| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.
In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.
To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: Johannes Berg <[email protected]>
|
|
There's no harm in having drivers read the list, since they can
use RCU protection or RTNL locking; allow this to not require
each and every driver to also implement its own bookkeeping.
Signed-off-by: Johannes Berg <[email protected]>
|
|
The devlist_mtx mutex was removed about two years ago, in favour of just
using RTNL/RCU protection. Remove the comment still referencing it.
Signed-off-by: Johannes Berg <[email protected]>
|
|
This allows finding vendor IE from a specific vendor.
Signed-off-by: Emmanuel Grumbach <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
|
|
Some hardware (iwlwifi an example) de-aggregate AMSDUs and copy the IV
as is to the generated MPDUs, so the same PN appears in multiple
packets without being a replay attack. Allow driver to explicitly
indicate that a frame is allowed to have the same PN as the previous
frame.
Signed-off-by: Sara Sharon <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
|
|
In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, user space gets the old AP in scan
results (cached). User space may decide to roam to that old AP
which will cause a disconnection and longer recovery.
Remove APs that are probably out of range from BSS table.
Signed-off-by: David Spinadel <[email protected]>
Signed-off-by: Luca Coelho <[email protected]>
Signed-off-by: Johannes Berg <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.7 pull request
This is the first NFC pull request for 4.7. With this one we
mainly have:
- Support for NXP's pn532 NFC chipset. The pn532 is based on the same
microcontroller as the pn533, but it talks to the host through i2c
instead of USB. By separating the pn533 driver into core and PHY
parts, we can not add the i2c layer and support the pn532 chipset.
- Support for NCI's loopback mode. This is a testing mode where each
packet received by the NFCC is sent back to the DH, allowing the
host to test that the controller can receive and send data.
- A few ACPI related fixes for the STMicro drivers, in order to match
the device tree naming scheme.
- A bunch of cleanups for the st-nci and the st21nfca STMicro drivers.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The dsa_switch structure contains a dsa_chip_data member called pd.
However in the rest of the code, pd is used for dsa_platform_data.
This is confusing. Rename it cd, which is already often used in dsa.c
and slave.c for this data type.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The switch drivers only use the master_dev member for dev_info()
messages. Now that the device is passed to the old style probe, and
new style drivers are probed as true linux drivers, this is no longer
needed.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Resetting the switch is something the driver does, not the framework.
So move the parsing of this property into the driver.
There are no in kernel users of this property, so moving it does not
break anything. There is however a board which will make use of this
property making its way into the kernel.
Signed-off-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Applications such as OSPF and BFD need the original ingress device not
the VRF device; the latter can be derived from the former. To that end
add the skb_iif to inet_skb_parm and set it in ipv4 code after clearing
the skb control buffer similar to IPv6. From there the pktinfo can just
pull it from cb with the PKTINFO_SKB_CB cast.
The previous patch moving the skb->dev change to L3 means nothing else
is needed for IPv6; it just works.
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Currently the VRF driver uses the rx_handler to switch the skb device
to the VRF device. Switching the dev prior to the ip / ipv6 layer
means the VRF driver has to duplicate IP/IPv6 processing which adds
overhead and makes features such as retaining the ingress device index
more complicated than necessary.
This patch moves the hook to the L3 layer just after the first NF_HOOK
for PRE_ROUTING. This location makes exposing the original ingress device
trivial (next patch) and allows adding other NF_HOOKs to the VRF driver
in the future.
dev_queue_xmit_nit is exported so that the VRF driver can cycle the skb
with the switched device through the packet taps to maintain current
behavior (tcpdump can be used on either the vrf device or the enslaved
devices).
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Protocol for 4in6 tunnel is IPPROTO_IPIP. This was wrongly changed by
the last cleanup.
CC: Tom Herbert <[email protected]>
Fixes: 0d3c703a9d17 ("ipv6: Cleanup IPv6 tunnel receive path")
Signed-off-by: Nicolas Dichtel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
For ipgre interface in collect metadata mode, it doesn't make sense for the
interface to be of ARPHRD_IPGRE type. The outer header of received packets
is not needed, as all the information from it is present in metadata_dst. We
already don't set ipgre_header_ops for collect metadata interfaces, which is
the only consumer of mac_header pointing to the outer IP header.
