| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We did not delay after the second strobe signal, so another immediately
following access could potentially corrupt the written value.
This is a purely speculative fix with no supporting evidence, but after
taking out the spinlocks around the writes, it seems plausible that a
modern processor could be actually too fast. Also, it's just cleaner to
be consistent.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-7-oswald.buddenhagen@gmx.de>
|
|
A side effect of making the dock monitoring interrupt-driven was that
we'd be very quick to program a freshly connected dock. However, for
unclear reasons, the dock does not work when we do that - despite the
FPGA netlist upload going just fine. We work around this by adding a
delay before programming the dock; for safety, the value is several
times as much as was determined empirically.
Note that a badly timed dock hot-plug would have triggered the problem
even before the referenced commit - but now it would happen 100% instead
of about 3% of the time, thus making it impossible to work around by
re-plugging.
Fixes: fbb64eedf5a3 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-6-oswald.buddenhagen@gmx.de>
|
|
The FPGA access through the GPIO port does not interfere with other
sound processor register access, so there is no need to subject it to
emu_lock. And after moving all FPGA access out of the interrupt handler,
it does not need to be IRQ-safe, either.
What's more, attaching the dock causes a firmware upload, which takes
several seconds. We really don't want to disable IRQs for this long, and
even less also have someone else spin with IRQs disabled waiting for us.
Therefore, use a mutex for FPGA access locking.
This makes the code somewhat more noisy, as we need to wrap bigger
sections into the mutex, as it needs to enclose the spinlocks.
The latter has the "side effect" of fixing dock FPGA programming in a
corner case: a really badly timed mixer access right between entering
FPGA programming mode and uploading the netlist would mess up the
protocol.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-5-oswald.buddenhagen@gmx.de>
|
|
The actual event processing was already done by workqueue items. We can
move the event dispatching there as well, rather than doing it already
in the interrupt handler callback.
This change has a rather profound "side effect" on the reliability of
the FPGA programming: once we enter programming mode, we must not issue
any snd_emu1010_fpga_{read,write}() calls until we're done, as these
would badly mess up the programming protocol. But exactly that would
happen when trying to program the dock, as that triggers GPIO interrupts
as a side effect. This is mitigated by deferring the actual interrupt
handling, as workqueue items are not re-entrant.
To avoid scheduling the dispatcher on non-events, we now explicitly
ignore GPIO IRQs triggered by "uninteresting" pins, which happens a lot
as a side effect of calling snd_emu1010_fpga_{read,write}().
Fixes: fbb64eedf5a3 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-4-oswald.buddenhagen@gmx.de>
|
|
Pulled out of the next patch to improve its legibility.
As the function is now available, call it directly from
snd_emu10k1_emu1010_init(), thus making the MicroDock firmware loading
synchronous - there isn't really a reason not to. Note that this does
not affect the AudioDocks of rev1 cards, as these have no independent
power supplies, and thus come up only a while after the main card is
initialized.
As a drive-by, adjust the priorities of two messages to better reflect
their impact.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-3-oswald.buddenhagen@gmx.de>
|
|
While there are two separate IRQ status bits for dock attach and detach,
the hardware appears to mix them up more or less randomly, making them
useless for tracking what actually happened. It is much safer to check
the dock status separately and proceed based on that, as the old polling
code did.
Note that the code assumes that only the dock can be hot-plugged - if
other option card bits changed, the logic would break.
Fixes: fbb64eedf5a3 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-2-oswald.buddenhagen@gmx.de>
|
|
As already anticipated in the original commit, playback was broken for
very short samples. I just didn't expect it to be an actual problem,
because we're talking about less than 1.5 milliseconds here. But clearly
such wavetable samples do actually exist.
The problem was that for such short samples we'd set the current
position beyond the end of the loop, so we'd run off the end of the
sample and play garbage.
This is a bigger (more audible) problem than the original one, which was
that we'd start playback with garbage (whatever was still in the cache),
which would be mostly masked by the note's attack phase.
So revert to the old behavior for now. We'll subsequently fix it
properly with a bigger patch series.
