| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On Intel hardware, native_play_dead() uses mwait_play_dead() by
default and only falls back to the other methods if that fails.
That also happens during resume from hibernation, when the restore
(boot) kernel runs disable_nonboot_cpus() to take all of the CPUs
except for the boot one offline.
However, that is problematic, because the address passed to
__monitor() in mwait_play_dead() is likely to be written to in the
last phase of hibernate image restoration and that causes the "dead"
CPU to start executing instructions again. Unfortunately, the page
containing the address in that CPU's instruction pointer may not be
valid any more at that point.
First, that page may have been overwritten with image kernel memory
contents already, so the instructions the CPU attempts to execute may
simply be invalid. Second, the page tables previously used by that
CPU may have been overwritten by image kernel memory contents, so the
address in its instruction pointer is impossible to resolve then.
A report from Varun Koyyalagunta and investigation carried out by
Chen Yu show that the latter sometimes happens in practice.
To prevent it from happening, temporarily change the smp_ops.play_dead
pointer during resume from hibernation so that it points to a special
"play dead" routine which uses hlt_play_dead() and avoids the
inadvertent "revivals" of "dead" CPUs this way.
A slightly unpleasant consequence of this change is that if the
system is hibernated with one or more CPUs offline, it will generally
draw more power after resume than it did before hibernation, because
the physical state entered by CPUs via hlt_play_dead() is higher-power
than the mwait_play_dead() one in the majority of cases. It is
possible to work around this, but it is unclear how much of a problem
that's going to be in practice, so the workaround will be implemented
later if it turns out to be necessary.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=106371
Reported-by: Varun Koyyalagunta <[email protected]>
Original-by: Chen Yu <[email protected]>
Tested-by: Chen Yu <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Ingo Molnar <[email protected]>
|
|
Make it possible to protect all pages holding image data during
hibernate image restoration by setting them read-only (so as to
catch attempts to write to those pages after image data have been
stored in them).
This adds overhead to image restoration code (it may cause large
page mappings to be split as a result of page flags changes) and
the errors it protects against should never happen in theory, so
the feature is only active after passing hibernate=protect_image
to the command line of the restore kernel.
Also it only is built if CONFIG_DEBUG_RODATA is set.
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Make hibernate_setup() follow the coding style more closely by adding
some missing braces to the if () statement in it.
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
This makes pm notifier PREPARE/POST symmetrical: if PREPARE
fails, we will only undo what ever happened on PREPARE.
It fixes the unbalanced CPU hotplug enable in CPU PM notifier.
Signed-off-by: Lianwei Wang <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
With the following fix:
70595b479ce1 ("x86/power/64: Fix crash whan the hibernation code passes control to the image kernel")
... there is no longer a problem with hibernation resuming a
KASLR-booted kernel image, so remove the restriction.
Signed-off-by: Kees Cook <[email protected]>
Cc: Andy Lutomirski <[email protected]>
Cc: Baoquan He <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Brian Gerst <[email protected]>
Cc: Denys Vlasenko <[email protected]>
Cc: H. Peter Anvin <[email protected]>
Cc: Jonathan Corbet <[email protected]>
Cc: Len Brown <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Linux PM list <[email protected]>
Cc: Logan Gunthorpe <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephen Smalley <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Yinghai Lu <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
* pm-avs:
PM / AVS: rockchip-io: add io selectors and supplies for rk3399
* pm-clk:
PM / clk: Add support for obtaining clocks from device-tree
* pm-devfreq:
PM / devfreq: Spelling s/frequnecy/frequency/
* pm-sleep:
ACPI / PM: Runtime resume devices when waking from hibernate
PM / sleep: Clear pm_suspend_global_flags upon hibernate
|
|
When suspending to RAM, waking up and later suspending to disk,
we gratuitously runtime resume devices after the thaw phase.
This does not occur if we always suspend to RAM or always to disk.
pm_complete_with_resume_check(), which gets called from
pci_pm_complete() among others, schedules a runtime resume
if PM_SUSPEND_FLAG_FW_RESUME is set. The flag is set during
a suspend-to-RAM cycle. It is cleared at the beginning of
the suspend-to-RAM cycle but not afterwards and it is not
cleared during a suspend-to-disk cycle at all. Fix it.
