| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Usually the netpoll path, when preforming a napi poll can get away with just
polling all the napi instances of the configured device. Thats not the case for
the bonding driver however, as the napi instances which may wind up getting
flagged as needing polling after the poll_controller call don't belong to the
bonded device, but rather to the slave devices. Fix this by checking the device
in question for the IFF_MASTER flag, if set, we know we need to check the full
poll list for this cpu, rather than just the devices napi instance list.
Signed-off-by: Neil Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The bonding driver currently modifies the netpoll structure in its xmit path
while sending frames from netpoll. This is racy, as other cpus can access the
netpoll structure in parallel. Since the bonding driver points np->dev to a
slave device, other cpus can inadvertently attempt to send data directly to
slave devices, leading to improper locking with the bonding master, lost frames,
and deadlocks. This patch fixes that up.
This patch also removes the real_dev pointer from the netpoll structure as that
data is really only used by bonding in the poll_controller, and we can emulate
its behavior by check each slave for IS_UP.
Signed-off-by: Neil Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Change a few checks against the hardcoded broadcast address,
0xffffffff, to ipv4_is_lbcast(). Remove some existing checks
using ipv4_is_lbcast() that are now obviously superfluous.
Signed-off-by: Andy Walls <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix netfilter kconfig unmet dependencies warning & spell out
"compatible" while there.
warning: (IP_NF_TARGET_TTL && NET && INET && NETFILTER && IP_NF_IPTABLES && NETFILTER_ADVANCED || IP6_NF_TARGET_HL && NET && INET && IPV6 && NETFILTER && IP6_NF_IPTABLES && NETFILTER_ADVANCED) selects NETFILTER_XT_TARGET_HL which has unmet direct dependencies ((IP_NF_MANGLE || IP6_NF_MANGLE) && NETFILTER_ADVANCED)
Signed-off-by: Randy Dunlap <[email protected]>
Signed-off-by: Patrick McHardy <[email protected]>
|
|
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <[email protected]>
Cc: Maciej W. Rozycki <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Cc: Finn Thain <[email protected]>
Cc: Randy Dunlap <[email protected]>
Cc: Matt Turner <[email protected]>
Cc: Dimitry Torokhov <[email protected]>
Cc: Mike Frysinger <[email protected]>
Acked-by: Ben Pfaff <[email protected]>
Acked-by: Hans J. Koch <[email protected]>
Reviewed-by: Finn Thain <[email protected]>
Signed-off-by: Jiri Kosina <[email protected]>
|
|
Optimize processing in TIPC's bearer shutdown code, including:
1. Remove an unnecessary check to see if TIPC bearer's can exist.
2. Don't release spinlocks before calling a media-specific disabling
routine, since the routine can't sleep.
3. Make bearer_disable() operate directly on a struct bearer, instead
of needlessly taking a name and then mapping that to the struct.
Signed-off-by: Allan Stephens <[email protected]>
Signed-off-by: Paul Gortmaker <[email protected]>
Reviewed-by: Neil Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It's completely unused and exporting a static symbol
makes no sense and breaks the build.
Reported-by: Stephen Rothwell <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In error cases when the ACL is insecure or we fail to allocate a new
struct sock, we jump to the "response" label. If so, "sk" will be
null and the kernel crashes.
Signed-off-by: Nathan Holstein <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
Get rid of fib_hash_lock rwlock.
The fn_zone hash table resize is the noticeable part of this patch.
I added a seqlock per fn_zone, so that readers can restart their lookup
in the (very rare) case a writer expanded the hash table.
Add rcu heads in fib_alias and fib_node, use call_rcu() to defer their
freeing, and use appropriate _rcu list manipulations.
Stress test (160.000.000 udp frames sent, IP route cache disabled to
mimic DDOS attack, FIB_HASH)
Before:
real 0m41.191s
user 0m13.137s
sys 8m55.241s
After:
real 0m38.091s
user 0m13.189s
sys 7m53.018s
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
First step for RCU conversion of fib_hash :
struct fn_zone are created and never deleted.
Very classic conversion, using rcu_assign_pointer(), rcu_dereference()
and rtnl_dereference() verbs.
__rcu markers on fz_next and fn_zone_list
They are created under RTNL, we dont need fib_hash_lock anymore in
fn_new_zone().
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
While looking for false sharing problems, I noticed
sizeof(struct fn_zone) was small (28 bytes) and possibly sharing a cache
line with an often written kernel structure.
Most of the time, fn_zone uses its initial hash table of 16 slots.