Note that this isn't a full revert - the dead code is not re-introduced,
because that would be silly.
Fixes: df335e9a8bcb ("ALSA: emu10k1: fix synthesizer sample playback position and caching")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218625
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240401145805.528794-1-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Link: https://lore.kernel.org/r/20230720082108.31346-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ALSA: Make control API taking controls_rwsem consistently
A few ALSA control API helpers like snd_ctl_rename(), snd_ctl_remove()
and snd_ctl_find_*() suppose the callers taking card->controls_rwsem.
But it's error-prone and fragile. This patch set tries to change
those API functions to take the card->controls>rwsem internally by
themselves, so that the drivers don't need to take care of lockings.
After applying this patch set, only a couple of places still touch
card->controls_rwsem (which are OK-ish as they need for traversing the
control linked list).
Link: https://lore.kernel.org/r/20230718141304.1032-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Now that snd_ctl_find_id() takes the locking itself, we can get rid of
the messy locking in the caller side in snd_emu10k1_verify_controls().
Link: https://lore.kernel.org/r/20230718141304.1032-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For reducing the unnecessary use of controls_rwsem in the drivers,
this patch adds a new variant for snd_ctl_find_*() helpers:
snd_ctl_find_id_locked() and snd_ctl_find_numid_locked() look for a
kctl element inside the card->controls_rwsem -- that is, doing the
very same as what snd_ctl_find_id() and snd_ctl_find_numid() did until
now. snd_ctl_find_id() and snd_ctl_find_numid() remain same,
i.e. still unlocked version, but they will be switched to locked
version once after all callers are replaced.
The patch also replaces the calls of snd_ctl_find_id() and
snd_ctl_find_numid() in a few places; all of those are places where we
know that the functions are called properly with controls_rwsem held.
All others are without rwsem (although they should have been).
After this patch, we'll turn on the locking in snd_ctl_find_id() and
snd_ctl_find_numid() to be more race-free.
Link: https://lore.kernel.org/r/20230718141304.1032-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
So far, snd_ctl_remove() requires its caller to take
card->controls_rwsem manually before the call for avoiding possible
races. However, many callers don't care and miss the locking.
Basically it's cumbersome and error-prone to enforce it to each
caller. Moreover, card->controls_rwsem is a field that should be used
only by internal or proper helpers, and it's not to be touched at
random external places.
This patch is an attempt to make those calls more consistent: now
snd_ctl_remove() takes the card->controls_rwsem internally, just like
other API functions for kctls. Since a few callers already take the
controls_rwsem locks, the patch removes those locks at the same time,
too.
Link: https://lore.kernel.org/r/20230718141304.1032-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- Remove the "log-like" parts, following the same logic as the previous
commit
- Unify format
- Add missing major contributors, including myself
- Sort entries in order of first contribution (Creative comes last for
optical reasons; they don't appear to have directly contributed
anyway)
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160839.326978-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Empty BUGS and TODO sections don't really help anyone, so remove them.
Version information is chronically outdated, and not really useful in a
git world anyway, so remove it as well.
Also remove duplicated (and outdated, of course) status section from
p16v.h (the one in p16v.c is in better shape).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160839.326978-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
85;95;0c
This uses IRQs to track spontaneous changes to the word clock source
register.
FWIW, that this can happen in the first place is the reason why it is
futile to lock the clock source mixer setting while the device is open -
we can't consistently control the rate anyway. Though arguably, we
should reset any open streams when that happens, as they become
corrupted anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160738.326832-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The mixer, PCM prepare, MIDI, synth driver, and procfs callbacks are all
always invoked with IRQs enabled, so there is no point in saving the
state.
snd_emu1010_load_firmware_entry() is called from emu1010_firmware_work()
and snd_emu10k1_emu1010_init(); the latter from snd_emu10k1_create() and
snd_emu10k1_resume(), all of which have IRQs enabled.
The voice and memory functions are called from mixed contexts, so they
keep the state saving.