Fixes: ef25ba047601 (PM / sleep: Add flags to indicate platform firmware involvement)
Signed-off-by: Lukas Wunner <[email protected]>
Cc: 4.4+ <[email protected]> # 4.4+
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
By default, page poisoning uses a poison value (0xaa) on free. If this
is changed to 0, the page is not only sanitized but zeroing on alloc
with __GFP_ZERO can be skipped as well. The tradeoff is that detecting
corruption from the poisoning is harder to detect. This feature also
cannot be used with hibernation since pages are not guaranteed to be
zeroed after hibernation.
Credit to Grsecurity/PaX team for inspiring this work
Signed-off-by: Laura Abbott <[email protected]>
Acked-by: Rafael J. Wysocki <[email protected]>
Cc: "Kirill A. Shutemov" <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Kees Cook <[email protected]>
Cc: Mathias Krause <[email protected]>
Cc: Dave Hansen <[email protected]>
Cc: Jianyu Zhan <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Just fix a typo in a function name in kerneldoc comments.
Signed-off-by: Geliang Tang <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
When disable_nonboot_cpus() fails on some cpu it doesn't bring back all
cpus it managed to offline, a consequent call to enable_nonboot_cpus() is
expected. In hibernation_platform_enter() we don't call
enable_nonboot_cpus() on error so cpus stay offlined.
create_image() and resume_target_kernel() functions handle
disable_nonboot_cpus() faults correctly, hibernation_platform_enter()
is the only one which is doing it wrong.
Signed-off-by: Vitaly Kuznetsov <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
This patch migrates swsusp_show_speed and its callers to using ktime_t instead
of 'struct timeval' which suffers from the y2038 problem.
Changes to swsusp_show_speed:
- use ktime_t for start and stop times
- pass start and stop times by value
Calling functions affected:
- load_image
- load_image_lzo
- save_image
- save_image_lzo
- hibernate_preallocate_memory
Design decisions:
- use ktime_t to preserve same granularity of reporting as before
- use centisecs logic as before to avoid 'div by zero' issues caused by
using seconds and nanoseconds directly
- use monotonic time (ktime_get()) since we only care about elapsed time.
Signed-off-by: Tina Ruchandani <[email protected]>
Suggested-by: Arnd Bergmann <[email protected]>
Reviewed-by: Arnd Bergmann <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
If a device's dev_pm_ops::freeze callback fails during the QUIESCE
phase, we don't rollback things correctly calling the thaw and complete
callbacks. This could leave some devices in a suspended state in case of
an error during resuming from hibernation.
Signed-off-by: Imre Deak <[email protected]>
Cc: All applicable <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
ftrace_stop() and ftrace_start() were added to the suspend and hibernate
process because there was some function within the work flow that caused
the system to reboot if it was traced. This function has recently been
found (restore_processor_state()). Now there's no reason to disable
function tracing while we are going into suspend or hibernate, which means
that being able to trace this will help tremendously in debugging any
issues with suspend or hibernate.
This also means that the ftrace_stop/start() functions can be removed
and simplify the function tracing code a bit.
Link: http://lkml.kernel.org/r/[email protected]
Acked-by: "Rafael J. Wysocki" <[email protected]>
Reviewed-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Steven Rostedt <[email protected]>
|
|
Changes kASLR from being compile-time selectable (blocked by
CONFIG_HIBERNATION), to being boot-time selectable (with hibernation
available by default) via the "kaslr" kernel command line.
Signed-off-by: Kees Cook <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
To support using kernel features that are not compatible with hibernation,
this creates the "nohibernate" kernel boot parameter to disable both
hibernation and resume. This allows hibernation support to be a boot-time
choice instead of only a compile-time choice.
Signed-off-by: Kees Cook <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Adds trace events that give finer resolution into suspend/resume. These
events are graphed in the timelines generated by the analyze_suspend.py
script. They represent large areas of time consumed that are typical to
suspend and resume.
The event is triggered by calling the function "trace_suspend_resume"
with three arguments: a string (the name of the event to be displayed
in the timeline), an integer (case specific number, such as the power
state or cpu number), and a boolean (where true is used to denote the start
of the timeline event, and false to denote the end).
