| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
nla_nest_start may fail and thus deserves a check.
The fix returns -EMSGSIZE in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends the ncsi-netlink interface with two new commands and
three new attributes to configure multiple packages and/or channels at
once, and configure specific failover modes.
NCSI_CMD_SET_PACKAGE mask and NCSI_CMD_SET_CHANNEL_MASK set a whitelist
of packages or channels allowed to be configured with the
NCSI_ATTR_PACKAGE_MASK and NCSI_ATTR_CHANNEL_MASK attributes
respectively. If one of these whitelists is set only packages or
channels matching the whitelist are considered for the channel queue in
ncsi_choose_active_channel().
These commands may also use the NCSI_ATTR_MULTI_FLAG to signal that
multiple packages or channels may be configured simultaneously. NCSI
hardware arbitration (HWA) must be available in order to enable
multi-package mode. Multi-channel mode is always available.
If the NCSI_ATTR_CHANNEL_ID attribute is present in the
NCSI_CMD_SET_CHANNEL_MASK command the it sets the preferred channel as
with the NCSI_CMD_SET_INTERFACE command. The combination of preferred
channel and channel whitelist defines a primary channel and the allowed
failover channels.
If the NCSI_ATTR_MULTI_FLAG attribute is also present then the preferred
channel is configured for Tx/Rx and the other channels are enabled only
for Rx.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the NCSI driver is stopped with ncsi_stop_dev() the channel
monitors are stopped and the state set to "inactive". However the
channels are still configured and active from the perspective of the
network controller. We should suspend each active channel but in the
context of ncsi_stop_dev() the transmit queue has been or is about to be
stopped so we won't have time to do so.
Instead when ncsi_start_dev() is called if the NCSI topology has already
been probed then call ncsi_reset_dev() to suspend any channels that were
previously active. This resets the network controller to a known state,
provides an up to date view of channel link state, and makes sure that
mode flags such as NCSI_MODE_TX_ENABLE are properly reset.
In addition to ncsi_start_dev() use ncsi_reset_dev() in ncsi-netlink.c
to update the channel configuration more cleanly.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
command
The new command (NCSI_CMD_SEND_CMD) is added to allow user space application
to send NC-SI command to the network card.
Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response.
The work flow is as below.
Request:
User space application
-> Netlink interface (msg)
-> new Netlink handler - ncsi_send_cmd_nl()
-> ncsi_xmit_cmd()
Response:
Response received - ncsi_rcv_rsp()
-> internal response handler - ncsi_rsp_handler_xxx()
-> ncsi_rsp_handler_netlink()
-> ncsi_send_netlink_rsp ()
-> Netlink interface (msg)
-> user space application
Command timeout - ncsi_request_timeout()
-> ncsi_send_netlink_timeout ()
-> Netlink interface (msg with zero data length)
-> user space application
Error:
Error detected
-> ncsi_send_netlink_err ()
-> Netlink interface (err msg)
-> user space application
Signed-off-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ncsi_pkg_info_all_nl() .dumpit handler is missing the NLM_F_MULTI
flag, causing additional package information after the first to be lost.
Also fixup a sanity check in ncsi_write_package_info() to reject out of
range package IDs.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With CONFIG_CC_STACKPROTECTOR enabled the kernel panics as below when
parsing a NCSI_CMD_PKG_INFO command:
[ 150.149711] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08
[ 150.149711]
[ 150.159919] CPU: 0 PID: 1301 Comm: ncsi-netlink Not tainted 4.13.16-468cbec6d2c91239332cb91b1f0a73aafcb6f0c6 #1
[ 150.170004] Hardware name: Generic DT based system
[ 150.174852] [<80109930>] (unwind_backtrace) from [<80106bc4>] (show_stack+0x20/0x24)
[ 150.182641] [<80106bc4>] (show_stack) from [<805d36e4>] (dump_stack+0x20/0x28)
[ 150.189888] [<805d36e4>] (dump_stack) from [<801163ac>] (panic+0xdc/0x278)
[ 150.196780] [<801163ac>] (panic) from [<801162cc>] (__stack_chk_fail+0x20/0x24)
[ 150.204111] [<801162cc>] (__stack_chk_fail) from [<805cff08>] (ncsi_pkg_info_all_nl+0x244/0x258)
[ 150.212912] [<805cff08>] (ncsi_pkg_info_all_nl) from [<804f939c>] (genl_lock_dumpit+0x3c/0x54)
[ 150.221535] [<804f939c>] (genl_lock_dumpit) from [<804f873c>] (netlink_dump+0xf8/0x284)
[ 150.229550] [<804f873c>] (netlink_dump) from [<804f8d44>] (__netlink_dump_start+0x124/0x17c)
[ 150.237992] [<804f8d44>] (__netlink_dump_start) from [<804f9880>] (genl_rcv_msg+0x1c8/0x3d4)