The low-level functions all keep the state saving, because it's not
feasible to keep track of what is called where.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230712145750.125086-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It returned zero even if the value had changed.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230712145750.125086-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
... instead of using a one-second polling timer.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230710065956.1246364-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The file is called spdif-in, but we abused it to show only sample rates
from various sources. Rectify it as far as possible (the FPGA doesn't
give us a lot of information).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-10-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixes a tentative FIXME. Because we can.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-9-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The timer was presuming a fixed 48 kHz word clock, like the rest of the
code.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-8-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is only a very partial fix - the frequency-dependent envelope & LFO
register values aren't adjusted.
But I'm not sure they were even correct at 48 kHz to start with, as most
of them are precalculated by common code which assumes an EMU8K-specific
44.1 kHz word clock, and it seems somewhat unlikely that the hardware's
register interpretation was adjusted to compensate for the different
word clock.
In any case I'm not going to spend time on fixing that, as this code is
unlikely to be actually used by anyone today.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-6-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Now that we know the actual word clock, we can:
- Put the resulting rate into the hardware info
- At 44.1 kHz word clock shift the rate for the pitch calculations,
which presume a 48 kHz word clock
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The value isn't used yet; the subsequent commits will do that.
This ignores the existence of rates above 48 kHz, which is fine, as the
hardware will just switch to the fallback clock source when fed with a
rate which is incompatible with the base clock multiplier, which
currently is always x1.
The sample rate display in /proc spdif-in is adjusted to reflect our
understanding of the input rates.
This is tested only with an 0404b card without sync card, so there is a
lot of room for improvement.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The actually available clock sources depend on the available audio input
ports and dedicated clock input ports.
This includes refactoring the code to be data-driven to remain
manageable.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
So far, we set the fallback as a side effect of setting the source. But
the fallback makes no sense at all when an internal clock is selected.
Defaulting to 48k for S/PDIF & ADAT makes sense, but as that is the
global default and we're not changing it automatically any more, it's
just fine to leave it entirely to the explicit setting.
This changes the name of the pre-existing control to something more
appropriate (regardless of the split), so users will need to adjust
their mixer settings.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- Include the FX bus map, without which the already present send routing
info would require looking up the documentation.
- Include the physical I/O channels as known to the driver
- Make the multi-channel capture map actually name the mapped input
channels rather than "FXBUS" (Audigy) or even "???" (SbLive)
- The latter two are omitted for E-MU cards, as their physical I/O is
routed through the FPGA
- While at it, make the "Card" field somewhat more useful
This includes de-duplicating the label tables between emuproc and emufx,
updating/improving the FX bus label table, and making the SB Live! 5.1
multi-track capture channel mapping hack data-driven.
Tested-by: Jonathan Dowland <jon@dow.land>
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230526101659.437969-7-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Include the routing information, which can be actually read back.
Somewhat as a drive-by, make the register dump format less obscure - the
previous one made no sense at all.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230526101659.437969-6-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It seems to make little sense to include the FX send routing, but not
the amounts.
This also simplifies the code somewhat, and lines up the output.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230526101659.437969-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
fx8010_acode is supposed to be a human-readable representation; the
binary is already in fx8010_code.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230529095504.559054-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The limits were appropriate only for the 2nd set.
FWIW, the channel count 4 for the 2nd set is suspicious as well - at
least P17V_PLAYBACK_FIFO_PTR actually has 8 channels, and comments on
HCFG2 hint at that as well. But all bitmasks are documented only for 4
channels. Anyway, rectifying that is out of scope for this patch.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230526101659.437969-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The 2nd register set belongs to the P16V chip (or embedded P17V module),
so there is nothing to show when no such part is present. Gen2 E-MU
cards have a P17V, but it's entirely unused, so we hide it there as
well.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230526101659.437969-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On SB cards the number of captured channels is derived from the voice
mask mixer control. But for E-MU cards this wasn't actually "wired up",
so changing the mask would simply mess up the recording.