The suspend_resume trace event reproduces the data that the machine_suspend
trace event did, so the latter has been removed.
Signed-off-by: Todd Brandt <[email protected]>
Acked-by: Steven Rostedt <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
In the original code "resume_delay" is an int so on 64 bits, the call to
kstrtoul() will cause memory corruption. We may as well fix a style
issue here as well and make "resume_delay" unsigned int, since that's
what we pass to ssleep().
Fixes: 317cf7e5e85e (PM / hibernate: convert simple_strtoul to kstrtoul)
Signed-off-by: Dan Carpenter <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Replace obsolete function.
Signed-off-by: Fabian Frederick <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Reboot logic in kernel/reboot will avoid calling kernel_power_off
when pm_power_off is null, and instead uses kernel_halt. Change
hibernate's power_down to follow the behavior in the reboot call.
Calling the notifier twice (once for SYS_POWER_OFF and again for
SYS_HALT) causes a panic during hibernation on Kirkwood
Openblocks A6 board.
Signed-off-by: Sebastian Capella <[email protected]>
Reported-by: Ezequiel Garcia <[email protected]>
Reviewed-by: Pavel Machek <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
do_div() needs 'u64' type, or it reports warning. And negative number
is meaningless for "speed", so change all signed to unsigned within
swsusp_show_speed().
The related warning (with allmodconfig for unicore32):
CC kernel/power/hibernate.o
kernel/power/hibernate.c: In function ‘swsusp_show_speed’:
kernel/power/hibernate.c:237: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Chen Gang <[email protected]>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Use the name_to_dev_t call to parse the device name echo'd to
to /sys/power/resume. This imitates the method used in hibernate.c
in software_resume, and allows the resume partition to be specified
using other equivalent device formats as well. By allowing
/sys/debug/resume to accept the same syntax as the resume=device
parameter, we can parse the resume=device in the init script and
use the resume device directly from the kernel command line.
Signed-off-by: Sebastian Capella <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Since create_image() only executes platform_leave() if in_suspend is
not set, enable_nonboot_cpus() is run by it with EC transactions
blocked (on ACPI systems) in the image creation code path (that is,
for in_suspend set), which may cause CPU online to fail for the CPUs
in question. In particular, this causes the acpi_cpufreq driver's
initialization to fail for those CPUs on some systems with the
following dmesg:
cpufreq: adding CPU 1
acpi_cpufreq_cpu_init
cpufreq: FREQ: 1401000 - CPU: 0
ACPI Exception: AE_BAD_PARAMETER, Returned by Handler for [EmbeddedControl] (20130725/evregion-287)
ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPC_.EC__.LPMD] (Node ffff88023249ab28), AE_BAD_PARAMETER (20130725/psparse-536)
ACPI Error: Method parse/execution failed [\_PR_.CPU0._PPC] (Node ffff88023270e3f8), AE_BAD_PARAMETER (20130725/psparse-536)
ACPI Error: Method parse/execution failed [\_PR_.CPU1._PPC] (Node ffff88023270e290), AE_BAD_PARAMETER (20130725/psparse-536)
ACPI Exception: AE_BAD_PARAMETER, Evaluating _PPC (20130725/processor_perflib-140)
cpufreq: initialization failed
CPU1 is up
To fix this problem, modify create_image() to execute platform_leave()
unconditionally. [rjw: This shouldn't lead to any significant side
effects on ACPI systems.]
Signed-off-by: Bjørn Mork <[email protected]>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
To support the ability to implement PM hibernation code as modules
the hibernation_set_ops function requires to be exported.
Similar solution already available for suspend_set_ops
(please refer to commit a5e4fd8783a2bec861ecf1138cdc042269ff59aa).
Signed-off-by: Leonardo Potenza <[email protected]>
Signed-off-by: Edwin Verplanke <[email protected]>
Reviewed-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
software_resume is being called after deferred_probe_initcall in
drivers base. If the probing of the device that contains the resume
image is deferred, and the system has been instructed to wait for
it to show up, this wait will occur in software_resume. This causes
a deadlock.
Move software_resume into late_initcall_sync so that it happens
after all the other late_initcalls.