We can avoid the false sharing problem by embedding this initial hash
table in fn_zone itself, so that sizeof(fn_zone) > L1_CACHE_BYTES
We did a similar optimization in commit a6501e080c (Reduce memory needs
and speedup lookups)
Add a fz_revorder field to speedup fn_hash() a bit.
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
As CWR is stronger than CA_Disorder state, we can miscount
SACK/Reno failure into other timeouts. Not a bad problem as
it can happen only due to ECN, FRTO detecting spurious RTO
or xmit error which are the only callers of tcp_enter_cwr.
And even then losses and RTO must still follow thereafter
to actually end up into the relevant code paths.
Compile tested.
Signed-off-by: Ilpo Järvinen <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When only fast rexmit should be done, tcp_mark_head_lost marks
L too far. Also, sacked_upto below 1 is perfectly valid number,
the packets == 0 then needs to be trapped elsewhere.
Signed-off-by: Ilpo Järvinen <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Do some cleanups of TIPC based on make namespacecheck
1. Don't export unused symbols
2. Eliminate dead code
3. Make functions and variables local
4. Rename buf_acquire to tipc_buf_acquire since it is used in several files
Compile tested only.
This make break out of tree kernel modules that depend on TIPC routines.
Signed-off-by: Stephen Hemminger <[email protected]>
Acked-by: Jon Maloy <[email protected]>
Acked-by: Paul Gortmaker <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
While doing profile analysis, I found fib_hash_table was sometime in a
cache line shared by a possibly often written kernel structure.
(CONFIG_IP_ROUTE_MULTIPATH || !CONFIG_IPV6_MULTIPLE_TABLES)
It's hard to detect because not easily reproductible.
Make sure we allocate a full cache line to keep this shared in all cpus
caches.
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
fib_table_lookup() might use fls() to speedup an open coded loop.
Noticed while doing a profile analysis.
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
fib_nl_delrule() calls synchronize_rcu() for no apparent reason,
while rtnl is held.
I suspect it was done to avoid an atomic_inc_not_zero() in
fib_rules_lookup(), which commit 7fa7cb7109d07 added anyway.
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Avoid two atomic ops on found rule in fib6_rule_lookup()
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
commit b30973f877 (node-aware skb allocation) spread a wrong habit of
allocating net drivers skbs on a given memory node : The one closest to
the NIC hardware. This is wrong because as soon as we try to scale
network stack, we need to use many cpus to handle traffic and hit
slub/slab management on cross-node allocations/frees when these cpus
have to alloc/free skbs bound to a central node.
skb allocated in RX path are ephemeral, they have a very short
lifetime : Extra cost to maintain NUMA affinity is too expensive. What
appeared as a nice idea four years ago is in fact a bad one.
In 2010, NIC hardwares are multiqueue, or we use RPS to spread the load,
and two 10Gb NIC might deliver more than 28 million packets per second,
needing all the available cpus.
Cost of cross-node handling in network and vm stacks outperforms the
small benefit hardware had when doing its DMA transfert in its 'local'
memory node at RX time. Even trying to differentiate the two allocations
done for one skb (the sk_buff on local node, the data part on NIC
hardware node) is not enough to bring good performance.
Signed-off-by: Eric Dumazet <[email protected]>
Acked-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-next-2.6 into for-davem
|
|
There's a bug with radiotap vendor namespace
parsing if you don't register for the given
namespace extensions. Fix this by passing
only the unknown vendor namespaces and the
registered data to frontends, but not both.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
|
|
Don't try to "optimize" rds_page_copy_user() by using kmap_atomic() and
the unsafe atomic user mode accessor functions. It's actually slower
than the straightforward code on any reasonable modern CPU.
Back when the code was written (although probably not by the time it was
actually merged, though), 32-bit x86 may have been the dominant
architecture. And there kmap_atomic() can be a lot faster than kmap()
(unless you have very good locality, in which case the virtual address
caching by kmap() can overcome all the downsides).
But these days, x86-64 may not be more populous, but it's getting there
(and if you care about performance, it's definitely already there -
you'd have upgraded your CPU's already in the last few years). And on
x86-64, the non-kmap_atomic() version is faster, simply because the code
is simpler and doesn't have the "re-try page fault" case.
People with old hardware are not likely to care about RDS anyway, and
the optimization for the 32-bit case is simply buggy, since it doesn't
verify the user addresses properly.