[ 150.246440] [<804f9880>] (genl_rcv_msg) from [<804f9174>] (netlink_rcv_skb+0xd8/0x134)
[ 150.254361] [<804f9174>] (netlink_rcv_skb) from [<804f96a4>] (genl_rcv+0x30/0x44)
[ 150.261850] [<804f96a4>] (genl_rcv) from [<804f7790>] (netlink_unicast+0x198/0x234)
[ 150.269511] [<804f7790>] (netlink_unicast) from [<804f7ffc>] (netlink_sendmsg+0x368/0x3b0)
[ 150.277783] [<804f7ffc>] (netlink_sendmsg) from [<804abea4>] (sock_sendmsg+0x24/0x34)
[ 150.285625] [<804abea4>] (sock_sendmsg) from [<804ac1dc>] (___sys_sendmsg+0x244/0x260)
[ 150.293556] [<804ac1dc>] (___sys_sendmsg) from [<804ad98c>] (__sys_sendmsg+0x5c/0x9c)
[ 150.301400] [<804ad98c>] (__sys_sendmsg) from [<804ad9e4>] (SyS_sendmsg+0x18/0x1c)
[ 150.308984] [<804ad9e4>] (SyS_sendmsg) from [<80102640>] (ret_fast_syscall+0x0/0x3c)
[ 150.316743] ---[ end Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08
This turns out to be because the attrs array in ncsi_pkg_info_all_nl()
is initialised to a length of NCSI_ATTR_MAX which is the maximum
attribute number, not the number of attributes.
Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family")
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the message be freed immediately, no need to trim it
back to the previous size.
Inspired by commit 7a9b3ec1e19f ("nl80211: remove unnecessary genlmsg_cancel() calls")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NCSI driver defines a generic ncsi_channel_filter struct that can be
used to store arbitrarily formatted filters, and several generic methods
of accessing data stored in such a filter.
However in both the driver and as defined in the NCSI specification
there are only two actual filters: VLAN ID filters and MAC address
filters. The splitting of the MAC filter into unicast, multicast, and
mixed is also technically not necessary as these are stored in the same
location in hardware.
To save complexity, particularly in the set up and accessing of these
generic filters, remove them in favour of two specific structs. These
can be acted on directly and do not need several generic helper
functions to use.
This also fixes a memory error found by KASAN on ARM32 (which is not
upstream yet), where response handlers accessing a filter's data field
could write past allocated memory.
[ 114.926512] ==================================================================
[ 114.933861] BUG: KASAN: slab-out-of-bounds in ncsi_configure_channel+0x4b8/0xc58
[ 114.941304] Read of size 2 at addr 94888558 by task kworker/0:2/546
[ 114.947593]
[ 114.949146] CPU: 0 PID: 546 Comm: kworker/0:2 Not tainted 4.16.0-rc6-00119-ge156398bfcad #13
...
[ 115.170233] The buggy address belongs to the object at 94888540
[ 115.170233] which belongs to the cache kmalloc-32 of size 32
[ 115.181917] The buggy address is located 24 bytes inside of
[ 115.181917] 32-byte region [94888540, 94888560)
[ 115.192115] The buggy address belongs to the page:
[ 115.196943] page:9eeac100 count:1 mapcount:0 mapping:94888000 index:0x94888fc1
[ 115.204200] flags: 0x100(slab)
[ 115.207330] raw: 00000100 94888000 94888fc1 0000003f 00000001 9eea2014 9eecaa74 96c003e0
[ 115.215444] page dumped because: kasan: bad access detected
[ 115.221036]
[ 115.222544] Memory state around the buggy address:
[ 115.227384] 94888400: fb fb fb fb fc fc fc fc 04 fc fc fc fc fc fc fc
[ 115.233959] 94888480: 00 00 00 fc fc fc fc fc 00 04 fc fc fc fc fc fc
[ 115.240529] >94888500: 00 00 04 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[ 115.247077] ^
[ 115.252523] 94888580: 00 04 fc fc fc fc fc fc 06 fc fc fc fc fc fc fc
[ 115.259093] 94888600: 00 00 06 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[ 115.265639] ==================================================================
Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The call to nla_nest_start calls nla_put which can lead to a NULL
return so it's possible for attr to become NULL and we can potentially
get a NULL pointer dereference on attr. Fix this by checking for
a NULL return.
Detected by CoverityScan, CID#1466125 ("Dereference null return")
Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two error paths which are missing unlocks in this function.
Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We're supposed to use kfree_skb() to free these sk_buffs.
Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a generic netlink family for NCSI. This supports three commands;
NCSI_CMD_PKG_INFO which returns information on packages and their
associated channels, NCSI_CMD_SET_INTERFACE which allows a specific
package or package/channel combination to be set as the preferred
choice, and NCSI_CMD_CLEAR_INTERFACE which clears any preferred setting.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|