Signed-off-by: Russ Dill <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"All of these commits are fixes that have emerged recently and some of
them fix bugs introduced during this merge window.
Specifics:
1) ACPI-based PCI hotplug (ACPIPHP) fixes related to spurious events
After the recent ACPIPHP changes we've seen some interesting
breakage on a system that triggers device check notifications
during boot for non-existing devices. Although those
notifications are really spurious, we should be able to deal with
them nevertheless and that shouldn't introduce too much overhead.
Four commits to make that work properly.
2) Memory hotplug and hibernation mutual exclusion rework
This was maent to be a cleanup, but it happens to fix a classical
ABBA deadlock between system suspend/hibernation and ACPI memory
hotplug which is possible if they are started roughly at the same
time. Three commits rework memory hotplug so that it doesn't
acquire pm_mutex and make hibernation use device_hotplug_lock
which prevents it from racing with memory hotplug.
3) ACPI Intel LPSS (Low-Power Subsystem) driver crash fix
The ACPI LPSS driver crashes during boot on Apple Macbook Air with
Haswell that has slightly unusual BIOS configuration in which one
of the LPSS device's _CRS method doesn't return all of the
information expected by the driver. Fix from Mika Westerberg, for
stable.
4) ACPICA fix related to Store->ArgX operation
AML interpreter fix for obscure breakage that causes AML to be
executed incorrectly on some machines (observed in practice).
From Bob Moore.
5) ACPI core fix for PCI ACPI device objects lookup
There still are cases in which there is more than one ACPI device
object matching a given PCI device and we don't choose the one
that the BIOS expects us to choose, so this makes the lookup take
more criteria into account in those cases.
6) Fix to prevent cpuidle from crashing in some rare cases
If the result of cpuidle_get_driver() is NULL, which can happen on
some systems, cpuidle_driver_ref() will crash trying to use that
pointer and the Daniel Fu's fix prevents that from happening.
7) cpufreq fixes related to CPU hotplug
Stephen Boyd reported a number of concurrency problems with
cpufreq related to CPU hotplug which are addressed by a series of
fixes from Srivatsa S Bhat and Viresh Kumar.
8) cpufreq fix for time conversion in time_in_state attribute
Time conversion carried out by cpufreq when user space attempts to
read /sys/devices/system/cpu/cpu*/cpufreq/stats/time_in_state
won't work correcty if cputime_t doesn't map directly to jiffies.
Fix from Andreas Schwab.
9) Revert of a troublesome cpufreq commit
Commit 7c30ed5 (cpufreq: make sure frequency transitions are
serialized) was intended to address some known concurrency
problems in cpufreq related to the ordering of transitions, but
unfortunately it introduced several problems of its own, so I
decided to revert it now and address the original problems later
in a more robust way.
10) Intel Haswell CPU models for intel_pstate from Nell Hardcastle.
11) cpufreq fixes related to system suspend/resume
The recent cpufreq changes that made it preserve CPU sysfs
attributes over suspend/resume cycles introduced a possible NULL
pointer dereference that caused it to crash during the second
attempt to suspend. Three commits from Srivatsa S Bhat fix that
problem and a couple of related issues.
12) cpufreq locking fix
cpufreq_policy_restore() should acquire the lock for reading, but
it acquires it for writing. Fix from Lan Tianyu"
* tag 'pm+acpi-fixes-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (25 commits)
cpufreq: Acquire the lock in cpufreq_policy_restore() for reading
cpufreq: Prevent problems in update_policy_cpu() if last_cpu == new_cpu
cpufreq: Restructure if/else block to avoid unintended behavior
cpufreq: Fix crash in cpufreq-stats during suspend/resume
intel_pstate: Add Haswell CPU models
Revert "cpufreq: make sure frequency transitions are serialized"
cpufreq: Use signed type for 'ret' variable, to store negative error values
cpufreq: Remove temporary fix for race between CPU hotplug and sysfs-writes
cpufreq: Synchronize the cpufreq store_*() routines with CPU hotplug
cpufreq: Invoke __cpufreq_remove_dev_finish() after releasing cpu_hotplug.lock
cpufreq: Split __cpufreq_remove_dev() into two parts
cpufreq: Fix wrong time unit conversion
cpufreq: serialize calls to __cpufreq_governor()
cpufreq: don't allow governor limits to be changed when it is disabled
ACPI / bind: Prefer device objects with _STA to those without it
ACPI / hotplug / PCI: Avoid parent bus rescans on spurious device checks
ACPI / hotplug / PCI: Use _OST to notify firmware about notify status
ACPI / hotplug / PCI: Avoid doing too much for spurious notifies
ACPICA: Fix for a Store->ArgX when ArgX contains a reference to a field.