We could fix that, but the channel routing through the FPGA makes the
masking redundant. So instead we hide the control, and let the user
specify the PCM channel count the traditional way.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236059-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The hardware can deal with primes up to 7 and power-of-two multiples
thereof; the limitation is reflected by the possible buffer sizes.
Note that setting the voice mask will not allow more than 16 channels
even on Sound Blaster Audigy anymore, as 32 seems a bit excessive (the
code overall appears to think so, just not in this case).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236059-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We need to specify that the hardware supports non-standard rates, as
otherwise the sound core creates a constraint which limits the rate to
the specified standard rates. That also made the rate constraint we were
already adding meaningless.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236059-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The buffer size register sets the size of the whole buffer, not just one
period. We actually handled it like that, except that the constraint was
set on the wrong parameter. The period size is implicitly constrained by
the buffer size and the fixed period count of 2.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236059-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There is no reason to nail it to 16 channels.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236023-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We use independent voices for the channels, so we need to make an effort
to ensure that they are actually in sync.
The hardware doesn't provide atomicity, so we may need to retry a few
times, due to NMIs, PCI contention, and the wrong phase of the moon.
Solution inspired by kX-project.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236023-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For unclear reasons, the extra voice was set up with half the buffer
size instead of the period size. Commit 27ae958cf6 ("emu10k1 driver -
add multichannel device hw:x,3 [2-8/8]") mentions half-loop interrupts,
so maybe this was an artifact of an earlier iteration of the patch.
While at it, also fix periods_min of the regular playback - one period
makes just no sense.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236023-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
... instead of passing in a high-level mixer struct. Let the
higher-level functions handle the differences between the voice types.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523104612.198884-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This adds snd_emu10k1_pcm_init_{voices,extra_voice}() and
snd_emu10k1_playback_{un,}mute_voices() to slightly abstract by voice
function and potential stereo property.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523104612.198884-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Instead of separate voices, we now allocate non-interleaved channels,
which may in turn contain two interleaved voices each. The higher-level
code keeps only one pointer per channel. The channels are not allocated
in one block any more, as there is no reason to do that. As a
consequence of that, and because it is cleaner regardless, we now let
the allocator store these pointers at a specified location, rather than
returning only the first one and having the calling code deduce the
remaining ones.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-8-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The voice allocator clearly knows about the field (it resets it), so
it's more consistent (and leads to less duplicated code) to have the
constructor take it as a parameter.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-7-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This saves some code duplication; no functional change.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230519184122.3808185-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This allows us to drop the code that tries to preserve already allocated
voices upon repeated hw_param callback invocations. Getting it right for
multi-channel voices would otherwise get a bit hairy.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Eliminate the MIDI type, as there is no such thing - the MPU401 port
doesn't have anything to do with voices.
For clarity, differentiate between regular and extra voices.
Don't atomize the enum into bits in the table display.
Simplify/optimize the storage.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The subsequent allocation may still fail after freeing some voices, so
we shouldn't leave them in their programmed state.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_emu10k1_voice_free() resets the hardware itself, so doing that
in the calling function as well is redundant.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On Audigy, the send amounts are merely targets, presumably to avoid
sound distortion due to sudden changes, which the EMU8K docu explicitly
warns about.
However, that "soft-start" would prevent bit-for-bit reproduction, so
we now force the current send amounts to their final values at PCM
playback init.
One might want to do that for the MIDI synthesizer as well, though it
seems mostly pointless due to the attack phase each note has anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140339.3722279-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
CPF_CURRENTPITCH starts swerving towards PTRX_PITCHTARGET as soon as
that is set. In practice this means that CPF_FRACADDRESS may acquire a
non-zero value before we manage to force CPF_CURRENTPITCH to the final
value, which would prevent bit-for-bit reproduction.
To avoid that this state persists, we now reset CPF_FRACADDRESS when
setting CPF_CURRENTPITCH, and to (mostly) avoid that it progresses too
far in the first place (possibly even reaching CCCA_CURRADDR), we write
PTRX and CPF in one critical section (though NMIs, etc. still make this
unreliable).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140339.3722279-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|