Just set the interface type to ARPHRD_NONE in collect metadata mode for
ipgre (not gretap, that still correctly stays ARPHRD_ETHER) and reset
mac_header.
Fixes: a64b04d86d14 ("gre: do not assign header_ops in collect metadata mode")
Fixes: 2e15ea390e6f4 ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When using conntrack helpers from OVS, a common configuration is to
perform a lookup without specifying a helper, then go through a
firewalling policy, only to decide to attach a helper afterwards.
In this case, the initial lookup will cause a ct entry to be attached to
the skb, then the later commit with helper should attach the helper and
confirm the connection. However, the helper attachment has been missing.
If the user has enabled automatic helper attachment, then this issue
will be masked as it will be applied in init_conntrack(). It is also
masked if the action is executed from ovs_packet_cmd_execute() as that
will construct a fresh skb.
This patch fixes the issue by making an explicit call to try to assign
the helper if there is a discrepancy between the action's helper and the
current skb->nfct.
Fixes: cae3a2627520 ("openvswitch: Allow attaching helpers to ct action")
Signed-off-by: Joe Stringer <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Replace 2 arguments (cnt and rtt) in the congestion control modules'
pkts_acked() function with a struct. This will allow adding more
information without having to modify existing congestion control
modules (tcp_nv in particular needs bytes in flight when packet
was sent).
As proposed by Neal Cardwell in his comments to the tcp_nv patch.
Signed-off-by: Lawrence Brakmo <[email protected]>
Acked-by: Yuchung Cheng <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The process below was broken and is fixed with this patch.
//add an ife action and give it an instance id of 1
sudo tc actions add action ife encode \
type 0xDEAD allow mark dst 02:15:15:15:15:15 index 1
//create a filter which binds to ife action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:11 action ife index 1
Message before fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <[email protected]>
Reviewed-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The process below was broken and is fixed with this patch.
//add a skbedit action and give it an instance id of 1
sudo tc actions add action skbedit mark 10 index 1
//create a filter which binds to skbedit action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action skbedit index 1
Message before fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <[email protected]>
Reviewed-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The process below was broken and is fixed with this patch.
//add a simple action and give it an instance id of 1
sudo tc actions add action simple sdata "foobar" index 1
//create a filter which binds to simple action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action simple index 1
Message before fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <[email protected]>
Reviewed-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The process below was broken and is fixed with this patch.
//add an mirred action and give it an instance id of 1
sudo tc actions add action mirred egress mirror dev $MDEV index 1
//create a filter which binds to mirred action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action mirred index 1
Message before bug fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <[email protected]>
Reviewed-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This was broken and is fixed with this patch.
//add an ipt action and give it an instance id of 1
sudo tc actions add action ipt -j mark --set-mark 2 index 1
//create a filter which binds to ipt action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action ipt index 1
Message before bug fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <[email protected]>
Reviewed-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Late vlan action binding was broken and is fixed with this patch.
//add a vlan action to pop and give it an instance id of 1
sudo tc actions add action vlan pop index 1
//create filter which binds to vlan action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32 \
match ip dst 17.0.0.1/32 flowid 1:1 action vlan index 1
current message(before bug fix) was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <[email protected]>
Reviewed-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Antonio Quartulli says:
====================
Included changes:
- remove useless skb size check in batadv_interface_rx
- basic netns support introduced by Andrew Lunn:
- prevent virtual interface from changing netns by setting
NETIF_F_NETNS_LOCAL
- create virtual interface within the netns of the first
hard-interface
- introduce detection of complex bridge loops and report event
to the user (via udev) when the Bridge Loop Avoidance mechanism
can't prevent them
- minor reference counting bugfixes for the hard_iface object that
couldn't make it via the net tree
- use kref_get() instead of kref_get_unless_zero() to make reference
counting bug more visible
- use batadv_compare_eth() all over the code when possible instead of
plain memcmp()
- minor code cleanup and style adjustments
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
There are two instances of an unused variable, `doff' added by
commit 6fa01ccd8830 ("skbuff: Add pskb_extract() helper function")
in pskb_carve_inside_header() and pskb_carve_inside_nonlinear().