ACPI / hotplug / PCI: Don't trim devices before scanning the namespace
...
|
|
Since all of the memory hotplug operations have to be carried out
under device_hotplug_lock, they won't need to acquire pm_mutex if
device_hotplug_lock is held around hibernation.
For this reason, make the hibernation code acquire
device_hotplug_lock after freezing user space processes and
release it before thawing them. At the same tim drop the
lock_system_sleep() and unlock_system_sleep() calls from
lock_memory_hotplug() and unlock_memory_hotplug(), respectively.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Toshi Kani <[email protected]>
|
|
The hibernation core uses special memory bitmaps during image
creation and restoration and traditionally those bitmaps are
allocated before freezing tasks, because in the past GFP_KERNEL
allocations might not work after all tasks had been frozen.
However, this is an anachronism, because hibernation_snapshot()
now calls hibernate_preallocate_memory() which allocates memory
for the image upfront anyway, so the memory bitmaps may be
allocated after freezing user space safely.
For this reason, move all of the create_basic_memory_bitmaps()
calls after freeze_processes() and all of the corresponding
free_basic_memory_bitmaps() calls before thaw_processes().
This will allow us to hold device_hotplug_lock around hibernation
without the need to worry about freezing issues with user space
processes attempting to acquire it via sysfs attributes after the
creation of memory bitmaps and before the freezing of tasks.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Toshi Kani <[email protected]>
|
|
visible
Signed-off-by: Andi Kleen <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: H. Peter Anvin <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
- ACPI conversion to PM handling based on struct dev_pm_ops.
- Conversion of a number of platform drivers to PM handling based on
struct dev_pm_ops and removal of empty legacy PM callbacks from a
couple of PCI drivers.
- Suspend-to-both for in-kernel hibernation from Bojan Smojver.
- cpuidle fixes and cleanups from ShuoX Liu, Daniel Lezcano and Preeti
Murthy.
- cpufreq bug fixes from Jonghwa Lee and Stephen Boyd.
- Suspend and hibernate fixes from Srivatsa Bhat and Colin Cross.
- Generic PM domains framework updates.
- RTC CMOS wakeup signaling update from Paul Fox.
- sparse warnings fixes from Sachin Kamat.
- Build warnings fixes for the generic PM domains framework and PM
sysfs code.
- sysfs switch for printing device suspend times from Sameer Nanda.
- Documentation fix from Oskar Schirmer.
* tag 'pm-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (70 commits)
cpufreq: Fix sysfs deadlock with concurrent hotplug/frequency switch
EXYNOS: bugfix on retrieving old_index from freqs.old
PM / Sleep: call early resume handlers when suspend_noirq fails
PM / QoS: Use NULL pointer instead of plain integer in qos.c
PM / QoS: Use NULL pointer instead of plain integer in pm_qos.h
PM / Sleep: Require CAP_BLOCK_SUSPEND to use wake_lock/wake_unlock
PM / Sleep: Add missing static storage class specifiers in main.c
cpuilde / ACPI: remove time from acpi_processor_cx structure
cpuidle / ACPI: remove usage from acpi_processor_cx structure
cpuidle / ACPI : remove latency_ticks from acpi_processor_cx structure
rtc-cmos: report wakeups from interrupt handler
PM / Sleep: Fix build warning in sysfs.c for CONFIG_PM_SLEEP unset
PM / Domains: Fix build warning for CONFIG_PM_RUNTIME unset
olpc-xo15-sci: Use struct dev_pm_ops for power management
PM / Domains: Replace plain integer with NULL pointer in domain.c file
PM / Domains: Add missing static storage class specifier in domain.c file
PM / crypto / ux500: Use struct dev_pm_ops for power management
PM / IPMI: Remove empty legacy PCI PM callbacks
tpm_nsc: Use struct dev_pm_ops for power management
tpm_tis: Use struct dev_pm_ops for power management
...
|
|
Commit a7a20d103994 ("sd: limit the scope of the async probe domain")
make the SCSI device probing run device discovery in it's own async
domain.