Reported-by: Dan Rosenberg <[email protected]>
Acked-by: Andrew Morton <[email protected]>
Cc: [email protected]
Signed-off-by: Linus Torvalds <[email protected]>
|
|
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <[email protected]>
Cc: Julia Lawall <[email protected]>
Cc: Christoph Hellwig <[email protected]>
|
|
Based on suggestion by Rémi Denis-Courmont to implement 'connect'
for Pipe controller logic, this patch implements 'connect' socket
call for the Pipe controller logic.
The patch does following:-
- Removes setsockopts for PNPIPE_CREATE and PNPIPE_DESTROY
- Adds setsockopt for setting the Pipe handle value
- Implements connect socket call
- Updates the Pipe controller logic
User-space should now follow below sequence with Pipe controller:-
-socket
-bind
-setsockopt for PNPIPE_PIPE_HANDLE
-connect
-setsockopt for PNPIPE_ENCAP_IP
-setsockopt for PNPIPE_ENABLE
GPRS/3G data has been tested working fine with this.
Signed-off-by: Kumar Sanghvi <[email protected]>
Acked-by: Rémi Denis-Courmont <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Remove all instances of legacy, or as yet to be implemented code
that is currently living within an #if 0 ... #endif block.
In the rare instance that some of it be needed in the future,
it can still be dragged out of history, but there is no need
for it to sit in mainline.
Signed-off-by: Paul Gortmaker <[email protected]>
Acked-by: Neil Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It looks like I submitted a different patch
than I tested, because clearly the code in
mac80211 is missing actually propagating the
requested SMPS mode. Fix that!
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
|
|
Using the frame registration notification, we
can see when probe requests are requested and
notify the low-level driver via filtering. The
flag is also set in AP and IBSS modes.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
|
|
Drivers may need to adjust their filters according
to frame registrations, so notify them about them.
Signed-off-by: Johannes Berg <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
|
|
ip_vs_dbg_callid() and IP_VS_DEBUG_CALLID() are only needed
it CONFIG_IP_VS_DEBUG is defined.
This resolves the following build warning when CONFIG_IP_VS_DEBUG is
not defined.
net/netfilter/ipvs/ip_vs_pe_sip.c:11: warning: 'ip_vs_dbg_callid' defined but not used
Reported-by: Patrick McHardy <[email protected]>
Signed-off-by: Simon Horman <[email protected]>
Signed-off-by: Patrick McHardy <[email protected]>
|
|
|
|
Signed-off-by: Jan Engelhardt <[email protected]>
|
|
Many of the used macros are just there for userspace compatibility.
Substitute the in-kernel code to directly use the terminal macro
and stuff the defines into #ifndef __KERNEL__ sections.
Signed-off-by: Jan Engelhardt <[email protected]>
|
|
The index cannot be used to reliably reconstruct a phy
name, so explicitly add the phy name to sysfs so that scripts
can figure out the parent phy device for a particular
wireless interface.
Signed-off-by: Ben Greear <[email protected]>
Signed-off-by: John W. Linville <[email protected]>
|
|
We tried very hard to remove all possible dev_hold()/dev_put() pairs in
network stack, using RCU conversions.
There is still an unavoidable device refcount change for every dst we
create/destroy, and this can slow down some workloads (routers or some
app servers, mmap af_packet)
We can switch to a percpu refcount implementation, now dynamic per_cpu
infrastructure is mature. On a 64 cpus machine, this consumes 256 bytes
per device.
On x86, dev_hold(dev) code :
before
lock incl 0x280(%ebx)
after:
movl 0x260(%ebx),%eax
incl fs:(%eax)
Stress bench :
(Sending 160.000.000 UDP frames,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_TRIE)
Before:
real 1m1.662s
user 0m14.373s
sys 12m55.960s
After:
real 0m51.179s
user 0m15.329s
sys 10m15.942s
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
|
|
Remove dead code and unused rfcomm thread events
Signed-off-by: Andrei Emeltchenko <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
Update conf_state with L2CAP_CONF_REQ_SENT before send config_req out in
l2cap_config_req().
Signed-off-by: Haijun Liu <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
&err points to the proper error set by bt_skb_send_alloc() when it
fails.
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
The Bluetooth core uses the the BD_ADDR in the opposite order from the
human readable order. So we are changing batostr() to print in the
correct order and then removing some baswap(), as they are not needed
anymore.
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
A value was attributed to 'src', but no one was using.
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
BLUETOOTH SPECIFICATION Version 4.0 [Vol 3] page 36 mentioned
"Note: Start Fragments always begin with the Basic L2CAP header
of a PDU."