Remove these instances, they are not used.
Reported by: Daniel Borkmann <[email protected]>
Signed-off-by: Sowmini Varadhan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The handler 'ila_fill_encap_info' adds two attributes: ILA_ATTR_LOCATOR
and ILA_ATTR_CSUM_MODE.
nla_total_size_64bit() must be use for ILA_ATTR_LOCATOR.
Also, do nla_put_u8 instead of nla_put_u64 for ILA_ATTR_CSUM_MODE.
Fixes: f13a82d87b21 ("ipv6: use nla_put_u64_64bit()")
Fixes: 90bfe662db13 ("ila: add checksum neutral ILA translations")
Reported-by: Nicolas Dichtel <[email protected]>
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: Nicolas Dichtel <[email protected]>
Acked-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the very unlikely case __tcp_retransmit_skb() can not use the cloning
done in tcp_transmit_skb(), we need to refresh skb_mstamp before doing
the copy and transmit, otherwise TCP TS val will be an exact copy of
original transmit.
Fixes: 7faee5c0d514 ("tcp: remove TCP_SKB_CB(skb)->when")
Signed-off-by: Eric Dumazet <[email protected]>
Cc: Yuchung Cheng <[email protected]>
Acked-by: Yuchung Cheng <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When comparing Ethernet address it is better to use the more
generic batadv_compare_eth. The latter is also optimised for
architectures having a fast unaligned access.
Signed-off-by: Antonio Quartulli <[email protected]>
[[email protected]: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
|
|
Signed-off-by: Marek Lindner <[email protected]>
Reviewed-by: Sven Eckelmann <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
It is easier to understand that the returned value of a specific function
doesn't have to be 0 when the functions was successful when the actual
return type is bool. This is especially true when all surrounding functions
with return type int use negative values to return the error code.
Reported-by: Nicholas Krause <[email protected]>
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
_batadv_update_route requires that the caller already has a valid reference
for neigh_node. It is therefore not possible that it has an reference
counter of 0 and was still given to this function
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
The callers of the functions using batadv_hard_iface objects already make
sure that they hold a valid reference. The subfunctions don't have
to check whether the reference counter is > 0 because this was checked by
the callers.
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
batadv_gw_node_add requires that the caller already has a valid reference
for orig_node. It is therefore not possible that it has an reference
counter of 0 and was still given to this function
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
batadv_gw_select requires that the caller already has a valid reference for
new_gw_node. It is therefore not possible that it has an reference counter
of 0 and was still given to this function
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
batadv_nc_get_nc_node requires that the caller already has a valid
reference for orig_neigh_node. It is therefore not possible that it has an
reference counter of 0 and was still given to this function
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
batadv_tvlv_container_get requires that tvlv.container_list_lock is held by
the caller. It is therefore not possible that an item in
tvlv.container_list has an reference counter of 0 and is still in the list
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
The hard_iface is referenced in the packet_type for batman-adv. Increase
the refcounter of the hard_interface for it to have an explicit reference
for it in case this functionality gets refactorted and the currently
used implicit reference for it will be removed.
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
The receive function may start processing an incoming packet while the
hard_iface is shut down in a different context. All called functions called
with the batadv_hard_iface object belonging to the incoming interface would
have to check whether the reference counter is still > 0.
This is rather error-prone because this check can be forgotten easily.
Instead check the reference counter when receiving the object to make sure
that all called functions have a valid reference.
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
The batadv_hardif_list list is checked in many situations and the items
in this list are given to specialized functions to modify the routing
behavior. At the moment each of these called functions has to check
itself whether the received batadv_hard_iface has a refcount > 0 before
it can increase the reference counter and use it in other objects.
This can easily lead to problems because it is not easily visible where
all callers of a function got the batadv_hard_iface object from and
whether they already hold a valid reference.
Checking the reference counter directly before calling a subfunction
with a pointer from the batadv_hardif_list avoids this problem.