However, as a result, the partition detection was no longer synchronized
by async_synchronize_full() (which, despite the name, only synchronizes
the global async space, not all of them). Which in turn meant that
"wait_for_device_probe()" would not wait for the SCSI partitions to be
parsed.
And "wait_for_device_probe()" was what the boot time init code relied on
for mounting the root filesystem.
Now, most people never noticed this, because not only is it
timing-dependent, but modern distributions all use initrd. So the root
filesystem isn't actually on a disk at all. And then before they
actually mount the final disk filesystem, they will have loaded the
scsi-wait-scan module, which not only does the expected
wait_for_device_probe(), but also does scsi_complete_async_scans().
[ Side note: scsi_complete_async_scans() had also been partially broken,
but that was fixed in commit 43a8d39d0137 ("fix async probe
regression"), so that same commit a7a20d103994 had actually broken
setups even if you used scsi-wait-scan explicitly ]
Solve this problem by just moving the scsi_complete_async_scans() call
into wait_for_device_probe(). Everybody who wants to wait for device
probing to finish really wants the SCSI probing to complete, so there's
no reason not to do this.
So now "wait_for_device_probe()" really does what the name implies, and
properly waits for device probing to finish. This also removes the now
unnecessary extra calls to scsi_complete_async_scans().
Reported-and-tested-by: Artem S. Tashkinov <[email protected]>
Cc: Dan Williams <[email protected]>
Cc: Alan Stern <[email protected]>
Cc: James Bottomley <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: linux-scsi <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
If function tracing is enabled for some of the low-level suspend/resume
functions, it leads to triple fault during resume from suspend, ultimately
ending up in a reboot instead of a resume (or a total refusal to come out
of suspended state, on some machines).
This issue was explained in more detail in commit f42ac38c59e0a03d (ftrace:
disable tracing for suspend to ram). However, the changes made by that commit
got reverted by commit cbe2f5a6e84eebb (tracing: allow tracing of
suspend/resume & hibernation code again). So, unfortunately since things are
not yet robust enough to allow tracing of low-level suspend/resume functions,
suspend/resume is still broken when ftrace is enabled.
So fix this by disabling function tracing during suspend/resume & hibernation.
Signed-off-by: Srivatsa S. Bhat <[email protected]>
Cc: [email protected]
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
It is often useful to suspend to memory after hibernation image has been
written to disk. If the battery runs out or power is otherwise lost, the
computer will resume from the hibernated image. If not, it will resume
from memory and hibernation image will be discarded.
Signed-off-by: Bojan Smojver <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
integer format
Sometimes resume= parameter comes in integer style (e.g. major:minor)
and then name_to_dev_t can not detect partition properly. (especially
async device like usb, mmc).
This patch calls get_gendisk() if resumewait is true and resume_file
is in integer format to work around this problem.
Signed-off-by: Minho Ban <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The core suspend/hibernation code calls usermodehelper_disable() to
avoid race conditions between the freezer and the starting of
usermode helpers and each code path has to do that on its own.
However, it is always called right before freeze_processes()
and usermodehelper_enable() is always called right after
thaw_processes(). For this reason, to avoid code duplication and
to make the connection between usermodehelper_disable() and the
freezer more visible, make freeze_processes() call it and remove the
direct usermodehelper_disable() and usermodehelper_enable() calls
from all suspend/hibernation code paths.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Cc: [email protected]
|
|
There is no reason to call usermodehelper_disable() before creating
memory bitmaps in hibernate() and software_resume(), so call it right
before freeze_processes(), in accordance with the other suspend and
hibernation code. Consequently, call usermodehelper_enable() right
after the thawing of tasks rather than after freeing the memory
bitmaps.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Cc: [email protected]
|
|
If create_basic_memory_bitmaps() fails, usermodehelpers are not re-enabled
before returning. Fix this. And while at it, reword the goto labels so that
they look more meaningful.