Signed-off-by: Andrei Emeltchenko <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
Current Bluetooth code assembles fragments of big L2CAP packets
in l2cap_recv_acldata and then checks allowed L2CAP size in
assemled L2CAP packet (pi->imtu < skb->len).
The patch moves allowed L2CAP size check to the early stage when
we receive the first fragment of L2CAP packet. We do not need to
reserve and keep L2CAP fragments for bad packets.
Updated version after comments from Mat Martineau <[email protected]>
and Gustavo Padovan <[email protected]>.
Trace below is received when using stress tools sending big
fragmented L2CAP packets.
...
[ 1712.798492] swapper: page allocation failure. order:4, mode:0x4020
[ 1712.804809] [<c0031870>] (unwind_backtrace+0x0/0xdc) from [<c00a1f70>]
(__alloc_pages_nodemask+0x4)
[ 1712.814666] [<c00a1f70>] (__alloc_pages_nodemask+0x47c/0x4d4) from
[<c00a1fd8>] (__get_free_pages+)
[ 1712.824645] [<c00a1fd8>] (__get_free_pages+0x10/0x3c) from [<c026eb5c>]
(__alloc_skb+0x4c/0xfc)
[ 1712.833465] [<c026eb5c>] (__alloc_skb+0x4c/0xfc) from [<bf28c738>]
(l2cap_recv_acldata+0xf0/0x1f8 )
[ 1712.843322] [<bf28c738>] (l2cap_recv_acldata+0xf0/0x1f8 [l2cap]) from
[<bf0094ac>] (hci_rx_task+0x)
...
Signed-off-by: Andrei Emeltchenko <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
Clearing the blacklist in hci_dev_do_close() would mean that user space
needs to do extra work to re-block devices after a DEVDOWN-DEVUP cycle.
This patch removes the clearing of the blacklist in this case and
thereby saves user space from the extra work.
Signed-off-by: Johan Hedberg <[email protected]>
Acked-by: Ville Tervo <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
Signed-off-by: Andrei Emeltchenko <[email protected]>
Acked-by: Ville Tervo <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
L2CAP ERTM sockets can be opened with the SOCK_STREAM socket type,
which is a mandatory request for ERTM mode.
However, these sockets still have SOCK_SEQPACKET read semantics when
bt_sock_recvmsg() is used to pull data from the receive queue. If the
application is only reading part of a frame, then the unread portion
of the frame is discarded. If the application requests more bytes
than are in the current frame, only the current frame's data is
returned.
This patch utilizes common code derived from RFCOMM's recvmsg()
function to make L2CAP SOCK_STREAM reads behave like RFCOMM reads (and
other SOCK_STREAM sockets in general). The application may read one
byte at a time from the input stream and not lose any data, and may
also read across L2CAP frame boundaries.
Signed-off-by: Mat Martineau <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
To reduce code duplication, have rfcomm_sock_recvmsg() call
bt_sock_stream_recvmsg(). The common bt_sock_stream_recvmsg()
code is nearly identical, with the RFCOMM-specific functionality
for deferred setup and connection unthrottling left in
rfcomm_sock_recvmsg().
Signed-off-by: Mat Martineau <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
This commit adds a bt_sock_stream_recvmsg() function for use by any
Bluetooth code that uses SOCK_STREAM sockets. This code is copied
from rfcomm_sock_recvmsg() with minimal modifications to remove
RFCOMM-specific functionality and improve readability.
L2CAP (with the SOCK_STREAM socket type) and RFCOMM have common needs
when it comes to reading data. Proper stream read semantics require
that applications can read from a stream one byte at a time and not
lose any data. The RFCOMM code already operated on and pulled data
from the underlying L2CAP socket, so very few changes were required to
make the code more generic for use with non-RFCOMM data over L2CAP.
Applications that need more awareness of L2CAP frame boundaries are
still free to use SOCK_SEQPACKET sockets, and may verify that they
connection did not fall back to basic mode by calling getsockopt().
Signed-off-by: Mat Martineau <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
Valid L2CAP PSMs are odd numbers, and the least significant bit of the
most significant byte must be 0.
Signed-off-by: Mat Martineau <[email protected]>
Acked-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|
|
According to the ETSI 3GPP TS 07.10 the default bit rate value for RFCOMM
is 9600 bit/s. Return this bit rate in case of RPN request and accept other
sane bit rates proposed by the sender in RPM command.
Signed-off-by: Yuri Kululin <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>
Signed-off-by: Gustavo F. Padovan <[email protected]>
|