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
There are network setups where the current bridge loop avoidance can't
detect bridge loops. The minimal setup affected would consist of two
LANs and two separate meshes, connected in a ring like that:
A...(mesh1)...B
| |
(LAN1) (LAN2)
| |
C...(mesh2)...D
Since both the meshes and backbones are separate, the bridge loop
avoidance has not enough information to detect and avoid the loop
in this case. Even if these scenarios can't be fixed easily,
these kind of loops can be detected.
This patch implements a periodic check (running every 60 seconds for
now) which sends a broadcast frame with a random MAC address on
each backbone VLAN. If a broadcast frame with the same MAC address
is received shortly after on the mesh, we know that there must be a
loop and report that incident as well as throw an uevent to let others
handle that problem.
Signed-off-by: Simon Wunderlich <[email protected]>
[[email protected]: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
When creating a soft interface, create it in the same netns as the
hard interface. Replace all references to init_net with the correct
name space for the interface being manipulated.
Suggested-by: Daniel Ehlers <[email protected]>
Signed-off-by: Andrew Lunn <[email protected]>
Acked-by: Antonio Quartulli <[email protected]>
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
The batX soft interface should not be moved between network name
spaces. This is similar to bridges, bonds, tunnels, which are not
allowed to move between network namespaces.
Suggested-by: Daniel Ehlers <[email protected]>
Signed-off-by: Andrew Lunn <[email protected]>
Acked-by: Antonio Quartulli <[email protected]>
Reviewed-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
The callers of batadv_interface_rx have to make sure that enough data can
be pulled from the skb when they read the batman-adv header. The only two
functions using it are either calling pskb_may_pull with hdr_size directly
(batadv_recv_bcast_packet) or indirectly via batadv_check_unicast_packet
(batadv_recv_unicast_packet).
Reported-by: Marek Lindner <[email protected]>
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
A recent commit introduced an unconditional use of an uninitialized
variable, as reported in this gcc warning:
net/netfilter/nf_conntrack_core.c: In function '__nf_conntrack_confirm':
net/netfilter/nf_conntrack_core.c:632:33: error: 'ctinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
bytes = atomic64_read(&counter[CTINFO2DIR(ctinfo)].bytes);
^
net/netfilter/nf_conntrack_core.c:628:26: note: 'ctinfo' was declared here
enum ip_conntrack_info ctinfo;
The problem is that a local variable shadows the function parameter.
This removes the local variable, which looks like what Pablo originally
intended.
Signed-off-by: Arnd Bergmann <[email protected]>
Fixes: 71d8c47fc653 ("netfilter: conntrack: introduce clash resolution on insertion race")
Acked-by: Pablo Neira Ayuso <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contain Netfilter simple fixes for your net tree,
two one-liner and one two-liner:
1) Oneliner to fix missing spinlock definition that triggers
'BUG: spinlock bad magic on CPU#' when spinlock debugging is enabled,
from Florian Westphal.
2) Fix missing workqueue cancelation on IDLETIMER removal,
from Liping Zhang.
3) Fix insufficient validation of netlink of NFACCT_QUOTA in
nfnetlink_acct, from Phil Turnbull.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix two spots where o_flags in a tunnel are being compared to GRE_SEQ
instead of TUNNEL_SEQ.
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
We only need to reset network header here.
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Need to use adjusted protocol value for setting inner protocol.
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
GRE for IPv6 does not properly translate for GRE flags to tunnel
flags and vice versa. This patch fixes that.
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In ip6gre_tnl_link_config set t->tun_len and t->hlen correctly for the
configuration. For hard_header_len and mtu calculation include
IPv6 header and encapsulation overhead.
In ip6gre_tunnel_init_common set t->tun_len and t->hlen correctly for
the configuration. Revert to setting hard_header_len instead of
needed_headroom.
Tested:
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225
Gives MTU of 1434. That is equal to 1500 - 40 - 14 - 4 - 8.
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225 okey 123
Gives MTU of 1430. That is equal to 1500 - 40 - 14 - 4 - 8 - 4.
Signed-off-by: Tom Herbert <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|