Signed-off-by: Srivatsa S. Bhat <[email protected]>
Cc: [email protected]
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The code related to 'freezer_test_done' is needlessly convoluted.
Refactor the code and simplify the implementation.
Signed-off-by: Srivatsa S. Bhat <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
In the hibernation call path, the kernel threads are frozen inside
hibernation_snapshot(). If we happen to encounter an error further down
the road or if we are exiting early due to a successful freezer test,
then thaw kernel threads before returning to the caller.
Signed-off-by: Srivatsa S. Bhat <[email protected]>
Acked-by: Tejun Heo <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The current device suspend/resume phases during system-wide power
transitions appear to be insufficient for some platforms that want
to use the same callback routines for saving device states and
related operations during runtime suspend/resume as well as during
system suspend/resume. In principle, they could point their
.suspend_noirq() and .resume_noirq() to the same callback routines
as their .runtime_suspend() and .runtime_resume(), respectively,
but at least some of them require device interrupts to be enabled
while the code in those routines is running.
It also makes sense to have device suspend-resume callbacks that will
be executed with runtime PM disabled and with device interrupts
enabled in case someone needs to run some special code in that
context during system-wide power transitions.
Apart from this, .suspend_noirq() and .resume_noirq() were introduced
as a workaround for drivers using shared interrupts and failing to
prevent their interrupt handlers from accessing suspended hardware.
It appears to be better not to use them for other porposes, or we may
have to deal with some serious confusion (which seems to be happening
already).
For the above reasons, introduce new device suspend/resume phases,
"late suspend" and "early resume" (and analogously for hibernation)
whose callback will be executed with runtime PM disabled and with
device interrupts enabled and whose callback pointers generally may
point to runtime suspend/resume routines.
Signed-off-by: Rafael J. Wysocki <[email protected]>
Reviewed-by: Mark Brown <[email protected]>
Reviewed-by: Kevin Hilman <[email protected]>
|
|
Using [un]lock_system_sleep() is safer than directly using mutex_[un]lock()
on 'pm_mutex', since the latter could lead to freezing failures. Hence convert
all the present users of mutex_[un]lock(&pm_mutex) to use these safe APIs
instead.
Suggested-by: Tejun Heo <[email protected]>
Signed-off-by: Srivatsa S. Bhat <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
* pm-freezer: (26 commits)
Freezer / sunrpc / NFS: don't allow TASK_KILLABLE sleeps to block the freezer
Freezer: fix more fallout from the thaw_process rename
freezer: fix wait_event_freezable/__thaw_task races
freezer: kill unused set_freezable_with_signal()
dmatest: don't use set_freezable_with_signal()
usb_storage: don't use set_freezable_with_signal()
freezer: remove unused @sig_only from freeze_task()
freezer: use lock_task_sighand() in fake_signal_wake_up()
freezer: restructure __refrigerator()
freezer: fix set_freezable[_with_signal]() race
freezer: remove should_send_signal() and update frozen()
freezer: remove now unused TIF_FREEZE
freezer: make freezing() test freeze conditions in effect instead of TIF_FREEZE
cgroup_freezer: prepare for removal of TIF_FREEZE
freezer: clean up freeze_processes() failure path
freezer: kill PF_FREEZING
freezer: test freezable conditions while holding freezer_lock
freezer: make freezing indicate freeze condition in effect
freezer: use dedicated lock instead of task_lock() + memory barrier
freezer: don't distinguish nosig tasks on thaw
...
|
|
The hibernation test modes 'test' and 'testproc' are deprecated, because
the 'pm_test' framework offers much more fine-grained control for debugging
suspend and hibernation related problems.
So, remove the deprecated 'test' and 'testproc' hibernation test modes.
Suggested-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Srivatsa S. Bhat <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
Commit 2aede851ddf08666f68ffc17be446420e9d2a056 (PM / Hibernate: Freeze
kernel threads after preallocating memory) moved the freezing of kernel
threads to hibernation_snapshot() function.
So now, if the call to hibernation_snapshot() returns early due to a
successful hibernation test, the caller has to thaw processes to ensure
that the system gets back to its original state.
