel/boards/skl_hda_dsp_generic.c | 58 ++--
sound/soc/intel/boards/sof_es8336.c | 12 +-
sound/soc/intel/boards/sof_sdw.c | 85 +++++-
sound/soc/intel/boards/sof_sdw_common.h | 2 -
sound/soc/intel/boards/sof_wm8804.c | 4 +
.../intel/common/soc-acpi-intel-adl-match.c | 105 +++++++
.../intel/common/soc-acpi-intel-arl-match.c | 244 +++++++++++++++
.../intel/common/soc-acpi-intel-hda-match.c | 12 +-
.../intel/common/soc-acpi-intel-lnl-match.c | 104 +++++++
sound/soc/sdw_utils/soc_sdw_rt_amp.c | 11 +-
sound/soc/sdw_utils/soc_sdw_utils.c | 19 ++
sound/soc/sof/intel/hda.c | 281 ++++++++----------
23 files changed, 780 insertions(+), 278 deletions(-)
--
2.43.0
|
|
Merge series from Kuninori Morimoto <[email protected]>:
No driver is calling snd_soc_dpcm_can_be_xxx() functions. We don't need
to have EXPORT_SYMBOL_GPL() for them. This patch-set makes it static function.
|
|
Use the IS_ERR_OR_NULL() helper instead of open-coding a
NULL and an error pointer checks to simplify the code and
improve readability.
Signed-off-by: Hongbo Li <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
No driver is calling snd_soc_dpcm_can_be_xxx() functions. We don't need
to have EXPORT_SYMBOL_GPL() for them. Let's makes it static function.
One note is that snd_soc_dpcm_fe_can_update() is not used in upstream.
Use #if-endif and keep it for future support.
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
This patch moves snd_soc_dpcm_can_be_xxx() functions to top of soc-pcm.c
This is prepare for cleanup.
Signed-off-by: Kuninori Morimoto <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add quirks for some new Dell laptops using cs42l43's speaker outputs.
Signed-off-by: Maciej Strozek <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add some new match table entries on Lunarlake for some coming cs42l43
laptops.
Signed-off-by: Charles Keepax <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add some new match table entries on Alderlake for some coming cs42l43
laptops.
Signed-off-by: Charles Keepax <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add some new match table entries on Arrowlake for some coming cs42l43
laptops.
Signed-off-by: Charles Keepax <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Use sof_hdmi_private structure instead of a link list of
skl_hda_hdmi_pcm structure for HDMI dai link initialization since
hdac-hdmi support is removed.
Signed-off-by: Brent Lu <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Kai Vehmanen <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Since this machine driver has no longer been enumerated by SKL
platform driver, we could remove hdac-hdmi support code just like
what we did to other SOF machine drivers.
Signed-off-by: Brent Lu <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Kai Vehmanen <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Adding HDMI-In capture via I2S feature support in ARL platform.
Signed-off-by: Balamurugan C <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Adding ES83x6 codec support for ARL platforms and entry in match table.
Signed-off-by: Balamurugan C <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add BT offload BE link to dai link array if the BT offload link mask
is valid (only one bit set).
Signed-off-by: Brent Lu <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
Add an new variable bt_link_mask to snd_soc_acpi_mach_params structure.
SSP port mask of BT offload found in NHLT table will be sent to
machine driver to setup BE dai link with correct SSP port number.
This patch only detects and enables the BT dailink. The functionality
will only be unlocked with a topology file that makes a reference to
that BT dailink. For backwards-compatibility reasons, this topology
will not be used by default. Chromebooks and Linux users willing to
experiment shall use the tplg_name kernel parameter to force the use
of an enhanced topology.
Signed-off-by: Brent Lu <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Signed-off-by: Bard Liao <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|