But in SNAPSHOT_CREATE_IMAGE hibernation ioctl, the caller does not thaw
processes in case hibernation_snapshot() returned due to a successful
freezer test. Fix this issue. But note we still send the value of 'in_suspend'
(which is now 0) to userspace, because we are not in an error path per-se,
and moreover, the value of in_suspend correctly depicts the situation here.
Signed-off-by: Srivatsa S. Bhat <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
In the software_resume() function defined in kernel/power/hibernate.c,
if the call to create_basic_memory_bitmaps() fails, the usermodehelpers
are not enabled (which had been disabled in the previous step). Fix it.
Signed-off-by: Srivatsa S. Bhat <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
The goto statements in hibernation_snapshot() are a bit complex.
Refactor the code to remove some of them, thereby simplifying the
implementation.
Signed-off-by: Srivatsa S. Bhat <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc into pm-freezer
* 'pm-freezer' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc: (24 commits)
freezer: fix wait_event_freezable/__thaw_task races
freezer: kill unused set_freezable_with_signal()
dmatest: don't use set_freezable_with_signal()
usb_storage: don't use set_freezable_with_signal()
freezer: remove unused @sig_only from freeze_task()
freezer: use lock_task_sighand() in fake_signal_wake_up()
freezer: restructure __refrigerator()
freezer: fix set_freezable[_with_signal]() race
freezer: remove should_send_signal() and update frozen()
freezer: remove now unused TIF_FREEZE
freezer: make freezing() test freeze conditions in effect instead of TIF_FREEZE
cgroup_freezer: prepare for removal of TIF_FREEZE
freezer: clean up freeze_processes() failure path
freezer: kill PF_FREEZING
freezer: test freezable conditions while holding freezer_lock
freezer: make freezing indicate freeze condition in effect
freezer: use dedicated lock instead of task_lock() + memory barrier
freezer: don't distinguish nosig tasks on thaw
freezer: remove racy clear_freeze_flag() and set PF_NOFREEZE on dead tasks
freezer: rename thaw_process() to __thaw_task() and simplify the implementation
...
|
|
The hibernation core code forgets to release memory preallocated
for hibernation if there's an error in its early stages or if test
modes causing hibernation_snapshot() to return early are used. This
causes the system to be hardly usable, because the amount of
preallocated memory is usually huge. Fix this problem.
Reported-by: Srivatsa S. Bhat <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
Acked-by: Srivatsa S. Bhat <[email protected]>
|
|
freeze_processes() failure path is rather messy. Freezing is canceled
for workqueues and tasks which aren't frozen yet but frozen tasks are
left alone and should be thawed by the caller and of course some
callers (xen and kexec) didn't do it.
This patch updates __thaw_task() to handle cancelation correctly and
makes freeze_processes() and freeze_kernel_threads() call
thaw_processes() on failure instead so that the system is fully thawed
on failure. Unnecessary [suspend_]thaw_processes() calls are removed
from kernel/power/hibernate.c, suspend.c and user.c.
While at it, restructure error checking if clause in suspend_prepare()
to be less weird.
-v2: Srivatsa spotted missing removal of suspend_thaw_processes() in
suspend_prepare() and error in commit message. Updated.
Signed-off-by: Tejun Heo <[email protected]>
Acked-by: Srivatsa S. Bhat <[email protected]>
|
|
Commit 2aede851ddf08666f68ffc17be446420e9d2a056
(PM / Hibernate: Freeze kernel threads after preallocating memory)
postponed the freezing of kernel threads to after preallocating memory
for hibernation. But while doing that, the hibernation test TEST_FREEZER
and the test mode HIBERNATION_TESTPROC were not moved accordingly.
As a result, when using these test modes, it only goes upto the freezing of
userspace and exits, when in fact it should go till the complete end of task
freezing stage, namely the freezing of kernel threads as well.
So, move these points of exit to appropriate places so that freezing of
kernel threads is also tested while using these test harnesses.
Signed-off-by: Srivatsa S. Bhat <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>
|
|
These files were getting <linux/module.h> via an implicit non-obvious
path, but we want to crush those out of existence since they cost
time during compiles of processing thousands of lines of headers
for no reason. Give them the lightweight header that just contains
the EXPORT_SYMBOL infrastructure.
Signed-off-by: Paul Gortmaker <[email protected]>
|